Honeywell LXEMX9GSM2G IPDA User Manual MX9 User Guide Draft

Honeywell International, Inc. IPDA MX9 User Guide Draft

Users Manual_100414

Draft01-For review only - Do not publish or distribute - LXE ConfidentialMX9User GuideE-EQ-MX9OGWW-C2010 Copyright© by LXE®, Inc, An EMS Technologies Company. All RightsReserved.
NoticesLXE Inc. reserves the right to make improvements or changes to published MX9 information at any time without notice. Whilereasonable efforts have been made in the preparation of this publication to assure its accuracy, LXE assumes no liabilityresulting from any errors or omissions in this publication, or from the use of the information contained herein. Further, LXEIncorporated, reserves the right to revise this publication and to make changes to it from time to time without any obligation tonotify any person or organization of such revision or changes.TrademarksCopyright © 2010 by LXE Inc., An EMS Technologies Company, 125 Technology Parkway, Norcross, GA 30092 U.S.A. (770)447-4224LXE® and Spire® are registered trademarks of LXE Inc.Microsoft®, ActiveSync®, MSN, Outlook®, Windows®, Windows Mobile®, the Windows logo, and Windows Media areeither registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.Intel and Intel XScale are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States andother countries.Summit Data Communications, Inc. Summit Data Communications, the Summit logo, and “The Pinnacle of Performance” aretrademarks of Summit Data Communications, Inc.The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LXE, Inc. is underlicense.PowerScan is a registered trademark of Datalogic Scanning, Inc., located in Eugene, OR.Symbol® is a registered trademark of Symbol Technologies. MOTOROLA® and the Stylized M Logo are registeredtrademarks of Motorola®, Inc.Hand Held® is a registered trademark of Hand Held Products, Inc., located in Skaneateles Falls, NY.RAM® and RAM Mount™ are both trademarks of National Products Inc., 1205 S. Orr Street, Seattle, WA 98108.When any part of this publication is in PDF format: “Acrobat ® Reader Copyright © 2010 Adobe Systems Incorporated. Allrights reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated”applies.Other product names mentioned within this publication may be trademarks or registered trademarks of other companies.
Table of ContentsComponents 1Front 1Top 3Bottom 4Back 4Handstrap 5Label Locations 6Laser Warnings and Labels 7Label Location 7Label 7Batteries 8How To Connect or Remove the Battery Pack 8Insert/Replace Battery 8Remove Battery 8Hotswap the Main Battery 9Regulatory Notices and Safety Information 10Class B Digital Device 10RF Notices 11Laser Light Safety Statement 12Index 14E-EQ-MX9OGWW-C Draft 01 [ i ] MX9 User Guide
ComponentsFront1. Microphone2. Touch screen3. Speaker4. Scan buttons5. Enter key6. Scanner status LED7. Power keyNote: The above list is the same on the 38 key MX9. Special keys arelisted below.E-EQ-MX9OGWW-C Draft 01 [ 1 ] MX9 User Guide
FrontFor review only - Do not publish or distribute - LXE Confidential - Draft 01Special Purpose Keys1. Function Keys2. Cursor up and down Keys3. Diamond 1 key4. Backspace [BS] key and Space[SPC] key5. Escape [ESC] key6. Power key7. Tab key8. Alt key9. Control [CTL] key10. Shift [SHFT] key11. Blue key12. Orange keyE-EQ-MX9OGWW-C Draft 01 [ 2 ] MX9 User Guide
TopFor review only - Do not publish or distribute - LXE Confidential - Draft 01Special Purpose Keys - 38 Key1. Function keys2. Tab | Space | Backspacekeys3. Diamond 2 key4. Orange key5. Escape [ESC] key6. Alpha key7. Control [CTRL] key8. Shift [SHIFT] key9. Cursor up and down keys10. Blue key11. Alt keyTopBarcode reader Scanner apertureE-EQ-MX9OGWW-C Draft 01 [ 3 ] MX9 User Guide
BottomFor review only - Do not publish or distribute - LXE Confidential - Draft 01BottomInput / Output ConnectorTethered boot cover (covers I/O connector) not shownBackBattery Bay1. Battery Terminals2. Battery Bay3. Battery Bay Access TabE-EQ-MX9OGWW-C Draft 01 [ 4 ] MX9 User Guide
HandstrapFor review only - Do not publish or distribute - LXE Confidential - Draft 01Handstrap1. Handstrap2. Handstrap Base3. Stylus1. Attach - Upper Handstrap Base2. Attach - Lower Handstrap Base1. Handstrap connector, upper2. Stylus holder on Handstrap3. Handstrap connector, lowerE-EQ-MX9OGWW-C Draft 01 [ 5 ] MX9 User Guide
