Humax T3 11N Wireless Roaming Router User Manual

Humax Co., Ltd. 11N Wireless Roaming Router

User Manual

InternetElectrical OutletElectrical OutletT3 RouterT3 ExtenderPCGaming Console &Media SharingPrinter SharingStorage SharingMobile PhoneModemWPSWPSWPSQuick Start GuideWireless or Wired, it's smooh and seamlessAC1200 Dual Band Smart Wi-Fi RouterQUANTUM T31. Connecting the InternetYou can connect your product to the Internet over a direct WAN or through a modem. 1-1 If you access Internet by the modem such as ADSL, VDSL, cable and FTTH, plug one end of the Ethernet cable to the Internet port of your product and the other end to the LAN port of your modem. 1-2 If you access the Internet by WAN broadband, plug the Ethernet cable to the Internet port of your product. 4. Connecting the Network Devices You can connect your network devices to the router over wired or wirelessly.Use Ethernet cables to connect your devices to the router over a wired Ethernet connection. Note: We recommend you to connect entertainment devices such as OTT, gaming console and IPTV to the Entertainment ports. The ports have the priority in transmitting multimedia data without transmission delay or interruption.LEDs on the Front PanelAfter the product is successfully registered on the network, the LEDs illuminate continuously to indicate that the product is active and fully operational.LED OperationPower White On Power is on.O Power is o.InternetWhite On Internet is connected. White Blinking Firmware update is in progress.O Internet is not connected.WirelessWhite On Network is connected wirelessly.White Slow Blinking WPS is in conguration. It may take 2 minutes.White Fast Blinking WPS conguration is failed. Blue On *Roaming & mesh network is congured through the Internet. Blue Slow Blinking *Roaming & mesh network is in conguration. It may take 2 minutes.Blue Fast Blinking *Roaming & mesh network conguration is failed.O Wi-Fi is not available. Ethernet White On Networking device is connected to the LAN port.O No device is connected to the LAN port.Internet, Wireless, Ethernet Blinking Resetting the system is in progress. Note: Blue light is turned on when the roaming & mesh network is successfully configured over HUMAX products. Internet ConnectionYou can configure the network over a wired Ethernet connection or wirelessly.Wired Connect the Ethernet cable between the PC and the LAN port of your product. Wireless 1. Open the web browser.2. Enter http://dearmyrouter.net to the address bar, and then press the Enter key.3. The default ID and password are admin and nnnn. nnnn is the last 4 digits of serial number. Refer to the serial number at the bottom of your product.Note: We recommend you to change the ID and password to secure your network. Go to Management > Change Password to change your password.Q-MODEYour product supports Q-MODE that enables operating as a router or an extender.It’s very simple to change the operation mode. Just slide the Q-MODE switch to ROUTER or EXTENDER. Then, the mode change is automatically completed.3. Powering On1. Plug in the AC power adaptor from the power connector to an electrical outlet. 2. If the power successfully turns on, a white light on the power LED is turned on.Note: Use only the AC power adaptor provided in this product. Using other adaptors may damage the product.3. Conguring WPSYou can configure WPS between the extender and the router.3-1 Press the WPS buttons on both devices within 2 minutes. When WPS is successfully configured, the blue light blinks on the Wireless LED.Note: If you use another router other than HUMAX product, the white light blinks on the Wireless LED, which means your extender is in repeater mode. 2. Powering On2. Checking the ModeYour product has the Q-MODE switch. Check that the switch is set to ROUTER. 1. Changing the ModeYour product has the Q-MODE switch. Slide the switch to EXTENDER.Warning1. Connect all devices before you plug any power cords into the electrical outlet.2. Always turn off the product and network devices before you connect or disconnect any cables.3. Hazardous electrical voltages can exist on the product and peripheral devices and can be present on any connected cables.- With HUMAX QUANTUM Series, you will experience seamless Wi-Fi network at any moment.- T1, T2, T3, T3A, X1 and X3 support both roaming & mesh network, and T5, T7 and T9 support roaming network only.