Hobbico Z1020 Droneview 1080P Wi-Fi Camera User Manual DIDE05xx Dromida XL indd

Download:
Mirror Download [FCC.gov]
Document ID	3066771
Application ID	eeiq92V4yUsqFXipnl23rQ==
Document Description	Users Manual Part Two
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	93.79kB (1172406 bits)
Date Submitted	2016-07-18 00:00:00
Date Available	2016-07-18 00:00:00
Creation Date	2016-07-18 10:31:55
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2016-07-18 10:31:55
Document Title	DIDE05xx Dromida XL.indd
Document Creator	Adobe InDesign CC 2015 (Windows)
Document Author:	mmorenz

MOTOR REPLACEMENT
4. There are four screws holding
each motor cover to the frame.
Remove all four motor covers
from the frame. The motors
should come out with the
covers. Disconnect the motors
and set the covers aside. We
recommend labelling each
cover so they are installed
back in the correct locations.
1. Remove the four screws from
the black motor cover and lift
it off the frame (if installed, the
prop guard will also need to
be removed before the motor
cover can be removed).
2. D i s c o n n e c t t h e m o t o r
connector. Grasp the motor
by the gear with your
finger tips and slide the
motor out of the cover.
5. Remove the three lens covers
from the underside of the
frame. Notice that there are
three different screw sizes so
far in this procedure. Make
a note of the sizes used in
the different holes to make
reassembly easier.
3. Slide the rubber banding off
of the old motor and onto your
replacement motor.
4. Reinstall the parts in the same
order in which they were
removed.
NOTE: There are clockwise and
counter-clockwise rotating motors.
Be sure that you are replacing a
damaged motor with the correct
part by confirming the wire colors
of the replacement motor match the motor wires you are removing.
6. Unscrew the camera connector
and the battery connector from
the frame.
NOTE: Before moving on to step 7,
take a close look at how the wires
and LEDs are positioned in the
frame. Take a photo if possible for
future reference. The wires should
be reinstalled with the new board
as they are currently placed.
FLIGHT CONTROL BOARD REPLACEMENT
Replacing the flight control board is not a difficult procedure, but there are many
screws that need to be taken out to remove the flight control board from the
quad. Have a clean work space prepared and we recommend using a container
to hold all the screws.
1. If equipped, remove the
camera by pushing down on
the camera retainer tab and
sliding the camera forward.
Disconnect the camera wire
from the quad.
2. Remove the three camera
mount screws and lift the
camera mount off the frame.
7. There are four screws that secure the flight control board to the frame. These
screws are different than the other screws removed so far. Make sure you
use them in the correct location during reassembly. Lift the board off the
frame and start feeding the wires out through the holes in the frame. If the
foam sleeves came off, slide them back on to the screw bosses as shown
in the picture.
3. Remove the six screws
securing the canopy and lift
the canopy off the frame.
8. Reassembly is the reverse of steps 1-7. Take care when installing the covers
to not pinch or sever the wires with screws. If a part does not feel like it is
fitting back into place properly, do not force it. Check that the part is properly
aligned and that the wires and LEDs are not interfering with the installation.
9. Before attempting to fly your Dromida XL, recalibrate the sensors.
BATTERY PRECAUTIONS
90-DAY LIMITED WARRANTY
The Dromida XL uses a lithium polymer (LiPo) battery. Follow these
precautions to ensure safe and trouble-free operation.
PLEASE DO NOT RETURN YOUR PRODUCT TO THE STORE. Dromida will
repair or replace factory defects for 90 days from the date of purchase. This
warranty specifically does not cover crash damage, misuse or abuse. To make
a warranty claim, please contact our product support team at 1-217-3988970 option 6 or e-mail us at helihotline@greatplanes.com. If requested
by Product Support, please send defective product to:
• ALWAYS disconnect the battery from the quadcopter when not in use.
• Do not attempt to use this charger with NiCd or NiMH battery packs.
• Do not attempt to use a damaged battery.
• This product contains a LiPo battery that must be recycled or disposed
Hobby Services
3002 N Apollo Dr., Suite #1
Champaign, IL 61822
of properly.
In the European Union, send it postpaid and insured to:
• Do not leave the charger unattended while charging. Disconnect the
Service Abteilung Revell GmbH
Henschelstrasse 20-30
32257 Bünde Germany
battery and unplug the charger immediately if either becomes hot!
However, it is normal for the charger to get warm.
• Disconnect
Tel: 01805-110111
(nur für Deutschland)
E-mail: Hobbico-Service@Revell.de
the battery from the charger and carefully move the
battery to a fireproof location if the battery begins to swell or smoke!
Please include a note about the problem, your contact information, and a
copy of the receipt.
