Huawei Technologies AP505130DN Wireless LAN Access Point User Manual Product Description
Huawei Technologies Co.,Ltd Wireless LAN Access Point Product Description
Contents
User Manual-1
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2368060 |
| Application ID | HtDB8LLiq42te3D3hkcsXg== |
| Document Description | User Manual-1 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 44.38kB (554812 bits) |
| Date Submitted | 2014-08-25 00:00:00 |
| Date Available | 2014-10-01 00:00:00 |
| Creation Date | 2014-08-20 14:41:04 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2014-08-20 14:41:04 |
| Document Title | Product Description |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | Huawei Technologies Co.,Ltd. |
Huawei AP5030DN Access Points Product Description Issue 01 Date 2014-04-15 HUAWEI TECHNOLOGIES CO., LTD. Copyright © Huawei Technologies Co., Ltd. 2014. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS" without warranties, guarantees or representations of any kind, either express or implied. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied. Huawei Technologies Co., Ltd. Address: Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China Website: http://enterprise.huawei.com Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Huawei AP5030DN Access Points Product Description Contents Contents 1 Product Positioning and Characteristics................................................................................... 1 1.1 Product Positioning ....................................................................................................................................................... 1 1.2 Product Characteristics ................................................................................................................................................. 6 2 Hardware Structure....................................................................................................................... 8 2.1 AP5030DN.................................................................................................................................................................... 8 3 Product Features .......................................................................................................................... 11 3.1 WLAN Features .......................................................................................................................................................... 11 3.2 Network Features ........................................................................................................................................................ 12 3.3 QoS Features............................................................................................................................................................... 12 3.4 Security Features ........................................................................................................................................................ 13 3.5 Maintenance Features ................................................................................................................................................. 13 3.6 BYOD ......................................................................................................................................................................... 14 3.7 Locating Service ......................................................................................................................................................... 14 3.8 Spectrum Analysis ...................................................................................................................................................... 14 4 Technical Specifications ............................................................................................................ 15 4.1 Basic Specifications .................................................................................................................................................... 15 4.2 Radio Specifications ................................................................................................................................................... 