Hyundai Electronics Co HGP-230 Single Band PCS CDMA Phone User Manual
Hyundai Electronics Industries Co Ltd Single Band PCS CDMA Phone Users Manual
Users Manual
HYUNDAI PCS CELLULAR PHONE P230E USER’S MANUAL HYUNDAI ELECTRONICS INDUSTRIES., Ltd. Mobile Telecommunications Division Chapter 1 Prior to Use ➀ Names and function of each part ➁ Screen status display and function Role of the function buttons [TALK] This button is used when you make a call or receive a call. [END] This button is used when you terminate a call or exit the current menu in the menu [RCL] This button is used when you look up the list of stored phone numbers or names or the phone number you just called. [CLR] This button is used to clear the digits and/or text from the display or Memory. [STO] This button is used to go to a lower level menu or to store the set parameter; put phone number and names into memory or erase those that were input. [*][# ] These buttons are scroll buttons which you use to select screen contents. [PWR] This button is used to turn the handset on or off [MENU] This button is used to select menu. This button is used to select SMS service . Screen status display and function Signal strength The strength of current signal is displayed with the number (0-5) of bar. Roaming This icon shows the user is outside the normal service area . Service possible/impossible When you are in an area where service possible, When you are in an area where service is impossible, service, “in service icon” is displayed. displayed. is displayed. Also when you are in Voice or Character message service Blinks when character or voice messages have been received. Alarm Blinks when alarm was played if user set alarm. Balance of battery power The balance of battery power available is displayed with the number (0~4) of bar. Chapter 2 Basic operation ➀ Menu structures ➁ How to use menu function ➂ How to use handset ➃ Function in the call ● MENU STRUCTURE Menu Submenu 1: BILLING 2: SETTING 1: 2: 3: 4: AUTO AUTO AUTO DTMF RETRY ANSWER HYPHEN LENGTH 1: INTERVAL 2: REPEAT 1: SHORT 2: LONG 5: ONE TOUCH 3: DISPLAY 4: VOLUME 1: DSPLY TIME 2: BANNER 3: LCD CONTST 4 :BACK LIGHT 1: RING TYPE 2: RINGER 3: 4: 5: 6: 7: 5: CALL TIMER EARPIECE KEYPAD VOL HANDSFREE CONNECT V. MY MELODY 1: CALL TIME 2: ALARM 1: AUTO LIGHT 2: LENGTH LED LED+BACKLIGHT VIBRATOR SILENT VOLUME 1: 2: 1: 2: 3: 4: 1: 2: 3: EDIT LISTEN LAST CALL ALL CALLS HOME CALLS ROAM CALLS ACTIVATE ALARM ONLY ALARM CALL Menu Submenu 6: BIO RHYTHM 1: 2: 3: 1: 2: 3: 4: 1: 2: 3: 1: 7: ALERTS 8: PHONE INFO 9: SECURITY TODAY BIO SOMEDAY BIO BIRTHDAY MIN ALERT FADE ALERT ROAM ALERT LOW SIGNAL PHONE # PHONE VERSION EVRC MODE LOCK 2: RESTRICT 3: RESET 4: CLEAR 1: AUTO LOCK 2: CHANGE CODE. 1: 2: 3: 4: 5: 6: INCOMING OUTGOING DIAL # MEMORY ONLY LONG DIST 900# 1: 2: 3: 4: STORED #S ALARM HOME CALLS ROAM CALLS Menu RECALL MENU 1: PHONE BOOK MENU IN CALLS 1: SEND PHONE # 2: CALL LOGS 2: SCRATCH PAD 3: MUTE DIAL MENU ( DIAL BUTTON + [MENU] BUTTON) DIAL MENU IN CALLS 1:HARD PAUSE 2:TIME PAUSE 3:ONE HYPHEN 1:SEND PHONE # 2:HART PAUSE 3:TIME PAUSE 4:ONE HYPHEN How to use Menu function ♣ Please read this before you use your handset 1. In a standby screen, press [MENU] button. 2. To move around the menu, use scroll buttons. If you press the scroll button continuously, passes by automatically. the menu Scroll buttons: [*▲],[#▼],volume[+],volume[-] 3. To go back to previous screen, press [CLR] button. To exit menu screen, press [END] button. 4. To go to a lower menu, press appropriate number, or select desired item by scroll button, and then press[STO]button. If there is lower menu, the lower menu will be newly displayed. 