ICOM orporated 277602 UHF Transceivers User Manual IC F3011 F3013 F4011 F4013 Instruction Manual

ICOM Incorporated UHF Transceivers IC F3011 F3013 F4011 F4013 Instruction Manual

UserManual.wiki >

ICOM orporated >

277602 User Manual >

Contents

User Manual

INSTRUCTION MANUALThis device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful inter-ference.UHF TRANSCEIVERSiF4011iF4013VHF TRANSCEIVERSiF3011iF3013

iW AR N IN GYour Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classiﬁed as “Occupational Use Only”, meaning it must be used only during the course of employment by indi-viduals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment.This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: • FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. • American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Fre-quency Electromagnetic Fields, 3 kHz to 300 GHz. • American National Standards Institute (C95.3-1992), IEEE Recom-mended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave. • The following accessories are authorized for use with this product. Use of accessories other than those speciﬁed may result in RF ex-posure levels exceeding the FCC requirements for wireless RF ex-posure.; Belt Clip (MB-94), Rechargeable Li-Ion Battery Pack (BP-230N/BP-232N) and Speaker-microphone (HM-131L).C AU T IO NTo ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occu-pational use, always adhere to the following guide-lines:SAFETY TRAINING INFORMATION

SAFETY TRAINING INFORMATION • DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna speciﬁcally authorized by the manufacturer for use with this radio. • DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). “50% duty cycle” is also applicable to VOX/PTT mode. Transmitting more than 50% of the time can cause FCC RF expo-sure compliance requirements to be exceeded. The radio is trans-mitting when the “LED indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch or VOX function. • ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clip which is listed on page 33 when attaching the radio to your belt, etc., to en-sure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound qual-ity, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side.The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-sure that this radio operates with the FCC RF exposure limits of this radio.Electromagnetic Interference/CompatibilityDuring transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electro-magnetic radiation such as hospitals, aircraft, and blasting sites.Occupational/Controlled UseThe radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.ii

ivR CAUTION! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 in.) away from the lips and the transceiver is vertical.R CAUTION! NEVER operate the transceiver with a headset or other audio accessories at high volume levels.R CAUTION! NEVER short the terminals of the battery pack.R CAUTION! NEVER use non-Icom battery packs/chargers to prevent the loss of the transceiver’s good performance and warranty.R CAUTION! NEVER expose the transceiver to rain, snow or any liquids. The transceiver may be damaged.DO NOT push [PTT] when not actually desiring to transmit.DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below –30°C (+22°F) or above +60°C (+140°F).DO NOT modify the transceiver. The transceiver warranty does not cover any problems caused by unauthorized modiﬁcation.MAKE SURE the ﬂexible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver.The use of non-Icom battery packs/chargers may impair trans-ceiver performance and invalidate the warranty.For U.S.A. onlyCAUTION! Changes or modiﬁcations to this device, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations.PRECAUTIONS

TABLE OF CONTENTSSAFETY TRAINING INFORMATION .................................................... iFOREWORD .......................................................................................iiiEXPLICIT DEFINITIONS .....................................................................iiiPRECAUTIONS .................................................................................. ivTABLE OF CONTENTS ....................................................................... v1 ACCESSORIES ......................................................................... 1–5 ■ Supplied accessories .................................................................. 1 ■ Accessory attachments .............................................................. 22 PANEL DESCRIPTION ............................................................ 6–11 ■ Front, top and side panels .......................................................... 6 ■ LED indicator .............................................................................. 8 ■ Programmable function keys ......................................................93 CONVENTIONAL OPERATION ............................................. 12–15 ■ Turning power ON ..................................................................... 12 ■ Channel selection ..................................................................... 12 ■ Receiving and transmitting ....................................................... 13 ■ Setting the squelch level ........................................................... 154 SIGNALING OPERATIONS ................................................... 16–17 ■ Call procedure .......................................................................... 16 ■ Emergency Call ........................................................................ 17 ■ DTMF transmission ................................................................... 175 BATTERY CHARGING .......................................................... 18–25 ■ Caution ..................................................................................... 18 ■ Battery chargers ....................................................................... 216 BATTERY CASE .................................................................... 26–27 ■ Optional battery case (BP-240) ................................................ 267 SWIVEL BELT CLIP .............................................................. 28–31 ■ MB-93 contents......................................................................... 28 ■ To attach ................................................................................... 28 ■ To detach .................................................................................. 308 OPTIONS ............................................................................... 32–359 FCC INFORMATION .................................................................... 36

