Hyundai IBT L17C0D080 17 inch LCD Monitor User Manual

Hyundai IBT Corp. 17 inch LCD Monitor Users Manual

Users Manual

ImageQuest L70ATFT LCD Color MonitorUser's GuideClickwww.imageQuest.co.krNEXT
U.S.A.U.S.FEDERAL COMMUNICATIONS COMMISSIONRADIO FREQUENCY INTERFERENCE STATEMENTINFORMATION TO THE USERNOTE : This equipment has been tested and found to comply with the limits for aClass B digital device pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmfulinterference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet of a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for assistance.Changes or modification not expressly approved by the party responsible forcompliance could void the user's authority to operate the equipment.Connecting of peripherals requires the use of grounded shielded signal cables.BACKNEXT
WE ImageQuest CO., LTD.Ami-ri Bubal-Eub Ichon-Si Kyungki-Do467-860 KOREAdeclare under our sole responsibility that the product:to which this declaration relates is in conformity with thefollowing standard(s) or other normative document(s)following the provisions of the Low Voltage Directive 73/23/EEC,93/68/EEC and the EMC Directive 89/336/EEC.KOREA / HONG KI, KIM(Place and date of issue) (Name and signature of authorized person)DECLARATION OF CONFORMITY BACKNEXTKind of equipment : COLOR MONITORType-Designation : L17C0D080Safety : EN 60950 : 1992 + A1, A2, A3, A4, A11EMC : EN 55022 : 1998, EN 55024 : 1998EN 61000-3-2 : 1995+A1 : 1998+A2 : 1998EN 61000-3-3 : 1995Accredited testlaboratory:TÜV RheinlandAm Grauen Stein51105 Köln2001
L70A17" TFT LCD Color MonitorBACKNEXTContents4. Adjusting the picture ..................12/224-1. Using the On Screen Display ...........14/224-2. Direct access buttons .......................14/224-3. OSD Adjustments .............................15/225. Display power management ......18/22Reducing power consumption ..............18/226. Troubleshooting ..........................19/227. Specifications ..............................22/221. Introduction ...................................1/222. Safety Information ........................1/223. Installing the monitor ...................4/223-1. Packing List .........................................4/223-2. Selecting a suitable location ..............5/223-3. Connecting the monitor .....................5/22USB Hub ..............................................9/223-4. Setting the refresh rate ......................8/22Preset Timing Table ............................9/223-5. VESA MOUNTING ..............................10/22
L70A17" TFT LCD Color Monitor1. Introduction2. Safety Information1/22BACKNEXTThis manual contains instructions for installing and operating ImageQuest L70A.ImageQuest L70A is a highly ergonomic color display unit.• 17" viewable SXGA LCD• High quality screen re-scaling capability• Real ColorTM fleshtone adjustment and digital color control with innovativecolor management.• 100-240V AC input voltage / 12V (3.75A) Power adapter.• VESA DPMS (Display Power Management Signalling)• VESA DDC1/2B compatibility• Advanced digital On-Screen-Display controls• Digital signal input by DVI-1.0 compatibility • Fast and accurate auto adjustment • Most advanced image scaling• Supporting VESA Flat Panel Monitor Physical Mounting Interface• USB (Universal Serial Bus) hub, Bus-Power mode hubThis Monitor has been engineered and manufactured to assure your safety. You can prevent serious electrical shock and other hazards by keeping in mind the following:Do not place anything wet on the monitor or the powercord. Never cover the ventilation openings with anymaterial and never touch them with metallic or inflammable materials.
L70A17" TFT LCD Color Monitor2/22BACKNEXTAvoid operating the monitor in extreme heat, humidity or areas affected by dust. Temperature : 5~35°CHumidity : 30~80RH Be sure to turn the monitor off before plugging thepower cord into the socket. Make sure that the powercord and the other cords are securely and rightlyconnected.Overloaded AC outlets and extension cords are dangerous, as are frayed power cords and broken plugs, which may cause electric shock or fire. Call your service technician for replacement.Do not use sharp tools such as a pin or a pencil near the monitor, as they may scratch the LCD surface.Do not use a solvent, such as benzene, to clean the monitor, as it will damage the LCD surface.
