Honeywell Security Sensor CoE PP300850SE DUAL TEC Motion Sensor User Manual 800 13827 B DT8050A QIG 12 10 13

Download:
Mirror Download [FCC.gov]
Document ID	2186697
Application ID	0WU4imdj/UFuE3CyaqBGGA==
Document Description	User Manual (1 of 2).PDF
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	81.75kB (1021903 bits)
Date Submitted	2014-02-11 00:00:00
Date Available	2014-03-27 00:00:00
Creation Date	2013-12-10 05:54:16
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2013-12-20 10:50:13
Document Title	Microsoft Word - 800-13827-B_DT8050A-QIG_12-10-13
Document Creator	PScript5.dll Version 5.2.2
Document Author:	E727032

DRAFT - QUICK INSTALL GUIDE - 12/10/13
DT8050A
DT8050A
DT8050A
DT8050A
DUAL TEC® Motion Sensor with Anti-Mask
DUAL TEC® Motion Sensor with Anti-Mask
DUAL TEC® Motion Sensor with Anti-Mask
DUAL TEC® Motion Sensor with Anti-Mask
Quick Installation Guide
Quick Installation Guide (FR)
Quick Installation Guide (SP)
Quick Installation Guide (PG)
12”
(30 cm)
6' 9" - 8' 9"
(2.1 - 2.7 m)
7' 6"
Optimal (2.3
m)
Optimal
Optimal
Optimal
* Keep Clear / Tenir à l'écart /
Respetar obligatoriamente /
Manter-se afastado
#6
(3.5 mm)
#6 x 1 1/4"
(3.5 mm x 32 mm)
B A
Internal EOL Resistor DIP Switches
Résistance interne EOL commutateur DIP
Interruptores DIP internos EOL Resistor
EOL interno Resistor DIP Switches
Anti-mask
Anti-masque
Antienmascaramiento
Anti-máscara
DT8050A
EOL
KOhm
ON
ON
1 2 2.2 5.6
AM LED
ON
OFF
MAX
PULL
TO DISABLE
LOOK DOWN
Enabled
Activé
Habilitado
Habilitado
ON
EOL
KOhm 1 2 2.2 5.6
MW
SENSITIVITY
W1
LOOK DOWN
ON
LED
OFF
*Disabled
*Désactivé
*Deshabilitado
*Deshabilitado
Microwave Range Adjustment
Réglage de la portée Hyperfréquence
Ajuste del rango de detección Microondas
Ajuste de Alcance Microondas
MAX
MIN
MW
SENSITIVITY
* Factory default / Réglage usine /
Defecto de fábrica / Padrão de fábrica
5
24-20 AWG
(0.2-0.52mm2)
LED
0 VDC - Vsupply
1.8 mA max
Trouble
30 mA
25 VDC
Tamper
30 mA
25 VDC
LED TBL TBL T
Alarm
30 mA
25 VDC
Power
18 mA
9 - 15 VDC
NC V
- V+
EOL
9 8 7 6 5 4 3 2 1
ON
EOL
KOhm 1 2 2.2 5.6
WIRING EXAMPLES / WIRING EXAMPLES / WIRING EXAMPLES / WIRING EXAMPLES
FR) To connect all three outputs (sensor alarm, tamper and
trouble/anti-mask) to one zone input: All alarm, tamper and
trouble/anti-mask events are “alarms” when the system is armed or “fault”
when disarmed.
ES) To connect all three outputs (sensor alarm, tamper and
trouble/anti-mask) to one zone input: All alarm, tamper and
trouble/anti-mask events are “alarms” when the system is armed or “fault”
when disarmed.
PG) To connect all three outputs (sensor alarm, tamper and
trouble/anti-mask) to one zone input: All alarm, tamper and
trouble/anti-mask events are “alarms” when the system is armed or “fault”
when disarmed.
