ICOM orporated 283300 UHF Transceiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	490696
Application ID	X2clkNRqJSWdYHnL/bYnpQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	282.55kB (3531919 bits)
Date Submitted	2004-11-23 00:00:00
Date Available	2004-11-23 00:00:00
Creation Date	2004-10-18 00:34:03
Producing Software	Acrobat Distiller 5.0.5 for Macintosh
Document Lastmod	2004-11-16 11:53:16
Document Title	Users Manual

INSTRUCTION MANUAL
VHF TRANSCEIVER
iV82
UHF TRANSCEIVER
iU82
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
(IC-V82)
FOREWORD
IMPORTANT
Thank you for purchasing this Icom product. The IC-V82/U82
VHF/UHF TRANSCEIVERS is designed and built with Icom’s superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation.
READ ALL INSTRUCTIONS carefully and completely
We want to take a couple of moments of your time to thank
you for making your IC-V82/U82 your radio of choice, and
hope you agree with Icom’s philosophy of “technology first.”
Many hours of research and development went into the design of your IC-V82/U82.
D FEATURES
❍ 7 W* of high transmit output power
(*IC-V82, 5W for IC-U82)
❍ CTCSS and DTCS encoder/decoder standard
before using the transceiver.
SAVE THIS INSTRUCTION MANUAL— This instruction manual contains important operating instructions for
the IC-V82/U82.
EXPLICIT DEFINITIONS
WORD
DEFINITION
Personal injury, fire hazard or electric shock
R WARNING!
may occur.
CAUTION
NOTE
Equipment damage may occur.
Recommended for optimum use. No risk of
personal injury, fire or electric shock.
❍ Optional Digital modulator/demodulator
❍ Optional DTMF decoder
❍ MIL-STD810 grade durability
Icom, Icom Inc. and the
logo are registered trademarks of Icom
Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
PRECAUTION
RWARNING! NEVER hold the transceiver so that the
antenna is very close to, or touching exposed parts of the
body, especially the face or eyes, while transmitting. The
transceiver will perform best if the microphone is 5 to 10 cm
(2 to 4 inches) away from the lips and the transceiver is vertical.
Place the unit in a secure place to avoid inadvertent use by
children.
DO NOT operate the transceiver near unshielded electrical
blasting caps or in an explosive atmosphere.
AVOID using or placing the transceiver in direct sunlight or
RWARNING! NEVER operate the transceiver with a
in areas with temperatures below –10°C (+14˚F) or above
+60°C (+140˚F).
headset or other audio accessories at high volume levels.
Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the
volume or discontinue use.
The use of non-Icom battery packs/chargers may impair
transceiver performance and invalidate the warranty.
DC fused at more than 5 A. Accidental reverse connection will
be protected by this fuse, but higher fuse values will not give
any protection against such accidents and the transceiver will
be ruined.
Even when the transceiver power is OFF, a slight current still
flows in the circuits. Remove the battery pack or case from
the transceiver when not using it for a long time. Otherwise,
the battery pack or installed rechargeable batteries (Ni-Cd:
BP-222N, BP-209N, Ni-MH: BP-210N, Li-Ion: BP-211N) will
become exhausted.
NEVER attempt to charge alkaline or dry cell batteries. Be
aware that external DC power connections will charge batteries inside the battery case. This will damage not only the battery case but also the transceiver.
For USA only:
Caution: Changes or modifications to this transceiver, not expressly approved by Icom Inc., could void your authority to
operate this transceiver under FCC regulations.
NEVER connect the transceiver to a power source that is
DO NOT push the PTT when not actually desiring to transmit.
ii
SUPPLIED ACCESSORIES
■ Supplied Accessories
q Antenna* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
w Belt clip (with screws) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
e AC Adapter* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
r Battery pack*/Battery case* . . . . . . . . . . . . . . . . . . . . . . 1
t Battery charger*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 set
*Not supplied with some versions.
iii
SAFETY TRAINING INFORMATION
CAUTION
To ensure that your exposure to RF electromagnetic energy is within the FCC allowable limits, always adhere to
the following guidelines:
• DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause
you to exceed FCC RF exposure limits. A proper antenna is
the antenna supplied with this radio by the manufacturer or
an antenna specifically authorized by the manufacturer for
use with this radio.
• DO NOT transmit for more than 50% of total radio use time
(“50% duty cycle”). Transmitting more than 50% of the time
can cause FCC RF exposure compliance requirements to
be exceeded. The radio is transmitting when the “TX indicator” is lit. You can cause the radio to transmit by pressing
the “PTT” switch.
• ALWAYS use Icom authorized accessories (antennas, batteries, belt clips, speaker/mics, etc.). Use of unauthorized
accessories can cause the FCC RF exposure compliance
requirements to be exceeded.
• ALWAYS keep the antenna at least 2.5 cm (1 inch) away
from the body when transmitting, and only use the Icom
belt-clips which are listed in this manual when attaching the
radio to your belt, etc. To provide the recipients of your
transmission the best sound quality, hold the antenna at
least 5 cm (2 inches) from your mouth, and slightly off to one
side.
The information listed above provides the user with the
information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates
within the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility. During transmissions, your Icom radio generates RF energy that can
possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in
areas where signs are posted to do so. DO NOT operate
the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting
sites.
iv
TABLE OF CONTENTS
FOREWORD .................................................................................... i
IMPORTANT..................................................................................... i
EXPLICIT DEFINITIONS.................................................................. i
PRECAUTION ................................................................................. ii
SUPPLIED ACCESSORIES ........................................................... iii
SAFETY TRAINING INFORMATION.............................................. iv
TABLE OF CONTENTS .............................................................. v–vi
QUICK REFERENCE................................................................... I–V
■ Preparation............................................................................... I
■ Your first contact..................................................................... III
■ Repeater operation ................................................................ IV
■ Programming memory channels ............................................. V
1 ACCESSORIES...................................................................... 1–2
■ Accessory attachment............................................................. 1
2 PANEL DESCRIPTION .......................................................... 3–7
■ Switches, controls, keys and connectors ................................ 3
■ Function display ...................................................................... 6
3 BATTERY PACKS ................................................................ 8–12
■ Battery pack replacement ....................................................... 8
■ Battery caution ........................................................................ 9
■ Charging NOTE ...................................................................... 9
■ Battery charging .................................................................... 10
■ Battery case (optional for some versions) ............................ 12
4 BASIC OPERATION........................................................... 13–16
■ Power ON.............................................................................. 13
■ VFO mode selection.............................................................. 13
■ Setting a frequency ............................................................... 13
■ Setting audio/squelch level ................................................... 15
■ Receive and transmit ............................................................ 15
■ Display type........................................................................... 16
■ Key lock function ................................................................... 16
5 REPEATER OPERATION .................................................. 17–19
■ General ................................................................................. 17
■ Offset frequency .................................................................... 17
■ Subaudible tones .................................................................. 18
■ Auto repeater function (USA versions only) .......................... 19
■ Repeater lockout ................................................................... 19
6 MEMORY/CALL OPERATION ........................................... 20–25
■ General description ............................................................... 20
■ Selecting a memory channel................................................. 20
■ Selecting the call channel ..................................................... 20
■ Programming the memory/call channels ............................... 21
■ Channel name programming................................................. 22
■ Memory transferring .............................................................. 22
■ Memory bank selection ......................................................... 24
■ Memory bank setting............................................................. 24
■ Transferring bank contents.................................................... 25
7 DTMF MEMORY................................................................. 26–27
■ Programming a DTMF code .................................................. 26
■ Transmitting a DTMF code.................................................... 27
■ DTMF transmission speed .................................................... 27
8 SCAN OPERATION............................................................ 28–31
■ Scan types ............................................................................ 28
■ Programmed scan................................................................. 28
■ Memory scan..........................................................................29
■ Skip channels........................................................................ 30
■ Priority watch......................................................................... 30
■ Scan resume condition.......................................................... 31
9 SUBAUDIBLE TONES ....................................................... 32–35
■ Tone squelch ......................................................................... 32
■ Pocket beep operation .......................................................... 34
■ Tone scan.............................................................................. 35
10 PAGER/CODE SQUELCH (Required Optional UT-108) .. 36–39
■ Pager function ....................................................................... 36
■ Code programming ............................................................... 36
■ Pager operation..................................................................... 38
■ Code squelch ........................................................................ 39
11 DIGITAL MODE OPERATION
(Required Optional UT-118)...............................................40–56
■ Digital mode operation .......................................................... 40
■ Call sign programming .......................................................... 40
■ Digital voice mode operation ................................................. 43
■ When receiving a Digital call ................................................. 44
■ Break-in communication ....................................................... 45
■ EMR communication ............................................................. 46
■ Pocket beep operation .......................................................... 46
■ Digital squelch functions ....................................................... 47
■ Digital monitor ....................................................................... 47
■ Low-speed data communication ........................................... 48
■ About D-STAR system .......................................................... 49
■ Repeater call sign programming ........................................... 50
■ Other setting items ................................................................ 51
■ GPS operation ...................................................................... 55
12 OTHER FUNCTIONS ......................................................... 57–67
■ SET MODE............................................................................ 57
■ INITIAL SET MODE .............................................................. 61
■ Weather channel operation (IC-V82 [USA] versions only) .... 66
■ CPU reset.............................................................................. 67
■ Partial reset ........................................................................... 67
13 CLONING ................................................................................. 68
14 OPTIONAL UNIT ................................................................ 69–70
■ Optional UT-108/118 installation ........................................... 69
■ Optional MB-86 installation ................................................... 69
15 SPECIFICATIONS .................................................................... 71
■ IC-V82 ................................................................................... 71
■ IC-U82 ................................................................................... 72
16 OPTIONS.................................................................................. 73
10
11
12
13
14
15
16
17 CE ............................................................................................. 75
vi
QUICK REFERENCE GUIDE
■ Preparation
D Battery pack replacement
Before replacing the battery pack, push [PWR] for 1 sec. to
turn the power OFF.
• Slide the battery release forward, then pull the battery pack upward
with the transceiver facing away from you.
D Charging with the BC-144N/146
The optional BC-144N provides rapid charging, and the BC146 provides regular charging of an optional battery pack
with/without transceiver. The following is additionally required:
• An optional AC adapter. (An AD-99N is supplied with BC-144N or
BC-146.)
Turn power OFF.
D Battery case— optional for some versions
Check orientation
for correct charging. (Insert together
with AD-99N.)
When using a BP-208N BATTERY CASE attached to the transceiver, install 6 AA (LR6) size alkaline batteries as illustrated
below.
BC-144N/146
+AD-99N
D About AD-99N
D Antenna
The adapter (Spacer A) only is required for IC-V82 series.
When removing the spacer (Spacer B/C), push the notch carefully with your finger to remove the spacer (Spacer B/C) from
the adapter (Spacer A).
Attach the antenna to the transceiver
as illustrated at right.
Remove the spacer (Spacer B/C)
from the adapter.
Push the notch
carefully.
Quick reference guide
QUICK REFERENCE GUIDE
R CAUTION!
DO NOT push or force the notch with a screw driver, etc.,
to remove it.
DO NOT bend the notch when the adapter and spacer are
not joined together. This will cause weakening of the notch
plastic.
Both cases may break the notch and it may not be able to
be reattached.
D Belt clip
Conveniently attaches to your belt.
Attach the belt clip with the supplied screws using a phillips
screwdriver.
To attach the belt clip
II
QUICK REFERENCE GUIDE
■ Your first contact
Now that you have your IC-V82/U82 ready, you are exited to
get on the air. We would like to walk you through a few basic
operational steps to make your first “On The Air” use an enjoyable experience.
2. Adjusting audio output level
➥ Rotate [VOL] to set the desired
audio level.
[VOL]
3. Adjusting the squelch level
D About default setting
Y]/[Z
Z] keys funcThe [VOL] control function can be traded with [Y
tion in INITIAL SET MODE. However, in this QUICK REFERENCE,
the factory default setting ([VOL] controls audio output level) is
used for simple instructions.
➥ While pushing and holding
Y] or [Z
Z] to set the
[MONI], push [Y
squelch level.
D Basic operation
1. Turning ON the transceiver
4. Tune the desired frequency
Although you have purchased a brand new transceiver, some
settings may be changed from the factory defaults because
of the QC process. Resetting the CPU is necessary to start
from factory default.
Y]/[Z
Z], will
The up/down keys, [Y
allow you to tune the frequency that
you want to operate on. Page 14 will
instruct you on how to adjust the tuning step.
➥ While pushing [MONI] and
[D•CLR], push [PWR] for 1 sec. to
reset the CPU and turn power ON.
Y] or [Z
Z] to adjust the fre➥ Push [Y
quency.
MONI
PWR
CLR
III
MONI
Direct frequency input from the keypad is also available.
■ Repeater operation
➥ To enter the desired frequency,
enter 6-digits starting from the
100 MHz digit.
1. Setting duplex
➥ Push [A•FUNC], then [4•DUP] several times to select minus duplex
or plus duplex.
• Enter three* to five digits then pushing [✱•ENT
] is also set the frequency. (*Some versions are
available from two digits.)
• When a digit is mistakenly input,
push [D.CLR] to abort to input.
CLR
ENT
• The USA version has an auto repeater function, therefore, setting duplex is not required.
Keypad
FUNC
Quick reference guide
QUICK REFERENCE GUIDE
DUP
• Example 1— when entering 145.525 MHz
Push
TONE
DUP
SCAN
SCAN
P.BEEP
SCAN
2. Repeater tone
➥ Push [A•FUNC], then [1•TONE]
several times until “ ” appears, if
required.
• Example 2— when entering 144.800 MHz
Push
TONE
DUP
DUP
SET
OPT
ENT
FUNC
TONE
5. Transmit and receive
➥ Push and hold [PTT] to transmit, then speak into the microphone; release to receive.
IV
QUICK REFERENCE GUIDE
■ Programming memory channels
The IC-V82/U82 has a total of 207 memory channels (including 6 scan edges and 1 call channel) for storing often used
operating frequency, repeater settings, etc.
➥ Push [A•FUNC], then push [C•MR]
for 1 sec. to program.
• 3 beeps sound
1. Setting frequency
In VFO mode, set the desired operating frequency with other
desired settings, such as repeater and subaudible tone.
2. Selecting a memory channel
MR
FUNC
➥ Push [A•FUNC], [C•MR] then push
Y] or [Z
Z] several times to select
[Y
the desired memory channel.
• Continue to hold [C•MR] down for 1 sec. after 3 beeps are emitted, to increment the displayed memory channel number.
• “X” indicator and memory channel
number blink.
MR
FUNC
3. Writing a memory channel
ACCESSORIES
■ Accessory attachment
D Antenna
Attach the antenna to the transceiver as illustrated below.
Keep the [SP/MIC] cap (SP/MIC jack cover) attached when
jacks are not in use to avoid bad contacts.
Attach the
[SP/MIC] cap.