5. [SMS],[RCL],[SEND] buttons can function be used while using menu How to use handset How to turn the handset on • Press [PWR]button until the lamp turn on ! Handset is in locking status if “Lock code” is displayed on the screen. When the lock code is displaying, enter a 4-digit lock release number to unlock the handset. then use. !The default value of lock code is “0000”.. ! If there is a lot of stored information, it takes How to turn the handset off • Press [PWR]button until the lamp turn on “REGISTERING...” message is displayed when the user presses PWR button. This message indicates that the handset is registering the power off information, and that means mobile telecommunications service system does not have to search the user. ! If the “LOW BATTERY WARNING POWER OFF” message is displayed and the power goes off, there is a possibility of damaging the memory. Therefore, in that case, do not turn the power on, and change or charge the battery immediately. ! When the power goes off when the battery is separated while it was power on status, the calling time, phone number previous call, and frequently used area code might not get stored properly. 10 How to call Press area code + phone number in order How to modify a phone number you have entered: " number by number modification: Press [CLR] button. " Whole number modification: Press [CLR] button and hold more than 0.5 second. • Press [TALK]. ! "CALL FAILED” message is displayed when the call is not connected. ! When the line is busy, press (END) button, and retry [TALK] button. ! If you select AUTO RETRY function, the call will be repeated automatically . ! It is convenient to connect the call after hearing system connection signal sounding “beep, beep, beep” . • press [END]button when end the call ! The number of calling minutes blinks for 3 seconds. Depending on the network the user is using, there can be differences but it is not related to actual service charge the user has to pay. Press any button to go back to standby status Note To go back to previous call number, press [TALK] button. If the sign shows up on the screen, the call cannot be connected, and the user should get out of the current area. 11 Phone number input method ! To call convention phone : area code + phone number+ [TALK] ! To call emergency numbers : emergency number ( 911,311,*911,#911,#311)+ [TALK] ! To call other cellular phone : area code + phone number+ [TALK] ! To call international number: international call identification number + country code + phone number + [TALK] ! To call wireless beeper:wireless beeper identification number + beeper number+ [TALK] Electronic dialing function using pause character Electronic dialing function to use ARS service provided by banks, etc, and auto beep function. 1. Enter phone number, and press [MENU]# # [1] or [2]. 0154834326P 2. Press numbers to be electronically dialed. 01548343 26P1T023449000 3. Press [TALK] button. " $ HARD PAUSE : Enter the pause character (P) after the phone number and press [TALK]number to send phone number entered after the pause character. 12 " % TIME PAUSE : If you enter the pause character (T), the phone number entered after the pause character will be send out automatically in three 1 seconds. Any button except [PWR] button when phone bell rings or lamp blinks. • To end the call, press [END] button. How to answer calls Note ! If you set AUTO ANSWER function in advance, the call will be connected after the designated number of bell rings. (Refer to P ) Sender number display function PCS service provider supports sender number display function. The service will be available after subscribing to the service. 13 When there is an incoming call, the sender’s phone number is displayed on the screen as following. Caller ID : 02 - 3 4 4 9 - 0 0 0 0 Missing message display function Displays calls that the user didn’t answered. ① Displays the number of missed calls and latest calling time. ①Adjust volume by pressing the volume button during the state of operation of the handset as below: " Call status: Ear piece volume adjustment " Standby status: Beep volume adjustment When bell rings: Ringer volume adjustment " MISSED XX CALLS status in hands-free: hands-free volume adjustment " Call 18 : 25 & If the user subscribes sender number display function service, senders’ numbers will be displayed on the screen. And the call will be stored in the previous call & The message will be cleared when the user presses [CLR]/[END] button. How to adjust volume Volume adjusting can be done in two ways: by using the volume button on the side of the receiver, or by using the buinon menu 14 ➁ After adjusting the volume, store using [STO] button. " The volume level is stored automatically2 seconds after adjusting the volume. 