L70A17" TFT LCD Color MonitorCleaning and Maintenance • To avoid risk of electric shock, do not disassemble the display unit cabinet. Theunit is not user-serviceable. Remember to unplug the display unit from thepower outlet before cleaning.• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do notuse thinner or benzene, abrasive cleaners or compressed air.• Do not wipe the screen with a cloth or sponge that could scratch the surface.• To clean your antistatic screen, use water and a special microfiber screencleaning tissue used in optical lens cleaning, or lightly dampen a soft, cleancloth with water or a mild detergent.• If the instructions above do not help in removing stains, contact an authorizedservice agent. 3/22BACKNEXT
L70A17" TFT LCD Color Monitor4/22BACKNEXTThe following items should be found in the packaging.Above power cord can be changed upon different voltage areas. Pleasecontact your dealer if anything is missing or damaged.Other power cord except the cord packed in the product or longer than 3mmay affect EMC of the product in operating condition.3. Installing the monitor3-1. Packing List!UKAmerican/CanadaJapanAustraliaKoreaEuropeSouth AfricaPower CordSignal CableDVI-D Cable(Option)USB CableAC/DC Power adapter Compact Disc
L70A17" TFT LCD Color Monitor5/22BACKNEXT3-2. Selecting a suitablelocation3-3. Connecting the monitor• Place the monitor at least 30cm from other electrical or heat-emittingequipment and allow at least 10cm on each side for ventilation.• Place the monitor in a position where no light shines directly onto or isreflected on the screen.• To reduce eye strain, avoid installing the display unit against a brightbackground such as a window.• Position the monitor so that the top of the screen is no higher than eye level.• Position the monitor directly in front of you at a comfortable reading distance(around 45 to 90cm) Before you start cabling your monitor, check that thepower is off on all units. To avoid any possibility ofelectric shock, always connect your equipment toproperly earthed outlets.1. Insert the other 15-pin /DVI-D signal cable connector into the 15-pin VGA/DVI-Dconnection on your computer and screw it down. 2. Plug the power cord connection to connection on the AC-DC Power adapter.3. Plug the jack of the AC-DC Power adapter connection to connection on monitor.4. Plug the other end of the power cord to your computer's main supply or to a100V-240V earthed electrical outlet.5. Turn on the monitor using the power switch and check that the power LED ison. If not, repeat steps 1,2,3 and 4 or refer to the Troubleshooting section ofthis guide.!!
L70A17" TFT LCD Color Monitor6/22BACKNEXT6. Turn on the power to the computer. The picture will appear within about 10seconds. Adjust the picture to obtain optimum picture quality. See sectionAdjusting the picture in this guide for more information.15 pin D-sub cable (Analog RGB)DVI-D cable (Digital TMDS)
L70A17" TFT LCD Color MonitorUSB hub The USB hub(Bus-powerd mode hub) have 1 upstream port and 2 downstreamports. The upstream port can be connected to the root hub of host PC or otherdownstream port. Two(2) downstream ports allow to connect another USB devicesuch as USB mouse, joystick, printer etc.1) The maximum supply current of downstream port is 100mA each when bus-powered mode hub.2) To activate the USB hub, your host system should have USB capability.7/22BACKNEXTUSB 2 downstream ports
L70A17" TFT LCD Color Monitor8/22BACKNEXT3-4. Setting the refreshrate Follow the instructions below to set your refresh rate in Windows 98.1. Go to the configuration window(Start-Settings-Configuration window).2. Double click on the ‘Display’ icon.3. Click on the ‘Settings’ tab.4. Click on the ‘Advanced’ button.5. Click on ‘Adapter’ and select 60Hz from the list.6. Click on ‘Apply’ to accept the selected value.LED Indicator Soft Power Switch
L70A17" TFT LCD Color MonitorNo.1234567891011121314Resolution720 x 400720 x 480640 x 480 800 x 600800 x 600800 x 600800 x 600832 x 6241024 x 7681024 x 7681024 x 7681152 x 8701280 x 10241280 x 1024Horizontal Frequency31.5 KHz31.5 KHz37.5 KHz35.2 KHz37.9 KHz48.1 KHz46.9 KHz49.7 KHz48.4 KHz56.5 KHz60.0 KHz68.7 KHz63.9 KHz80.0 KHzRefresh rate70 Hz70 Hz75 Hz56 Hz60 Hz72 Hz75 Hz75 Hz60 Hz70 Hz75 Hz75 Hz60 Hz75 HzPreset Timing Table If the signal from the system doesn't equal to the preset timing mode, adjustthe mode with reference to the user guide of videocard because the screenmay not be displayed.The recommended setting is a resolution of 1280x1024 and a refresh rate of 60Hz.9/21BACKNEXT!ANALOG R.G.B INPUT
L70A17" TFT LCD Color Monitor3-5. VESA MOUNTING • This display unit supports VESA FPMPMI standard for 100mmx100mm screwmounting by giving 4 screw holes inside the base stand of the unit. The basestand shall be removed before connecting to Specialty Flat Panel MonitorMounting Device.• For buying VESA Flat Panel Monitor Mounting Devices, please contactfollowing information.* Ergotron, Inc.· Address : Ergotron Europe Kuiperbergweg 50 1101 AG Amsterdam The Netherlands· Tel : +31 20 696 60 65 · Fax : +31 20 609 04 59 · E-mail : info.eu@ergotron.com10/22BACKNEXTDIGITAL R.G.B INPUTNo.1234Resolution640 x 480800 x 6001024 x 7681280 x 1024Horizontal Frequency31.5 KHz37.9 KHz48.4 KHz63.9 KHzRefresh rate60 Hz60 Hz60 Hz60 Hz
L70A17" TFT LCD Color Monitor11/22BACKNEXTDesk MountWall Mount
L70A17" TFT LCD Color Monitor4. Adjusting the picture12/22BACKNEXTYou can adjust the screen display by using the buttons located below thescreen.1280X1024V:60.0/H:63.9BRIGHTNESSIn case of applying Analog RGBInput
L70A17" TFT LCD Color Monitor13/22BACKNEXT1280X1024V:60.0/H:63.9BRIGHTNESSIn case of applying Digital TMDS Input
L70A17" TFT LCD Color Monitor14/22BACKNEXT1. Push the MENU button to call the OSD to the screen. The resolution andfrequency are displayed at the top of the menu box for your information.2. Push the or button to choose the item you want to adjust. The selecteditem is highlighted.3. Push the SELECT button to adjust the highlighted item. 4. Use the or button to adjust the selection.5. Push the MENU button to return to the previous menu if you are in a submenu.6. The display unit automatically saves the new settings in 1 second after yourlast adjustments and the menu disappears. You can also push the MENU buttonto make the menu disappear.AUTO ADJUSTAt first display a full screen such as Window's back ground.Push the button SELECT(AUTO) to adjust the shape of screenautomatically.INPUT SELECTPush the button to choose the input select adjustment afterchoosing one of Analog Signal or Digital Signal.LED Indicator will be displyed with Amber on processing.4-1. Using the On ScreenDisplay 4-2. Direct access buttons
L70A17" TFT LCD Color Monitor15/22BACKNEXT4-3. OSD AdjustmentsYou can play the moviefile to see how to adjustthe picture image byclicking each icon or titlehereunder.The OSD adjustments available to you are listed below.BRIGHTNESSAdjust the brightness of the screen.CONTRASTAdjust the contrast of the screen.COLOR CONTROLColor temperature affects the tint of the image. With lower color temperatures the image turns reddish and with higher temperatures bluish.There are three color settings available: Mode 1(a cool white), Mode 2(awarm white) or USER. With the USER setting you can set individual valuesfor red, green and blue.YUV COLORIn particular, color technology allows users to make the following coloradjustment.HUEAdjust the hue of the video image.FLESH TONEAdjust the flesh Tone of the video image.
L70A17" TFT LCD Color Monitor16/22BACKNEXTMISCELLANEOUSRECALL Recall the saved color data.OSD TIMERYou can set the displayed time of OSD Menu window on the screen byusing this adjustment.OSD POSITIONAdjust the OSD menu's horizontal or vertical position on the screen.AUTO ADJUSTYou can adjust the shape of screen automatically at the full screenpattern.LANGUAGEYou can select the language in which adjustment menus are displayed. The following languages are available: English, French, German, Italian and Spanish.H/V POSITIONH-POSITIONAdjusts the horizontal position of the entire screen image.V-POSITIONAdjusts the vertical position of the entire screen image.
L70A17" TFT LCD Color Monitor17/22BACKNEXTCLOCK PHASEPHASEAdjust the noise of the screen image.CLOCKAdjust the horizontal size of the entire screen image.INPUT SELECTThis menu used to choose the desired input signal source.There are two available signal source.• Analog R.G.B : 15 pin D-sub, Analog Signal• Digital TMDS : 24 pin DVI-D, Digital SignalIn case of applying Digital TMDS Input, the functions of Color Control, AutoAdjust, H/V Position, Clock Phase are not supported.!
L70A17" TFT LCD Color MonitorIf the power management function of your computer is enabled, your monitorturns on and off automatically. You can control power management features fromyour computer.Your computer may have power management features which enable the computeror monitor to enter a power saving mode when the system is idle. You canreactivate the system by pressing any key or moving the mouse.The power button does not disconnect the monitor from the mains. The onlyway to isolate the monitor completely from the mains supply is to unplug themains cable.18/22BACKNEXT5. Display power managementReducing powerconsumptionPower consumption45 W5 W0 WModeNormaloffUnpluggedLEDGreenOrangeNot illuminated!
L70A17" TFT LCD Color Monitor6. Troubleshooting19/22BACKNEXTProblemBlank screenError message:Video mode notsupportedThe display does not enter power managementmodePossible solutionIf the power LED is not lit, push the Soft power switch or check theAC cord to turn the monitor on. If the display unit is poweredthrough the computer, check that the computer is switched on.The display unit might be in standby mode. Push one of thekeyboard keys. Check that the keyboard is properly connected tothe computer.Check that the signal cable connector is properly connected and thatthe connection pins are not bent or damaged. If the connector isloose, tighten the connector's screws.Check that the power cable is correctly connected to the display unitand to the power outlet. Check the resolution and the frequency on the video port of yourcomputer.Compare these values with the data in the Preset Timing Table.The video signal from the computer does not comply with VESADPMS standard. Either the computer or the graphics adapter is notusing the VESA DPMS power management function.If your monitor is not functioning properly, you may be able to solve the problemby reading followings.
L70A17" TFT LCD Color Monitor20/22BACKNEXTPossible solutionCheck that the signal cable connector is properly connected and thatthe connection pins are not bent or damaged. Try another colortemperature. Adjust the picture characteristics as described in the section OSDAdjustment(4-3).A problem with your graphics adapter or display unit. Contact yourservice representative.Check that the display resolution and frequency from your PC orgraphic adapter is an available mode for your monitor.In your PC, you can check through Control panel, Display, Settings.If the setting is not correct, use your computer utility program tochange the display settings.Check that the signal cabel connector is properly connected and thatthe connection pins are not bent or damaged.If the connector is loose, tighten the connector’s screws.Check that the computer is switched on.To enter a power saving mode. You can reactivate the system bypressing any key or moving the mouse.ProblemColor defectsSize, position,shape or qualityunsatisfactoryDuplicatedimagesImage is notstableMessage : No signalThe power LED is aorange color
Possible solutionLED Indicator can be orange color on changing of video mode orInput Signal(D-sub/DVI).Check the Resolution and the frequency on the video part of yourcomputer. Compare these values with the data in the Preset TimingTable.ProblemThe power LED is aorange colorL70A17" TFT LCD Color Monitor21/22BACKNEXTContacting service If the above troubleshooting hints do not help you find a solution to the problem,contact an authorized service agent. If the monitor is sent for service, use theoriginal package if possible.Unplug the display unit from the power outlet and contact a service agent when:• The monitor does not operate normally according to the operating instructions.• The monitor exhibits a distinct change in performance.• The monitor has been dropped or the cabinet has been damaged.• The monitor has been exposed to rain, or water or liquid has been spilled ontothe monitor.
L70A17" TFT LCD Color Monitor22/22BACK17"viewable, Diagonal, Pixel pitch 0.26 mm, AM-TFT 25msec, 250cd/m225msec337.92 X 270.336 mm16,2 million colorsR.G.B Analog, Digital TMDS(DVI-D),Horizontal : 31.0 to 80.0KHz, Vertical : 56 to 75Hz135 MHzAnalog RGB : 1280X1024@75HzDigital TMDS : 1280X1024@60Hz1280X1024@60HzDC 12V 3.75A45WVESA DPMSVESA DDC 1/2BBRIGHTNESS, CONTRAST, COLOR CONTROL, YUV COLOR, MISCELLANEOUS, AUTO ADJUST, LANGUAGE, H./V. POSITION, CLOCK-PHASE, INPUT SELECT1up X 2down (Bus-Powered Hub)100 mm X 100 mm screw mountingTCO, FCC Class B, CE,cULus, TÜV-GS, SEMKO5 ~ 35O C6.7Kg unpacked, 8.7Kg packed420 X 437 X 220 mmLCDBrightnessResponse TimeDisplay areaNumber of colorInput signalsFrequency rateMaximum bandwidthMaximum resolutionRecommanded resolutionInput voltagePower consumptionPower managementPlug & PlayOSD menuUSBVESA FPMPMIErgonomics,Safety and EMCOperating TemperatureWeightDimensions (W X H X D mm)• Specification is subject to change without notice for performance improvement.7. Specifications

Navigation menu