[SP/MIC] cap
1
ACCESSORIES
D Belt clip
D Handstrap (Not supplied)
Conveniently attaches to your belt.
Attach the belt clip with the supplied screws using a phillips
screwdriver.
To attach the belt clip
Slide the hand strap through the loop on the top of the rear
panel as illustrated below. Facilitates carrying.
PANEL DESCRIPTION
■ Switches, controls, keys and connectors
q CONTROL DIAL [VOL]
*Rotate to adjust the volume level.
w PTT SWITCH [PTT]
Push and hold to transmit; release to receive.
Y]/[Z
Z]
e UP/DOWN KEYS [Y
*Selects the operating frequency.
Speaker
MONI
FUNC
CALL
MR
TONE
DUP
PRIO
P.BEEP
SCAN
SET
T.SCAN
SKIP
H/M/L
PWR
t ANTENNA CONNECTOR
Connects the supplied antenna.
u FUNCTION DISPLAY (pgs 6, 7)
r KEY PAD (pgs. 4, 5)
Used to enter operating frequency, the DTMF codes, etc.
y [SP]/[MIC] JACK
Connect an optional speaker-microphone or headset, if desired. The internal microphone and speaker will not function when either is connected.
Microphone
i SQUELCH/MONITOR SWITCH [MONI]
Push and hold to force the squelch open and set the transceiver to the squelch level adjustable condition.
CLR
BANK
OPT
ENT
!0
o POWER SWITCH [PWR]
Push for 1 sec. to turn the power ON and OFF.
Y]/[Z
Z] can be
*The assigned function for [VOL] and [Y
traded in INITIAL SET MODE (pgs. 14, 63).
2
PANEL DESCRIPTION
!0 [DATA] JACK
Connect to a PC or GPS receiver via the RS232C cable (Dsub 9 pin) for data communication in the RS-232C format.
Pin 2 (RxD),
Pin 3 (TxD),
Pin 5 (GND)
to [DATA] jack
TxD GND
RxD
2.5(d) mm
Less than
10(d) mm
D Key pad
FUNC
[A•FUNC]
Access to secondary function.
CALL
[B•CALL]
Select the call channel. (p. 20)
MR
RS-232C
(DB-9 female)
Make sure the connection between transceiver and PC, otherwise misreading may occur for data communication.
CLR
[D•CLR]
Selects VFO mode, aborts direct frequency input,
or cancels scanning, etc. (pgs. 13, 28)
[1•TONE]
➥ Input digit “1” during frequency input, memory
channel selection, etc. (pgs. 13, 20)
➥ After pushing [A•FUNC], selects the subaudible
tone function. (pgs. 17, 32)
[2•P.BEEP]
➥ Input digit “2” during frequency input, memory
channel selection, etc. (pgs. 13, 20)
➥ After pushing [A•FUNC], turn the pocket beep
function ON and OFF. (p. 34)
TONE
P.BEEP
[C•MR]
➥ Selects a memory mode. (p. 20)
➥ After pushing [A•FUNC], entering into memory
programming/editing mode. (pgs. 21–23)
➥ After pushing [A•FUNC], programs/transfers
VFO/memory or call channel contents into
memory channel/VFO when pushed for 1 sec.
(pgs. 21–23)
PANEL DESCRIPTION
T.SCAN
DUP
SCAN
SKIP
PRIO
[3•T.SCAN]
➥ Input digit “3” during frequency input, memory
channel selection, etc. (pgs. 13, 20)
➥ After pushing [A•FUNC], starts the tone scanning. (pgs. 18, 35)
[4•DUP]
➥ Input digit “4” during frequency input, memory
channel selection, etc. (pgs. 13, 20)
➥ After pushing [A•FUNC], selects a duplex function (–duplex, +duplex, simplex). (p. 17)
[5•SCAN]
➥ Input digit “5” during frequency input, memory
channel selection, etc. (pgs. 13, 20)
➥ After pushing [A•FUNC], starts scanning. (p. 28)
[6•SKIP]
➥ Input digit “6” during frequency input, memory
channel selection, etc. (pgs. 13, 20)
➥ After pushing [A•FUNC], sets and cancels skip
setting for memory skip scan during memory
mode. (p. 30)
[7•PRIO]
➥ Input digit “7” during frequency input, memory
channel selection, etc. (pgs. 13, 20)
➥ After pushing [A•FUNC], starts the priority
watch. (p. 30)
SET
[8•SET]
➥ Input digit “8” during frequency input, memory
channel selection, etc. (pgs. 13, 20)
➥ After pushing [A•FUNC], enters into SET MODE.
(p. 57)
[9•H/M/L]
➥ Input digit “9” during frequency input, memory
channel selection, etc. (pgs. 13, 20)
➥ After pushing [A•FUNC], switches transmit
power from high, middle and low output power.
(p. 15)
[0•OPT]
➥ Input digit “0” during frequency input, memory
channel selection, etc. (pgs. 13, 20)
➥ After pushing [A•FUNC], selects an optional
function mode, such as pager, code squelch or
digital operation. (pgs. 38, 40)
H/M/L
OPT
BANK
ENT
[#•BANK]
After pushing [A•FUNC], enters a memory bank
condition. (p. 24)
[✱•ENT ]
➥ Sets the frequency even if the full 6-digits of
frequency have not been entered. (p. 13)
➥ After pushing [A•FUNC], switches key lock function ON and OFF when pushed for 1 sec. Lock
all keys, except [PWR], [PTT], [MONI] and
audio level adjustment. (p. 16)
2
PANEL DESCRIPTION
■ Function display
!5
!4
!3
!2
q FUNCTION INDICATOR
Appears while a secondary function is being accessed.
w KEY LOCK INDICATOR (p. 16)
Appears when the key lock function is ON.
e AUTO POWER OFF INDICATOR (p. 62)
Appears while the auto power OFF function is activated.
r DUPLEX INDICATOR (p. 17)
Either “–” or “+” appears during repeater operation.
!1
!0
oi
t TONE INDICATOR
❍ While in the analog (FM) mode operation
➥ “ ” appears while the subaudible tone encoder is in
use. (p. 17)
➥ “ ” appears while the tone (CTCSS) squelch function is in use. (p. 32)
➥ “ ” appears while the tone (DTCS) squelch function
is in use. (p. 32)
➥ “ ” appears with the “ ” or “ ” indicator while the
pocket beep function (CTCSS or DTCS) is in use.
(p. 34)
PANEL DESCRIPTION
❍ While in the digital (DV) mode operation with the installing an optional Digital unit UT-118.
➥ “ ” appears while the digital code (CSQL) squelch
function is in use. (p. 47)
➥ “ ” appears while the call sign (DSQL) squelch function is in use. (p. 47)
➥ “ ” appears with the “ ” or “ ” indicator while the
pocket beep function (CSQL or DSQL) is in use.
(p. 46)
y TRANSMIT INDICATOR (p. 15)
Appears during transmit.
u FREQUENCY READOUT
Shows operating frequency, channel number or channel
names, depending on display type (p. 16).
i SIGNAL INDICATOR
➥ Shows receiving signal strength as below.
Weak ⇐ RX Signal level ⇒ Strong
➥ Shows the output power level while transmitting.
Low
Middle
High
o BUSY INDICATOR
➥ Appears when a signal is being received or the squelch
is open.
➥ Blinks while the monitor function is activated. (pgs.15,
47)
!0 PAGER CALL INDICATOR (p. 39)
Blinks when a pager call is received. (This indicator appears only when UT-108 is installed.)
!1 DIGITAL MODE INDICATOR (p. 43)
Appears when digital mode is selected. (This indicator appears only when UT-118 is installed.)
!2 LOW/MIDDLE POWER INDICATOR (p. 15)
➥ “L” or “M” appears when the low or middle output power
is selected, respectively.
➥ No indicator appears when high output power is selected.
!3 SKIP CHANNEL INDICATOR (p. 30)
Appears when the selected memory channel is specified
as a skip channel.
!4 MEMORY MODE INDICATOR (p. 20)
Appears while in memory mode or channel number indication mode.
!5 MEMORY CHANNEL INDICATOR (p. 20)
➥ Shows the selected memory channel number.
➥ “C” appears when the call channel is selected.
3
BATTERY PACKS
■ Battery pack replacement
D BATTERY PACKS
Battery
pack
➥ Before replacing the battery
pack, push [PWR] for 1 sec.
to turn the power OFF.
BP-208N
Capacity
Battery case for AA
(LR6)×6 alkaline
Battery life*1
—*2
BP-209N
7.2 V
1100 mAh
3 hrs. 20 min.
BP-210N
7.2 V
1650 mAh
6 hrs.
PWR
BP-211N
7.4 V
1800 mAh
6 hrs. 10 min.
Push
for 1 sec.
BP-222N
7.2 V
600 mAh
2 hrs. 15 min.
➥ Slide the battery release forward, then pull the battery pack
upward with the transceiver facing away from you.
Voltage
*1 Operating periods are calculated under the following conditions;
Tx : Rx : standby =1 : 1 : 8, power save function: auto setting is
activated
*2 Operating period depends on the alkaline cells used.
BATTERY PACKS
■ Battery caution
■ Charging NOTE
RDANGER! Use/Charge the specified Icom batteries only.
Prior to using the transceiver for the first time, the battery
pack must be fully charged for optimum life and operation.
Only tested and approved for use with genuine Icom batteries. Fire and/or explosion may occur when a third party
battery pack or counterfeit product is used/charged.
• CAUTION! NEVER short the terminals of the battery pack
(or charging terminals of the transceiver). Also, current may
flow into nearby metal objects such as a necklace, so be
careful when placing battery packs (or the transceiver) in
handbags, etc.
Simply carrying with or placing near metal objects such as a
necklace, etc. causes shorting. This will damage not only
the battery pack, but also the transceiver.
• NEVER incinerate used battery packs. Internal battery gas
may cause an explosion.
• NEVER immerse the battery pack in water. If the battery
pack becomes wet, be sure to wipe it dry BEFORE attaching it to the transceiver.
• Clean the battery terminals to avoid rust or poor contact.
• Keep battery contacts clean. It’s a good idea to clean battery terminals once a week.
If your battery pack seems to have no capacity even after
being charged, completely discharge it by leaving the power
ON overnight. Then, fully charge the battery pack again. If the
battery pack still does not retain a charge (or only very little
charge), a new battery pack must be purchased (p. 73).
• Recommended temperature range for charging:
+10°C to +40°C (; +50˚F to 140˚F)
• Use the supplied charger or optional charger (BC-119N/121N/144N
for rapid charging, BC-146 for regular charging) only. NEVER use
other manufacturers’ chargers.
The optional BP-222N, BP-209N, BP-210N or BP-211N battery packs include rechargeable batteries (Ni-Cd: BP-222N,
BP-209N, Ni-MH: BP-210N, Li-Ion: BP-211N) and can be
charged approx. 300 times. Charge the battery pack before
first operating the transceiver or when the battery pack becomes exhausted.
If you want to charge the battery pack more than 300 times,
the following points should be observed:
• Avoid over charging. The charging period should be less than
24 hours.
• Use the battery until it becomes almost completely exhausted
under normal conditions. We recommend battery charging after
transmitting becomes impossible.
D Battery pack life
When the operating period becomes extremely short even
after charging the battery pack fully, a new battery pack is
needed.
3
BATTERY PACKS
■ Battery charging
D About AD-99N
D Regular charging with the BC-146
The optional BC-146 provides regular charging of an optional
NI-Cd battery pack with/without transceiver. The following is
additionally required:
• An optional AC adapter. (An AD-99N is supplied with BC-146.)
Turn power OFF.
• Chargeable battery
BP-209N, BP-222N
Check orientation for correct
charging. (Insert together
with AD-99N.)
BC-146 +AD-99N
Recommendation:
Charge the BP-211N (Li-Ion) by BC-119N (or BC-121N) for
a maximum of 2 hours. Li-Ion batteries are different from NiCd batteries in that it is not necessary to completely charge
and discharge them to prolong the battery life. Therefore,
charging the battery in intervals, and not for extended periods is recommended.
10
The adapter (Spacer A) only is required for IC-V82/U82 series. When removing the spacer (Spacer B/C), push the notch
carefully with your finger to remove the spacer (Spacer B/C)
from the adapter (Spacer A).
Remove the spacer (Spacer B/C)
from the adapter.
Push the notch
carefully.
R CAUTION!
DO NOT push or force the notch with a screw driver, etc.,
to remove it.
DO NOT bend the notch when the adapter and spacer are
not joined together. This will cause weakening of the notch
plastic.
Both cases may break the notch and it may not be able to
be reattached.
BATTERY PACKS
D Rapid charging with the BC-144N
D Rapid charging with the BC-119N+AD-101
The optional BC-144N provides rapid charging of optional
battery packs.
The following are additionally required:
The optional BC-119N provides rapid charging of battery
packs. The following items are additionally required.
• An AC adapter (may be supplied with the BC-144N depending on
version).
• AD-101.
• An AC adapter (may be supplied with the BC-119N depending on
version) or the DC power cable (OPC-515L/CP17L).
Turn power OFF.
Turn power OFF.
Check orientation for correct
charging. (Insert together
with AD-99N.)
BC-144N +AD-99N
• Chargeable battery
BP-210N (Ni-MH battery)
BP-209N, BP-222N (Ni-Cd batteries)
DC power cable (OPC-515L)
(Connect with the DC power supply;
13.8 V/at least 2 A)
• Chargeable battery
BP-210N (Ni-MH battery)
BP-209N, BP-222N (Ni-Cd batteries)
BP-211N (Li-Ion battery)
11
3
BATTERY PACKS
D Rapid charging with the BC-121N+AD-101
The optional BC-121N allows up to 6 battery packs to be
charged simultaneously. The following items are additionally
required.
• Six AD-101.
• An AC adapter (BC-124; may be supplied with the BC-121N depending on version) or the DC power cable (OPC-656).
■ Battery case
(optional for some versions)
When using a BP-208N BATTERY CASE attached to the
transceiver, install 6 AA (LR6) size alkaline batteries as illustrated below.
Turn power OFF.
AC adapter
(purchased
separately)
MULT
I-CHA
RGER
D CAUTION
Charge indicator
(each indicator functions independently)
DC power cable (OPC-656)
(Connect with the DC power supply;
13.8 V/at least 7 A)
• Chargeable battery
BP-210N (Ni-MH battery)
BP-209N, BP-222N (Ni-Cd batteries)
BP-211N (Li-Ion battery)
12
• Use ALKALINE batteries only.
• Make sure all battery cells are the same brand, type and
capacity. Never mix old and new batteries.
Either of the above may cause a fire hazard or damage
the transceiver if ignored.
• Never incinerate used battery cells since internal battery
gas may cause them to rupture.
• Never expose a detached battery case to water. If the
battery case gets wet, be sure to wipe it dry before use.
4
BASIC OPERATION
■ Power ON
■ Setting a frequency
➥ Push [PWR] for 1 sec. to turn
power ON.
D Via the keypad
q Push [D•CLR] to select VFO mode, if necessary.
w To enter the desired frequency, enter 6-digits starting from
the 100 MHz digit.
PWR
Push
for 1 sec.
■ VFO mode selection
• Enter three* to five digits then pushing [✱•ENT
] is also set the
frequency. (*Some versions are available from two digits.)
• When a digit is mistakenly input, push [D.CLR] to abort to input.
• Example 1— when entering 145.525 MHz
Push
TONE
DUP
SCAN
SCAN
P.BEEP
SCAN
• Example 2— when entering 144.800 MHz
The transceiver has 2 basic operating modes: VFO mode and
memory mode.
Push
TONE
DUP
DUP
SET
OPT
ENT
➥ Push [D•CLR] to select VFO
mode.
CLR
13
4
BASIC OPERATION
D By other methods
D Tuning step selection
Y]/[Z
Z] keys
Via the [Y
The IC-V82/U82 has 8 tuning
steps— 5, 10, 12.5, 15, 20, 25, 30
and 50 kHz. The tuning step is selectable in SET MODE.
Y] or [Z
Z] several times to set the desired frequency.
➥ Push [Y
• Each push increases/decreases the frequency by the selected
tuning step. See right content for tuning step details.
✔ For your information— [VOL] function assignment
The [VOL] control can be used as
a tuning dial for frequency tuning
Y]/[Z
Z] keys. However,
instead of [Y
while [VOL] functions as tuning
Y]/[Z
Z] keys functions as AF
dial, [Y
volume control.
[VOL]
SET
eRotate [VOL] to select the desired tuning step.
r Push [✱•ENT ] to exit SET MODE.
[VOL] is assigned as
tuning dial.
r To exit SET MODE, push [✱•ENT
14
FUNC
ENT
Y] and [Z
Z], turn
qWhile pushing [Y
power ON to enter INITIAL SET
MODE.
Y] or [Z
Z] several times to
w Push [Y
select the dial assignment item, “tOP.”
e Rotate [VOL] to select the condition.
[VOL] is assigned as
AF volume control.
qPush [A•FUNC] then [8•SET] to
enter SET MODE.
Y] or [Z
Z] several times to
wPush [Y
select the tuning step item.
[VOL]
].
PWR
ENT
BASIC OPERATION
■ Setting audio/squelch level
■ Receive and transmit
D To set the audio level
q Push [PWR] for 1 sec. to turn the power ON.
w Adjust audio volume to the desired level.
e Set a frequency.
When a signal is received:
• Squelch opens and audio is emitted from the speaker.
• Signal indicator shows the relative signal strength level.
rPush [A•FUNC], then [9•H/M/L] to select output power between high, middle and low.
• “L” appears when low power is selected.
• “M” appears when middle power is selected.
• No indication appears when high power is selected.
t Push and hold [PTT] to transmit, then speak into the microphone.
• “$” appears.
• Do not hold the microphone too close to your mouth or
speak too loudly. This may distort the signal.
y Release [PTT] to receive.
Rotate [VOL] to set the desired
audio level while receiving a signal.
[VOL]
• When no signal is received, push
and hold [MONI] while setting the
audio level.
• When [VOL] is assigned as tuning
Y]/[Z
Z] to adjust the audio
dial, push [Y
output level. (pgs. 14, 63)
D To set the squelch level
While pushing [MONI], push
Y]/[Z
Z] to set the squelch level.
[Y
• The squelch level “1” is loose
squelch, “10” is tight squelch.
• When [VOL] is assigned as tuning
dial, rotate [VOL] while [MONI] is
pushed. (pgs. 14, 63)
✔ For your information— Monitor function:
MONI
Push and hold [MONI] to listen to weak signals that do not
open the squelch.
15
4
BASIC OPERATION
■ Display type
USING
INITIAL SET MODE
The transceiver has 3 display types to suit your operating
style.
The display type is selected in INITIAL SET MODE (p. 63).
“Frequency Indication” type
Displays operating frequency.
“Channel Number Indication” type
“Channel Name Indication” type
Displays memory channel name you have assigned. In this
display pre-programmed memory channel names are displayed.
VFO mode is selectable.
• Programmed frequencies are indicated pre-programmed in the
selected memory channel.
• Push and hold [MONI] to display the operating frequency.
■ Key lock function
Displays memory channel number. In this type only preprogrammed memory channel numbers are displayed.
VFO mode cannot be selected.
• When the channel indication type is selected, only the following
functions can be performed.
- Scan function (p. 28)
- Output power setting (p. 15)
- DTMF memory function (p. 26)
- Key lock function (see right content)
- Scan pause timer setting, function key timer setting and LCD
backlight setting in SET MODE (p. 59)
16
The key lock function prevents accidental frequency changes
and function activation.
Push [A•FUNC] then push [✱•ENT
for 1 sec. to toggle the function ON and
OFF.
• “ ” appears while the lock function is
activated.
• [PWR], [PTT], [VOL] and [MONI] can
be operated regardless of this setting.
FUNC
ENT
5
REPEATER OPERATION
■ General
When using a repeater, the transmit frequency is shifted from
the receive frequency by the offset frequency. It is convenient
to program repeater information into memory channels.
q Set the receive frequency (repeater output frequency).
wPush [A•FUNC] and [4•DUP] several times to select “–” or
“+.”
• “–” indicates the transmit frequency is shifted down; “+” indicates
the transmit frequency is shifted up.
• Blinking “–” or “+” indicates the reversed duplex mode is selected
in SET MODE (p. 58).
ePush [A•FUNC] and [1•TONE] several times to activate the
subaudible tone encoder, if required.
• “ ” appears.
• Select the desired subaudible tone frequency, if necessary.
(p. 18)
r Push and hold [PTT] to transmit.
• The displayed frequency automatically changes to the transmit
frequency (repeater input frequency).
• If “OFF” appears, check the offset frequency (see right content
for details) and direction.
t Release [PTT] to receive.
yPush and hold [MONI] to check whether the other station’s
transmit signal can be directly received or not.
About reversed duplex mode
When the reversed duplex mode is selected, the receive frequency shifts. (Transmit frequency shifts in normal duplex
mode.)
Each receive and transmit frequency is shown in the table
below with the following conditions;
IC-V82: Input freq.-145.30 MHz, Direction-negative, Offset frequency-0.6 MHz
IC-U82: Input freq.-439.80 MHz, Direction-negative, Offset frequency-5 MHz
IC-V82
IC-U82
Reversed
OFF
ON
OFF
ON
Rx freq. 145.30 MHz 144.70 MHz 439.80 MHz 434.80 MHz
Tx freq. 144.70 MHz 145.30 MHz 434.80 MHz 439.80 MHz
■ Offset frequency
USING
SET MODE
When communicating through a repeater, the transmit frequency is shifted from the receive frequency by an amount
determined by the offset frequency.
q Push [A•FUNC], then push [8•SET] to enter SET MODE.
Y] or [Z
Z] several times until “±” and offset frequency
wPush [Y
appear.
eRotate [VOL] to select the desired offset frequency.
• Selectable steps are the same as the pre-set tuning steps.
• The unit of the displayed offset frequency is “MHz.”
rPush [✱•ENT ] (or [D•CLR]) to fix the offset frequency and
exit SET MODE.
17
5
REPEATER OPERATION
■ Subaudible tones
USING
SET MODE
D Tone information
Some repeaters require another tone system to be accessed.
Some repeaters require subaudible tones to be accessed.
Subaudible tones are superimposed over your normal signal
and must be set in advance.
qPush [A•FUNC], then push [8•SET] to enter SET MODE.
Y] or [Z
Z] one or more times until “rt” appears.
wPush [Y
DTMF TONES
While pushing [PTT], push the desired DTMF keys (0–9,
[A•FUNC], [B•CALL], [C•MR], [D•CLR], [#•BANK] and
[✱•ENT ]) to transmit DTMF tones.
• [✱•ENT
] transmits as “E”, [#•BANK] transmits as “F.”
• The transceiver has 16 DTMF memory channels (p. 26).
e Rotate [VOL] to select the desired subaudible tone.
rPush [✱•ENT ] (or [D•CLR]) to fix the selected tone and
exit SET MODE.
• Available subaudible tone frequencies
67.0
69.3
71.9
74.4
77.0
79.7
82.5
18
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
(unit: Hz)
210.7
218.1
225.7
229.1
233.6
241.8
250.3
254.1
1750 Hz TONE
Y] or [Z
Z] to transmit a 1750 Hz
While pushing [PTT], push [Y
tone signal.
✔ Convenient
Tone scan function: When you don’t know the subaudible
tone used for a repeater, the tone scan is convenient for detecting the tone frequency.
Push [A•FUNC], then push [3•T.SCAN] to start the tone scan.
• Push [D•CLR] to cancel the scan.
• When the required tone frequency is detected, the scan
pauses.
REPEATER OPERATION
■ Auto repeater function
(USA version only)
USING
■ Repeater lockout
INITIAL SET MODE
The USA version automatically activates the repeater settings
(duplex, ON/OFF, duplex direction, tone encoder ON/OFF)
when the operating frequency falls within or outside of the
general repeater output frequency range. The offset and repeater tone frequencies are not changed by the auto repeater
function. Reset these frequencies, if necessary.
Y] and [Z
Z], turn the power ON to enter INIq While pushing [Y
TIAL SET MODE.
Y] or [Z
Z] several times until “RPt” appears.
w Push [Y
e Rotate [VOL] to select the desired condition.
• “OF”— the auto repeater function is turned OFF;
• “R1”— the auto repeater function activates for duplex only;
• “R2”— the auto repeater function activates for duplex and tone.
USING
INITIAL SET MODE
This function helps prevent interference to other stations by
inhibiting your transmission when a signal is received. The
transceiver has two inhibiting conditions, repeater and busy.
Y] and [Z
Z], turn the power ON to enter INIq While pushing [Y
TIAL SET MODE.
Y] or [Z
Z] several times until “RLO” appears.
w Push [Y
e Rotate [VOL] to turn the repeater lockout function to “RP,”
“bU” or OFF.
• “RP”: Transmit is inhibited when a signal with un-matched subaudible tone is received.
• “bU”: Transmit is inhibited when a signal is received.
r Push [✱•ENT
r Push [✱•ENT
] (or [D•CLR]) to exit INITIAL SET MODE.
] (or [D•CLR]) to exit INITIAL SET MODE.
• Frequency range and offset direction
Frequency range
Duplex direction
145.200–145.495 MHz
“–” appears
146.610–146.995 MHz
147.000–147.395 MHz
“+” appears
442.000–444.995 MHz
“+” appears
447.000–449.995 MHz
“–” appears
19
6
MEMORY/CALL OPERATION
■ General description
■ Selecting a memory channel
The transceiver has 207 memory channels including 6 scan
edge memory channels (3 pairs), and 1 call channel. Each of
these channels can be individually programmed with operating frequency (pgs. 13, 14), duplex direction (p. 17) and offset
(p. 17), subaudible tone encoder or tone squelch and its tone
frequency (pgs. 18, 33) and skip information* (p. 30).
In addition, a total of 10 memory banks, A to J, are available
for usage by group, etc.
q Push [C•MR] to select memory mode.
*except for scan edge memory channels.
• “X” appears.
Push
MR
wEnter 2 digits to select the desired memory channel (or
Y]/[Z
Z] keys).
push the [Y
• The memory channels 0–9 are proceeded by a “0.”
• When [VOL] is assigned as tuning dial, rotate [VOL] to select
the memory channel. (pgs. 14, 63)
Push
TONE
P.BEEP
■ Selecting the call channel
➥ Push [B•CALL] to select the call channel.
• “C” is displayed instead of the memory channel number.
• Push [D•CLR] or [C•MR] to select VFO or memory mode, respectively.
Push
CALL
“C” appears
20
MEMORY/CALL OPERATION
■ Programming the memory/call channels
qPush [D•CLR] to select VFO mode, if necessary.
w Set the desired frequency.
eSet other information, such as tone, duplex, as desired.
rPush [A•FUNC], then [C•MR] momentarily.
• “X” and memory channel number blink.
MONI
FUNC
CALL
MR
TONE
DUP
PRIO
P.BEEP
SCAN
SET
T.SCAN
SKIP
H/M/L
MONI
FUNC
PWR
CLR
yPush [A•FUNC], then push [C•MR] for 1 sec. (until 3 beeps
are emitted) to program the information into the selected
memory channel and return to VFO.
FUNC
TONE
DUP
BANK
MR
PRIO
CALL
P.BEEP
SCAN
SET
MR
T.SCAN
SKIP
H/M/L
PWR
CLR
BANK
FUNC
MR
OPT
ENT
OPT
ENT
• Continue to hold [C•MR] down for 1 sec. after 3 beeps are emitted, to increment the displayed memory channel number.
Y] or [Z
Z] to select the desired memory channel.
tPush [Y
• When programming the call channel, select “C.”
• When [VOL] is assigned as tuning dial, rotate [VOL] to select
the memory channel. (pgs. 14, 63)
MONI
FUNC
CALL
MR
TONE
DUP
PRIO
P.BEEP
SCAN
SET
T.SCAN
SKIP
H/M/L
PWR
CLR
BANK
OPT
ENT
MONI
FUNC
TONE
CALL
P.BEEP
MR
T.SCAN
DUP
SCAN
SKIP
PRIO
SET
H/M/L
PWR
CLR
BANK
OPT
ENT
21
6
MEMORY/CALL OPERATION
■ Channel name programming
■ Memory transferring
qSelect a “Channel Name Indication” type in
MODE (p. 63).
wPush [C•MR] to select memory
mode, if necessary.
ePush [A•FUNC], then push [8•SET]
to enter into the channel name
programming mode.
This function transfers a memory channel’s contents to VFO
(or another memory/call channel). This is useful when searching for signals around a memory channel frequency and for
recalling the offset frequency, subaudible tone frequency etc.
INITIAL SET
[VOL]
D Memory/call ➾ VFO
• The character to be edited blinks.
rRotate [VOL] to select a character.
MR
FUNC
ENT
SET
Y] to move to the right, [Z
Z] to move to the left.
tPush [Y
• Up to 5 characters can be used for channel name.
• Usable characters are A–Z, 0–9, “space,” +, –, =, ✱, /, [, ] and :.
y Push [✱•ENT ] (or [D•CLR]) to fix and exit the channel
name programming mode.
22
qSelect the memory (call) channel
to be transferred:
➥ Push [C•MR] or [B•CALL] to select memory (call) mode.
Y] or [Z
Z] to select the
➥ Push [Y
memory channel.
• When [VOL] is assigned as tuning
dial, rotate [VOL] to select the
memory channel. (pgs. 14, 63)
wPush [A•FUNC], then push [C•MR]
for 1 sec. to transfer the selected
memory contents to the VFO.
• VFO mode is selected automatically.
MR
CALL
FUNC
6
MEMORY/CALL OPERATION
D Memory/call ➾ call/memory
D Clearing a memory
qSelect the memory (call) channel
to be transferred:
➥ Push [C•MR] or [B•CALL] to select the memory (call) mode.
Y] or [Z
Z] to select the
➥ Push [Y
memory channel.
qPush [A•FUNC], then push [C•MR]
to enter the memory transfer
mode.
• When [VOL] is assigned as tuning
dial, rotate [VOL] to select the
memory channel. (pgs. 14, 63)
wPush [A•FUNC], then push [C•MR]
momentarily.
• “X” and a memory channel number blink.
MR
CALL
FUNC
• “--” and “X” blink.
Y] or [Z
Z] to select the target memory.
ePush [Y
• When [VOL] is assigned as tuning dial, rotate [VOL] to select
the target channel. (pgs. 14, 63)
r Push [A•FUNC], then push [C•MR] for 1 sec.
• Memory mode is selected and the contents are transferred to the
target memory.
Y] or [Z
Z] to select the
wPush [Y
memory channel to be cleared.
• When [VOL] is assigned as tuning
dial, rotate [VOL] to select the memory channel. (pgs. 14, 63)
• The call channel cannot be cleared.
MR
FUNC
ePerform the following operation within 1.5 sec, otherwise
the memory clearing is cancelled and the transceiver returns to the memory mode.
- Push [A•FUNC], then push [C•MR] momentarily.
- Push [A•FUNC], then push [C•MR] for 1 sec.
• The contents of the selected memory are cleared.
r Push [D•CLR] to return to regular operation.
23
6
MEMORY/CALL OPERATION
■ Memory bank selection
■ Memory bank setting
The IC-V82/U82 has a total of 10 banks (A to J). Regular
memory channels, 0 to 199, are assigned into the desired
bank for easy memory management.
q Push [C•MR] to select memory mode, then select the deY] or [Z
Z].
sired memory channel via [Y
Push
q Push [C•MR] to select memory mode.
Push
MR
w Push [A•FUNC] and [#•BANK] to select memory bank condition.
[VOL]
MR
w Push [A•FUNC] and [8•SET] to enter
SET MODE.
Y] or [Z
Z] several times until
e Push [Y
“bAk” appears.
[VOL]
• “– –” indication blinks as follows.
• Bank initial blinks.
FUNC
e Rotate [VOL] to select the desired
bank, A to J.
• Banks that have no programmed contents are skipped.
r Push [✱•ENT
the bank.
FUNC
ENT
SET
BANK
ENT
] (or [D•CLR]) to set
• Initial stops blinking.
Y] or [Z
Z] to select the contents in the bank.
t Push [Y
• No channel numbers are displayed for memory bank operation.
y To return to regular memory condition, push [A•FUNC] and
[#•BANK] to enter memory bank condition, then push
[✱•ENT ] (or [D•CLR]).
24
r Rotate [VOL] to select the desired
bank to be set.
t Push [✱•ENT ] (or [D•CLR]) to set the channel into the
bank and return to regular memory condition.
y Repeat steps q to t to set another memory channel into
the same or another bank.
6
MEMORY/CALL OPERATION
■ Transferring bank contents
Contents of programmed memory banks can be cleared or
transferred to another bank.
INFORMATION: Even if the memory bank contents are
cleared, the memory channel contents still remain programmed.
w Push [A•FUNC] and [8•SET] to enter
SET MODE.
Y] or [Z
Z] several times until
e Push [Y
“bAk” appears.
• Bank initial appears.
q Select the desired bank contents to be transferred or erased.
➥ Push [C•MR] to select memory mode.
➥ Push [A•FUNC] and [#•BANK], then
rotate [VOL] to select the desired
memory bank.
[VOL]
[VOL]
FUNC
r Rotate [VOL] to select the desired
bank initial to transfer or erase.
• Select “– –” indication when erasing the
contents from the bank.
ENT
SET
t Push [✱•ENT ] (or [D•CLR]) to transfer or erase, and return to regular memory condition.
y Repeat steps q to t for transferring or erasing an another banks contents.
• Bank initial blinks.
FUNC
➥ Push [✱•ENT
] (or [D•CLR]) to
Y] and
select the bank then push [Y
Z] to select the desired contents.
[Z
BANK
ENT
• Bank initial stops blinking.
25
7
DTMF MEMORY
■ Programming a DTMF code
The transceiver has 16 DTMF memory channels (d0 to dF)
for storage of often-used DTMF codes of up to 24 digits.
qPush [A•FUNC], then push [0•OPT] to enter
MODE.
OPTION SET
• Rotate [VOL] to select “dtm.OF,” if necessary.
Push
FUNC
tPush the digit keys, [A•FUNC], [B•CALL], [C•MR], [D•CLR],
[#•BANK] and [✱•ENT ] to enter the desired DTMF code.
• A maximum of 24 digits can be input.
• [✱•ENT
] enters as “E”, [#•BANK] enters as “F.”
• If a digit is mistakenly input, push [MONI] or [PTT] momentarily
then repeat from step q.
FUNC
OPT
wPush [0•OPT] for 1 sec. to enter the DTMF memory.
• One of “d0” to “dF” appears.
OPT
T.SCAN
DUP
• “_ _ _ _ _” appears.
• Programmed memories can be cleared in this way.
OPT
SET
SKIP
H/M/L
BANK
OPT
ENT
yPush [MONI] or [PTT] to fix the digits and exit the DTMF
programming mode.
• Programmed DTMF codes sound when [MONI] is pushed.
The DTMF memory consists of 5 pages that are 1st to 5th, 6th to
10th, 11th to 15th, 16th to 20th and 21st to 24th digits.
1st page indication
2nd page indication
4th page indication
5th page indication
3rd page indication
for 1 sec.
Appears
26
SCAN
CLR
for 1 sec.
eRotate [VOL] to select the desired channel.
rPush [0•OPT] for 1 sec. to enter the DTMF programming
mode.
Push
P.BEEP
MR
TONE
PRIO
Push
CALL
Appears
Blinks
7
DTMF MEMORY
■ Transmitting a DTMF code
■ DTMF transmission speed
D Using a DTMF memory channel
qPush [A•FUNC], then push [0•OPT] to enter
MODE.
USING
OPTION SET
• Rotate [VOL] to select “dtm.OF,” if necessary.
Push
FUNC
OPT
wPush [0•OPT] for 1 sec. to enter the DTMF memory.
Push
OPT
for 1 sec.
e Rotate [VOL] to select the desired channel.
r Push [MONI] or [PTT] to exit the DTMF memory mode.
tWhile pushing [PTT], push [MONI] to transmit the selected
DTMF memory.
INITIAL SET MODE
When slow DTMF transmission speeds are required with
DTMF memory transmission (as for some repeaters), the
transceiver’s rate of DTMF transmission can be adjusted.
Y] and [Z
Z], turn the
qWhile pushing [Y
power on to enter INITIAL SET MODE.
Y] or [Z
Z] several times until
wPush [Y
“dtd” appears.
eRotate [VOL] to select the desired
DTMF transmission speed.
• Four speeds are available: “1” (100
msec. intervals) is the fastest; “5” (500
msec. intervals) is the slowest.
[VOL]
PWR
ENT
• After the DTMF code is transmitted, the transceiver returns to receive automatically.
rPush [✱•ENT
] to exit INITIAL SET MODE.
D Manual DTMF code transmission
While pushing [PTT], push digit keys, [A•FUNC], [B•CALL],
[C•MR], [D•CLR], [#•BANK] and [✱•ENT ] to transmit a DTMF
code manually.
• [✱•ENT
] transmits as “E”, [#•BANK] transmits as “F.”
27
8
SCAN OPERATION
■ Scan types
■ Programmed scan
Programmed scan repeatedly scans between two user programmed frequencies (memory channels “1A–3A” and
“1b–3b”) or scans between upper and lower band edges. This
scan is useful for checking for signals within a specific frequency range such as repeater output frequencies, etc.
Scans between lower (start) and high (stop) frequency.
PROGRAMMED SCAN
Band
edge
Start
1A
2A
3A
End
1b
2b
3b
Scan edges
Band
edge
Scan
Jump
Programmed scan P1 scans between 1A and 1b, P2 scans between 2A and 2b, and P3 scans between 3A and 3b frequencies.
MEMORY (SKIP) SCAN
Mch 1
Mch 2
Mch 3
Mch 4
SKIP
Mch 0
Mch 199
Mch 10
Mch 5
Mch 6
SKIP
Mch 9
Mch 8
Mch 7
PRIORITY WATCH
q Push [D•CLR] to select VFO mode, if necessary.
wPush [A•FUNC] and [5•SCAN] to start the scan, then a selected scan edge appears as “P1,” “P2,” “P3” or “AL.”
• To change the scan edge, push [A•FUNC] and [8•SET] several
times until the desired scan edge appears.
• “AL” for full scan, “P1”, “P2” and “P3” for programmed scan between the programmed scan edge channels as “1A”–“1b,”
“2A”–“2b” and “3A”–“3b.”
Y] or [Z
Z].
• To change the scan direction, push [Y
• When [VOL] is assigned as tuning dial, rotate [VOL] to change
the scan direction. (pgs. 14, 63)
Priority memory channel watch
VFO frequency
145.20 MHz
5 sec.
Mch 3
SCAN
Memory
scan
Mch 1
50 msec.
e Push [D•CLR] to stop the scan.
Mch 3
Mch 2
28
FUNC
50 msec.
Priority memory channel scan
VFO frequency
145.20 MHz
5 sec.
Push
Priority channel
Mch 4
Mch 5
Priority channel
Mch 199
Mch 6
SKIP
SCAN OPERATION
NOTE: Scan edges, 1A–3A/1b–3b, must be programmed
in advance. Program them in the same manner as regular
memory channels. (p. 21)
If the same frequencies are programmed into the scan
edges, programmed scan will not proceed.
■ Memory scan
Memory scan repeatedly scans all programmed memory
channels, except those set as skip channels.
q Push [C•MR] to select memory mode, if necessary.
• “X” appears.
w Push [A•FUNC] and [5•SCAN] to start the scan.
Y] or [Z
Z].
• To change the scan direction, push [Y
• When [VOL] is assigned as tuning dial, rotate [VOL] to change
the scan direction. (pgs. 14, 63)
MONI
FUNC
TONE
DUP
PRIO
CALL
P.BEEP
SCAN
SET
MR
T.SCAN
SKIP
H/M/L
PWR
Push
FUNC
SCAN
CLR
BANK
OPT
e Push [D•CLR] to stop the scan.
ENT
• Bank scan —Select the desired bank at above step q.
q Push [A•FUNC] and [#•BANK] to select memory bank condition.
w Rotate [VOL] to select the desired bank, A to J.
e Push [✱•ENT ] (or [D•CLR]) to set the bank.
29
8
SCAN OPERATION
■ Skip channels
■ Priority watch
In order to speed up the scan interval, you can set memory
channels you don’t wish to scan as skip channels.
Priority watch checks for signals on “priority channels” while
operating on a VFO frequency.
q Push [C•MR] to select memory mode, if necessary.
• “X” appears.
w Select a memory channel to set as a skip channel.
ePush [A•FUNC] and [6•SKIP] to toggle the skip setting ON
and OFF.
D Memory or call channel watch
While operating on a VFO frequency, memory or call channel
watch monitors for signals in the selected memory or call
channel every 5 sec.
• “SKIP” appears when the channel is set as a skip channel.
Push
FUNC
q Select the desired memory channel or the call channel.
w Push [D•CLR] to select VFO mode.
e Push [A•FUNC], then push [7•PRIO] to start watching.
SKIP
“SKIP” appears
• VFO is displayed, then the decimal point “.”, on the frequency
readout blinks.
• The priority channel is monitored every 5 sec.
• When the signal is detected on the priority channel, the watching
is paused according to the setting of the scan resume condition.
VFO frequency
5 sec.
Memory channel
50 msec.
r Push [D•CLR] to stop watching.
30
SCAN OPERATION
D Memory scan watch
While operating on a VFO frequency or the call channel, memory scan watch monitors for signals in each memory channel
in sequence, every 5 sec.
q Push [C•MR] to select memory mode, if necessary.
• “X” appears.
wPush [A•FUNC], then push [5•SCAN] to start the memory
scan.
e Push [A•FUNC], then push [7•PRIO] to start the watching.
• VFO is displayed, then the decimal point “.”, on the frequency
readout blinks.
• When the signal is detected on the priority channel, the watching
is paused according to the setting of the scan resume condition.
VFO frequency
Mch 3
Mch 2
Memory
scan
Mch 1
Mch 4
Mch 5
Priority channel
5 sec.
Mch 199
Mch 6
50 msec.
r Push [D•CLR] to stop the watching.
■ Scan resume condition
USING
SET MODE
When a signal is received during scanning, the scan resume
condition determines what action the transceiver takes. The
transceiver has 2 scan resume conditions available as
illustrated below. Use SET MODE to select the one which best
suits your needs.
q Push [A•FUNC], then push [8•SET] to enter SET MODE.
Y] or [Z
Z] several times until “SCP” or “SCt” apwPush [Y
pears.
e Rotate [VOL] to select the desired scan resume condition.
• Pause scan:
When receiving a signal, scan pauses on
the signal until it disappears. Resumes
2 sec. after the signal disappears.
SKIP
• Timer scan:
When receiving a signal, scan pauses on
the signal for 5 sec., 10 sec. or 15 sec.,
then resumes.
r Push [✱•ENT
Pause scan
Timer scan
] (or [D•CLR])to set and exit SET MODE.
31
9
SUBAUDIBLE TONES
■ Tone squelch
D Operation
The tone squelch opens only when receiving a signal containing a matching subaudible tone. You can silently wait for
calls from group members using the same tone.
q Set the operating frequency.
• Set the AF and squelch to the desired level as the normal operation.
w Set the desired subaudible tone in SET MODE.
• See page 32 for programming.
• Recommended CTCS frequencies
e Push [A•FUNC], then push [1•TONE].
• Repeat several times until “ ” appears when selecting CTCSS,
or “ D ” appears when selecting DTCS.
Push
FUNC
TONE
CTCSS
67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
(Unit: Hz)
156.7
162.2
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
DTCS
r When the received signal includes a matching tone,
squelch opens and the signal can be heard.
• When the received signal’s tone does not match, tone squelch
does not open, however, the S-indicator shows signal strength.
• To open the squelch manually, push and hold [MONI].
t Operate the transceiver in the normal way.
y To cancel the tone squelch, push [A•FUNC] and [1•TONE].
• Repeat several times until “ ” or “ D ” disappears.
32
NOTE: The transceiver has 50 tone frequencies and consequently their spacing is narrow compared to units having
38 tones. Therefore, some tone frequencies may receive
interference from adjacent tone frequencies.
To prevent interference from adjacent tone frequencies,
using the frequencies as in the following table, is recommended.
• Recommended DTCS codes
023
025
026
031
032
043
047
051
054
065
071
072
073
074
114
115
116
125
131
132
134
143
152
155
156
162
165
172
174
205
223
226
243
244
245
251
261
263
265
271
306
311
315
331
343
346
351
364
365
371
411
412
413
423
431
432
445
464
465
466
503
506
516
532
546
565
606
612
624
627
631
632
654
662
664
703
712
723
731
732
734
743
754
SUBAUDIBLE TONES
D Setting subaudible tones for tone squelch operation
Separate tone frequencies can be set for tone squelch operation rather than repeater operation (the same range of tones
is available— see right below). Like the repeater tones, these
are set in SET MODE.
When SET MODE is selected from memory mode.
y Push [A•FUNC], then push [C•MR] for 1 sec. to transfer the
contents to VFO.
q Select VFO or memory channel.
w Push [A•FUNC], then push [8•SET] to enter SET MODE.
Y] or [Z
Z] several times until “Ct” appears when see Push [Y
lecting CTCSS, or “dt” appears when selecting DTCS.
u Push [A•FUNC], then push [C•MR] for 1 sec.
• “ ” blinks when selecting CTCSS, or “ D ” blinks when selecting
DTCS.
• 3 beeps are emitted.
• VFO mode is selected automatically.
• 3 beeps are emitted.
Steps y and u are necessary when overwriting the memory
contents permanently. The set tone frequency is used for
temporary operation only, therefore, these steps are not necessary.
• Available CTCSS tone frequency list
r Rotate [VOL] to select the desired subaudible tone.
t Push [✱•ENT ] (or [D•CLR]) to program the selected tone
and exit SET MODE.
67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
(unit: Hz)
210.7
218.1
225.7
229.1
233.6
241.8
250.3
254.1
33
9
SUBAUDIBLE TONES
■ Pocket beep operation
This function uses subaudible tones for calling and can be
used as a “common pager” to inform you that someone has
called when you were away from the transceiver.
D Waiting for a call from a specific station
t When a signal with the matched tone is received, the
transceiver emits beep tones and blinks “ .”
• Beep tones sound for 30 sec. and “ ” blinks. To stop the beeps
manually, push any key. “ ” continues blinking until step y is
operated.
q Set the operating frequency.
w Set the desired CTCSS tone frequency or DTCS code in
SET MODE.
CTCSS
• See p. 33 for programming details.
e Push [A•FUNC], then push [1•TONE].
• Repeat several times until “ ” appears when CTCSS, or “ D ” appears when DTCS is selected.
Push
FUNC
TONE
CTCSS
DTCS
r Push [A•FUNC], then push [2•P.BEEP] to activate the pocket
beep function.
• “ ” appears.
Push
FUNC
P.BEEP
CTCSS
34
DTCS
DTCS
y Push [PTT] to answer.
• “ ” disappears and cancels the pocket beep function automatically.
SUBAUDIBLE TONES
■ Tone scan
By monitoring a signal that is being operated with a repeater,
pocket beep or tone squelch function, you can determine the
tone frequency necessary to access a repeater or open the
squelch.
q Set the frequency to be checked for a tone frequency or
code.
w Push [A•FUNC], then push [1•TONE].
• Repeat several times to select the tone condition or type to be
scanned. (One of “ ,” “ ” or “ D ” appears)
• The tone scan can be operated even if the tone condition or type
is not selected.
Push
FUNC
TONE
r When the CTCSS tone frequency or DTCS code is
matched, the squelch opens and the tone frequency or
code is temporarily programmed into the selected mode
such as memory or call channel.
• The tone scan pauses when a CTCSS tone frequency or 3-digit
DTCS code is detected.
• The decoded CTCSS tone frequency or 3-digit DTCS code is
used for the tone encoder or tone encoder/decoder depending
on the selected tone condition or type in step w.
- No indication : Cannot be used for operation.
-“ ”
: CTCSS tone encoder
-“ ”
: CTCSS tone encoder/decoder
- “D ”
: DTCS tone encoder/decoder
t Push [D•CLR] to stop the scan.
e Push [A•FUNC], then push [3•T.SCAN] to start the tone
scan.
Y] or [Z
Z].
• To change the scanning direction, push [Y
Push
FUNC
T.SCAN
35
10
PAGER/CODE SQUELCH
Required Optional UT-108
■ Pager function
■ Code programming
This function uses DTMF codes for paging and can be used
as a “message pager” to confirm you of a caller’s identification
even when you leave the transceiver temporarily unattended.
D Before programming
Pager selective code (push [PTT])
Beep
Beep Beep
Answer back (manual)
The pager and code squelch functions require ID codes and a
group code. These codes are 3-digit DTMF codes and must
be written into the code channels before operation.
q Decide the ID code of each transceiver and a group code
for your group.
w Decide whether you want to return to normal operation or
code squelch operation after a connection is made.
e Program the ID code, group code and transmit codes
(other station’s codes) as below.
D Code channel assignment
ID OR
CODE CHANNEL
GROUP CODE
NUMBER
eep
p B
Bee Beep
Set both transceivers to either
code squelch or non-coded operation
“RECEIVE ACCEPT” OR
“RECEIVE INHIBIT”
Your ID code
“Receive accept” only
Other parties’
ID code
1–6
“Receive inhibit” should be
programmed in each channel.
One of 1–6
“Receive accept” must be
programmed.
“Receive inhibit” only.
Group code
Memory space*
*Channel CP automatically memorizes an ID code when receiving a
pager call. The contents in channel CP cannot be changed manually.
Communication
36
PAGER/CODE SQUELCH
10
D Code programming
An ID code MUST be programmed into code channel C0. Up
to 6 transmit codes are programmable into code channels, C1
to C6, if required.
q Push [A•FUNC], then push [0•OPT] to enter
MODE.
y Enter the desired 3-digit transmit code via the keypad.
OPTION SET
• Rotate [VOL] to select “dtm.PG” or “dtm.CS,” if “dtm.OF” appears.
or
u Push [A•FUNC], then push [6•SKIP] to set the channel for
“receive inhibit” or “receive accept.”
• When “receive inhibit” is set, “SKIP” appears as below.
• Code channel C0 cannot be set as “receive inhibit.”
• See the table for “receive accept” and “receive inhibit” details
(p. 36).
w Push [0•OPT] for 1 sec. to enter the code selection mode.
• One of either “CP” or “C0” to “C6” blinks.
• “C0” is the ID code and “C1” to “C6” are transmit codes.
10
i Repeat steps t and y to set additional transmit code
channels, if desired.
o Push [✱•ENT ] or [PTT] to exit CODE SET MODE.
Y]/[Z
Z]) to select code channel C0.
e Rotate [VOL] (or push [Y
• A different ID code must be programmed into each transceiver.
r Enter the desired 3-digit ID code via the keypad.
Y]/[Z
Z]) to select a transmit code
t Rotate [VOL] (or push [Y
channel from C1 to C6.
• Receive accept/receive inhibit
➥ “Receive accept” (“SKIP” indicator does not appear) accepts pager calls when the transceiver receives a signal
with a code the same as that in the code channel.
➥ “Receive inhibit” (“SKIP” indicator appears) rejects calls
even when the transceiver receives a code the same as
that in the code channel. Transmit codes should therefore
be programmed for “receive inhibit,” otherwise the transceiver will not reject unnecessary calls.
37
10
PAGER/CODE SQUELCH
■ Pager operation
D Calling a specific station
q Program the desired code channel in advance (p. 37).
w Set the operating frequency.
• Set the AF and squelch to the desired level as in normal operation.
e Push [A•FUNC], then push [0•OPT].
• Rotate [VOL] to select “dtm.PG,” if “dtm.CS” or “dtm.OF” appears.
u After confirming a connection, push [A•FUNC] and [0•OPT]
to enter OPTION SET MODE, then rotate [VOL] to select the
code squelch operation, or repeat the previous key
operation again to select non-selective calling system.
• DO NOT push any digit keys while code channels C0 to C6 are
displayed, or code channel contents will be changed.
i Communicate with the other party as normal: push [PTT]
to transmit; release to receive.
D Waiting for a call from a specific station
r Select the desired transmit code channel:
➥ Push [0•OPT] for 1 sec. to enter the code selection condition.
➥ Rotate [VOL] to select the desired code channel.
➥ Push [✱•ENT ] to return to previous condition.
• 100 MHz digit shows “P.”
t Push [PTT] to transmit the pager code.
y Wait for an answer back.
• When the transceiver receives an answer back code, the function display shows the other member’s ID or group code.
38
q Set the operating frequency.
w Push [A•FUNC], then push [0•OPT].
➥ Rotate [VOL] to select “dtm.PG,” if “dtm.CS” or
“dtm.OF” appears.
➥ Push [✱•ENT ] to return to previous condition.
• 100 MHz digit shows “P.”
e Wait for a call.
• When receiving a call, the caller’s ID or group code appears as
shown at next page.
• DO NOT push any digit keys while code channels C0 to C6 are
displayed, or code channel contents will be changed.
r Push [PTT] to send an answer back call and display the
operating frequency.
t After confirming a connection, push [A•FUNC] and [0•OPT]
to enter OPTION SET MODE, then rotate [VOL] to select the
code squelch operation, or repeat the previous key
operation again to select non-selective calling system.
PAGER/CODE SQUELCH
• PERSONAL CALLS
This display appears when you are called with your ID code
and the calling station’s ID code is 123.
“CP” and “
” blink.
• GROUP CALLS
This display appears when you are called with the group
code, 888, and 888 has been programmed into code channel
C6.
Code channel
• ERROR INFORMATION
When the transceiver receives an incomplete signal, “E” and
previously received code appear.
Previously received code.
Pager/code squelch operation during channel indication
To use these functions in channel indication, the pager/code
squelch setting must be programmed with other memory contents before selecting channel number indication.
10
■ Code squelch
Code squelch provides communications with quiet standby
since you will only receive calls from stations which know
your ID or group code. Each push of [PTT] sends a 3-digit
code in order to open the receiving station’s code squelch
prior to voice transmission.
q Set the operating frequency.
• Set the AF and squelch to the desired level as in normal operation.
w Push [A•FUNC], then push [0•OPT].
• Rotate [VOL] to select “dtm.CS,” if “dtm.PG” or “dtm.OF” appears.
e Select the desired transmit code channel:
➥ Push [0•OPT] for 1 sec. to enter code selection condition.
➥ Rotate [VOL] to select the desired code channel.
➥ Push [✱•ENT ] to exit CODE SET MODE and return to
previous condition.
10
• 100 MHz digit shows “C.”
r Operate the transceiver in the normal way (push [PTT] to
transmit; release [PTT] to receive).
t To cancel the code squelch, push [A•FUNC] and [0•OPT],
then rotate [VOL] to select “dtm.OF.”
• 100 MHz digit shows “1” when the function is cancelled.
39
11
DIGITAL MODE OPERATION
Required Optional UT-118
■ Digital mode operation
The IC-V82/U82 with optional digital unit UT-118 can be operated for digital voice mode and low-speed data operation
for both transmit and receive. Also available for connecting
GPS receiver (compatible with an RS-232C output/NMEA format/4800 bps) and transmit/receive position data.
w Push [0•OPT] for 1 sec. then rotate [VOL] to select the desired call sign channel.
Y] (or [Z
Z]) to set into call sign programming condition.
e Push [Y
■ Call sign programming
Four kind of call sign memories are available for your own call
sign “myC,” other station call sign “yUC” and nearest repeater
call sign “R1C” and another zone’s repeater call sign “R2C.”
Each call sign memory can be stored up to 6 call signs, and
each call sign programmed up to 8 characters.
• The 1st digit blinks and channel indication stops blinking.
r Rotate [VOL] to set the desired character or code.
Z] or [Y
Y] to move the cursor to left or right, respectively.
• Push [Z
Y] (or [Z
Z]) to select 2nd digit, then rotate [VOL] to
t Push [Y
set the desired character or code.
• 2nd digit blinks (1st digit stops blinking).
• Repeat this step for programming your call sign.
D Your call sign programming
Your call sign must be programmed for both Digital voice and
low-speed data communications (including GPS transmission).
q Push [A•FUNC] and [0•OPT] to enter OPTION SET MODE, then
Y] or [Z
Z] several times to select the call sign select
push [Y
mode.
• “myC” appears.
40
y Push [0•OPT] to fix the call sign.
u Rotate [VOL] to select an another channel from “C1” to
“C6.”
i Repeat steps w to u to program your call sign channels.
NOTE: All digital (DV) mode operation/settings are required an optional digital unit UT-118. The transceiver without UT-118 does not indicate any items for the digital (DV)
mode that described in this section.
DIGITAL MODE OPERATION
11
D Your call sign note programming
Your call sign can be added some information such as operating radio type, place or area. Call sign note can be stored
up to 6 type, and each call sign note programmed up to 4
characters.
Y] (or [Z
Z]) to select 2nd digit, then rotate [VOL] to
t Push [Y
set the desired character or code.
• 2nd digit blinks (1st digit stops blinking).
• Repeat this step for programming your call sign note.
q Push [A•FUNC] and [0•OPT] to enter OPTION SET MODE, then
Y] or [Z
Z] several times to select the call sign select
push [Y
mode.
• “myS” appears.
w Push [0•OPT] for 1 sec. then rotate [VOL] to select the desired call sign note channel.
y Push [0•OPT] to fix the call sign.
u Rotate [VOL] to select an another channel from “C1” to
“C6.”
i Repeat steps w to u to program your call sign channels.
11
Y] (or [Z
Z]) to set into call sign note programming
e Push [Y
condition.
• The 1st digit blinks and channel indication stops blinking.
r Rotate [VOL] to set the desired character or code.
Z] or [Y
Y] to move the cursor to left or right, respectively.
• Push [Z
41
11
DIGITAL MODE OPERATION
D Station call sign programming
Station call sign must be programmed for the specified station call as well as repeater operation in both Digital voice and
low-speed data communications.
q Push [A•FUNC] and [0•OPT] to enter OPTION SET MODE, then
Y] or [Z
Z] several times to select the call sign select
push [Y
mode.
Y] (or [Z
Z]) to select 2nd digit, then rotate [VOL] to
t Push [Y
set the desired character or code.
• 2nd digit blinks (1st digit stops blinking).
• Repeat this step for programming station call sign.
• “yUC” appears for station call sign.
w Push [0•OPT] for 1 sec then rotate [VOL] to select the desired call sign channel.
y Push [0•OPT] to fix the call sign.
u Rotate [VOL] to select an another channel from “C1” to
“C6.”
i Repeat steps w to u to program another station call sign
channels.
✔ For your information:
Y] (or [Z
Z]) to set into call sign programming condie Push [Y
tion.
• The 1st digit blinks and channel indication stops blinking.
r Rotate [VOL] to set the desired character or code.
Z] or [Y
Y] to move the cursor to left or right, respectively.
• Push [Z
42
Station and/or repeater call sign can be programmed from
Received call record when a call is received.
See page 45 for details.
DIGITAL MODE OPERATION
11
■ Digital voice mode operation
D When sending a CQ
q Set the desired frequency in VFO mode. (pgs. 13, 14)
• Select output power, if desired. (p. 15)
w Push [A•FUNC] then [0•OPT] for enter OPTION SET MODE,
Y] or [Z
Z] several times to select the digital sethen push [Y
lect mode.
• “DG” appears.
(continued from step t)
y Select “CQ” as the call sign.
Y] or [Z
Z] several times to select the call sign se- Push [Y
lect mode.
• “yUC” appears.
e Rotate [VOL] to turn the digital mode ON.
- Push [0•OPT] for 1 sec. then rotate [VOL] to select the desired channel.
- Push [0•OPT] for 1 sec. to set “CqCqCq.”
Appears
Y] once to select the your call sign select mode.
r Push [Y
• “myC” appears.
t Push [0•OPT] for 1 sec. then rotate [VOL] to select the desired your call sign channel, if you have programmed several call signs.
• After selecting the your call sign, push [0•OPT] to return to
TION SET MODE.
- Push [✱•ENT
] (or [D•CLR]) to exit OPTION SET MODE.
11
OP-
NOTE: In the digital mode operation; when “BUSY” indicator appears but no sound comes out the speaker, it
may be caused by the interference of FM mode. In this
case, to prevent interference of FM mode, set the digital
monitor setting (p. 47) to “An(analog)” then listen on the
channel before transmitting by pushing [MONI].
uPush and hold [PTT] to transmit and speak into the microphone at normal voice level.
• Transmit indicator appears and the RF meter shows the output power.
i Release [PTT] to return to receive.
• The other station call sign will be received.
• Received call signs can be stored into the received call record
automatically. See page 44 for details.
43
11
DIGITAL MODE OPERATION
D When calling the desired station
(continued from p. 43 step t)
y Select the desired call sign.
Y] or [Z
Z] several times to select the call sign select
- Push [Y
mode.
• “yUC” appears.
- Push [0•opt] then rotate [VOL] to select the desired call
sign (pre-programmed), or set the desired call sign. (see
p. 38)
■ When receiving a Digital call
When an individual station call is received, the calling station
call sign can be stored into the received call record.
The record is cleared once turning power OFF.
D Received call record
q Push [A•FUNC] then [0•OPT] for enter OPTION SET MODE,
Y] or [Z
Z] several times to select the received
then push [Y
call indication.
• “RXCALL,” “R1CALL,” and “R2CALL” are available for the received station call sign, repeater 1/2 call signs, respectively.
- Push [✱•ENT
] to exit OPTION SET MODE.
w To confirm the received call, push [0•OPT] for 1 sec. to
enter the received call sign indication mode.
uPush and hold [PTT] to transmit and speak into the microphone at normal voice level.
• Transmit indicator appears and the RF meter shows the output power.
i Release [PTT] to return to receive.
• The other station call sign will be received.
• Received call signs can be stored into the received call record
automatically. See page 42 for details.
44
DIGITAL MODE OPERATION
D To store a received call
q Push [A•FUNC] and [0•OPT] several times to select the call
sign select mode.
• “yUC” appears for station call sign.
• “R1C” or “R2C” appears for repeater call sign.
w Push [0•OPT] for 1 sec. to call sign indication, rotate [VOL]
to select the blank channel or erasable channel.
Y] or [Z
Z] several times to select
e Push [0•OPT] then, push [Y
the received call indication.
• “RXC.AL” appears for received station call sign.
• “R1C.AL” or “R2C.AL” appears for received repeater call sign.
r To confirm the received call, push [0•OPT] for 1 sec. to
enter the received call sign indication mode.
11
■ Break-in communication
The break-in function allows you to break into an another stations communications in both Digital voice and low-speed
data operation.
q While receiving another station communication, push
[A•FUNC] then [0•OPT] to enter OPTION SET MODE.
Y] or [Z
Z] several times to select the break-in setw Push [Y
ting, then turns the break-in setting ON.
• “bRk” appears.
eWhen both stations are in standby, transmit to send a
break-in call.
11
• Programmed call sign station receives the break-in call as well
as your call sign.
rWait for the reply call from the station who receive the
break-in call.
t After receive the reply call, communicate normal way.
yTo cancel the break-in, push [A•FUNC] and [0•OPT], then rotate [VOL] to turn OFF.
tPush [0•OPT] for 1 sec. to store the call sign into the selected station call sign channel or repeater call sign channel.
45
11
DIGITAL MODE OPERATION
■ EMR communication
■ Pocket beep operation
The EMR communication mode is available for Digital mode
operation. In the EMR call, no call sign setting is necessary.
This function uses a digital code/call sign for calling and can
be used as a “common pager” to inform you that someone
has called while you were away from the transceiver. The digital code or call sign squelch does not function while in a lowspeed data communication.
q Set the desired frequency then push [A•FUNC] and [0•OPT]
to enter OPTION SET MODE.
Y] or [Z
Z] several times to select the EMR setting,
w Push [Y
then turns the EMR setting ON.
• “EmR” appears.
D Waiting for a call from a specific station
q Set the operating frequency.
w Program the digital code or call sign in setting mode.
• See p. 51, “Digital code setting” or p. 40 “Call sign programming.”
eOperate the transceiver normal way.
rTo cancel the EMR communication mode, push [A•FUNC]
and [0•OPT] for 1 sec., then rotate [VOL] to turn OFF.
e Push [A•FUNC] and [1•TONE] one or more times until “ ”
or “ ” appears in the function display.
• “ ” for call sign squelch; “ ” for digital code squelch operation.
r Push [A•FUNC], then push [2•P.BEEP] to activate the pocket
beep function.
• “ ” appears.
t When a signal with the matched call sign/digital code is received, the transceiver emits beep tones and blinks “ .”
• Beep tones sound for 30 sec. and “ ” blinks. To stop the beeps manually, push any key. “ ” continues blinking until step y is operated.
y Push [PTT] to answer.
• “ ” disappears and cancels the pocket beep function automatically.
u To cancel the call sign/digital code squelch, push [A•FUNC]
and [1•TONE] one or more times until or “ ” or “ ” disappears.
46
DIGITAL MODE OPERATION
11
■ Digital squelch functions
■ Digital monitor
The digital code (CSQL) or call sign (DSQL) squelch opens
only when receiving a voice signal with the same pre-programmed digital code or call sign, respectively. The digital
code or call sign squelch does not function while in a lowspeed data communication.
This function is used to listen to the analog signal (FM mode
signal) without changing the operating mode while digital (DV
mode) operation.
q Set the operating frequency.
w Program the digital code or call sign in setting mode.
• See p. 51, “Digital code setting” or p. 40 “Call sign programming.”
e Push [1•TONE] one or more times until “ ” or “ ” appears
in the function display.
USING
INITIAL SET MODE
Y] and [Z
Z], turn the power ON to enter INIq While pushing [Y
TIAL SET MODE.
Y] or [Z
Z] several times until “dmO” appears.
w Push [Y
e Rotate [VOL] to turn the repeater lockout function to “RP,”
“bU” or OFF.
• “An”: Activate for monitoring the analog (FM mode) signals.
(default)
• “dG”: Activate to open the call sign or digital code squelch.
• “ ” for call sign squelch; “ ” for digital code squelch operation.
r When a signal with the matched call sign/digital code is received, the squelch opens and the signal can be heard.
• When the received signal includes an unmatched call sign/digital
code, the squelch does not open. However, the S-meter shows
the received signal strength.
• To open the squelch manually, push and hold [MONI].
t Operate the transceiver in the normal way (push [PTT] to
transmit; release [PTT] to receive).
y To cancel the call sign/digital code squelch, push [1•TONE]
one or more times until or “ ” or “ ” disappears.
r Push [✱•ENT
11
] (or [D•CLR]) to exit INITIAL SET MODE.
NOTE: When “digital monitor setting” is set to “An (analog),” the monitor function (pushing [MONI]) works as the
analog monitor for receiving an FM signal. Then digital
monitor function is activate using the Squelch control
Y] or [Z
Z]).
(pushing [MONI] and [Y
✔ While scanning in digital mode:
• The call sign squelch function deactivate, then after cancelling the scan it will activate again.
• Scan stops near channel in a 5 kHz tuning steps, and then
no sound comes out.
47
11
DIGITAL MODE OPERATION
■ Low-speed data communication
In addition to the digital voice communication, a low-speed
data communication is available (Refer p. 4 about the transceiver-PC connection details).
q Set the desired frequency.
wSet another settings, such as repeater call, transmit output
power.
e Push [A•FUNC] then [0•OPT] for enter OPTION SET MODE,
Y] or [Z
Z] several times to select the automatic
then push [Y
data transmission setting. (see p. 51)
• “AtX” appears.
• Skip this setting, if you want to transmit manually.
t Start up the low-speed data communication application.
ySet the application as follows.
• Port
: The same COM port number as transceiver’s
• Baud rate : 4800 bps or 9600 bps (same as step r)
• Data
: 8 bit
• Parity
: None
• Stop
: 1 bit
• Flow control: Xon/Xoff
uTransceiver automatically transmits or receives the data
while you sending data to transceiver. Or push and hold
[PTT] to transmit, release to receive the data manually.
• Refer to the instruction of the application that how to send or receive data.
Y] once to select the data communication speed
r Push [Y
setting. (see p. 52)
• “SPd” appears.
• Select suitable data speed for your PC or application.
48
DIGITAL MODE OPERATION
11
■ About D-STAR system
In the D-STAR system, repeater linking via a 10 GHz band
backbone and internet network (gateway connection) capabilities are available. This system allows you to much wider
coverage range during Digital voice mode operation.
• D-STAR system outline
Also, the D-STAR system repeaters are connectable through
the internet network— gateway connection capability.
10 GHz signal
Repeater A
Repeater B
440 MHz signal
440 MHz signal
Station A
Station B
Repeater D
Repeater C
440 MHz signal
Station C
For example, when station B uses the gateway connection
station B can communicate with the station C!
By using the gateway connection, long distance communication like DX operation may be possible with 144 MHz/440MHz
digital voice!
11
In the D-STAR system, independent repeater’s operating
area is called as Area and a group that linking repeaters via a
10 GHz backbone is called as Zone.
Internet
network
10 GHz signal
For current existing repeater operation, stations that are communicating must be in the same repeater’s operating area.
However, in the D-STAR system as in the illustration at left,
the repeaters can be linked via the system repeaters (with a
10 GHz signal). Thus stations A and B can communicate even
though they are in different repeater operating areas.
440 MHz
signal
NOTE: The digital repeater for IC-V82/U82 (144 MHz/440
MHz of amateur radio bands operation) is not available at
present of October 2004. It will be designed in the future.
Station D
49
11
DIGITAL MODE OPERATION
■ Repeater call sign programming
Repeater call sign must be programmed for the repeater operation in both Digital voice and low speed data communications.
q Push [A•FUNC] and [0•OPT] to enter OPTION SET MODE, then
Y] or [Z
Z] several times to select the call sign items.
push [Y
• “R1C” or “R2C” appears for repeater call sign.
w Push [0•OPT] for 1 sec. then rotate [VOL] to select the desired call sign channel.
y Push [0•OPT] to fix the call sign.
u Rotate [VOL] to select an another channel from “C1” to
“C6.”
i Repeat steps w to u to program another repeater call
sign channels.
✔ For your information:
Station and/or repeater call sign can be programmed from
Received call record when a call is received.
See page 45 for details.
✔ For your information:
Repeater call sign can be programmed gateway connection
capabilities at step r for connecting to the other Area or
Zone.
• “G” appears or disappears at the 8th digit when each pushing [8•SET].
Y] (or [Z
Z]) to set into call sign programming condie Push [Y
tion.
• The 1st digit blinks and channel indication stops blinking.
r Rotate [VOL] to set the desired character or code.
Z] or [Y
Y] to move the cursor to left or right, respectively.
• Push [Z
Y] (or [Z
Z]) to select 2nd digit, then rotate [VOL] to
t Push [Y
set the desired character or code.
• 2nd digit blinks (1st digit stop blinking).
• Repeat this step for programming repeater call sign.
50
While using the repeater 2 (other Area or Zone) system, the
repeater 2 setting must be selected ON in OPTION SET MODE.
• “R2C” (Repeater 2 call sign) can be programmed or used when
“RP2” (Repeater 2 setting) is set to ON (default).
DIGITAL MODE OPERATION
11
■ Other setting items
qPush [A•FUNC] and [0•OPT] to enter OPTION SET MODE, then
Y] or [Z
Z] several times to select the desired item.
push [Y
w Rotate [VOL] to select the desired value or condition.
D Digital Code
Sets the desired digital code for digital code squelch operation. Total of 100 codes (00–99) are available. (default: 00)
D Auto Reply
During Digital mode operation, auto reply function is available. This function replies to an individual station call even
you are away from the transceiver.
(default: OFF)
After the manual transmission (pushing [PTT]) or message
transmission, the Auto Reply setting is return to OFF automatically.
D Auto data Transmission
During low-speed data operation, auto data transmission
function is available. This function transmits when data are
input from PC via the [DATA] jack.
(default: OFF)
After the manual transmission (pushing [PTT]), the Auto
Transmission setting is return to OFF automatically.
11
51
11
DIGITAL MODE OPERATION
D Data Speed
D Auto RxCall Write
Select the communication speed between the transceiver and
PC from 4800 bps or 9600 bps.
(default: 9600)
When an individual station call is received, the calling station
call sign can be stored automatically. The stored call sign can
be re-called when selecting a station call sign.
(default: OFF)
D Standby Beep
Turns the beep emission capability when the communicating
station finishes transmitting or the receive signal disappears.
(default: OFF)
52
D Auto Rx RepeaterCall Write
When an individual station call via the repeater is received,
the repeater call sign can be stored automatically. The stored
repeater’s call sign can be re-called when selecting a repeater call sign.
(default: OFF)
DIGITAL MODE OPERATION
11
D Auto RxCall Display
D Message Transmission
When an individual station call is received, the calling station
call sign can be indicated automatically.
(default: ON)
Select the Message transmission function ON and OFF.
When ON is selected, transceiver transmits a text message
(pre-programmed).
(default: OFF)
After the transmission once, the Message Transmission setting is return to OFF automatically.
D Auto MyCALL Display
Sets auto MyCALL display function ON and OFF. When this
setting is set to ON, the transceiver automatically indicates
your programmed call sign at turning power ON or digital
mode transmission.
(default: OFF)
D TX message
TX messages are available up to 6 channels and each channel can be programmed up to 20 characters message. Available characters are 0 to 9, A to Z (capital letters only), some
symbols and space. (see the next page for details)
11
53
11
DIGITAL MODE OPERATION
D TX message programming
At least one of the TX message channels must be programmed, if you want to use the GPS message. The GPS
message is transmitted from TX message channels.
Y] (or [Z
Z]) to select “tXm,”
q While OPTION SET MODE, push [Y
then push [0•OPT] for 1 sec. to edit the message indication
then rotate [VOL] to select the message channel.
• One of either “C1” to “C6” blinks.
Y] to set into message programming condition.
w Push [Y
• Available characters
(space)
(!)
(”)
(#)
($)
(%)
(&)
(’)
(( )
( ))
(✱)
(+)
(,)
(–)
(.)
(/)
(0)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(:)
(;)
(<)
(=)
(>)
(?)
(@)
(A)
(B)
(C)
(D)
(E)
(F)
(G)
(H)
(I)
(J)
(K)
(L)
(M)
(N)
(O)
(P)
(Q)
(R)
(S)
(T)
(U)
(V)
(W)
(X)
(Y)
(Z)
([)
(\)
(])
(^)
• The 1st digit blinks and channel indication stops blinking.
e Rotate [VOL] to set the desired character.
Y] to select 2nd digit, then rotate [VOL] to set the
r Push [Y
desired character.
• 2nd digit blinks (1st digit stop blinking).
• Repeat this step for programming.
t Push [0•OPT] to set the message.
y Repeat steps w to t to set another message channels.
u Push [✱•ENT ] (or [D•CLR]) to exit OPTION SET MODE.
54
DIGITAL MODE OPERATION
11
■ GPS operation
The IC-V82/U82 can indicate the current position (Latitude and
Longitude) when a GPS receiver (compatible with an RS-232C
output/NMEA format/4800 bps) is connected to [DATA] jack. And
also can transmit the position data and message to other stations.
Y] twice to select the position indication.
rPush [Y
D Position indication
t Push [0•OPT] for 1 sec. to enter the position indication.
q While connecting a GPS receiver, push [A•FUNC] and
[0•OPT] to enter OPTION SET MODE.
Y] or [Z
Z] several times to select the GPS setting.
w Push [Y
• Latitude and longitude date appear in order as below.
• “GPS” appears.
Minutes
North or South Degrees
Seconds
Push
Push
11
e Rotate [VOL] to set the suitable sentence formatter for the
connecting GPS receiver.
• For your position indication is necessary to select “GGA” or “RMC.”
Seconds
Minutes
East or West Degrees
yAfter checking the current position, push [✱•ENT
[D•CLR]) to return to normal operating mode.
IMPORTANT: When set the sentence formatter at step e
• Sentence formatters
GLL
GGA
RMC
GSA
VTG
10
GLL, GGA 11
GLL, RMC 12
GLL, GSA 13
GLL, VTG 14
GGA, RMC 15
GGA, GSA
GGA, VTG
RMC, GSA
RMC, VTG
GSA, VTG
] (or
16
17
18
19
20
GLL, GGA, RMC
GLL, GGA, GSA
GLL, GGA, VTG
GLL, RMC, GSA
GLL, RMC, VTG
21
22
23
24
25
GLL, GSA, VTG
GGA, RMC, GSA
GGA, RMC, VTG
GGA, GSA, VTG
RMC, GSA, VTG
for connecting GPS receiver, and already programmed your
call sign, GPS automatic transmission is activate every 3
minutes. The automatic transmission can be changed interval time or deactivated, if desired. (see the next page)
55
11
DIGITAL MODE OPERATION
D GPS Automatic transmission
q While connecting a GPS receiver, push [A•FUNC] and
[0•OPT] to enter OPTION SET MODE.
Y] or [Z
Z] several times to select the GPS automatic
w Push [Y
transmission.
• “GtX” appears.
IMPORTANT: GPS Automatic transmission transmits at
every setting interval even while receiving an another stations communication. To prevent interfere the another stations, set the GPS transmission together with the Repeater
lockout item “RLO” (set to “bU” busy lockout) in INITIAL SET
MODE. (p. 62)
D Receiving a GPS transmission
e Rotate [VOL] to set the interval time for the GPS automatic transmission.
• Interval time is selectable from 0.5 (30 sec.), 1, 3, 5, 10, 30 min.
q Push [A•FUNC] and [0•OPT] to enter OPTION SET MODE.
Y] or [Z
Z] several times to select the received posiw Push [Y
tion.
• “RXP.OS” appears.
Y] three times to select the transmit message serPush [Y
lection, if desired.
• GPS TX message is selectable from OFF and C1 to C6.
• TX message must be programmed in advance. (see page 50 for
setting)
e Push [0•OPT] for 1 sec. to enter the position indication.
Y]
• Latitude data and longitude date appear by every pushing [Y
Z].
or [Z
Y] twice to select the received
rPush [0•OPT] then push [Y
GPS message.
tPush [0• OPT] for 1 sec. to enter the message.
Z] or [Y
Y] to move the
• Received message is indicated, push [Z
cursor to left or right, respectively.
tPush [✱•ENT
56
] (or [D•CLR]) to exit OPTION SET MODE.
yAfter checking a received position and message, push
[✱•ENT ] (or [D•CLR]) to return to normal operating mode.
OTHER FUNCTIONS
12
■ SET MODE
D Entering SET MODE
D Repeater tone frequency
q Push [A•FUNC], then push [8•SET] to enter SET MODE.
Y] or [Z
Z] to select the desired item.
w Push [Y
e Rotate [VOL] to select the condition/value.
Selects tone encoder frequency for accessing a repeater, etc.
from one of 50 available frequencies.
• To exit SET MODE, push [✱•ENT
Enter
• 67.0–254.1 Hz (50 tones): 88.5 Hz (default)
] (or [D•CLR]).
Set
Exit
[VOL]
D Tone squelch frequency
Selects frequency for tone squelch or pocket beep operation
from one of 50 available frequencies.
• 67.0–254.1 Hz (50 tones): 88.5 Hz (default)
FUNC
11
12
ENT
SET
• Available subaudible tone frequencies
67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
210.7
218.1
225.7
229.1
233.6
241.8
250.3
254.1
57
12
OTHER FUNCTIONS
D DTCS code
D Offset frequency
Selects DTCS (both encoder/decoder code) for DTCS
squelch operation. Total of 104 codes are available.
• 023–754: 023 (default)
Sets the duplex offset frequency within 0 to 20 MHz range.
During duplex (repeater) operation, transmit frequency (or receive when reverse function is set to ON) shifts the set frequency. (default value may differ depending on transceiver
types and versions)
D DTCS polarity
Selects DTCS polarities for transmission and reception from
“nn (default),” “nR,” “Rn” and “RR.” (n: normal/R: reverse)
D Reverse function
Turns the reverse function ON and OFF (default).
D Tuning step
Selects tuning step from 5, 10, 12.5, 15, 20, 25, 30 and
Y]/[Z
Z] or [VOL] (When [VOL] is assigned as tuning
50 kHz for [Y
dial) operation. (default value may differ depending on transceiver types and versions)
58
Reverse function OFF
Reverse function ON
OTHER FUNCTIONS
12
D Scan pause timer
D LCD backlight
Selects the scan pause time from SCt.5, SCt.10, SCt.15 and
SCP. 2. When receiving signals, the scan pauses according
to the scan pause time.
• SCt. 5/10/15 : Scan pauses for 5/10/15 sec.
(default: SCt.15)
• SCP. 2
: Scan pauses until the signal disappears. Resumes 2 sec. after the signal disappears.
Selects LCD backlight lighting condition from auto, ON and
OFF.
• LIG.At : Lights when any key except [PTT] is pushed.
(default)
• LIG.ON : Lights continuously while the transceiver is powered ON.
• LIG.OF : Never lights.
D Function key timer
D Transmission permission
Selects [A•FUNC] effect timer from F0.At, F1.At, F2.At, F3.At
Turns transmission permission ON and OFF. This function
can be set for each memory and call channel, independently.
• tX .ON : Transmission is permitted. (default)
• tX .OF : Transmission is inhibited.
and F .m.
• F0.At
: “ F ” disappears immediately after secondary function is operated. (default)
• F1/2/3.At: “ F ” disappears after 1/2/3 sec. after secondary
function is operated.
• F .m
: “ F ” appears until [A•FUNC] is pushed again.
12
59
12
OTHER FUNCTIONS
D Memory bank setting
D Wide/Narrow setting
Sets the desired memory bank (A to J and OFF) to assign the
regular memory channels.
This item appears when SET MODE is accessed from memory
mode only.
Selects both the transmission and reception passband width
from wide (default) and narrow.
When narrow is selected, the transmission and reception
passband width become half of the wide setting (approx.).
This setting can be set for each memory, call and VFO independently.
D Memory bank link function
Sets the memory bank link function ON and OFF (default).
The link function provides continuous banks scan, that scans
all contents in the selected banks during bank scan.
This item appears when SET MODE is accessed from memory
mode only.
• Bank link setting
q Rotate [VOL] to select the memory bank link function ON.
Y] or [Z
Z] to select the desired bank to be linked.
w Push [Y
• BLA: Bank A, BLB: Bank B, BLC: Bank C, BLD: Bank D,
BLE: Bank E, BLF: Bank F, BLG: Bank G, BLH: Bank H,
BLI: Bank I, BLJ: Bank J
e Rotate [VOL] to select “ON” to linking the bank.
r Repeat steps w and e to set the link condition.
60
D Weather alert function IC-V82 [USA] version only
Turns weather alert function ON and OFF (default).
OTHER FUNCTIONS
■ INITIAL SET MODE
AT
POWER ON
The INITIAL SET MODE is accessed at power on and allows you
to set seldom-changed settings. In this way, you can “customize” transceiver operations to suit your preference and operating style.
12
D Key-touch beep
Turns key-touch beep emission ON (Beep level 1 to 3) and
OFF.
(default: 3)
D Entering INITIAL SET MODE
Y] and [Z
Z], turn power ON.
q While pushing [Y
Y] or [Z
Z] to select the desired item.
w Push [Y
e Rotate [VOL] to select the condition or value.
• To exit INITIAL SET MODE, push [✱•ENT
Enter
Set
] (or [D•CLR]).
Exit
[VOL]
D Time-out timer
To prevent accidental prolonged transmission, etc., the transceiver has a time-out timer. This function cuts a transmission
OFF after 1–30 min. of continuous transmission. This timer
can be cancelled.
• tOt.OF : The time-out timer is turned OFF. (default)
• tOt. 1–30: The transmission is cut OFF after the set period
elapses.
12
PWR
ENT
61
12
OTHER FUNCTIONS
D Auto repeater
U.S.A. version only
The auto repeater function automatically turns ON or OFF the
duplex operation and tone encoder. The offset and repeater
tone is not changed by the auto repeater function. Reset
these frequencies, if necessary.
• RPt.OF : The auto repeater function is turned OFF.
• RPt.R1 : Activates for duplex only. (default)
• RPt.R2 : Activates for duplex and tone.
D Repeater lock-out
Selects lockout type from repeater, busy and OFF.
• RLO.RP : The repeater lockout is turned ON.
• RLO.bu : The busy lockout is turned ON.
• RLO.OF : No lockout is activated. (default)
D Squelch delay
D Auto power-off
The transceiver can be set to automatically turn OFF after a
specified period with a beep when no key operations are performed.
• 30 min., 1 hour, 2 hours and OFF (default) can be specified.
The specified period is retained even when the transceiver
is turned OFF by the auto power-off function. To cancel the
function, select “POF.OF” in this SET MODE.
NOTE: While an optional UT-118 DIGITAL UNIT is installed
and GPS automatic transmit function is activated, this
function does not work.
62
Selects squelch delay from short and long to prevent repeated opening and closing of the squelch during reception
of the same signal.
• Sqt. S: The squelch closes in short delay. (default)
• Sqt. L: The squelch closes in long delay.
OTHER FUNCTIONS
12
D DTMF speed
D Display type
The rate at which DTMF memories send individual DTMF
characters can be set to accommodate operating needs.
• 1: 100 msec. interval; 5.0 cps speed (default)
• 2: 200 msec. interval; 2.5 cps speed
• 3: 300 msec. interval; 1.6 cps speed
• 5: 500 msec. interval; 1.0 cps speed (cps=characters/sec.)
Selects LCD indication type from frequency, channel number
and channel names.
• dSP.FR : Shows frequency (default)
• dSP.CH : Shows channel number*
• dSP.Nm : Shows channel names†
*Only memory channels can be selected.
†
Frequency indication will be displayed when the selected memory
channel has not programmed memory name.
D Dial assignment
Selects [VOL] control action from AF volume and tuning dial.
• tOP.VO: AF volume (default)
• tOP.dI : Tuning dial
D LCD contrast
Selects LCD contrast from auto, high and low.
• LCd.At : Automatic (default)
• LCd.HI : High contrast
• LCd.LO : Low contrast
12
63
12
OTHER FUNCTIONS
D Power save
D Tuning speed acceleration
Selects duty cycle for power save function from auto, 1:32,
1:16, 1:8, 1:2 and OFF.
• P–S.At : Duty cycle changes automatically. (default)
• P–S.32 : 1:32 duty cycle
• P–S.16 : 1:16 duty cycle
• P–S. 8 : 1:8 duty cycle
• P–S. 2 : 1:2 duty cycle
• P–S.OF : The power save function is turned OFF.
The tuning speed acceleration automatically speeds up the
Y] or [Z
Z], or rotattuning speed when pushing and holding [Y
ing [VOL] rapidly.*
• S–S.At : The tuning speed acceleration is activated. (default)
• S–S. m : The tuning speed acceleration is not activated.
*When tuning dial is assigned with [VOL].
NOTE: While DV mode operation (with UT-118), or pager/
CSQL operation (with UT-108), the active duty cycle is fixed
1:1 only (even any duty cycle setting other than OFF).
D Monitor key action
The monitor key, [MONI], can be set as a ‘sticky’ key. When
set to the sticky condition, each push of [MONI] toggles the
monitor function ON and OFF.
• PU (Push)
: Pushing and holding [MONI] to monitor
the frequency. (default)
• HO (Hold)
: Push [MONI] to monitor the frequency
and push again to cancel it.
64
OTHER FUNCTIONS
D Mic simple mode
Optional HM-75A required
This item turns the microphone simple mode ON and OFF.
Microphone simple mode is used to change the function assignments for keys in the optional HM-75A REMOTE CONTROL
SPEAKER-MICROPHONE as below. This assignment is convenient for 3-channel use of simple operation.
• mIC.n1 : Normal 1 (default)
• mIC.n2 : Normal 2
• mIC.Sm: Simple mode
HM-75A
Mode
key
12
NORMAL1
NORMAL2
SIMPLE
[A]
Freq.
CH
[B•CALL]
Null
[MONI]
[MONI]
[B]
Freq.
CH
VFO/Memory
Null
VFO/Memory
Null
[B•CALL]
Y]
[Y
Freq.
CH
Freq. Up
Memory CH Up
Freq. Up
Memory CH Up
MR-00CH
Z]
[Z
Freq.
Freq. Down
Freq. Down
CH Memory CH Down Memory CH Down
NOTE:
Turn power OFF when connecting the HM-75A to the
transceiver.
VFO mode cannot be selected via the microphone when
SIMPLE mode is selected.
D S-meter squelch
Sets S-meter squelch threshold level from OFF (default) and
S1–S3.
This setting allows you to set a minimum signal level needs to
open the squelch.
D ALC function
MR-01CH
12
Sets the ALC (automatic Level Control) function ON and OFF
(default).
The ALC function reduces the microphone gain automatically
when the transmission audio is distorted.
A 1750 Hz tone can be transmitted with the HM-75A operation.
➥ Push [A] while pushing [PTT].
65
12
OTHER FUNCTIONS
D Battery protection function
Sets the Battery protection function for LI (Li-Ion) and OFF
(default).
LI(Li-Ion):
➥ The transceiver is required pushing [PWR] for tuning
power ON with every battery detach and attach.
➥ Beep sounds when the attached battery is exhaustion.
■ Weather channel operation
(IC-V82 [USA] version only)
D Weather channel selection
q Push [C•MR] several times to select weather channel group.
• The battery must be charged presently.
OFF : The transceiver memorizes the transceiver ON/OFF
condition at battery is detached.
NOTE: This item MUST be set “LI” (Li-Ion) when the attaching battery is BP-211N (Li-Ion).
Weather channel group indication
Y] or [Z
Z] several times to select the desired
w Push [Y
weather channel.
e Push [C•MR] to select memory mode, or push [D•CLR] to
select VFO mode.
D Weather alert function
NOAA broadcast stations transmit weather alert tones before
important weather announcements. When the weather alert
function is turned ON, the selected weather channel is monitored each 5 sec. for the announcement. When the alert signal is detected, the “ALt” and the WX channel are displayed
alternately and sounds a beep tone until the transceiver is operated. The previously selected (used) weather channel is
checked periodically during standby or while scanning.
66
OTHER FUNCTIONS
■ CPU reset
q Select the desired weather channel.
w Turn the weather alert function ON in set mode.
➥ Push [A•FUNC] and [8•SET] to enter SET MODE.
Y] or [Z
Z] to select the weather alert item, then
➥ Push [Y
rotate [VOL] to set ON.
➥ push [✱•ENT ] (or [D•CLR]) to exit SET MODE.
e Sets the desired stand-by condition.
• Selects VFO, memory or call channel.
• Scan or priority watch operation can also be selected.
r When the alert is detected, a beep sounds and the following indication will be displayed.
AT
12
POWER ON
The function display may occasionally
display erroneous information (e.g. when
first applying power). This may be
caused externally by static electricity or
other factors.
If this problem occurs, turn power OFF.
After waiting a few seconds, turn power
ON again. If the problem persists, perform CPU resetting operation as follows.
MONI
PWR
CLR
• While pushing [MONI] and [D•CLR],
turn power ON.
CAUTION:
Resetting the CPU returns the radio to factory default settings.
Shows above indications alternately.
t Turn the weather alert function OFF in SET MODE.
■ Partial reset
☞ NOTE: While receiving a signal (on a frequency other than
the weather alert ON frequency), the receiving signal or
audio will be interrupted momentarily every 5 sec. (approx.)
in case the alert function is turned ON. This symptom is
caused by the WX alert function. To cancel these symptoms, set the weather alert item OFF in SET MODE.
If you want to initialize the operating
conditions (VFO frequency, VFO settings, set mode contents) without
clearing the memory contents, a partial resetting function is available for
the transceiver.
• While pushing [D•CLR], turn the
power ON to partially reset the
transceiver.
AT
POWER ON
12
PWR
CLR
67
13
CLONING
Cloning allows you to quickly and easily transfer the programmed contents from one transceiver to another transceiver.
D Transceiver-to-transceiver cloning
AT
POWER ON
q Connect the OPC-474 CLONING CABLE to the [SP] jack of
the master and sub-transceivers.
• The master transceiver is used to send data to the sub-transceiver.
e Push [PTT] on the master transceiver.
• “CL OU” appears in the master transceiver’s display and S-meter
indicator shows that data is being transferred to the sub-transceiver.
• “CL IN” appears automatically in the sub-transceiver’s display
and S-meter indicator shows that data is being received from the
master transceiver.
r When cloning is finished, turn power OFF, then ON again
to exit cloning mode.
D Cloning using a PC
Please refer to the HELP file that comes with CS-V82
CLONING SOFTWARE.
OPC-478 (RS-232C type)
to RS-232C port
OPC-478U (USB type)
Y],
w While pushing [A•FUNC] and [Y
turn power ON to enter cloning
mode (master transceiver only—
power ON only for sub-transceiver).
to USB port
TRANSCEIVER
• “CLONE” appears and the transceivers
enter the clone standby condition.
PWR
FUNC
68
PC
NOTE: DO NOT push the [PTT] on the sub-transceiver
during cloning. This will cause a cloning error.
OPTIONAL UNIT
14
■ Optional UT-108/118 installation
■ Optional MB-86 installation
q Remove the optional connecter access cover.
D MB-86 stopper
• Unscrew two screws and remove the optional connector cover.
Supplied screws
w Attach the optional unit. Insert
the connector tightly to avoid a
bad contact.
D MB-86 belt clip
When clipping to a part of your belt
e Replace the optional connector
cover and two screws.
When releasing
13
14
r Program the necessary information from the transceivers
key pads or using the cloning software, before operation.
69
14
OPTIONAL UNIT
D MB-86 stopper
• When attaching
• When removing
CAUTION!
HOLD THE TRANSCEIVER TIGHTLY, WHEN ATTACHING OR REMOVING THE TRANSCEIVER FROM THE
BELT CLIP.
If the transceiver is accidentally dropped and the swivel
belt clip’s stopper is cracked or damaged, the swivel belt
clip may not work properly.
Once the transceiver is locked in place,
it will swivel 360 degrees.
70
SPECIFICATIONS
15
■ IC-V82
GENERAL
• Frequency coverage
USA
Europe, Taiwan, Korea
General (LM), CSA (LM)
TRANSMITTER
: (unit: MHz)
Tx: 144–148/Rx: 136–174*
Tx/Rx: 144–146
Tx/Rx: 136–174*
*Guaranteed: 144–148 MHz range only.
• Type of emission
: FM
• Number of memory channels : 207 (incl. 6 scan edges and 1 call)
• Frequency resolution
: 5, 10, 12.5, 15, 20, 25, 30, 50 kHz
• Operating temperature range : –10°C to +60°C; +14˚F to +140˚F
• Frequency stability
: ±2.5 ppm (–10°C to +60°C)
• Power supply requirement
: 7.2 V DC (6–10.3 V DC acceptable;
Icom’s battery pack only)
• Current drain (at 7.2 V DC: approx.):
Transmit
at 7 W (High) 2.6 A
at 4 W (Middle) 2.0 A
at 0.5 W (Low) 1.0 A
Receive
standby
80 mA
power save
30 mA
max. audio
250 mA
• Antenna connector
: BNC (50 Ω)
• Dimensions (proj. not included) : 54(W) × 139(H) × 36.7(D) mm
21⁄8(W)×515⁄32(H)×17⁄16(D) in
• Weight (approx.)
: 390 g; 13.8 oz
• Modulation system
• Output power (at 7.2 V)
• Max. frequency deviation
• Spurious emissions
• Microphone connector
: Variable reactance frequency mod.
: 7 W/4 W/0.5 W (High/Mid/Low)
: ±5.0 kHz [Wide]/±2.5 kHz [Narrow]
: Less than –60 dBc
: 3-conductor 2.5 (d) mm (1⁄8″)/2.2 kΩ
RECEIVER
• Receive system
: Double-conversion superheterodyne
• Intermediate frequencies
: 1st: 46.35 MHz, 2nd: 450 kHz
• Sensitivity (at 12 dB SINAD)
: 0.16 µV typical
• Squelch sensitivity (threshold) : 0.11 µV typical
• Selectivity
[Wide]
More than 55 dB
[Narrow]
More than 50 dB
• Spurious and image rejection : 80 dB typical
• Intermodulation
: 65 dB typical
• AF output power (at 7.2 V DC) : More than 0.3 W at 10% distortion with
an 8 Ω load
• Ext. speaker connector
• Ext. data connector
: 3-conductor 3.5 (d) mm (1⁄8″)/8 Ω
: 3-conductor 2.5 (d) mm (1⁄8″)
14
15
(with BP-222N and Ant.)
200 g; 7.1 oz
(without battery pack and Ant.)
All stated specifications are subject to change without notice or obligation.
71
15
SPECIFICATIONS
■ IC-U82
GENERAL
• Frequency coverage
USA
Europe, Korea
General (LM), China
TRANSMITTER
: (unit: MHz)
Tx: 420–450*1/Rx: 400–479*1
Tx/Rx: 430–440
Tx/Rx: 400–479*2
*1Guaranteed: 440–450 MHz range only.
*2Guaranteed: 430–440 MHz range only.
• Type of emission
: FM
• Number of memory channels : 207 (incl. 6 scan edges and 1 call)
• Frequency resolution
: 5, 10, 12.5, 15, 20, 25, 30, 50 kHz
• Operating temperature range : –10°C to +60°C; +14˚F to +140˚F
• Frequency stability
: ±2.5 ppm (–10°C to +60°C)
• Power supply requirement
: 7.2 V DC (6–10.3 V DC acceptable;
Icom’s battery pack only)
• Current drain (at 7.2 V DC: approx.):
Transmit
at 5 W (High) 2.0 A
at 2 W (Middle) 1.4 A
at 0.5 W (Low) 0.9 A
Receive
standby
80 mA
power save
30 mA
max. audio
250 mA
• Antenna connector
: BNC (50 Ω)
• Dimensions (proj. not included) : 54(W) × 139(H) × 36.7(D) mm
21⁄8(W)×515⁄32(H)×17⁄16(D) in
• Weight (approx.)
: 390 g; 13.8 oz
• Modulation system
• Output power (at 7.2 V)
• Max. frequency deviation
• Spurious emissions
• Microphone connector
RECEIVER
• Receive system
: Double-conversion superheterodyne
• Intermediate frequencies
: 1st: 46.35 MHz, 2nd: 450 kHz
• Sensitivity (at 12 dB SINAD)
: 0.16 µV typical
• Squelch sensitivity (threshold) : 0.11 µV typical
• Selectivity
[Wide]
More than 55 dB
[Narrow]
More than 50 dB
• Spurious and image rejection : 70 dB typical
• Intermodulation
: 65 dB typical
• AF output power (at 7.2 V DC) : More than 0.3 W at 10% distortion with
an 8 Ω load
• Ext. speaker connector
• Ext. data connector
(with BP-222N and Ant.)
200 g; 7.1 oz
(without battery pack and Ant.)
All stated specifications are subject to change without notice or obligation.
72
: Variable reactance frequency mod.
: 5 W/2 W/0.5 W (High/Mid/Low)
: ±5.0 kHz [Wide]/±2.5 kHz [Narrow]
: Less than –60 dBc
: 3-conductor 2.5 (d) mm (1⁄8″)/2.2 kΩ
: 3-conductor 3.5 (d) mm (1⁄8″)/8 Ω
: 3-conductor 2.5 (d) mm (1⁄8″)
Options
D BATTERY PACKS
Battery
pack
Voltage
16
D BELT CLIP
Capacity
Battery life*1
BP-208N
Battery case for AA
(LR6)×6 alkaline
BP-209N
7.2 V
1100 mAh
BP-210N
7.2 V
1650 mAh
6 hrs.
BP-211N
7.4 V
1800 mAh
6 hrs. 10 min.
BP-222N
7.2 V
600 mAh
2 hrs. 15 min.
—*2
3 hrs. 20 min.
* Operating periods are calculated under the following conditions:
Tx:Rx:standby=1:1:8, power save function: auto setting, is activated
*2Operation with the LOW output power selection is recommended.
• MB-103/MB-86 BELT CLIPS
MB-103: Same as that supplied with the transceiver.
MB-86: Swivel belt clip
• MB-96F/MB-96N LEATHER BELT HANGER
MB-96F: Fixed type belt hanger for use with MB-103.
MB-96N: Swivel belt hanger. MB-86’s base clip is required.
D INTERNAL UNIT
• UT-108 DTMF DECODER UNIT
Provides pager and code squelch capabilities.
• UT-118 DIGITAL UNIT
Provides digital mode operation capabilities.
D CHARGER
• BC-144N DESKTOP CHARGER + BC-145 AC ADAPTER
For rapid charging of battery packs. An AC adapter is supplied with the charger. Charging time: 1.5 to 2 hrs.
• BC-146 BATTERY CHARGER + BC-147 AC ADAPTER
For regular charging of battery packs. An AC adapter is additionally required. Charging time: 6.5 to 18.5 hrs.
• BC-119N DESKTOP CHARGER + AD-101 CHARGER ADAPTER
For rapid charging of battery packs. An AC adapter is supplied with the charger. Charging time: 1.5 to 2 hrs.
• BC-121N MULTI-CHARGER + AD-101 CHARGER ADAPTER
(6 pcs.)
For rapid charging of up to 6 battery packs (six AD-101’s are
required) simultaneously. An AC adapter may be supplied
depending on version. Charging time: 1.5 to 2 hrs.
D OTHER OPTIONS
• HM-75A/HM-131L SPEAKER-MICROPHONES
Combination speaker-microphones that provide convenient
operation while hanging the transceiver from your belt.
HM-75A has 4 function switches for remote control capabilities.
HM-131L has moisture proof construction.
• HM-128L EARPHONE-MICROPHONE
You can clip the microphone with PTT switch to your lapel or
breast pocket.
• HS-85 HEADSET
Allows you hands-free operation. Includes VOX, PTT and
“one-touch” PTT with time-out timer.
15
16
73
16
Options
• VS-1L PTT/VOX UNIT+HS-94/HS-95/HS-97 HEADSET
VS-1L PTT/VOX UNIT
Required when using these headsets.
HS-94 EAR-PIECE TYPE HEADSET
Earhook headset with flexible boom microphone.
HS-95 NECK-ARM TYPE HEADSET
Behind-the-head headset with flexible boom microphone.
HS-97 THROAT MICROPHONE
Throat microphone fits around your neck and picks up a
speech vibration.
• CS-V82 CLONING SOFTWARE+OPC-478/U CLONING CABLE
Provide quick and easy programming of memory channel,
memory name etc.
• OPC-474 CLONING CABLE
For cloning between transceivers.
• SP-13 EARPHONE
Provides clear receive audio in noisy environments.
• FA-B2E WHIP ANTENNA
Same as that supplied with the transceiver.
Some options may not be available in some countries. Please ask your dealer for details.
74
MEMO
75
Printed in Japan
© 2004 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 88
Page Mode                       : UseThumbs
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:bb831991-fdac-4ba9-a19f-7313ae08419a
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Create Date                     : 2004:10:18 00:34:03Z
Modify Date                     : 2004:11:16 11:53:16-05:00
Metadata Date                   : 2004:11:16 11:53:16-05:00
Document ID                     : uuid:a66e4b2f-ee3c-4721-aa66-e809bf42b46b
Format                          : application/pdf

EXIF Metadata provided by EXIF.tools