15 Call functions Silent pad phone number storage function In this function a beep sound is blocked from transmission to the other party when you press a new phone number to store during a call. ① Press [MENU]→ 2 during a call ② Enter the phone number you want to store. • To cancel this function, repeat the above procedure. Reference Then “SILENT PAD” message disappears. Muting function This function mutes your voice from being transmitted to the other party during a call. ① Press [MENU]→ 3 during a call. To cancel this function, repeat the above procedure. Reference Then “MUTE” message disappears. Caller number sending function This function enables the caller number to be transmitted automatically to a pager you called without pressing the whole phone number . ① Press [MENU]→➀ when you are asked to enter your number after recalling. To check current time while using the handset, press [CLR] button.. 16 Chapter 3 Memory Function ➀how to store the phone number ➁ How to use stored phone number 17 How to store a phone number You can store up to 100 frequently used phone numbers in memory. ➀ Enter the phone number you wish to store and press [STO] button Initial empty memory location number is displayed. If there is no empty memory, warning message saying “MEMORY SPACE IS FULL !“ is displayed with warning sound. If there is desired memory location number, enter the number. ➁ To store in the location number that appears in the display window, press [STO] button. If the "OVERWRITE? “ message appears after entering memory location number, that means there is another stored phone number on the location already. Select designated value using scroll button, and press [STO]• ••••. (YES) : clearing previously stored number and storing newly entered number. (NO): leaving the previously stored number. ➂ Enter the person’s name and press [STO] button. ! Select phone number hiding function using scroll button. If you select “ YES”, the number is entered as secret number. And it can be displayed only when the lock code is entered. • Press [STO]button to store. 18 How to make a call using a stored phone number One –touch /Two-touch dialing function This function lets you call stored phone number You can make a call conveniently using a stored mber without pressing [TALK] button . 0~9 : Press corresponding memory number and hold more than 1 second. 10~99 : Press first digit and second digits of the memory number short and long respectively. " If no phone number is stored, “no contents is found in the location number” is displayed on the screen. " If a phone number was stored using hiding function, the number is not displayed when originating a call. How to store a phone number 19 Reference -How to enter letter characters using dial buttons❶ Select characters you wish to enter using the dial buttons. Dial button 1 repetition 2 repetitions 3 repetitions 4 repetitions 3DEF 4GHI -- -- -- -- " When press [ -- 2ABC 9WXYZ 5 repetitions ] button change the ~ " When entering special characters such as 0!.?,-( )’ ”*#=$-+[ ], press [0] button repeatedly. The special characters will be displayed in order. ❷ Press [#• ]button to enter the next character. " Cursor moves to the next column automatically in two seconds after the selection of the character. ❸ Repeat until all the characters you want are entered. " You can store up to 16 characters. How to modify incorrectly entered characters (use [CLR] button) " For correcting one character at a time: press [CLR] button shortly or [*•]button. " For correcting the entire entry: press [CLR] button and hold more . 