16 4.3 Standards Compliance ................................................................................................................................................ 21 Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. ii Huawei AP5030DN Access Points Product Description 1 Product Positioning and Characteristics Product Positioning and Characteristics About This Chapter 1.1 Product Positioning 1.2 Product Characteristics 1.1 Product Positioning Table 1-1 Product positioning Product Model Frequency Band IEEE Standard Compliance Positioning Usage Scenario AP5030DN Dual band: IEEE 802.11a/b/g/n/a The cost-effective AP5030DN supports 3 x 3 MIMO and provides comprehensive service support capabilities. It is deployed indoors and features high reliability, high security, simple network deployment, automatic AC discovery and configuration, and real-time management and maintenance. The AP5030DN provides 802.11n/ac wireless access networks for places with simple building structure, small size, dense users, and high capacity demands, such as small and medium enterprises and branches. 2.4 GHz 5 GHz The AP5030DN can provide services simultaneously on the 2.4 GHz and 5 GHz frequency bands to support more access users. Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. The AP5030DN can be flexibly deployed and work in both fit AP and bridge mode. Huawei AP5030DN Access Points Product Description Product Model 1 Product Positioning and Characteristics Frequency Band IEEE Standard Compliance Positioning Usage Scenario Huawei AP5030DN complies with IEEE 802.11ac and can provide gigabit access for wireless users. This high capacity greatly improves user experience on wireless networks. The AP5030DN can work as a Fat AP or Fit AP and switch flexibly between the two working modes based on the network plan. When the wireless network scale is small, customers need to purchase only AP products and set the APs to work as Fat APs. As the network scale expands, tens of or hundreds of APs exist on the network. To simplify network management, customers are advised to purchase ACs to perform centralized management on the APs and set the APs to work as Fit APs. Typical networking modes are as follows: Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Huawei AP5030DN Access Points Product Description 1 Product Positioning and Characteristics Figure 1-1 Fit AP networking (AP mode) NMS Authentication system AC Switch …… AP1 STA STA AP n Residential Business users users Management channel between NMS and AC Management channel between the AC and the AP and data channel Where data flows are encapsulated with CAPWAP Channel where data flows are not encapsulated with CAPWAP In this networking, the AP functions as a fit AP and provides only data forwarding functions. The AC is responsible for user access, AP go-online, AP management, authentication, routing, security, and QoS.Huawei AC products include the AC6605, AC6005, and Access Controller Unit (ACU2). Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Huawei AP5030DN Access Points Product Description 1 Product Positioning and Characteristics Figure 1-2 Fit AP networking (WDS mode: point-to-point) Figure 1-3 Fit AP networking (WDS mode: point-to-multipoint) In this networking, the AP connects two or more independently wired or wireless LANs through wireless links to construct a network on which users can exchange data. In Wireless Distribution System (WDS) mode, the AP supports point-to-point (P2P) and point-to-multipoint (P2MP) networking modes. With 5 GHz and 2.4 GHz frequency bands, the AP can implement wireless bridging and access functions. Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Huawei AP5030DN Access Points Product Description 1 Product Positioning and Characteristics Figure 1-4 Fit AP mesh networking On the preceding network, APs function as mesh points (MPs) and are fully-meshed to establish an auto-configured and self-healing wireless mesh network (WMN). APs with the gateway function can work as the mesh portal points (MPPs) through which the WMN can provide access to the Internet. Terminals connect to APs to access the WMN. The WMN uses dedicated mesh routing protocols to guarantee high transmission quality and is more applicable to scenarios that require high bandwidth and highly stable Internet connections. Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Huawei AP5030DN Access Points Product Description 1 Product Positioning and Characteristics Figure 1-5 Fat AP networking Switch …… AP1 STA STA AP n STA STA On the preceding network, the device functions as a Fat AP to implement functions such as user access, authentication, data security, service forwarding, and QoS. 1.2 Product Characteristics The AP5030DN has the following advantages on a WLAN. Product Characteristics Description High-speed and reliable wireless access Compatibility with IEEE 802.11a/b/g/n/ac 3 x 3 MIMO and a maximum rate of 1.75 Gbit/s Link aggregation of dual Ethernet ports Supports Wi-Fi Multimedia (WMM) and priority mapping on the air interface and wired interface. Supports wired link integrity check. Supports load balancing. Supports roaming without service interruption in Fit AP mode. Supports AC dual-link backup in Fit AP mode. Latest 802.11ac chip with higher performance and wider coverage Supports airtime scheduling which ensures fairness in channel occupation time for all users. Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Huawei AP5030DN Access Points Product Description 1 Product Positioning and Characteristics Product Characteristics Description Comprehensive user access control capability Supports access control lists (ACLs) and implements user access control based on the user group policy. Provides fine-grained bandwidth management for each user. Supports user isolation policies. Supports unified authentication on the AC in Fit AP mode. Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address, user agent (UA) information in an HTTP packet, and DHCP options in Fit AP mode. The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets in Fit AP mode. Open system authentication WEP authentication/encryption WPA/WPA2-PSK authentication and encryption WPA/WPA2-802.1x authentication and encryption WAPI authentication and encryption Supports wireless intrusion detection system (WIDS) and wireless intrusion prevention system (WIPS), including rogue device detection and countermeasure, attack detection and dynamic blacklist, STA/AP blacklist and whitelist. Provides flexible networking capabilities and applies to various application scenarios. Mesh and WDS scenarios are supported only in Fit AP mode. Has strong environment adaptability. The AP can automatically select the transmission rates, channels, and transmit power to adapt to various radio environments and avoid interference in real time. Adjusts bandwidth allocation based on the user quantity and environment to improve user experience. Identifies interference sources such as baby monitors, Bluetooth devices, digital cordless phones (at 2.4 GHz frequency band only), wireless audio transmitters (at both the 2.4 GHz and 5 GHz frequency bands), wireless game controllers, and microwaves in Fit AP mode and works with eSight to locate interference sources and display spectrums. Automatically goes online and loads the configuration, and supports plug-and-play (PnP) in Fit AP mode. Supports batch upgrade. Manages APs locally on the web platform and supports HTTP or HTTPS login, configuration, and maintenance in Fat AP mode. Allows real-time monitoring on the network management system (NMS) to facilitate remote configuration and fast fault location. Supports the Link Layer Discovery Protocol (LLDP) to implement automatic link discovery and obtain the network topology. High network security Flexible networking and environment adaptability Easy device management and maintenance Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Huawei AP5030DN Access Points Product Description 2 Hardware Structure Hardware Structure About This Chapter 2.1 AP5030DN 2.1 AP5030DN Appearance Figure 2-1 shows AP5030DN appearance. The actual device appearance may be different from the following device appearance, but these differences will not affect device functions. Figure 2-1 AP5030DN appearance Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Huawei AP5030DN Access Points Product Description 2 Hardware Structure Port The following figure shows ports on the AP5030DN. Figure 2-2 AP5030DN ports As shown in Figure 2-2, each port can be described as follows: 1. Input port for 12 V DC power supply 2. Default button: restores factory settings if you hold down the button more than 3 seconds. 