Hospira 20677 PlumA + with MedNet Wireless Enabled Infuser User Manual 735 95537 002 Insert Module Installation

Download:
Mirror Download [FCC.gov]
Document ID	545432
Application ID	2bzNWhkWyVLoiqr0RjLmpQ==
Document Description	Installation Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.33kB (79106 bits)
Date Submitted	2005-05-25 00:00:00
Date Available	2005-05-25 00:00:00
Creation Date	2005-05-19 15:37:31
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2005-05-19 16:52:10
Document Title	735-95537-002_Insert Module Installation.fm
Document Creator	Pscript.dll Version 5.0
Document Author:	10127364

Installing the Hospira MedNet™ Plug ‘n Play Module List 20677
For use with Hospira Plum A+ Infusers with software version 10.3 and higher
Note: The recommended tool for this procedure is a No. 2 Phillips screwdriver.
CAUTION: Use proper ESD grounding techniques when handling components. Wear an antistatic wrist strap and
use an ESD-protected workstation. Store the PWA in an antistatic bag before placing it on any surface.
D To replace the module, proceed as follows:
1. Press [ON/OFF] to power the infuser OFF.
2. Disconnect the infuser from AC power.
CAUTION: Infuser must be powered off for at
least 2 minutes prior to removing the module.
3. Carefully place the infuser face down.
4. Using a No. 2 Phillips screwdriver, remove the two
screws from the module (one in the upper left
corner and one in the lower left corner). Refer to
Figure 1.
5. Carefully pull the module away from the infuser.
Note: When removing the module, note the
placement guides the peripheral PWA rests
between.
6. Install the replacement module in the exact reverse
order of removal using the screws and lock
washers included with the replacement module.
Refer to Figure 2.
Figure 1. Remove Screws
Note: Verify the module is placed properly between
the guides and fits correctly into the CPU PWA.
7. Connect the infuser to AC power.
8. To verify successful module replacement, power
ON the infuser and let the system perform its selftests. The screen will display an E453 Malfunction.
9. Power the infuser OFF, and then ON again.
10. If upgrading from version 12.x, The infuser is
ready for operation.
11. If upgrading from version 10.x or 11.x:
a) Enter the serial number.
a) Power the infuser OFF, and then ON again.
The infuser is ready for operation.
Figure 2. Insert Module
Hospira, Inc.
Lake Forest, IL, U.S.A
Copyright 2005
735-95537-002 (Rev. 05/05)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2005:05:19 16:52:10-07:00
Create Date                     : 2005:05:19 15:37:31-07:00
Page Count                      : 1
About                           : uuid:3f21bcfb-19b3-4cdb-b60c-af2db10803d0
Producer                        : Acrobat Distiller 6.0 (Windows)
Creation Date                   : 2005:05:19 15:37:31-07:00
Mod Date                        : 2005:05:19 16:52:10-07:00
Author                          : 10127364
Creator Tool                    : Pscript.dll Version 5.0
Metadata Date                   : 2005:05:19 16:52:10-07:00
Document ID                     : uuid:b71ada83-535d-414c-9207-5308144b3c08
Format                          : application/pdf
Title                           : 735-95537-002_Insert Module Installation.fm
Creator                         : 10127364

EXIF Metadata provided by EXIF.tools