Honeywell LXEMX9GSM2G IPDA User Manual MX9 User Guide Draft
Honeywell International, Inc. IPDA MX9 User Guide Draft
Users Manual_100414
Draft 01 - For review only - Do not publish or distribute - LXE Confidential MX9 User Guide E-EQ-MX9OGWW-C 2010 Copyright© by LXE®, Inc, An EMS Technologies Company. All Rights Reserved. Notices LXE Inc. reserves the right to make improvements or changes to published MX9 information at any time without notice. While reasonable efforts have been made in the preparation of this publication to assure its accuracy, LXE assumes no liability resulting from any errors or omissions in this publication, or from the use of the information contained herein. Further, LXE Incorporated, reserves the right to revise this publication and to make changes to it from time to time without any obligation to notify any person or organization of such revision or changes. Trademarks Copyright © 2010 by LXE Inc., An EMS Technologies Company, 125 Technology Parkway, Norcross, GA 30092 U.S.A. (770) 447-4224 LXE® and Spire® are registered trademarks of LXE Inc. Microsoft®, ActiveSync®, MSN, Outlook®, Windows®, Windows Mobile®, the Windows logo, and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Intel and Intel XScale are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Summit Data Communications, Inc. Summit Data Communications, the Summit logo, and “The Pinnacle of Performance” are trademarks of Summit Data Communications, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LXE, Inc. is under license. PowerScan is a registered trademark of Datalogic Scanning, Inc., located in Eugene, OR. Symbol® is a registered trademark of Symbol Technologies. MOTOROLA® and the Stylized M Logo are registered trademarks of Motorola®, Inc. Hand Held® is a registered trademark of Hand Held Products, Inc., located in Skaneateles Falls, NY. RAM® and RAM Mount™ are both trademarks of National Products Inc., 1205 S. Orr Street, Seattle, WA 98108. When any part of this publication is in PDF format: “Acrobat ® Reader Copyright © 2010 Adobe Systems Incorporated. All rights reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated” applies. Other product names mentioned within this publication may be trademarks or registered trademarks of other companies. Table of Contents Components Front Top Bottom Back Handstrap Label Locations Laser Warnings and Labels Label Location Label Batteries How To Connect or Remove the Battery Pack Insert/Replace Battery Remove Battery Hotswap the Main Battery Regulatory Notices and Safety Information 10 Class B Digital Device 10 RF Notices 11 Laser Light Safety Statement 12 Index 14 E-EQ-MX9OGWW-C Draft 01 [ i ] MX9 User Guide Components Front 1. Microphone 2. Touch screen 3. Speaker 4. Scan buttons 5. Enter key 6. Scanner status LED 7. Power key Note: The above list is the same on the 38 key MX9. Special keys are listed below. E-EQ-MX9OGWW-C Draft 01 [ 1 ] MX9 User Guide Front For review only - Do not publish or distribute - LXE Confidential - Draft 01 Special Purpose Keys 1. Function Keys 2. Cursor up and down Keys 3. Diamond 1 key 4. Backspace [BS] key and Space [SPC] key 5. Escape [ESC] key 6. Power key 7. Tab key 8. Alt key 9. Control [CTL] key 10. Shift [SHFT] key 11. Blue key 12. Orange key E-EQ-MX9OGWW-C Draft 01 [ 2 ] MX9 User Guide Top For review only - Do not publish or distribute - LXE Confidential - Draft 01 Special Purpose Keys - 38 Key 1. Function keys 2. Tab | Space | Backspace keys 3. Diamond 2 key 4. Orange key 5. Escape [ESC] key 6. Alpha key 7. Control [CTRL] key 8. Shift [SHIFT] key 9. Cursor up and down keys 10. Blue key 11. Alt key Top Barcode reader Scanner aperture E-EQ-MX9OGWW-C Draft 01 [ 3 ] MX9 User Guide Bottom For review only - Do not publish or distribute - LXE Confidential - Draft 01 Bottom Input / Output Connector Tethered boot cover (covers I/O connector) not shown Back Battery Bay 1. Battery Terminals 2. Battery Bay 3. Battery Bay Access Tab E-EQ-MX9OGWW-C Draft 01 [ 4 ] MX9 User Guide Handstrap For review only - Do not publish or distribute - LXE Confidential - Draft 01 Handstrap 1. Handstrap 2. Handstrap Base 3. Stylus 1. Attach - Upper Handstrap Base 2. Attach - Lower Handstrap Base 1. Handstrap connector, upper 2. Stylus holder on Handstrap 3. Handstrap connector, lower E-EQ-MX9OGWW-C Draft 01 [ 5 ] MX9 User Guide Label Locations For