11ACCESSORIES■ Supplied accessoriesThe following accessories are supplied.Flexibleantenna*Battery pack Battery carger(with AC adapter)Belt clip Jack cover (with screws)*This illustration is described with the VHF type.1234567891011121314151617181920

21ACCESSORIES■ Accessory attachmentsD Flexible antennaConnect the supplied ﬂexible antenna to the antenna connector.CAUTION:• NEVER HOLD the antenna when carrying the transceiver.• Transmitting without an antenna may damage the transceiver.

31ACCESSORIESD Battery packTo attach the battery pack:Slide the battery pack on the back of the transceiver in the direction of the arrow (q), then lock it with the battery release button.• Slide the battery pack until the battery release button makes a ‘click’ sound.To release the battery pack:Push the battery release button in the direction of the arrow (w) as shown below. The battery pack is then released.NEVER release or attach the battery pack when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver/battery pack and may result in the transceiver being damaged.qwBattery releasebutton1234567891011121314151617181920

41ACCESSORIESD Jack cover Attach the jack cover when the optional speaker-microphone is not used.To attach the jack cover:q Attach the jack cover to the [SP MIC] connector.w Tighten the screws.To detach the jack cover:e Unscrew the screws with a phillips screwdriver.r Detach the jack cover for the optional equipment connec-tion.eerwwq

51ACCESSORIESD Belt clipTo attach the belt clip:q Release the battery pack if it is attached.w Slide the belt clip in the direction of the arrow until the belt clip is locked and makes a ‘click’ sound.To detach the belt clip:q Release the battery pack if it is attached.w Pinch the clip (q), and slide the belt clip in the direction of the arrow (w).qw1234567891011121314151617181920

62PANEL DESCRIPTION■ Front, top and side panelsMicrophoneSpeakerrweyuitqq CHANNEL SELECTOR Rotate the channel selector to select the pre-programmed mem-ory channels.w VOLUME CONTROL [VOL] Rotate to turn the power ON/OFF and adjust the audio level.

72PANEL DESCRIPTIONe LED INDICATOR (p. 8) ➥ Lights red while transmitting. ➥ Lights green while receiving a signal, or when the squelch is open. ➥ Lights/blinks orange when the matched 2/5-tone code is re-ceived, according to the pre-programming. (For IC-F3013/F4013 only)r SPEAKER-MICROPHONE CONNECTOR [SP MIC] Connects the optional speaker-microphone, earphone, etc.[SP MIC] jack coverNOTE: Attach the [SP MIC] jack cover when the optional equip-ment is not used. (p. 4) t DEALER-PROGRAMMABLE KEY [Lower] The desired function can be assigned by your dealer. (p. 9)y PTT SWITCH [PTT]Push and hold to transmit; release to receive.u DEALER-PROGRAMMABLE KEY [Upper] The desired function can be assigned by your dealer. (p. 9)i ANTENNA CONNECTOR Connects the supplied antenna.1234567891011121314151617181920

82PANEL DESCRIPTION■ LED indicatorThe LED indicator indicates several information as follows;(Ref.; R=Red, G=Green, O=Orange) R R R R G G G G G GG G G G G G G G R G R G R G R G R G R G R G R GR O R O R O R O R O R O R O R O G G G Clone ErrClone TX/RXLow BATT1Low BATT2BusyF/S ScanO O O O Call LED BlinkCall LED ONTX Low BATT2 R TX• TX: Turns Red while transmitting a signal.• RX: Turns Green while receiving a signal.For IC-F3013/IC-F4013 only• Call LED (ON): When receiving a matched 2/5-tone.• Call LED (Blink): When receiving a matched 2/5-tone.• Fast/Slow scan: Blinks while Fast/Slow scan is activated.• Low BATT1: You should charge the battery. (blinks slowly)• Low BATT2: You must charge the battery. (blinks fast)• TX low BATT2: Low BATT2 was detected during TX mode.• CH error: Non-programmed channel is selected.