- Roaming & mesh feature is configured over HUMAX products. (*)BOTH*Roaming Mode*Mesh ModeScan the QR code to access @@ on your mobile device. Use it as RouterUse it as Extender1-11-2WPSExtender has wireless connectivity with a third party router*Roaming & mesh network is configured over HUMAX productsRouter Mode WISP ModeAP ModeRepeater ModeMedia Bridge Mode3-2 Check the network when the connection is complete. If you connect the extender to a HUMAX router, both network names are the same as if they configure a single network. But, if you use a router other than HUMAX products, the network name of your extender will copy the router›s name following Ext2G or Ext5G. (ex. Router_Ext5G)Welcome to QUANTUM T3!http://dearmyrouter.net192.168.1.1admin****Password! For the default ID and password, see the bottom of the product.LoginIDROUTER EXTENDERHumax Co.,Ltd.HUMAX BLDG., 2, Yeongmun-ro,Cheoin-gu, Yongin-si, Gyeonggi-do,449-934,South KoreaTrade Name/Mark: xxxxxxFull Postal Address: xxxxxxDesigned by Humax (Korea) Made in ChinaRouter Login:http://dearmyrouter.netID: adminPassword: nnnn S/N: QT3YYWWnnnnnnMac: DCDC8321000001FCC ID: O6ZT3Model: QUANTUM T3 Code: 4-000232.4G/5G SSID: We Love You So MuchPassword: humax_nnnn211-170615D170027211BarcodePower Input: 12V 1.5A※Please change Login Password and Wi-Fi Password for Security.Humax Co.,Ltd.HUMAX BLDG., 2, Yeongmun-ro,Cheoin-gu, Yongin-si, Gyeonggi-do,449-934,South KoreaTrade Name/Mark: xxxxxxFull Postal Address: xxxxxxDesigned by Humax (Korea) Made in ChinaRouter Login:http://dearmyrouter.netID: adminPassword: nnnn S/N: QT3YYWWnnnnnnMac: DCDC8321000001FCC ID: O6ZT3Model: QUANTUM T3 Code: 4-000232.4G/5G SSID: We Love You So MuchPassword: humax_nnnn211-170615D170027211BarcodePower Input: 12V 1.5A※Please change Login Password and Wi-Fi Password for Security.
Network Conguration on Web PageWhen you log in to the router for the first time, the installation wizard will appear. Then, follow the steps to configure the network.Router Mode 1. Welcome Click Start. The system will check automatically if your router is connected to the Internet. Extender ModeSlide the Q-MODE switch to EXTENDER. T3 operates as an extender, and configures the roaming & mesh network with a HUMAX router. x T3 works automatically in AP mode if you connect it to a router over a wired Ethernet cable and use a client device wirelessly. x T3 works automatically in media bridge mode if you connect it to a router wirelessly and use a client device over a wired Ethernet cable. x T3 works automatically in repeater mode if you connect it wirelessly to a router other than a HUMAX router and use a client device wirelessly. x If T3 works together with a HUMAX router, the roaming & mesh network is configured over the products.2. Internet Setting You can connect the Internet automatically or manually depending on your Internet connection type. Note: This page appears only when your product is not connected to the Internet.3. Wireless Network SettingEnter your own network name and password to change the default settings. You can secure your wireless network from unauthorized users. 2-1. Roaming & Mesh Just press the WPS buttons on HUMAX products within 1 second. Then, they are connected each other automatically, and configure the mesh network. You will experience seamless Wi-Fi roaming over the mesh network.2-2. RepeaterIf you have a networking device other than HUMAX products, select it from the list and then enter the password. You will experience stronger and wider Wi-Fi signal. 1. Welcome If you configure the network with HUMAX products only, click HUMAX Products and go to 2-1. Roaming & Mesh. If you use a third party product other than HUMAX, click Other Products and go to 2-2 Repeater. HomeAfter completing the network settings, go to Operation Mode. In this page, you can see the current status of your product. 4. Password Setting Enter your ID and password to change the default password. You can enhance the security on your network environment. 5. SummaryWhen you complete your network settings, the information on your network will display. Select the connection type your ISP is using. In most cases, it will be Dynamic IP.• Dynamic IP: The Internet will be connected automatically. • Static IP: Enter the IP address, Subnet mask, Gateway and DNS server supplied by the ISP.• PPPoE: Enter the user name and password supplied by the ISP.