review only - Do not publish or distribute - LXE Confidential - Draft 01 Label Locations 1. Laser Warning Label 2. Bluetooth Label 3. Product Identification Label 4. Reserved 5. Windows CE License Label 6. Tamper Proof Label The tamper-proof label covers the top right screw in the battery bay. The label states "Warranty void if removed or damaged". The battery pack will not deface the label as the battery pack does not touch the label. Device with Summit Radio E-EQ-MX9OGWW-C Draft 01 [ 6 ] MX9 User Guide Laser Warnings and Labels Laser Warnings and Labels Do not look into the laser’s lens. Do not stare directly into the laser beam. Do not remove the laser caution labels from the MX9. Do not connect the laser barcode aperture to any other device. The laser barcode aperture is certified for use with the MX9 only. Caution: Laser radiation when open. Please read the caution labels. Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Label Location Label E-EQ-MX9OGWW-C [ 7 ] MX9 User Guide Batteries Batteries Hotswap the Main Battery How To Connect or Remove the Battery Pack Warning: Never remove or replace any battery in a hazardous location. The MX9 will not function unless the battery pack is in place and securely latched. Be sure to place the unit in Suspend Mode (by pressing the Power key or tapping Start | Suspend) before removing the battery. Failing to properly place the device in Suspend mode will result in a loss of all unsaved data. The main battery is located in a compartment on the back of the unit. The battery case serves as the back cover for the battery well of the MX9. An MX9 will retain data, while the main battery is removed and replaced with a fully charged main battery, for 5 minutes. Important: When the backup battery power is Low or Very Low connect the AC adapter to the MX9 before replacing the main battery. Note: The battery should not be replaced in a dirty, harsh or hazardous environment. When the battery is not connected to the MX9, any dust or moisture that enters the battery well or connector may transfer to the battery/well terminals, potentially causing damage. Warning: Only use LXE MX9380BATTERY batteries as replacements. Insert/Replace Battery To insert the main battery, complete the following steps: 1. Detach the bottom hook of the handstrap (if installed). 2. Tilt the end (with the terminals) of the fully charged battery pack into the upper end of the battery compartment, and firmly press the other end until it is fully inserted into the battery compartment. 3. Push down on the battery until the retaining clip clicks into place. 4. Replace the handstrap clip in its holder (if installed). The MX9 draws power from the battery immediately upon successful connection. Check battery status by tapping the Start | Settings | Control Panel | Battery icon. Main battery level, status and other details are displayed. Remove Battery To remove the battery, complete the following steps: 1. Place the MX9 in Suspend mode. 2. Detach the bottom hook of the handstrap (if installed). 3. Slide the battery retaining clip down to release the main battery. 4. Pull the battery up and out of the battery well with a hinge motion. Place the discharged battery pack in a powered battery charger. E-EQ-MX9OGWW-C [ 8 ] MX9 User Guide Hotswap the Main Battery Hotswap the Main Battery Warning: Never replace (hotswap) the MX9 battery in a hazardous location. Place the MX9 in Suspend Mode. LXE recommends any work in progress be saved prior to replacing the battery pack. Simply replace the discharged battery with a fully-charged battery. An MX9, with a fully charged backup battery, will retain data during a battery hotswap for 5 minutes. E-EQ-MX9OGWW-C [ 9 ] MX9 User Guide Regulatory Notices and Safety Information RF Notices Waste Electrical and Electronic Equipment (WEEE) Important: This symbol is placed on the product to remind users to dispose of Waste Electrical and Electronic Equipment (WEEE) appropriately, per Directive 2002-96-EC. In most areas, this product can be recycled, reclaimed and reused when properly discarded. Do not discard labeled units with trash. For information about proper disposal, Contact your LXE representative, or visit www lxe com. Class B Digital Device NOTICE This device complies with Part 15 of the FCC Rules [and with RSS-210 of Industry Canada]. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. NOTICE Changes or modifications made to this equipment not expressly approved by LXE, Inc., may void the FCC authorization to operate this equipment. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le Règlement sur le brouillage radioélectrique édits par le ministère des Communications du Canada. Li-Ion Battery When disposing of the MX9 main battery, the following precautions should be observed: The battery should be disposed of properly. The battery should not be disassembled or crushed. The battery should not be heated above 212°F (100°C) or E-EQ-MX9OGWW-C [ 10 ] MX9 User Guide RF Notices incinerated. NOTICE: This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe [*] est conforme á la norme NMB-003 du Canada. RF Notices This device can contain transmitter Module(s) FCC ID: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment under 47 CFR 2.1093 paragraph (d)(2). FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. For hand-held operation only. This IPDA meets FCC RF exposure guidelines when used in hand-held. R&TTE Directive Requirements (Applies only to equipment operated within the EU/EFTA) Information to User A label on the exterior of the device should resemble one of the labels shown below (the label contains the LXE part number of the installed radio card). The labels shown below and affixed to the device, identify where the device may be used and where its use is restricted. Use of a device is prohibited in countries not listed below or otherwise identified by the label. (May or may not include the 0560 Notified Body Number. Substitute 4 digit Notified Body Number may also be applied.) E-EQ-MX9OGWW-C [ 11 ] MX9 User Guide Laser Light Safety Statement Laser Light Safety Statement Warning: This product uses laser light. One of the following labels is provided on the scanner. Please read the Caution statement. (US) Mise én garde: Ce produit utilise un rayon laser. L’une des étiquettes suivantes est apposée sur le scanneur. Veuillez lire l’avertissement qu’elle contient. (FR) Advertência: Este produto usa luz de laser. O scanner contém um dos seguintes avisos. Favor ler o Aviso. (PT) Varning: Denna produkt använder laserljus. En av de nedanstående etiketterna sitter på scannern. Var god läs varningstexten. (SE) Advarsel: Dette produkt anvender laserlys. En af følgende mærkater anvendes på scanneren. Læs venligst sikkerhedsforanstaltningen. (DK) Varoitus: Tämä tuote käyttää laservaloa. Skannerissa on jokin seuraavista tarroista. Lue Huomio-kohta. (FI) Warnung: Dieses Produkt verwendet Laserlicht. Eines der folgenden Etiketten befindet sich auf dem Scanner. Bitte lesen Sie den Gefahrenhinweis. (DE) Attenzione: Questo prodotto utilizza luce laser. Una delle etichette seguenti c’ ubicata sullo scanner. Si raccomanda di leggere con attenzione le avvertenze riportate. (IT) Advarsel: Dette utstyret bruker laserlys. En av følgende etiketter er plassert på scanneren. Les advarselen på etiketten. (NO) Advertencia: Este producto usa luz de láser. Las etiquetas se proveen en la máquina exploradora. Por favor, lea detenidamente la explicación para las precauciones. (ES) Waarschuwing: Dit product gebruikt laserlicht. Een van de volgende labels is op de scanner aangebracht. Lees a.u.b. de waarschuwing onder Oppassen. (NL) E-EQ-MX9OGWW-C [ 12 ] MX9 User Guide Laser Light Safety Statement E-EQ-MX9OGWW-C [ 13 ] MX9 User Guide Index Scanner aperture Special Purpose Keys - 38 Key Special Purpose Keys - 62 Key Battery Install Remove Battery insert and remove instruction Bottom Top WEEE Class B 10 Component Diagrams Components Back Labels Connect or Remove the Battery Pack Front Handstrap Hotswap the Main Battery Input / Output Connector Laser Light Safety Statement 12 Laser Warnings and Labels Regulatory Statements Remove Battery RF Notices 10 11 E-EQ-MX9OGWW-C Draft 01 [ 14 ] MX9 User Guide 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Create Date : 2010:02:17 08:50:55-05:00 Creator Tool : MadCap Flare V5 Modify Date : 2010:04:14 16:01:55+08:00 Metadata Date : 2010:04:14 16:01:55+08:00 Format : application/pdf Creator : LXE Title : MX9 User Guide Draft Producer : MadCap Flare V5 Document ID : uuid:9020437a-4360-4fad-bedf-6461ef3446c0 Instance ID : uuid:123be701-d4b2-4918-98d3-ab8e6857c15c Has XFA : No Page Count : 17 Author : LXEEXIF Metadata provided by EXIF.tools