Humax X1 11n Wireless Roaming Extender User Manual QG X1 100GB 16 0902 indd

Humax Co., Ltd. 11n Wireless Roaming Extender QG X1 100GB 16 0902 indd

Users Manual

WPSETHERNET2. Connecting to Router2-1 Connect your extender to a host router and press the WPS buttons of both devices within 2 minutes. Note: Press the WPS button on the extender 1 minute after turning it on. 2-2 Wait until the green or orange light on the Extended LED blinks slow. In green light, you can enjoy Wi-Fi network in an extended area.In orange light, you can experience the seamless roaming & mesh network in your home. To enjoy roaming & mesh network, you should congure the network with HUMAX products only.Note: For more information about using the WPS feature on your router, refer to the user guide of the router. 2-3 Check the network when the connection is complete. If you connect the extender to a HUMAX router, both network names are the same as if they congure a single network. But, if you use a router other than HUMAX products, the network name of your extender will copy the router›s name following Ext2G or Ext5G. (ex. Router_Ext5G)3. Relocating ExtenderPlace your extender about halfway between your router and Wi-Fi dead zone.Plug the extender into an electrical outlet and wait until the Good Range LED lights green. Note: If a green light on the Too Close or Too Far LEDs is turned on, move the extender far from or closer to the router until the Good Range LED lights green.1. Powering OnPlug in your extender to an electrical outlet and wait until a green light on the Power LED is turned on. It may take one minute.Note: We recommend that the extender be positioned near the router to get the best signal.Warning1. Connect all devices before you plug any power cords into the electrical outlet.2. Always turn o the product and network devices before you connect or disconnect any cables.3. Hazardous electrical voltages can exist on the product and peripheral devices and can be present on any connected cables.Scan the QR codeto access @@ on your mobile device.t WPS: Press the WPS button to activate the wireless protected setup.t RESET: Keep pressing the reset button for 5 seconds and release it if all LEDs are blink. t ETHERNET: Connect your smart TV, gaming console or PC. Electrical OutletElectrical OutletPC Mobile PhoneTabletQUANTUM RouterX1 ExtenderInternetQuick Start GuideWireless or Wired, it's 11n Wireless Roaming ExtenderQUANTUM X1FCC warning:user’s authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Consult the dealer or an experienced radio/TV technician for help.LEDs on the Front PanelAfter the product is successfully registered on the network, the LEDs illuminate continuously to indicate that the product is active and fully operational.noitarepODELPower .nosirewoPnOneerG.ffosirewoPffOExtendedExtenderGreen On WPS Conncetion between router and extender is in progress.Green Fast Blinking WPS Conncetion between router and extender is failed. It blinks for 2 minutes. Green Slow Blinking WPS connection between router and extender is successful. It blinks for 5 seconds.Roaming& MeshOrange On Synchronization over smart roaming & mesh network is successful.Orange Fast Blinking WPS connection between router and extender is failed. Orange Slow Blinking WPS connection between router and extender is successful.Too Close Green On Wireless network signal is strong. Move a client device far from the product.Good Range .doogsilangiskrowtensseleriWnOneerGToo Far Green On Wireless network signal is weak. Move a client device closer to the product.Extended, Too Close,Good Range, Too Far Blinking Resetting the system is in progress.Note:tOrange light is turned on when your product operates over the roaming & mesh network.tYou can turn the LEDs o if the notication is not needed. Go to Management > Energy Saving > LED .

Navigation menu