• Never allow the battery temperature to exceed 140° F [60° C].
This warranty applies only if the product is operated in compliance with the
instructions and warnings provided with each model. Dromida assumes no
liability except for the exclusive remedy or repair of parts as specified above.
Dromida shall not be liable for consequential or incidental damages. Some
states do not allow the exclusion of consequential or incidental damages so
the above exclusion may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
• Do not attempt to charge a battery if it is swollen or hot.
• Do not place the charger or any battery on a flammable surface or
near combustible materials while in use.
• Never disassemble or modify pack wiring in any way or puncture cells.
• Never charge inside a vehicle.
• Always disconnect the battery and unplug the charger when not in use. FCC IC PRECAUTIONS
• Land your model immediately when the LEDs flash to indicate that the IC RSS warning
battery power is low. Recharge the battery before attempting another
flight. A dangerous situation can occur when attempting to recharge
an over-discharged battery!
This device complies with Industry Canada licence-exempt RSS standard (s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference,including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareilsradioexemptsdelicence. 
L'exploitationestautoriséeauxdeuxconditionssuivantes: 
(1)l'appareilnedoitpasproduiredebrouillage,et 
(2)l'utilisateurdel'appareildoitacceptertoutbrouillageradioélectriquesubi,même
silebrouillageestsusceptibled'encompromettrelefonctionnement.
• ALWAYS keep a supply of sand accessible when charging. Dumping
sand on the battery will extinguish a LiPo chemical fire.
• ALWAYS KEEP OUT OF REACH OF CHILDREN
SAFETY PRECAUTIONS
Follow these safety precautions when operating this or any model
quadcopter.
IC Radiation Exposure Statement:
This equipment complies with IC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
• Adult supervision required.
• Before flying, go to www.knowbeforeyoufly.org.
• Do not touch the spinning blades or fly over another person’s head.
• Keep your face and body as well as all spectators away from the
This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
IC exposition aux radiations:
Cet équipement est conforme avec IC les limites d'exposition aux
rayonnements définies pour un contrôlé environnement.
Cet émetteur ne doit pas être co-localisés ou fonctionner en conjonction avec
une autre antenne ou émetteur.
rotors whenever the battery is connected.
• Stay clear of buildings, trees and power lines. AVOID flying in or near
Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance
entre le radiateur et votre corps.
crowded areas. DO NOT fly close to people, children or pets.
• Maintain a safe pilot-to-quadcopter distance while flying.
• Your Dromida XL quadcopter should not be considered a toy, but rather
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
a small, working model. If not operated correctly, the model could
possibly cause injury to you or spectators and damage to property.
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other
• You must check the operation of the model before every flight to
ensure that the model has remained structurally sound.
antenna or transmitter.
• Do not alter or modify the model, as doing so may result in an unsafe
or unflyable model.
• Do your part in preserving the integrity of the FPV hobby. Know
the boundaries of your flying area and ALWAYS respect the
privacy of others.
CE COMPLIANCE INFORMATION
FOR THE EUROPEAN UNION
STATEMENTS: This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
INSTRUCTIONS FOR DISPOSAL OF WASTE EQUIPMENT BY PRIVATE USERS
IN THE EUROPEAN UNION:
This symbol on the product or its packaging indicates this product
must not be disposed of with other household waste. Instead, it is
the user’s responsibility to dispose of their waste equipment by
handing it over to a designated collection point for the recycling
of waste electrical and electronic equipment. The separate collection and
recycling of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects
human health and the environment. For more information about where you
can drop off your waste equipment for recycling, please contact your local
city office, your household waste disposal service or location where you
purchased the product.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
DECLARATION OF CONFORMITY:
Product: Dromida 2.4GHz 4-Channel Tx Rx
Item number: DIDJ1106 MR101
Equipment class: 1
● Increase the separation between the equipment and receiver.
FCC ID: IYFMR101
● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
MR101 transmitter: The objects of the declaration described here are
in conformity with the requirements of the specifications listed below, OPTIONAL BATTERY AND CHARGERS
following the provisions of the European 2006/95/EC Low Voltage
The battery included with the Dromida XL is a standard sized 2200mAh 7.4V LiPo.
Directive:
The Flight Power FP30 7.4V 2200mAh 30C would be an acceptable substitute.
EN 60950-1:2013 Safety
FPWP 3222 FlightPower LiPo FP30 2S 7.4V 2200mAh 30C Star Plug
The objects of the declaration described here are in conformity with the
requirements of the specifications listed below, following the provisions
of the European R&TTE dfirectfive 1999/5/EC:
There are many chargers on the market that are capable of charging the LiPo
included with the Dromida XL as well as other battery sizes and chemistries.