20 How to find the phone numbers of your latest calls The user can search up to 20 latest called numbers ➀ Press [RCL] + [1] + [1] and Locate phone numbers you want using the scroll button " [*•] scans up the phone numbers [#•] shows 1: EDIT, 2: ERASE ➁ If you want to make a call to the corresponding number, press [TALK] button. How to find a stored phone number Recalling by memory location number • Press [RCL]+[2] • Enter the memory location number If you don’t enter specific memory location number, use the scroll button to search from the first memory location number. • Search phone numbers using scroll button. " [*•] scans up the phone numbers [#•] shows 1: EDIT, 2: ERASE • Press [TALK]button if you want to call to corresponding number. Recalling by alpha Enter the alpha(or part of the alpha) ,find the phone number • Press [RCL] + [1] + [2]. • Enter the alpha (or part of the alpha) you want. After entering the alpha, press [STO]button ➂ Locate the phone number you want using the scroll button. " The first number of an entered character row is displayed. " [*•] scans up the phone numbers [#•] shows 1: EDIT, 2: ERASE ➃ Press [TALK] button if you want to call to corresponding number. 21 Recalling by number • Enter a phone number (or part of the number) you want. After entering the number, press [RCL] button. • Locate the phone number you want using the scroll buttons. " [*•] scans up the phone numbers [#•] shows 1: EDIT, 2: ERASE • Press [TALK] button if you want to call the corresponding number. • If you want erase all stored numbers refer to P58 • To clear phone number stored suing hiding function, enter the lock code. 22 Chapter 4 Convenient Functions Auto Menu function How to adjust the screen status Select bell type Current time and day display function Alert function Phone directory function 23 Auto Set Function Auto Retry interval function When a call is not connected because of too much traffic in the service system, this function retries the call automatically at a set interval. • Press [MENU] ➜ [2]➜[1] ➜[1] • Select the parameter you want using scroll button and press [STO] button " Auto answer function not used if you select BEEP sound or lamp Auto Retry times • Press [MENU] ➜ [2] ➜ [1]➜[2] • Select the parameter you want using scroll button and press [STO] button Auto answer function This function answers an incoming call automatically after a number of rings that the user sets. • Press [MENU] ➜ [2] ➜ [2] • Select the parameter you want using scroll button and press [STO]button " When the other party is busy, this function does not work. Automatic hyphen-insertion function Press [MENU] ➜ [2] ➜ [3] • Select the parameter you want using scroll button 24 and press [STO]button Auto Lighting Function This function is used in setting the day-light hours that do not need lighting. The function can be used after acquiring the system. The lighting will be on for the hours not set by the user. • Press [MENU] ➜ [3] ➜ [4]➜[1] • Select the parameter you want using scroll button and press [STO] button. • Enter the time when you selected “YES”. OFF TIME ¢ F ºROM 08 : 00 TO 17 : 00 [STO] -> OK ! Default parameters are set at 8 a.m. •5 p. m. ! To move to next item, press [STO]/[SND] button. ! The user can add or subtract number using scroll button. • To set the time, press [STO]button. DTMP speed adjusting function This function changes DTMP speed transmitted when DTMP is dialed. • Press [MENU] ➜ [2] ➜ [4] • Select the parameter you want using scroll button and press [STO] button. One Touch Dialing Select Function Select Ont-touch or Two-touch dialing function • Press [MENU] ➜ [2] ➜ [5] • Select the parameter you want using scroll button and press [STO] button. 25 Current time and day display function This function displays current time, date, and day • Press [MENU] ➜ [3] ➜ [1] • Select the designated parameter you want using scroll button and press [STO]button . Change banner function This function changes banner displayed on the screen when you turn on your handset. You can enter a banner up to 14 characters long. • Press [MENU] ➜ [3] ➜ [2] • Enter a banner and press [STO] Screen adjusting function This function adjusts the LCD screen contrast of the handset. • Press [MENU] ➜ [3] ➜ [3] • Select the contrast level you want using the scroll buttons. Ringer selection function Bell Sound Selection ① Press [MENU] ➜ [4] ➜ [1] ➜ [1] • Select the sound you want using scroll button and press [STO]button • 7 kinds of bell sounds (1~7) are available and 7 kinds of melodies (8~14) are available. 