Control Panel
Zone
Zone
COM
Ground +12V
T C NC V- V+
9 8 7 6 5 4 3 2 1
LED TBL TBL T
Sensor
To connect all three outputs (sensor alarm, tamper and trouble/antimask) to one zone input: All alarm, tamper and trouble/anti-mask
events are “alarms” when the system is armed or “fault” when disarmed.
(On-Board, Internal EOLR)
Anti-mask
Enabled
EOL
ON
ON
EOL
KOhm 1 2 2.2 5.6
Note: A masking condition can occur when blocking or reflective material is placed in front of the sensor.
of the sensor clear.
Note: A masking condition can occur when blocking or reflective material is placed in front of the sensor.
of the sensor clear.
Note: A masking condition can occur when blocking or reflective material is placed in front of the sensor.
of the sensor clear.
Note: A masking condition can occur when blocking or reflective material is placed in front of the sensor.
of the sensor clear.
To connect the sensor alarm output to one zone input and the
tamper and trouble/anti-mask outputs to a second zone input: The
alarm relay is wired to one zone; the tamper and trouble/anti-mask are
wired to another zone; the control panel differentiates alarm conditions
from tamper and trouble/anti-mask conditions.
To connect the sensor alarm output to one zone input and the
tamper and trouble/anti-mask outputs to a second zone input: The
alarm relay is wired to one zone; the tamper and trouble/anti-mask are
wired to another zone; the control panel differentiates alarm conditions
from tamper and trouble/anti-mask conditions.
To connect the sensor alarm output to one zone input and the
tamper and trouble/anti-mask outputs to a second zone input: The
alarm relay is wired to one zone; the tamper and trouble/anti-mask are
wired to another zone; the control panel differentiates alarm conditions
from tamper and trouble/anti-mask conditions.
-2-
Keep 12” (30cm) in front
Keep 12” (30cm) in front
Keep 12” (30cm) in front
Control Panel
Trouble
Zone
Zone Alarm
COM Zone Ground +12V
JUMPER
V- V+
9 8 7 6 5 4 3 2 1
LED TBL TBL T
NC
(On-Board, Internal EOLR)
EOL
ON
Anti-mask
Enabled
W1
ON
EOL
KOhm 1 2 2.2 5.6
* Off-Board, External EOLR (Not supplied),
best if installed inside the sensor housing.
Cut
Sensor
To connect the sensor alarm output to one zone input and the
tamper and trouble/anti-mask outputs to a second zone input: The
alarm relay is wired to one zone; the tamper and trouble/anti-mask are
wired to another zone; the control panel differentiates alarm conditions
from tamper and trouble/anti-mask conditions.
Keep 12” (30cm) in front
Control Panel
To connect the sensor alarm, tamper and trouble/anti-mask outputs
to three separate zone inputs: The alarm, tamper and trouble/anti-mask
are each wired to a separate zone; the control panel differentiates alarm,
tamper and trouble/anti-mask conditions.
Trouble Zone
Zone COM
Tamper Zone Alarm
Zone COM Zone Ground +12V
V- V+
9 8 7 6 5 4 3 2 1
LED TBL TBL T
To connect the sensor alarm, tamper and trouble/anti-mask outputs
to three separate zone inputs: The alarm, tamper and trouble/anti-mask
are each wired to a separate zone; the control panel differentiates alarm,
tamper and trouble/anti-mask conditions.
NC
Sensor
To connect the sensor alarm, tamper and trouble/anti-mask outputs
to three separate zone inputs: The alarm, tamper and trouble/anti-mask
are each wired to a separate zone; the control panel differentiates alarm,
tamper and trouble/anti-mask conditions.
(On-Board, Internal EOLR)
To connect the sensor alarm, tamper and trouble/anti-mask outputs
to three separate zone inputs: The alarm, tamper and trouble/anti-mask
are each wired to a separate zone; the control panel differentiates alarm,
tamper and trouble/anti-mask conditions.
Anti-mask
Enabled
EOL
ON
W1
ON
Cut
EOL
KOhm 1 2 2.2 5.6
* Off-Board, External EOLR (Not supplied),
best if installed inside the sensor housing.
Walk Test Reset
MAX
30 sec
ON
< 4 ft /1.2m
MIN
MW
SENSITIVITY
4X
(slowly)
10
45
AM LED
20
30
Top View
Vue de dessus
Vista Desde Arriba
Vista Superior
PLAN VIEW
ALL ZONES
Power
Up
Walk Test
Normal
Trouble
AntiMask
Red
Slow
Blink
ON
Alarm
ON
Alarm
Fast
Blink
OFF
Yellow
OFF
ON
Microwave
ON
Microwave
OFF
Fast
Blink
Green
OFF
ON PIR
ON PIR
OFF
OFF
Side View
Vue de coté
Vista Lateral
Vista Lateral
40’
12 m
33’
10 m
27’
8m
20’
6m
13’
4m
7’
2m
2.3m
1.85
0.5
7’ 13’ 20’ 27’ 33’ 40’ 46’ 53’
2 m 4 m 6 m 8 m 10 m 12 m 14 m 16 m
A B
Zones / Zones / Zonas / Zonas
7’
2m
13’
4m
20’
6m
27’
8m
33’
10 m
40’
12 m 0
LED
7’ 13’ 20’ 27’ 33’ 40’ 46’ 53’
2 m 4 m 6 m 8 m 10 m 12 m 14 m 16 m
-3-
Look-down / Basses / Vista Zona 0 /
Vigilância inferior
12
Lower / Courtes / Cercana/ Mais baixas
10
Intermediate / Intermédiaires / Intermedia /
Intermédias
36
Long / Longues / Largo Alcance / Longo
alcance
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your
information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the
manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for
a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection
against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les
interférences causant une réception indésirable.
APPROVAL/ LISTINGS:
•
•
•
•
•
FCC part 15, Class B verified
IC ICES-003, Class B verified
UL 639
ULC S306-03
SIA-PIR-01 Passive Infrared detector standard features for false alarm immunity.
Product must be tested at least once each year.
For appropriate wiring methods, refer to the National Electrical Code NFPA 70 and the Canadian Electrical Code (where applicable).
Power must be provided by a power-limited UL603 Listed burglar alarm power supply with minimum 4 hours of standby power capability, or from a
power-limited output of a UL Listed burglar alarm control unit with minimum 4 hours of standby power capability.
For the latest documentation and online support information, please go to:
Pour de l’assistance en ligne, visitez :
Para recibir soporte en línea, visite:
Para qualquer informação adicional, contacte:
http://www.security.honeywell.com/hsc/resources/MyWebTech/
To protect the environment, a detailed installation guide is available on
the Honeywell website – Please consider before printing the document!
For the latest U.S. warranty information, please go to: www.honeywell.com/security/hsc/resources/wa or
Please contact your local authorized Honeywell representative for product warranty information.
Pour obtenir de l'information sur la garantie de ce produit, veuillez communiquer avec le représentant autorisé de Honeywell
de votre région.
Por favor contacte con su distribuidor Honeywell Security para información sobre la garantía del producto.
Contacte o representante autorizado Honeywell local para obter informações relativas a garantia.
 2013 Honeywell International Inc. Honeywell and DUAL TEC are registered trademarks of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved. Made in China.
-4-
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
www.honeywell.com/security
P/N 800-13827 12/13 Rev B

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Format                          : application/pdf
Creator                         : E727032
Title                           : Microsoft Word - 800-13827-B_DT8050A-QIG_12-10-13
Create Date                     : 2013:12:10 05:54:16
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2013:12:20 10:50:13+08:00
Metadata Date                   : 2013:12:20 10:50:13+08:00
Producer                        : GPL Ghostscript 8.15
Document ID                     : uuid:e574d5df-6bb0-4376-97ae-9f528ac53e70
Instance ID                     : uuid:6203fcfd-85f6-46cd-ae83-b267b9b19626
Has XFA                         : No
Page Count                      : 4
Author                          : E727032

EXIF Metadata provided by EXIF.tools