Here are a few chargers that we recommend as upgrades to the charger included
with the Dromida XL:
EN300 328 V1.9.1.
DTXP4225 Duratrax Onyx 225 AC/DC
Advanced Charger
Technical requirements for radio equipment
ETSI EN 301 489-1 V1.9.1, 301 489-17 V2.2.1 General EMC
requirements for radio equipment
Hobbico, Inc.
2904 Research Road
Champaign, IL USA 61826
Distributed in Europe by Revell GmbH
D-32257 Bünde Germany
DTXP4255 Duratrax Onyx 255 AC/DC
Dual Balancing Charger
The associated regulatory agencies of the following countries recognize
the noted certifications to this product as authorized for sale and use.
UK
EE
RO
NL
DE
LV
SI
LU
DK
LT
AT
MT
BG
PL
IT
CY
SE
CZ
ES
FI
SK
PT
GR
HU
IE
GPMM3155 Great Planes
ElectriFly Triton
EQ AC/DC Charger
IC:11104A-DRONEVIEW
REPLACEMENT PARTS
1 DIDE1240
2 DIDE1241
DIDE1242
DIDE1243
DIDE1244
3 DIDE1245
DIDE1246
DIDE1247
DIDE1248
4 DIDE1249
5 DIDE1250
6 DIDE1251
DIDE1252
DIDE1253
DIDE1254
7 DIDE1255
8 DIDE1256
9 DIDE1257
10 DIDE1258
DIDE1259
DIDE1260
DIDE1261
11
Prop Guard Set
Prop Set Blue
Prop Set Green
Prop Set Orange
Prop Set Red
Canopy Green
Canopy Blue
Canopy Orange
Canopy Red
Canopy Air Damper
Bearing Set
Main Frame Green
Main Frame Blue
Main Frame Orange
Main Frame Red
Spur Gear Set
Prop Shaft
Motor Cover
LED Arm Covers Orange
LED Arm Covers Blue
LED Arm Covers Green
LED Arm Covers Red
12
13
14
15
15
16
17
18
19
20
TO CONVERT XL UAV TO FPV
13 DIDE1264
15 TACZ1020
TACZ1010
Camera Mount Assembly
DroneView 1080P Wi-Fi Camera
Tactic 4GB C10 Micro Memory Card
(or equivalent up to 32GB)
10
DIDE1262
DIDE1270
DIDE1271
DIDE1272
DIDE1263
DIDE1264
DIDE1265
TACZ1020
TACZ1005
DIDE1235
DIDE1266
DIDE1267
DIDE1268
DIDE1269
E-Board with Barometer Orange
E-Board with Barometer Green
E-Board with Barometer Blue
E-Board with Barometer Red
E-Board Dampers
Camera Mount Assembly XL FPV Only
Landing Pads
DroneView 1080P Wi-Fi Camera FPV Only
Camera Power Wire
2S, 2200mAh 7.4V LiPo Battery
Main Motors CW Left Front, Right Rear
Main Motors CCW Right Front, Left Rear
Screw Set
Camera Mount Dampers FPV Only
DIDJ1106
DIDE1236
DIDE1237
DIDE1215
TACZ1010
MR101 Transmitter
2S/3S Balance Charger
A/C Adaptor 2S/3S Balance Charger
TX Mobile Phone Holder
4GB Class 10 Memory card FPV Only
EXPLODE VIEW
11
12
10
13
17
20
18
14
19
10
16
15
Bold = FPV parts
only
11
TO PREVENT MOTOR DAMAGE ALWAYS BE SURE THE THROTTLE IS
OFF WHEN THE BLADES ARE OBSTRUCTED OR CONTROL IS LOST.
PRESS AND HOLD THE MOTOR OFF PANIC BUTTON!
© 2016 Dromida, a Hobbico® company
dromida.com
DIDE05xx DIDE06xx

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : mmorenz
Create Date                     : 2016:07:18 10:31:55-07:00
Modify Date                     : 2016:07:18 10:31:55-07:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Producer                        : Acrobat Distiller 11.0 (Windows)
Trapped                         : False
Creator Tool                    : Adobe InDesign CC 2015 (Windows)
Metadata Date                   : 2016:05:20 15:25:28-05:00
Format                          : application/pdf
Creator                         : mmorenz
Title                           : DIDE05xx Dromida XL.indd
GTS PDFX Conformance            : PDF/X-1a:2001
GTS PDFX Version                : PDF/X-1:2001
Version ID                      : 1
Document ID                     : uuid:351ab5e5-699b-5048-9263-6fb685a0d775
Instance ID                     : uuid:7d8dcabd-ef15-4f64-a96c-2597abffe0c1
Page Count                      : 6

EXIF Metadata provided by EXIF.tools