92PANEL DESCRIPTION■ Programmable function keysThe following functions can be assigned to [Upper] and [Lower] programmable function keys.Consult your Icom dealer or system operator for details concerning your transceivers programming.D For All modelsSCAN A KEY➥ Push to start and cancel scanning operation.➥ When the Power ON scan function is turned ON, push to pause the scanning operation. The paused scan restarts after the spec-iﬁed time period has passed.SCAN B KEYPush to start and cancel scanning operation. In case of transmis-sion during scan, pauses scanning. The paused scan restarts after the speciﬁed time period has passed.PRIORITY CHANNEL KEYS➥ Push to select the Priority A or Priority B channel.➥ Push and hold [Prio A (Rewrite)] to rewrite the Prio A channel.MR-CH 1/2/3/4 KEYSPush to select a memory channels 1 to 4 directly.1234567891011121314151617181920

102PANEL DESCRIPTIONOUTPUT POWER SELECTION KEYSelect the transmit output power temporarily or permanently, de-pending on the pre-setting.• Ask your dealer for the output power level for each selection.TALK AROUND KEY➥ Push to turn the talk around function OFF.➥ Push and hold to turn the talk around function ON. • The talk around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver communication.WIDE/NARROW KEY➥ Push to select the IF bandwidth to wide. • The wide passband width can be selected from 25 or 20 kHz using the optional cloning software (PMR operation only). Ask your dealer for details.➥ Push and hold to select the IF bandwidth to narrow.SIREN KEYPush to emit a siren. This function can be used for situations other than an emergency alert such as a security alarm for example.LOCK KEYPush and hold to electronically lock all programmable keys except the followings: [Moni(Audi)], [Call] (incl. Call A and Call B)* and [Emergency Single]/[Emergency Repeat] (incl. Silent)*.* Available for IC-F3013/IC-F4013 only.

112PANEL DESCRIPTIONMONITOR KEY ➥ Push to mute and release the CTCSS (DTCS) or 2Tone* squelch mute. Open any squelches/deactivate any mutes while pushing this key. (LMR operation only) * Available for the IC-F3013/F4013 only.➥ Activates one of (or two of) the following functions on each chan-nel independently: (PMR operation only) • Push and hold to un-mute the channel (audio is emitted; ‘Audible’). • Push to mute the channel (audio is not emitted; ‘Inaudible’). • Push to send a ‘reset code’ after the communication is ﬁnished. NOTE: The un-mute condition (‘Audible’ condition) may auto-matically return to the mute condition (‘Inaudible’ condition) after a speciﬁed period.D For IC-F3013/IC-F4013 onlyDTMF AUTODIAL KEYPush to transmit the programmed DTMF code.CALL KEYSPush to transmit a 2/5-tone code.• Call transmission is necessary before you call another station depend-ing on your signalling system.• [Call A] and/or [Call B] keys may be available when your system em-ploys selective ‘Individual/Group’ calls. Ask your dealer which call is assigned to each key.EMERGENCY SINGLE/EMERGENCY REPEAT KEYS➥ Push and hold for the speciﬁed time period to transmit an emer-gency call once or repeatedly.➥ When [Emergency Single (Silent)] or [Emergency Repeat (Silent)] is pushed, an emergency call is transmitted with no beep emission. • If you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. • The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting.1234567891011121314151617181920

123CONVENTIONAL OPERATION■ Turning power ONRotate [VOL] to turn power ON.■ Channel selectionRotate [CHANNEL SELECTOR] to se-lect the desired operating channel, in sequence; or, push one of [MR-CH 1] to [MR-CH 4] key to select a channel di-rectly.AUTOMATIC SCAN TYPE:Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call.[VOL][CHANNEL SELECTOR]