Label LocationsFor review only - Do not publish or distribute - LXE Confidential - Draft 01Label Locations1. Laser Warning Label2. Bluetooth Label3. Product Identification Label4. Reserved5. Windows CE License Label6. Tamper Proof LabelThe tamper-proof label covers the top right screw in the battery bay. The label states"Warranty void if removed or damaged". The battery pack will not deface the label asthe battery pack does not touch the label.Device with Summit RadioE-EQ-MX9OGWW-C Draft 01 [ 6 ] MX9 User Guide
Laser Warnings and LabelsLaser Warnings and LabelslDo not look into the laser’s lens.lDo not stare directly into the laser beam.lDo not remove the laser caution labels from the MX9.lDo not connect the laser barcode aperture to any other device. The laser barcode aperture is certified for use with theMX9 only.Caution:Laser radiation when open. Please read the caution labels. Use of controls, adjustments or performance of pro-cedures other than those specified herein may result in hazardous radiation exposure.Label LocationLabelE-EQ-MX9OGWW-C [ 7 ] MX9 User Guide
BatteriesBatteriesHotswap the Main BatteryHow To Connect or Remove the Battery PackWarning: Never remove or replace any battery in a hazardous location.The MX9 will not function unless the battery pack is in place and securely latched.Be sure to place the unit in Suspend Mode (by pressing the Power key or tapping Start | Suspend) before removing the battery.Failing to properly place the device in Suspend mode will result in a loss of all unsaved data.The main battery is located in a compartment on the back of the unit. The battery case serves as the back cover for the batterywell of the MX9.An MX9 will retain data, while the main battery is removed and replaced with a fully charged main battery, for 5 minutes.Important: When the backup battery power is Low or Very Low connect the AC adapter to the MX9 before replacing the mainbattery.Note: The battery should not be replaced in a dirty, harsh or hazardous environment. When the battery is not connected tothe MX9, any dust or moisture that enters the battery well or connector may transfer to the battery/well terminals,potentially causing damage.Warning: Only use LXE MX9380BATTERY batteries as replacements.Insert/Replace BatteryTo insert the main battery, complete the following steps:1. Detach the bottom hook of the handstrap (if installed).2. Tilt the end (with the terminals) of the fully charged battery pack into the upper end of the battery compartment, andfirmly press the other end until it is fully inserted into the battery compartment.3. Push down on the battery until the retaining clip clicks into place.4. Replace the handstrap clip in its holder (if installed).The MX9 draws power from the battery immediately upon successful connection.Check battery status by tapping the Start | Settings | Control Panel | Battery icon. Main battery level, status and otherdetails are displayed.Remove BatteryTo remove the battery, complete the following steps:1. Place the MX9 in Suspend mode.2. Detach the bottom hook of the handstrap (if installed).3. Slide the battery retaining clip down to release the main battery.4. Pull the battery up and out of the battery well with a hinge motion.Place the discharged battery pack in a powered battery charger.E-EQ-MX9OGWW-C [ 8 ] MX9 User Guide
Hotswap the Main BatteryHotswap the Main BatteryWarning: Never replace (hotswap) the MX9 battery in a hazardous location.Place the MX9 in Suspend Mode. LXE recommends any work in progress be saved prior to replacing the battery pack.Simply replace the discharged battery with a fully-charged battery. An MX9, with a fully charged backup battery, will retain dataduring a battery hotswap for 5 minutes.E-EQ-MX9OGWW-C [ 9 ] MX9 User Guide
Regulatory Notices and Safety InformationRF NoticesWaste Electrical and Electronic Equipment (WEEE)Important:This symbol is placed on the product to remind users to dispose of Waste Electrical and Electronic Equipment(WEEE) appropriately, per Directive 2002-96-EC. In most areas, this product can be recycled, reclaimed and re-used when properly discarded. Do not discard labeled units with trash. For information about proper disposal,Contact your LXE representative, or visit www lxe com.Class B Digital DeviceNOTICEThis device complies with Part 15 of the FCC Rules [and with RSS-210 of Industry Canada]. Operation is subject to thefollowing two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:lReorient or relocate the receiving antenna.lIncrease the separation between the equipment and the receiver.lConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.lConsult the dealer or an experienced radio/TV technician for help.NOTICEChanges or modifications made to this equipment not expressly approved by LXE, Inc., may void the FCC authorization tooperate this equipment.Industry CanadaThis Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operationis subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must acceptany interference received, including interference that may cause undesired operation.Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Leprésent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériquesde Classe B prescrites dans le Règlement sur le brouillage radioélectrique édits par le ministère des Communications duCanada.Li-Ion BatteryWhen disposing of the MX9 main battery, the following precautions should be observed: The battery should be disposed ofproperly. The battery should not be disassembled or crushed. The battery should not be heated above 212°F (100°C) orE-EQ-MX9OGWW-C [ 10 ] MX9 User Guide
RF Noticesincinerated.NOTICE:This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe [*] est conforme á la norme NMB-003 du Canada.RF NoticesThis device can contain transmitter Module(s) FCC ID:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment under 47 CFR 2.1093paragraph (d)(2).R&TTE Directive Requirements (Applies only to equipment operated within the EU/EFTA)Information to UserA label on the exterior of the device should resemble one of the labels shown below (the label contains the LXE partnumber of the installed radio card). The labels shown below and affixed to the device, identify where the device maybe used and where its use is restricted. Use of a device is prohibited in countries not listed below or otherwiseidentified by the label. (May or may not include the 0560 Notified Body Number. Substitute 4 digit Notified BodyNumber may also be applied.)E-EQ-MX9OGWW-C [ 11 ] MX9 User GuideFCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. For hand-held operation only. This IPDA meets FCC RF exposure guidelines when used in hand-held.
Laser Light Safety StatementLaser Light Safety StatementWarning: This product uses laser light. One of the following labels is provided on the scanner. Please read theCaution statement. (US)Mise én garde: Ce produit utilise un rayon laser. L’une des étiquettes suivantes est apposée sur le scanneur. Veuillez lirel’avertissement qu’elle contient. (FR)Advertência: Este produto usa luz de laser. O scanner contém um dos seguintes avisos. Favor ler o Aviso. (PT)Varning: Denna produkt använder laserljus. En av de nedanstående etiketterna sitter på scannern. Var god läs varningstexten.(SE)Advarsel: Dette produkt anvender laserlys. En af følgende mærkater anvendes på scanneren. Læs venligstsikkerhedsforanstaltningen. (DK)Varoitus: Tämä tuote käyttää laservaloa. Skannerissa on jokin seuraavista tarroista. Lue Huomio-kohta. (FI)Warnung: Dieses Produkt verwendet Laserlicht. Eines der folgenden Etiketten befindet sich auf dem Scanner. Bitte lesen Sieden Gefahrenhinweis. (DE)Attenzione: Questo prodotto utilizza luce laser. Una delle etichette seguenti c’ ubicata sullo scanner. Si raccomanda di leggerecon attenzione le avvertenze riportate. (IT)Advarsel: Dette utstyret bruker laserlys. En av følgende etiketter er plassert på scanneren. Les advarselen på etiketten. (NO)Advertencia: Este producto usa luz de láser. Las etiquetas se proveen en la máquina exploradora. Por favor, leadetenidamente la explicación para las precauciones. (ES)Waarschuwing: Dit product gebruikt laserlicht. Een van de volgende labels is op de scanner aangebracht. Lees a.u.b. dewaarschuwing onder Oppassen. (NL)E-EQ-MX9OGWW-C [ 12 ] MX9 User Guide
Laser Light Safety StatementE-EQ-MX9OGWW-C [ 13 ] MX9 User Guide
IndexBBatteryInstall 8Remove 8Battery insert and remove instruction 8Bottom 4CClass B 10Component Diagrams 1ComponentsBack 4Labels 6Connect or Remove the Battery Pack 8FFront 1HHandstrap 5Hotswap the Main Battery 9IInput / Output Connector 4LLaser Light Safety Statement 12Laser Warnings and Labels 7RRegulatory Statements 10Remove Battery 8RF Notices 11SScanner aperture 3Special Purpose Keys - 38 Key 3Special Purpose Keys - 62 Key 2TTop 3WWEEE 10E-EQ-MX9OGWW-C Draft 01 [ 14 ] MX9 User Guide

Navigation menu