26 Vibrate Selection This function can be conveniently used by setting the beep sound function when the user is in places where it is difficult to get calls. ① Press [MENU] ➜ [4] ➜ [2] • Select the vibrate you want using scroll button and press [STO]button Select Lamp ① Press [MENU] ➜ [4] ➜ [2] • Select Lamp type you want using scroll button and press [STO]button • Support 2 kind of Lamp sound Volume Adjustment Functions 1. After pressing [MENU]-> [4], enter number(from [1] to [4] ) that corresponse to adjustment of volume(ear volume, ringer volume, key tone volume, and handsfree volume). • If the warning alarm sounds because of low battery, the sound will not be heard even if the user press the button 2. Select the level using scroll button and press [STO]button. 27 Timer Function Verification of total air time ① Press [MENU] ➜ [5] ➜ [1] ➜ [2] Verification of the last call time ① Press [MENU] ➜ [5] ➜ [1] ➜ [1] Verification of home calls ① Press [MENU] ➜ [5] ➜ [1] ➜ [3] Verification of roaming time ① Press [MENU] ➜ [5] ➜ [1] ➜ [4] Alert Function Alert during a call ① Press [MENU] ➜ [7] ➜ [1] This function sounds an alert in every minute, letting you know the call lapse time. • Select the parameter you want using scroll button and press [STO] button.. YES: sounds alert when change service area NO: sounds no alerts Alert failed service This function sounds alerts when the handset can’t make calls irregularly. ① Press [MENU] ➜ [7] ➜ [2] • Select the parameter you want. and press [STO] button 28 YES: sounds alert when calls can’t be made. NO: sounds no alert. Alert change of service This function sounds an alert and gives out a message when the handset enters a new service area, or when it enters other system service area, or when it leaves the user’s service area. ① Press [MENU] ➜ [7] ➜ [3] • Select the parameter you want using scroll button and press[STO]button YES: sounds alert and displays message when change of service NO: sounds no alert. There is 3 kind of Message CHANGING SVC ARE : when you are entering a service area different from the one you just left . LEAVING SVC AREA: when you are leaving your service area. ENTERING SVC AREA: when you are entering a new service area. Alert the low strength level of a received call This function sounds an alert when the signal of a received call is weak. ① Press [MENU] ➜ [7] ➜ [4] • Select the parameter you want using scroll button and press[STO]button YES: sounds alarm when the received call strength is weak. NO: sounds no alarm. 29 Self number check function This is a function to check the telephone number of the handset currently in use. ① Press [MENU] ➜ [8] ➜ [1] When the user press [# !] button in standby status, the handset’s phone number is displayed. Handset version check function This function checks the version of the handset currently in use. ① Press [MENU] ➜ [8] ➜ [2] EVRC mode function This function checks the version of the handset currently in use. ① Press [MENU] ➜ [8] ➜ [3] 30 Chapter 5 Security function These functions can be used by the subscriber only by entering 4 digit lock release code. The default code at the purchase is “0000”. ➊ lock function ➋ Use restricting function ➌ Contents clearing function ➍Memory Clearing function 31 Lock Function Auto Lock Function This function prevents any other person from using the handset without permission. If locked, the handset can’t be used to dial or use any other function ① Press [MENU] ➜ [9] ➜ [Lock Code] ➜ [1] ➜ [1] • Default parameter of lock code at the purchase is “0000” • Select the parameter you want using scroll button and press [ STO] button. • Lock function is ended when the 4-digit lock code is entered when the handset is in lock status • “ AFTER POWER” : lock the handset when power is cycled. • “ NOW ” : lock the handset immediately • “OFF ” : unlock the handset Note Receiving call, Emergency dialing, Hot-line dialing, Alarming function still used Lock code change This function is used when you change a 4-digit lock code, which is necessary after you release the locking