Hunter Engineering 45-1637 Hunter Model 45-1637, Automotive tire tread depth gauge User Manual CERTIFICATE OF COMPLIANCE

Hunter Engineering Company Hunter Model 45-1637, Automotive tire tread depth gauge CERTIFICATE OF COMPLIANCE

User Manual

Rhein Tech Laboratories, Inc. Client: Hunter Engineering Company 360 Herndon Parkway Model: 45-1637 Suite 1400 Standards: FCC 15.249/IC RSS-210 Herndon, VA 20170 ID’s: LS3-45-1637/2938A-451637 http://www.rheintech.com Report #: 2017285 Page 27 of 35 Appendix K: Manual Please refer to the following page.
18 GETTING STARTEDSpecific Precautions/Power SourceNorth AmericaThe PC aligner is intended to operate from a power source that will apply 120 VAC (nominal) 50/60 Hz between the supply conductors of the power cordset.Other RegionsThe PC aligner is intended to operate from a power source that will apply 230 VAC (nominal) 50/60 Hz between the supply conductors of the power cordset. The power supply cordset, supplied with this equipment, may need modification to allow connection to the power supply mains. Your Hunter service representative will install the proper plug for your location.A protective ground connection, through the grounding conductor in the power cord, is essential for safe operation. Use only a power cord that is in good condition.FUSING:To avoid fire hazard, use only the fuse specified for your product.EQUIPMENT SERVICE:This equipment contains no user serviceable parts. All repairs must be referred to a qualified Hunter Service Representative.PROVISIONS FOR LIFTING AND CARRYING:No provision has been made for lifting or carrying this equipment. The unit must be moved by rolling it on its casters.Equipment SpecificationsElectricalVOLTAGE: 120/230 volts (nominal)AMPERAGE: 6/3 ampsWATTAGE: 720 wattsAtmosphericsTEMPERATURE: +32°F to +122°F (0°C to +50°C)RELATIVE HUMIDITY: Up to 95% Non-condensingALTITUDE: Up to 10,000 ft. (3048 m)Explanation of SymbolsThese symbols appear on the equipment.This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.Tread DepthTool: 221-731-1Contains FCC ID: LS3-45-1443 IC: 2938A-451443 Model: 45-1443-OR- Contains FCC ID: LS3-45-1637 IC: 2938A-451637 Model 45-1637This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. this device may not cause harmful interference, and2. this device must accept any interference received, including interference that may cause undesired operation.This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Navigation menu