• PPTP or L2TP: Enter the user name, password and VPN server supplied by the ISP. Note: For more information on the Internet connection, refer to the web manual at www.humaxdigital.com/QUANTUM.If your router is successfully connected to the Internet, the information on the internet connection will display. Note: • If you want to skip the installation wizard, click Skip. This button is available always during installation wizard. • We recommend you to update the firmware to the latest version when available.WISP ModeYou can use wireless Internet service in Router mode. 1. Log in to dearmyrouter.net, and then go to Management > WISP Mode. 2. Set the WISP mode to On, and select your Internet service provider.WPSInternet SettingYou can manually configure your connection settings. If you do not know the Internet connection type, please contact your ISP.Connection Type? What is the Dynamic IP/Static IP/PPPoE/PPTP/L2TP? view moreDynamic IP ٕPrevious NextInternet SettingConnection TypeWAN IP AddressSubnet MaskGatewayPrimary DNSSecondary DNSDynamic IP100.1.1.1255.255.255.0192.168.1.10.0.0.00.0.0.0Previous NextSummaryInternetWireless 2.4GHzWireless 5GHzConnection TypeIP AddressNetwork Name (SSID)PasswordNetwork Name (SSID)PasswordDynamic IP100.1.1.1We Love You So Muchhumax_0000 We Love You So Muchhumax_0000 Previous DoneChange Password (Optional)If you change the password, you can make your network more secure. For the default ID and password, see the bottom of the product. The changed password will be applied from the next login. Login IDCurrent PasswordNew PasswordRetype New PasswordPrevious Next admin HomeThis page shows the current status and some basic settings of the device.Operation ModeConnection StatusIP AddressSubnet MaskGatewayDNS ServerMAC AddressRouter ModeDynamic IP183.99.19.131255.255.255.128183.99.19.129168.126.63.1/168126.63.2F4:28:53:35:C3:F9InternetDynamic IP10.10.10.1QUANTUM T35G2.4GSanULTRA DUAL_1 4 DevicesWelcone to Quantum T3 !This is Quantum T3,x Complies with next generation 11ac Wi-Fi standard.x Wi-Fi 1200 Mbps - 900 + 300 Mbps speed.x Provides WEP 64/128-bit, WPA, WPA2 and WPA-Mixed security.x Supports Guest Network, Media Sharing, QoS, Parental Control, VPN, WPS etc.x Supports Roaming & Mesh for Mobile Client.x Supports Power Saving, LED Control, System Restart for energy saving.You can more easily set various functions through web UI and experience fabulous router.Do you want to start the wizard for easy setup?StartWireless Setting2.4GHz 5GHzNetwork Name (SSID) Network Name (SSID)Password PasswordCopy 2.4GHz password? About wireless security and password. view more We Love You So Much We Love You So Much Previous NextRepeater SettingSelect a device from the list below and enter the password to connect to the host device. Using the WPS button on both devices, you can easily connect them.If you want to configure the network over a wired Ethernet connection, plug the Ethernet cable into the WAN Port of the host device. In this case, the host operates automatically in Bridge mode.Network Name (SSID) CH RSSI Security MAC Address BandIPTime ZoneTIANA_89ASUSWafyaiptime11139-45-47-51-26-77WPA2-PSKWPA2-PSKWPA2-PSKNoneWPA2-PSKBC:76:70:7C:5C:74F8:D1:11:5C:84:BA70:7C:F8:D1:11:5511:5C:54:D8:33:985C:74:31:AB:C1:D22.4GHz2.4GHz2.4GHz2.4GHz5GHzPassword **********WPSNextBackOn/OffSelect the device and enter the password to connect the host device. Network Name (SSID) CH RSSI Security MAC Address BandWe Love So MuchTIANA_89ASUSWafyaNETGEARiptime111319-45-47-51-26-51-77WPA2-PSKWPA2-PSKWPA2-PSKNoneWPA2-PSKWEPBC:76:70:7C:5C:74F8:D1:11:5C:84:BA70:7C:F8:D1:11:5511:5C:54:D8:33:9870:7C:F8:D1:11:555C:74:31:AB:C1:D22.4GHz2.4GHz2.4GHz2.4GHz2.4GHz2.4GHzPassword **********ConnectBackRefreshWISP ModeIn this mode, all Ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in Ethernet ports share the same IP to ISP through wireless LAN.Roaming & Mesh SettingHUMAX each other two products that you want to connect to, you can simply Extended Network via the WPS button.Place the product on where to actual use, press the WPS button on your product. Tip! Minimizing the walls, furniture, appliances, etc. to connect between the two products, and the products work best when operating at up to 12m (40 feet) inside and outside.If the existing configured, pressing the WPS button on the Mesh Network products and add new products are the closest connection automatically.Start WPS Process...PreviousWPSWelcome to Extended NetworkYour product has changed to Extender mode. In this mode, you can expand Wi-Fi coverage.If you want to configure the network over a wired Ethernet connection, plug the Ethernet cable into the WAN port of your product. In this case, the product operates automatically in Bridge mode.Select a product you want to connect wirelessly.NextHUMAX Products Other Products

Navigation menu