3. GE1: 10/100/1000M port used to connect to the wired Ethernet. 4. GE0/PoE: 10/100/1000M port used to connect to the wired Ethernet. The port can connect to a PoE power supply to provide power for APs. 5. Console port: connects to the maintenance terminal for AP configuration and management. 6. Lock port: protects the AP against theft. LED Indicators Indicator colors may vary slightly at different temperature. Type Color Status Description Default status after power-on Green Steady on The AP is just powered on and the software is not started yet. Software startup status Green Steady on after blinking once After the system is reset and starts uploading the software, the indicator blinks green once. Until the software is uploaded and started, the indicator remains steady green. Running status Green Blinking once every 2s (0.5 Hz) The system is running properly, the Ethernet connection is normal, and STAs are associated with the AP. The system enters the Uboot CLI. Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Huawei AP5030DN Access Points Product Description Type Alarm Fault Issue 01 (2014-04-15) 2 Hardware Structure Color Green Red Status Description Blinking once every 5s (0.2 Hz) The system is running properly, the Ethernet connection is normal, and no STA is associated with the AP. The system is in low power consumption state. Blinking once every 0.25s (4 Hz) The software is being upgraded. After the software is uploaded and started, the AP working in Fit AP mode requests to go online on the AC and maintains this state until it goes online successfully on the AC (before the CAPWAP link is established). The AP working in Fit AP mode fails to go online on the AC (the CAPWAP link disconnects). Steady on A fault that affects services has occurred, such as a DRAM detection failure or system software loading failure. The fault cannot be automatically rectified and must be rectified manually. Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 10 Huawei AP5030DN Access Points Product Description 3 Product Features Product Features About This Chapter 3.1 WLAN Features 3.2 Network Features 3.3 QoS Features 3.4 Security Features 3.5 Maintenance Features 3.6 BYOD 3.7 Locating Service 3.8 Spectrum Analysis 3.1 WLAN Features WLAN features supported by the AP are as follows: Compatibility with IEEE 802.11a/b/g/n/ac Maximum rate: 1.75 Gbit/s Maximum ratio combining (MRC) Space time block code (STBC) Low-density parity-check (LDPC) Maximum-likelihood detection (MLD) Data unit aggregation, including A-MPDU (Tx/Rx) and A-MSDU (Rx only) Supports 802.11 dynamic frequency selection (DFS). Short GI in 20 MHz, 40 MHz, and 80 MHz modes Priority mapping and packet scheduling based on a Wi-Fi Multimedia (WMM) profile to implement priority-based data processing and forwarding Automatic and manual rate adjustment WLAN channel management and channel rate adjustment Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 11 Huawei AP5030DN Access Points Product Description 3 Product Features For details about WLAN channel management, see the Country Code & Channel Compliance Table. Automatic channel scanning and interference avoidance Service set identifier (SSID) hiding Signal sustain technology (SST) Unscheduled automatic power save delivery (U-APSD) Control and Provisioning of Wireless Access Points (CAPWAP) in Fit AP mode Automatic login in Fit AP mode Extended Service Set (ESS) in Fit AP mode Wireless distribution system (WDS) in Fit AP mode Mesh networking in Fit AP mode Multi-user CAC 3.2 Network Features Network features supported by the AP are as follows: Compliance with IEEE 802.3u Auto-negotiation of the rate and duplex mode and automatic switchover between the Media Dependent Interface (MDI) and Media Dependent Interface Crossover (MDI-X) Compliance with IEEE 802.1q SSID-based VLAN assignment VLAN trunk on uplink Ethernet ports 4094 VLAN IDs (1-4094) and a maximum of 16 virtual APs (VAPs) for each radio AP control channel in tagged and untagged mode DHCP client, obtaining