status of the handset. ① Press [MENU] ➜ [9] ➜ [Lock Code] ➜ [1] ➜ [2] • Default parameter of the lock code is set to “0000” when shipped out of factory • Enter 4-digit new lock code. • Enter the lock code once again • Press [STO] 32 Use restricting function This is a function to restrict using certain functions in the handset. You can restrict five different functions independently. ① Press [MENU] ➜ [9] ➜ [Lock Code] ➜ [2] Default parameter of the lock code is set to “0000” when shipped out of factory. ② Using the scroll buttons, select the set parameter as YES. " If you set NO, this function does not advance and returns to the previous step. ③ Press [STO] button. Blocking incoming calls This is a function you can use when you do not want to answer calls. When this function is enabled, the phone does not respond to incoming calls. However, you can still make outgoing calls. ① Press Dial •[INCOMING] . ② Select the parameter you want using the scroll buttons. . RESTRICT: to refuse incoming calls. ALLOW : to accept incoming calls. ③ Press [STO] button. Blocking outgoing calls This is function allows you to prevent others from using your phone. When this function is enabled, incoming calls can be answered, but outgoing calls cannot be made. (But it is still possible to make emergency calls ). ①Press Dial •[OUTGOING] . ② Select the parameter you want using the scroll buttons. RESTRICT: to lock outgoing calls. ALLOW : to allow outgoing calls. ③ Press [STO] button. 33 Locking the dial buttons This function blocks the use of dial buttons. However when this function is enabled, you can still make calls to numbers stored in the memory. ① Press Dial •[DIAL #] . ② Select the parameter you want using the scroll buttons. . RESTRICT: to lock the use of dial buttons. ALLOW : to allow the use of dial buttons. ③ Press [STO] button. Blocking stored phone numbers This function blocks the storage of phone numbers or the use of stored phone numbers. ① Press Dial •[MEMORY ONLY]. ② Select the parameter you want using the scroll buttons. . RESTRICT: to lock the use of memory. ALLOW : to allow the use of memory. ③ Press [STO] button. If you try to use the handset when under restriction, the message THIS PHONE’S RESTRICTED is displayed with an alarm sound. 34 Memory reset function This function sets each value set in the memory into a default status when the handset is shipped out of the factory. ① Press [MENU] ➜ [9] ➜ [Lock Code] ➜ [3] Default parameter of the lock code is set to “0000” when shipped out of factory. • Select the press[STObutton. parameter using scroll button, and INITIALIZE? ¢ ºYES SEND END INITIALIZING USER MEMORY... ! If you select “YES”, following screen is displayed. And when the initialization is finished, the handset will start over. Note ' When you initialize your handset setting, following items will be changed. Auto set function Auto Retry interval ➔ 5 seconds Number of Auto Retry ➔ Three times Auto Answer ➔ off Auto Hyphen ➔ Yes Auto Lightting ➔ off Lighting length ➔ 8 seconds Key tone length ➔ short DTMF speed ➔ High speed ONE TOUCH ➔ Yes Screen setup functions Current Time and Day Display ➔ Yes Brightness of the screen ➔ 4 levels 35 Sound setup functions Answering mode ➔ 1 bell Ear Volume, Handsfree Volume➔ 6 levels Phone Bell ➔ 8 levels Key Tone ➔ 4 levels Melody ➔ Ongdalsem Melody Speed ➔ 50 Timer function Alarm setup ➔ Yes Warning function Cancel all Security functions Auto lock ➔ No Use Restriction Function➔ Yes Blocking incoming and outgoing calls, use of dial button, and use of memory ➔ Allow ' Items such as greeting, lock code, stored phone numbers, air time , alarm contents, preferred area code, and previous call contents cannot be initialized. To clear these items, except for greeting and lock code, refer to Memory Clearing Function Memory clearing function Clearing stored phone numbers This function clears all stored numbers. ① Press [MENU] ➜ [9] ➜ [Lock Code] ➜ [4] ➜ [1] Default parameter of the lock code is set to “0000” when shipped out of factory. • Select the parameter you want using scroll button and press [STO] button. Clearing alarm contents This function clears all alarm contents and reserved call information ① Press [MENU] ➜ [9] ➜ [Lock Code] ➜ [4] ➜ [2] Default parameter of the lock code is set to “0000” when shipped out of factory. • Select the parameter you want using scroll button and press [STO] button. Clearing air time in home service area This function clears air time used in home service area. 36 ① Press [MENU] ➜ [9] ➜ [Lock Code] ➜ [4] ➜ [3] Default parameter of the lock code is set to “0000” when shipped out of factory. • Select the parameter you want using scroll button and press [STO] button. Clearing air time in other service area This function clears air time used in other service area. ① Press [MENU] ➜ [9] ➜ [Lock Code] ➜ [4] ➜ [4] Default parameter of the lock code is set to “0000” when shipped out of factory. • Select the parameter you want using scroll button and press [STO] button. 37 Chapter 6 Supplementary Functions • Reserved call and alarm warning • Melody input function Reserved call and alarm warning setup function This function sounds alarm at the set time and displays alarm contents on the screen. In case of reserved call, the user can use this function after acquiring the system.. Alarm setup ① Press [MENU] ➜ [5] ➜ [2] ➜ [1] • Select the parameter you want using scroll button and press [STO]button. • When you select ”YES” at the alarm setup, sign is displayed on the screen. 38 Checking alarm warnings ① Press [MENU] ➜ [5] ➜ [2] ➜ [2] ➜ [1] • Select alarm location number using scroll button ( ALARM XX # 10/25,12:00 No Message • If there are more than 2 alarm warnings, “( #” sign is displayed ' If you set the answering status at beep or lamp mode, the handset beeps in every 2 seconds at the designated time in alarm status. 39 Entering alarm warning Alarm sound at the designated time, and the alarm sound stops when the user presses any button except the Power button or closed the cover. The alarm will sound for 1 minute. ① Press [MENU] ➜ [5] ➜ [2] ➜ [2] ➜ [2] ① Using scroll button, select the alarm location and press [ STO] button. ( ALARM XX # 14:00 Select Alarm STO -> OK • Up to 10 alarm warning can be entered. • If there are more than 2 empty alarm location, “( #” sign is displayed. ② After entering time, press [ STO]button. • Time should be entered on 24 hour basis.. (Ex: 2 p.m. #14:00) • To move to next item, press [STO]] . • You can add or subtract number using scroll button. ③ Select the parameter using acroll button When you select ONE TIME setup and press [STO] button. ! ONE TIME : The alarm sounds once at the designated time and date, and alarm contents get cleared after that. ! DAILY : The alarm sounds everyday at the same time ! When you enter the time and date, and “OVERWRITE” message is displayed on the screen, that means identical information is already reserved. ! To clear previouly reserved time and set the new time, press [STO] button. ! To leave previously reserved time, select “NO” or press [END] button. - ALARM 01 10/25,15:00 Month ? STO -> OK ! Enter the date ! Press [STO] button. ③ Select the parameter and press MESSAGE ? SEND END [STO] button. ' For character input, refer to P . 40 Alarm location Current time Checking alarm Call ① Press [MENU] ➜ [5] ➜ [2] ➜ [3] ➜ [1] Checking reserved call contens. ALARM CALL 10/25,12:00 No Message 02–3449–0000 Entering call reservation ① Press [MENU] ➜ [5] ➜ [2] ➜ [3] ➜ [2] ② The input method for time, date, and message is identical to that of alarm warning input.. ③ Entering phone number. CALL NO ? • Press [STO] button to store. 'To clear entered alarm warning and call reservation, refer to P . 41 Melody setup function This function allows user to setup the user’s favorite melody as an answering bell sound. Entering melody ① Press [MENU] ➜ [4] ➜ [7] ➜ [1] • Press [STO]button after entering melody. ' When the user press [RCL] button, previously entered melody is played with musical note displayed on the screen. ' To end the melody, press [END] button. ' The user can edit previously entered melody. ' If there is no entered melody, Ongdalsem is played. •Press [STO]/[TALK] button after entering melody speed. ' Speed : 0 ~ 99 ' Default value at the purchase : 50 • Press [STO] button after entering the title of the melody. ' If there is previously entered melody, “OVERWRITE” is displayed. ' Select the parameter you want. ' Entered melody is added to the bell sound list.( Refer to P ) Listening to the melody • Press [MENU] ➜ [4] ➜ [7] ➜ [1] • The title of melody is displayed and melody gets NAME OF MELODY played. ' The melody gets replayed when pressing [RCL] button. ' Press [END] button to stop the melody. XXXXX ' If there is no entered message, Ondalsem will be played. 42 Melody speed adjustment • Press [MENU] ➜ [4] ➜ [7] ➜ [1] • Current speed of entered melody is displayed.. Enter new speed value and press [STO] button. . MELODY TEMPO ? XX SEND END To enter melody 1. When you press dial button ) to • , a quarter note is displayed. ' The dial button $, %, *, +, ,, -, ., /, 0, and ) corresponds to musical note do, re, mi, fa, sol, ra, ti, do, high scale do, re, and mi respectively. 2. Select the length of tone by pressing [*▲] button in sequence while the quarter note is displayed. 3. When you press [ #▼ ] button, ‘#” sign is displayed under the musical note and half note is setup. 4. To enter a pause, press [*▲] button in sequence after pressing (1 ) button, and select the length of a pause. 5. It is possible to move and edit around musical notes by pressing volume buttons[-]/[+]. 6. To add musical note while you edit, hold [ 1 ] button and enter the note. 7. To erase the note, press [CLR] button. 8. When you press [RCL] button while you entering, entered melody is played. And when you press [END] button, the melody will stop. 9. When you enter 11 notes, the screen moves to the next screen. ' You can enter up to 100 notes. 43 Chapter 7 Short Message Service Function This chapter describes convenient function that allows you to send or receive a simple character message with the handset and that also allows you to check a voice message left in a voice mail service center. • Receiving a message • Checking received message 44 Short Message Service Function This chapter describes convenient function that allows you to send or receive a simple character message with the handset and that also allows you to check a voice message left in a voice mail service center. Receiving a message Character Message When the handset receives a character message, and NEW VOICE MAIL MESSAGES Pm 05:42 blinks on the screen, the following message is displayed: ' A message arrival is announced with ringer, lamp, or vibration as selected by the user. A received character message can be up to 30 characters long. Voice Message When a voice message is received, the handset Blink and displays the following message MESSAGE! Pm 05:42 45 To Check the Received Message • Press button. "1: In Message 2: Erase All •Press the dial button ①“In Meassage”. New Message O O Voice O O Character . [Voice*] [TEXT#] The unchecked character and voice messages are displayed on the screen. Character Message • Press the character ( button). The message list is displayed in order of 1 Let’s meet XX. 2 I love you. 3 it’s a long time. receipt. Unchecked messages are indicated by numbers with reversed shadow. • Select the message number you want to check by using the scroll 00 / 00 A.M. 00 : 00 ¢ Ï011-345-6789 buttons + [STO] After a period of time, the next screen will automatically be displayed (auto scroll) It is possible to confirm the displayed message by using the auto scroll or volume button. 46 Most recently received message Reference If during the check you want to call the person who sent the message, press [SEND] button. To delete a message, press [CLR] button. To return to the previous screen, press [END] button. Checking the received message Voice message • Press voice ( button). 00/00 A.M. 00 : 00 ¢ Ï011-345-6789 A voice message can only be checked; it cannot be stored in the message list. • Press [END] button. 47
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:06:26 17:21:11 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:06:26 17:21:12-04:00 Page Count : 47EXIF Metadata provided by EXIF.tools