133CONVENTIONAL OPERATION■ Receiving and transmittingNOTE: Transmitting without an antenna may damage the trans-ceiver. See p. 2 for antenna attachment.Receiving:q Rotate [VOL] to turn power ON.w Rotate [CHANNEL SELECTOR] or push one of [MR-CH 1] to [MR-CH 4] key to select a channel.e When receiving a call, adjust the audio output level to a comfort-able listening level.Transmitting:Wait for the channel to become clear to avoid interference.q While pushing and holding [PTT], speak into the microphone at a normal voice level.w Release [PTT] to return to receive.IMPORTANT: To maximize the readability of your signal;1. Pause brieﬂy after pushing [PTT].2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level.1234567891011121314151617181920

143CONVENTIONAL OPERATIOND Transmitting notes• Transmit inhibit functionThe transceiver has several inhibit functions which restrict trans-mission under the following conditions:- The channel is in mute condition.- The channel is busy.- Un-matched (or matched) CTCSS is received.- The selected channel is a ‘receive only’ channel.• Time-out timerAfter continuous transmission for the pre-programmed time period, the time-out timer activates, and causes the transceiver to stop transmit-ting.• Penalty timerOnce the time-out timer activates, transmission is further inhibited for a period determined by the penalty timer.

153CONVENTIONAL OPERATION■ Setting the squelch levelThe squelch circuit mutes the received audio signal depending on the signal strength.q While pushing [PTT] and [Lower], rotate [VOL] to turn the power ON to enter the squelch level adjust-ment mode.w Push [Upper] to increase the squelch level (tight squelch) or [Lower] to decrease the squelch level (loose squelch).e Rotate [VOL] to turn the power OFF to ﬁx the squelch level.1234567891011121314151617181920[VOL][Upper][Lower][PTT]

164SIGNALING OPERATIONSNOTE: The tone signalling operations are available for the IC-F3013/F4013 only.■ Call procedureWhen your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice trans-mission. The tone signalling employed may be a selective calling system which allows you to call speciﬁc station(s) only and prevent unwanted stations from contacting you.q Select the desired TX code channel or 2/5-tone code according to your System Operator’s instructions. • This may not be necessary depending on programming.w Push [Call]. (p. 11)e After transmitting a 2/5-tone code, the remainder of your com-munication can be carried out in the normal fashion.Selective calling Non-selective callingD Transmitting notes— PTTID callThe transceiver sends the ID code (5-tone, DTMF or digital ANI) automatically when [PTT] is pushed (beginning of transmission) and released (end of transmission) depends on the setting.

174SIGNALING OPERATIONS1234567891011121314151617181920■ Emergency CallWhen [Emergency Single] or [Emergency Repeat] (p. 11) is pushed and held for the speciﬁed time period, the emergency sig-nal (5-tone, DTMF or MDC 1200) is transmitted once or repeatedly on the emergency channel. A repeat emergency signal is auto-matically transmitted until it receives the acknowledgement signal. When no emergency channel is speciﬁed, the signal is transmitted on the previously selected channel.If you want to cancel the emergency call, push and hold the key again before transmitting the call.The emergency call can be transmitted without a beep emission, and the LCD indication if [Emergency Single (Silent)] or [Emer-gency Repeat (Silent)] (p. 11) is pushed.The transceiver can also be programmed to keep the microphone open during an emergency call, allowing monitoring of the situa-tion.IMPORTANT: It is recommended to set an emergency channel individually to provide the certain emergency call operation.■ DTMF transmissionIf the transceiver has [DTMF Autodial] assigned to it, the auto-matic DTMF transmission function is available.➥ Push [DTMF Autodial] to transmit the DTMF code.

185BATTERY CHARGING■ CautionMisuse of Lithium-ion batteries may result in the following hazards: smoke, ﬁre, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance.R DANGER! Use and charge only speciﬁed Icom battery packs with Icom radios or Icom charger. Only Icom battery packs are tested and approved for use and charge with Icom radios or Icom charger. Using third-party or counterfeit battery packs or charger may cause smoke, ﬁre, or cause the battery to burst.D Battery cautionR DANGER! DO NOT hammer or otherwise impact the battery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch ﬁre.R DANGER! NEVER use or leave battery packs in areas with temperatures above +60˚C (+140˚F). High temperature buildup in the battery, such as could occur near ﬁres or stoves, inside a sun heated car, or in direct sunlight may cause the battery to rupture or catch ﬁre. Excessive temperatures may also degrade battery per-formance or shorten battery life.R DANGER! DO NOT expose the battery to rain, snow, seawater, or any other liquids. Do not charge or use a wet battery. If the bat-tery gets wet, be sure to wipe it dry before using. The battery is not waterproof.

195BATTERY CHARGINGR DANGER! NEVER incinerate used battery packs since internal battery gas may cause them to rupture, or may cause an explosion.R DANGER! NEVER solder the battery terminals or NEVER mod-ify the battery pack. This may cause heat generation, and the bat-tery may rupture, emit smoke or catch ﬁre.R DANGER! Use the battery only with the transceiver for which it is speciﬁed. Never use a battery with any other equipment, or for any purpose that is not speciﬁed in this instruction manual.R DANGER! If ﬂuid from inside the battery gets in your eyes, blind-ness can result. Rinse your eyes with clean water, without rubbing them, and see a doctor immediately.WARNING! Immediately stop using the battery if it emits an ab-normal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor.WARNING! Immediately wash, using clean water, any part of the body that comes into contact with ﬂuid from inside the battery.WARNING! NEVER put the battery in a microwave oven, high-pressure container, or in an induction heating cooker. This could cause a ﬁre, overheating, or cause the battery to rupture.CAUTION! Always use the battery within the speciﬁed temperature range for the transceiver (–30˚C to +60˚C; –22˚F to +140˚F) and the battery itself (–20˚C to +60˚C; –4˚F to +140˚F). Using the bat-tery out of its speciﬁed temperature range will reduce the battery’s performance and battery life.1234567891011121314151617181920

205BATTERY CHARGINGCAUTION! Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50˚C; +122˚F) for an extended period of time. If the battery must be left unused for a long time, it must be de-tached from the radio after discharging. You may use the battery until the remaining capacity is about half, then keep it safely in a cool dry place with the temperature range as below: –20˚C to +50˚C (–4˚F to +122˚F) (within a month) –20˚C to +35˚C (–4˚F to +95˚F) (within three months) –20˚C to +20˚C (–4˚F to +68˚F) (within a year)D Charging cautionR DANGER! NEVER charge the battery pack in areas with ex-tremely high temperatures, such as near ﬁres or stoves, inside a sun heated car, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the bat-tery to stop charging.WARNING! DO NOT charge or leave the battery in the battery charger beyond the speciﬁed time for charging. If the battery is not completely charged by the speciﬁed time, stop charging and re-move the battery from the battery charger. Continuing to charge the battery beyond the speciﬁed time limit may cause a ﬁre, overheat-ing, or the battery may rupture.WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof.CAUTION! DO NOT charge the battery outside of the speciﬁed temperature range: BC-160 (0˚C to +40˚C; +32˚F to +104˚F). Icom recommends charging the battery at +20˚C (+68˚F). The battery may heat up or rupture if charged out of the speciﬁed temperature range. Additionally, battery performance or battery life may be re-duced.

215BATTERY CHARGING■ Battery chargersD Rapid charging with the BC-160The optional BC-160 provides rapid charging of the Li-Ion battery pack. Charging period: Approx. 3 hours (with BP-232N)The following items are additionally required:• An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-17L) is additionally required.AC adapter(Not supplied with some versions.)Optional OPC-515L (for 13.8 V power source) or CP-17L (for 12 V cigarette lighter socket) can be used instead of the AC adapter.Battery pack TransceiverTurn power OFFIMPORTANT!Ensure the guide lobes on the battery pack are correctly aligned with the guide rails inside the charger adapter.Guide railLobes1234567891011121314151617181920

225BATTERY CHARGINGD Regular charging with the BC-171The optional BC-171 provides regular charging of the Li-Ion battery pack. Charging period: Approx. 10 hours (with BP-232N)The following items are additionally required:• An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-17L) is additionally required.AC adapter(Not supplied with some versions.)Optional OPC-515L (for 13.8 V power source) or CP-17L (for 12 V cigarette lighter socket) can be used instead of the AC adapter.Battery pack TransceiverTurn power OFFIMPORTANT!Ensure the guide lobes on the battery pack are correctly aligned with the guide rails inside the charger adapter.Guide railLobes

235BATTERY CHARGINGD AD-106 installationThe AD-106 charger adapter must be installed into the BC-119N or BC-121N before battery charging.➥Connect the AD-106 charger adapter and the BC-119N/BC-121N as below, then install the AD-106 into the holder space of the BC-119N or BC-121N with the supplied screws.Desktop chargeradapterConnectorsPlugsScrews supplied with the charger adapterThis illustration is described with the BC-119N.1234567891011121314151617181920

245BATTERY CHARGINGD Rapid charging with the BC-119N+AD-106The optional BC-119N provides rapid charging of the Li-Ion battery pack. Charging period: Approx. 3 hours (with BP-232N)The following items are additionally required:• An AD-106 (purchase separately).• An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-17L).AD-106 charger adapter is installed in BC-119N.AC adapter(Not supplied with some versions.)Optional OPC-515L (for 13.8 V power source) or CP-17L (for 12 V cigarette lighter socket) can be used instead of the AC adapter.Battery packTransceiverIMPORTANT!Ensure the guide lobes on the bat-tery pack are correctly aligned with the guide rails inside the charger adapter. Guide railsTurn power OFFLobes

255BATTERY CHARGING1234567891011121314151617181920D Rapid charging with the BC-121N+AD-106The optional BC-121N allows up to 6 battery packs to be charged simultaneously. Charging period: Approx. 3 hours (with BP-232N)The following items are additionally required.• Six AD-106.• An AC adapter (BC-157) or the DC power cable (OPC-656)AC adapter(Purchase separately)AD-106 charger adapters are installed in each slot.DC power cable(OPC-656)(Connect with the DC power supply; 13.8 V/at least 7 A)IMPORTANT!Ensure the guide lobes on the bat-tery pack are correctly aligned with the guide rails inside the charger adapter.Guide railsLobesBattery packTransceiver Turn power OFF

276BATTERY CASE1234567891011121314151617181920qBP-240wFig.1Fig.2Fig.3ert

287SWIVEL BELT CLIP■ MB-93 contents Qty.q Belt clip .................................................................................... 1w Base clip .................................................................................. 1■ To attachq Release the battery pack if it is attached. (p. 3)w Slide the base clip in the direction of the arrow until the base clip is locked and makes a ‘click’ sound.q w

297SWIVEL BELT CLIPe Clip the belt clip to a part of your belt. And insert the transceiver into the belt clip until the base clip inserted fully into the groove.r Once the transceiver is locked in place, it swivels as illustrated below.Once the transceiver is locked in place,it will swivel 360 degrees.1234567891011121314151617181920

307SWIVEL BELT CLIP■ To detachq Turn the transceiver upside down in the direction of the arrow and pull out from the belt clip.

317SWIVEL BELT CLIP6w Release the battery pack if it is attached. (p. 3)e Pinch the clip (q), and slide the base clip in the direction of the arrow (w).qwCAUTION:HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP.Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged.123457891011121314151617181920

328OPTIONSD BATTERY PACKBattery pack Voltage Capacity Battery life*1BP-230N 7.4 V 950 mAh (min.)980 mAh (typ.) 9 hrs.BP-232N 7.4 V 1900 mAh (min.)2000 mAh (typ.) 18 hrs.BP-240 Battery case for AAA (LR03) × 6 alkaline —*2*1 When the power save function is turned ON, and the operating pe-riods are calculated under the following conditions; TX : RX : standby = 5 : 5 : 90*2 Operating period depends on the alkaline cells used.D CHARGERS• BC-119N desktop charger + AD-106 charger adapter + BC-145S ac adapter For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: approx. 3 hours when BP-232N is attached.• BC-121N multi-charger + AD-106 charger adapter (6 pcs.) + BC-157 ac adapter For rapid charging of up to 6 battery packs (six AD-106’s are required) simultaneously. An AC adapter should be purchased separately. Charging time: approx. 3 hours when BP-232N is attached.• BC-160 desktop charger + BC-145S ac adapter For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: approx. 3 hours when BP-232N is attached.

338OPTIONS• BC-171 desktop charger + BC-147S ac adapter For regular charging of battery packs. We recommend that the BP-230N charging. An AC adapter is supplied with the charger depending on versions. Charging time: Approx. 10 hours when BP-232N is attached. Approx. 4 hours when BP-230N is attached.D BELT CLIPS• MB-93 swivel belt clip• MB-94 belt clip Exclusive alligator-type belt clip.• MB-96N/96F leather belt hangerD DC CABLES• CP-17L cigarette lighter cable Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-119N)• OPC-515L/OPC-656 dc power cables Allows charging of the battery pack using a 13.8 V power source instead of the AC adapter. OPC-515L: For BC-119N OPC-656 : For BC-121ND ANTENNAS• FA-SC73US/FA-SC56VS/FA-SC57VS stubby antennas FA-SC73US: 450–490 MHz FA-SC56VS: 150–162 MHz FA-SC57VS: 160–174 MHz• FA-SC01U/FA-SC25U/FA-SC57U/FA-SC72U/FA-SC25V/ FA-SC55V antennas FA-SC01U: 350–400 MHz FA-SC25U: 400–430 MHz FA-SC57U: 430–470 MHz FA-SC72U: 470–520 MHz FA-SC25V: 136–155 MHz FA-SC55V: 146–174 MHz• FA-SC61VC/FA-SC61UC cut antennas FA-SC61VC: 136–174 MHz FA-SC61UC: 380–520 MHz1234567891011121314151617181920

348OPTIONSD OTHER OPTIONS• SP-13 earphone Provides clear receive audio in noisy environment.• HM-153L earphone-microphone• HM-131L/158L/159L speaker-microphone Combination speaker-microphone that provides convenient op-eration while hanging the transceiver from your belt.• VS-1L vox/ptt case + HS-94/HS-95/HS-97 headset VS-1L: VOX/PTT switch box for hands-free operation, etc. HS-94: Ear hook type HS-95: Neck-arm type HS-97: Throat microphoneIcom optional equipment are designed for optimal performance when used with this transceiver. We are not responsible for the transceiver being damaged or any accident caused when using non-Icom optional equipment.Some options may not be available in some countries. Please ask your dealer for details.

358OPTIONSD About VS-1L vox/ptt caseThe VS-1L is a VOX/PTT unit for Icom handheld transceivers, and allows you hands-free operation.An optional headset (HS-94, etc.) is additionally required for opera-tion.• The VOX (voice operated transmission) function starts transmission without pushing PTT switch when you speak into the microphone; then, automatically returns to receive when you stop speaking.Features➥ Straight type head SP/MIC plug equipped➥ Water resistant construction➥ Durable construction➥ Equipped with a PTT switch and revolving clip.MIC/VOX gain adjustment1 Remove the water protection cover on the right side of the VS-1L.2 Adjust the MIC/VOX gain with a thin screw driver. Clockwise rota-tion increases the MIC/VOX gain.3 Return the protective cover back to the MIC/VOX gain adjustment hole.VS-1LVOXPTTAdjusting potWater protection coverPTT switch1234567891011121314151617181920

369FCC INFORMATION• FOR CLASS B UNINTENTIONAL RADIATORS:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi-sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.

MEMO1234567891011121314151617181920

MEMO

MEMO1234567891011121314151617181920

MEMO

MEMO1234567891011121314151617181920

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, JapanA-6768H-1EX-qPrinted in Japan© 2009 Icom Inc.Printed on recycled paper with soy ink.

Navigation menu