IP addresses through DHCP Tunnel data forwarding and direct data forwarding STA isolation in the same VLAN Access control lists (ACLs) Link Layer Discovery Protocol (LLDP) Uninterrupted service forwarding upon CAPWAP channel disconnection in Fit AP mode Unified authentication on the AC in Fit AP mode AC dual-link backup in Fit AP mode NAT IPv6 in Fit AP mode 3.3 QoS Features QoS features supported by the AP are as follows: Priority mapping and packet scheduling based on a Wi-Fi Multimedia (WMM) profile to implement priority-based data processing and forwarding WMM parameter management for each radio Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 12 Huawei AP5030DN Access Points Product Description 3 Product Features WMM power saving Priority mapping for upstream packets and flow-based mapping for downstream packets Queue mapping and scheduling User-based bandwidth limiting Adaptive bandwidth management (the system dynamically adjusts bandwidth based on the number of users and radio environment to improve user experience) Airtime scheduling 3.4 Security Features Security features supported by the AP are as follows: Open system authentication WEP authentication/encryption using a 64-bit, 128-bit, or 152-bit encryption key WPA/WPA2-PSK authentication and encryption (WPA/WPA2 personal edition) WPA/WPA2-802.1x authentication and encryption (WPA/WPA2 enterprise edition) WPA-WPA2 hybrid authentication WAPI authentication and encryption Supports wireless intrusion detection system (WIDS) and wireless intrusion prevention system (WIPS), including rogue device detection and countermeasure, attack detection and dynamic blacklist, STA/AP blacklist and whitelist. 802.1x authentication, MAC address authentication, and Portal authentication 3.5 Maintenance Features Maintenance features supported by the AP are as follows: Unified management and maintenance on the AC in Fit AP mode Automatic login and configuration loading, and plug-and-play (PnP) in Fit AP mode WDS zero-configuration deployment in Fit AP mode Mesh network zero-configuration deployment in Fit AP mode Batch upgrade Local AP management through the serial interface or using Telnet STelnet or SFTP: user information protection using SSH v2 Web local AP management through HTTP or HTTPS Real-time configuration monitoring and fast fault location using the NMS SNMP v1/v2/v3 System status alarm Network Time Protocol (NTP) Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 13 Huawei AP5030DN Access Points Product Description 3 Product Features 3.6 BYOD The AP supports bring your own device (BYOD) only in Fit AP mode. BYOD features supported by the AP are as follows: Identifies the device type according to the organizationally unique identifier (OUI) in the MAC address. Identifies the device type according to the user agent (UA) information in an HTTP packet. Identifies the device type according to DHCP options. The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets. 3.7 Locating Service The AP supports the locating service only in Fit AP mode. Locating service features supported by the AP are as follows: Locates tags manufactured by AeroScout or Ekahau. Locates Wi-Fi terminals. Works with eSight to locate rogue devices. 3.8 Spectrum Analysis The AP supports spectrum analysis only in Fit AP mode. Spectrum analysis features supported by the AP are as follows: Identifies interference sources such as baby monitors, Bluetooth devices, digital cordless phones (at 2.4 GHz frequency band only), wireless audio transmitters (at both the 2.4 GHz and 5 GHz frequency bands), wireless game controllers, and microwaves. Works with eSight to perform spectrum analysis on interference sources. Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 14 Huawei AP5030DN Access Points Product Description 4 Technical Specifications Technical Specifications About This Chapter 4.1 Basic Specifications 4.2 Radio Specifications 4.3 Standards Compliance 4.1 Basic Specifications Table 4-1 Basic specifications Item Description Technical specifications Power specifications Environment specifications Issue 01 (2014-04-15) Dimensions (H x W x D) 53 mm x 220 mm x 220 mm Weight 1.0 kg System memory 256 MB DDR2 32 MB flash memory DC 12 V ±10% PoE power: -48 V DC (in compliance with IEEE 802.3af/at) Power input Maximum power consumption 11.5 W Operating temperature -60 m to +1800 m: -10°C to +50°C Storage temperature -40°C to +70°C NOTE The actual maximum power consumption depends on local laws and regulations. +1800 m to +5000 m: Temperature decreases by 1°C every time the altitude increases 220 m. Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 15 Huawei AP5030DN Access Points Product Description 4 Technical Specifications Item Description Operating humidity 5% to 95% (non-condensing) Waterproof grade IP41 Atmospheric pressure 70 kPa to 106 kPa 4.2 Radio Specifications Table 4-2 Radio specifications Item Description Antenna type Built-in antenna Antenna gain 2.4G: 4dBi 5G: 5dBi Maximum number of concurrent users Fit AP mode: ≤ 256 Fat AP mode: ≤ 64 Maximum transmit power for each radio 2.4 GHz: 20 dBm 5 GHz: 17 dBm NOTE The 2.4 GHz radio does not support the 40M bandwidth in FCC regions (including America). The actual transmit power depends on local laws and regulations. You can adjust the transmit power from the maximum transmit power to 1 dBm, with a step of 1 dB. Maximum number of non-overlap ping channels 2.4 GHz 5 GHz 802.11b/g 20 MHz: 3 − 802.11n 20 MHz: 3 40 MHz: 1 Issue 01 (2014-04-15) 802.11a 20 MHz: 802.11n − 20 MHz: − 40 MHz: 802.11ac − 20MHz: 5 − 40MHz: 2 − 80MHz: 1 NOTE The table uses the number of non-overlapping channels supported by China as an example. The number of non-overlapping channels varies in different countries. For details, see the Country Code & Channels compliance status NOTICE If the AP is delivered to the USA, pay attention to the following on channel and frequency band usage. 1. The country code of the AP is fixed. 2. The frequency band ranging from 5.15 GHz to 5.25 GHz can only be used indoors. 3. High power radars working at Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 16 Huawei AP5030DN Access Points Product Description Item 4 Technical Specifications Description frequencies in the range of 5.25 GHz to 5.35 GHz, 5.47 GHz to 5.6 GHz, and 5.65 GHz to 5.725 GHz can interfere with or even damage APs working at the same frequency. 4. APs cannot work at channels in frequencies ranging from 5.6 GHz to 5.65 GHz or their overlapping channels. Channel rate supported 802.11b: 1, 2, 5.5, and 11 Mbit/s 802.11a/g: 6, 9, 12, 18, 24, 36, 48, and 54 Mbit/s 802.11n: 6.5 to 450 Mbit/s 802.11ac: 6.5 to 1300Mbit/s Receiver sensitivity Issue 01 (2014-04-15) 2.4 GHz 2.4 GHz 2.4 GHz 2.4 GHz -101 dBm @ 1 Mb/s 802.11g (non-HT20) 802.11n (HT20) 802.11n(HT40) -96 dBm @ 2 Mb/s -92 dBm @ 6 Mb/s -92 dBm @ MCS0 -90 dBm @ MCS0 -93 dBm @ 5.5 Mb/s -91 dBm @ 9 Mb/s -92 dBm @ MCS1 -90 dBm @ MCS1 -91 dBm @ 11 Mb/s -91 dBm @ 12 Mb/s -92 dBm @ MCS2 -89 dBm @ MCS2 -90 dBm @ 18 Mb/s -87 dBm @ MCS3 -85 dBm @ MCS3 -89 dBm @ 24 Mb/s -85 dBm @ MCS4 -82 dBm @ MCS4 -85 dBm @ 36 Mb/s -81 dBm @ MCS5 -78 dBm @ MCS5 -82 dBm @ 48 Mb/s -79 dBm @ MCS6 -76 dBm @ MCS6 -81 dBm @ 54 Mb/s -77 dBm @ MCS7 -75 dBm @ MCS7 -90 dBm @ MCS8 -88 dBm @ MCS8 -90 dBm @ MCS9 -88 dBm @ MCS9 -90 dBm @ MCS10 -87 dBm @ MCS10 -85 dBm @ MCS11 -83 dBm @ MCS11 -83 dBm @ MCS12 -80 dBm @ MCS12 -79 dBm @ MCS13 -76 dBm @ MCS13 -77 dBm @ MCS14 -74 dBm @ MCS14 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 17 Huawei AP5030DN Access Points Product Description Item 4 Technical Specifications Description -75 dBm @ MCS15 -73 dBm @ MCS15 -88 dBm @ MCS16 -86 dBm @ MCS16 -88 dBm @ MCS17 -86 dBm @ MCS17 -88 dBm @ MCS18 -85 dBm @ MCS18 -83 dBm @ MCS19 -81 dBm @ MCS19 -81 dBm @ MCS20 -78 dBm @ MCS20 -77 dBm @ MCS21 -74 dBm @ MCS21 -75 dBm @ MCS22 -72 dBm @ MCS22 -73 dBm @ MCS23 -71 dBm @ MCS23 5 GHz 5 GHz 5 GHz 802.11a (non-HT20) 802.11n (HT20) 802.11n (HT40) -94 dBm @ 6 Mb/s -93 dBm @ MCS0 -91 dBm @ MCS0 -93 dBm @ 9 Mb/s -93 dBm @ MCS1 -91 dBm @ MCS1 -93 dBm @ 12 Mb/s -91 dBm @ MCS2 -88 dBm @ MCS2 -92 dBm @ 18 Mb/s -86 dBm @ MCS3 -83 dBm @ MCS3 -88 dBm @ 24 Mb/s -83 dBm @ MCS4 -81 dBm @ MCS4 -85 dBm @ 36 Mb/s -78 dBm @ MCS5 -76 dBm @ MCS5 -81 dBm @ 48 Mb/s -77 dBm @ MCS6 -75 dBm @ MCS6 -79 dBm @ 54 Mb/s -76 dBm @ MCS7 -74 dBm @ MCS7 -91 dBm @ MCS8 -89 dBm @ MCS8 -91 dBm @ MCS9 -89 dBm @ MCS9 -89 dBm @ MCS10 -86 dBm @ MCS10 -84 dBm @ MCS11 -81 dBm @ MCS11 -81 dBm @ -79 dBm @ Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 18 Huawei AP5030DN Access Points Product Description Item 4 Technical Specifications Description MCS12 Issue 01 (2014-04-15) MCS12 -76 dBm @ MCS13 -74 dBm @ MCS13 -75 dBm @ MCS14 -73 dBm @ MCS14 -74 dBm @ MCS15 -72 dBm @ MCS15 -89 dBm @ MCS16 -87 dBm @ MCS16 -89 dBm @ MCS17 -87 dBm @ MCS17 -87 dBm @ MCS18 -84 dBm @ MCS18 -82 dBm @ MCS19 -79 dBm @ MCS19 -79 dBm @ MCS20 -77 dBm @ MCS20 -74 dBm @ MCS21 -72 dBm @ MCS21 -73 dBm @ MCS22 -71 dBm @ MCS22 -72 dBm @ MCS23 -70 dBm @ MCS23 5 GHz 5 GHz 5 GHz 802.11ac (VTH20) 802.11ac (VTH40) 802.11ac (VTH80) -93 dBm @ MCS0NSS1 -91 dBm @ MCS0NSS1 -89 dBm @ MCS0NSS1 -93 dBm @ MCS1NSS1 -90 dBm @ MCS1NSS1 -86 dBm @ MCS1NSS1 -91 dBm @ MCS2NSS1 -88 dBm @ MCS2NSS1 -85 dBm @ MCS2NSS1 -86 dBm @ MCS3NSS1 -84 dBm @ MCS3NSS1 -81 dBm @ MCS3NSS1 -83 dBm @ MCS4NSS1 -81 dBm @ MCS4NSS1 -78 dBm @ MCS4NSS1 -78 dBm @ MCS5NSS1 -77 dBm @ MCS5NSS1 -74 dBm @ MCS5NSS1 -77 dBm @ MCS6NSS1 -75 dBm @ MCS6NSS1 -72 dBm @ MCS6NSS1 -76 dBm @ MCS7NSS1 -74 dBm @ MCS7NSS1 -71 dBm @ MCS7NSS1 -71 dBm @ MCS8NSS1 -69 dBm @ MCS8NSS1 -67 dBm @ MCS8NSS1 -91 dBm @ -67 dBm @ -65 dBm @ Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 19 Huawei AP5030DN Access Points Product Description Item 4 Technical Specifications Description MCS0NSS2 Issue 01 (2014-04-15) MCS9NSS1 -91 dBm @ MCS1NSS2 -89 dBm @ MCS2NSS2 MCS9NSS1 -89 dBm @ MCS0NSS2 -87 dBm @ MCS0NSS2 -88 dBm @ MCS1NSS2 -84 dBm @ MCS1NSS2 -84 dBm @ MCS3NSS2 -86 dBm @ MCS2NSS2 -83 dBm @ MCS2NSS2 -81 dBm @ MCS4NSS2 -82 dBm @ MCS3NSS2 -79 dBm @ MCS3NSS2 -76 dBm @ MCS5NSS2 -79 dBm @ MCS4NSS2 -76 dBm @ MCS4NSS2 -75 dBm @ MCS6NSS2 -75 dBm @ MCS5NSS2 -72 dBm @ MCS5NSS2 -74 dBm @ MCS7NSS2 -73 dBm @ MCS6NSS2 -70 dBm @ MCS6NSS2 -69 dBm @ MCS8NSS2 -72 dBm @ MCS7NSS2 -69 dBm @ MCS7NSS2 -89 dBm @ MCS0NSS3 -66 dBm @ MCS8NSS2 -64 dBm @ MCS8NSS2 -89 dBm @ MCS1NSS3 -64 dBm @ MCS9NSS2 -62 dBm @ MCS9NSS2 -87 dBm @ MCS2NSS3 -87 dBm @ MCS0NSS3 -85 dBm @ MCS0NSS3 -82 dBm @ MCS3NSS3 -86 dBm @ MCS1NSS3 -82 dBm @ MCS1NSS3 -79 dBm @ MCS4NSS3 -84 dBm @ MCS2NSS3 -81 dBm @ MCS2NSS3 -74 dBm @ MCS5NSS3 -80 dBm @ MCS3NSS3 -77 dBm @ MCS3NSS3 -73 dBm @ MCS6NSS3 -77 dBm @ MCS4NSS3 -74 dBm @ MCS4NSS3 -72 dBm @ MCS7NSS3 -73 dBm @ MCS5NSS3 -70 dBm @ MCS5NSS3 -67 dBm @ MCS8NSS3 -71 dBm @ MCS6NSS3 -67 dBm @ MCS7NSS3 -65 dBm @ MCS9NSS3 -70 dBm @ MCS7NSS3 -61 dBm @ MCS8NSS3 -63 dBm @ MCS8NSS3 -59 dBm @ MCS9NSS3 -61 dBm @ MCS9NSS3 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 20 Huawei AP5030DN Access Points Product Description 4 Technical Specifications 4.3 Standards Compliance Safety standards UL 60950–1 CAN/CSA 22.2 No.60950-1 IEC 60950–1 EN 60950–1 GB 4943 Radio standards AP5010DN-AGN: ETSI EN 300 328 ETSI EN 301 893 FCC Part 15C: 15.247 FCC Part 15C: 15.407 RSS-210 AS/NZS 4268 AP5010SN-GN: ETSI EN 300 328 FCC Part 15C: 15.247 RSS-210 AS/NZS 4268 EMC standards EN 301 489–1 EN 301 489–17 ETSI EN 60601-1-2 FCC Part 15 ICES-003 YD/T 1312.2-2004 ITU k.20 GB 9254 GB 17625.1 AS/NZS CIPSR22 EN 55022 EN 55024 CISPR 22 CISPR 24 IEC61000-4-6 IEC61000-4-2 Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 21 Huawei AP5030DN Access Points Product Description 4 Technical Specifications IEEE standards IEEE 802.11a/b/g IEEE 802.11n IEEE 802.11ac IEEE 802.11h IEEE 802.11d IEEE 802.11e Security standards 802.11i, Wi-Fi Protected Access 2 (WPA2), and WPA 802.1X Advanced Encryption Standards (AES) and Temporal Key Integrity Protocol (TKIP) EAP Type (s) Environment standards ETSI 300 019-2-1 ETSI 300 019-2-2 ETSI 300 019-2-3 ETSI 300 019-1-1 ETSI 300 019-1-2 ETSI 300 019-1-3 CENELEC EN 62311 CENELEC EN 50385 OET65 RSS-102 FCC Part1&2 FCC KDB Directive 2002/95/EC & 2011/65/EU Regulation 1907/2006/EC Directive 2002/96/EC & 2012/19/EU EMF RoHS Reach WEEE Issue 01 (2014-04-15) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 22
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 25 Language : zh-CN Tagged PDF : Yes Title : Product Description Author : Huawei Technologies Co.,Ltd. Subject : Technical Document Creator : Microsoft® Office Word 2007 Create Date : 2014:08:20 14:41:04+08:00 Modify Date : 2014:08:20 14:41:04+08:00 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools