ICOM orporated 296400 Scanning Receiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	745010
Application ID	zLaIXO/z4ynJfS3Sls0xbQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	308.97kB (3862182 bits)
Date Submitted	2007-01-08 00:00:00
Date Available	2007-01-08 00:00:00
Creation Date	2006-11-15 08:55:05
Producing Software	Acrobat Distiller 5.0.5 for Macintosh
Document Lastmod	2007-01-04 11:21:33
Document Title	Users Manual

INSTRUCTION MANUAL
FM TRANSCEIVER
iV85
iV85E
iV85-T
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FOREWORD
IMPORTANT
Thank you for purchasing this Icom transceiver. The IC-V85
FM TRANSCEIVER is designed and built with Icom’s superior
technology and craftsmanship. With proper care, this transceiver should provide you with years of trouble-free operation.
READ ALL INSTRUCTIONS carefully and completely
We want to take a couple of moments of your time to thank
you for making the IC-V85 your radio of choice, and hope you
agree with Icom’s philosophy of “technology first.” Many hours
of research and development went into the design of your ICV85.
D FEATURES
❍ 7 W*— high transmit output power
*7 W : IC-V85 except [THA] version,
5.5 W : IC-V85 [THA] version
❍ CTCSS and DTCS encoder/decoder standard
before using the transceiver.
SAVE THIS INSTRUCTION MANUAL— This instruction manual contains important operating instructions for
the IC-V85.
EXPLICIT DEFINITIONS
WORD
DEFINITION
Personal injury, fire hazard or electric shock
R WARNING!
may occur.
CAUTION
NOTE
Equipment damage may occur.
Recommended for optimum use. No risk of
personal injury, fire or electric shock.
❍ Optional DTMF decoder
Icom, Icom Inc. and the
logo are registered trademarks of Icom
Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
PRECAUTIONS
RWARNING RF EXPOSURE! This device emits
Radio Frequency (RF) energy. Extreme caution should be observed when operating this device. If you have any questions
regarding RF exposure and safety standards please refer to
the Federal Communications Commission Office of Engineering and Technology’s report on Evaluating Compliance
with FCC Guidelines for Human Radio frequency Electromagnetic Fields (OET Bulletin 65)
RWARNING! NEVER hold the transceiver so that the
antenna is very close to, or touching exposed parts of the
body, especially the face or eyes, while transmitting. The
transceiver will perform best if the microphone is 5 to 10 cm
(2 to 4 inches) away from the lips and the transceiver is vertical.
RWARNING! NEVER operate the transceiver with a
headset or other audio accessories at high volume levels.
Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the
volume or discontinue use.
RWARNING! NEVER operate the transceiver while
driving a vehicle. Safe driving requires your full attention—
anything less may result in an accident.
RWARNING! NEVER connect the transceiver to an AC
outlet. This may pose a fire hazard or result in an electric shock.
NEVER connect a power supply of more than 16 V DC
through the optional CP-19R CIGARETTE LIGHTER CABLE to the
[DC 11V] jack to prevent damaging the transceiver.
NEVER connect the transceiver to a power source using
reverse polarity. This will ruin the transceiver.
NEVER cut the DC power cable between the DC plug and
fuse holder. If an incorrect connection is made after cutting,
the transceiver may be damaged.
NEVER expose the transceiver to rain, snow or any liquids.
The transceiver may be damaged.
NEVER operate or touch the transceiver with wet hands.
This may result in an electric shock or ruin the transceiver.
NEVER attempt to charge alkaline or dry cell batteries. Be
aware that external DC power connections will charge batteries inside the battery case. This will damage not only the battery case but also the transceiver.
DO NOT push the PTT when not actually desiring to transmit.
ii
PRECAUTIONS—continued
SUPPLIED ACCESSORIES
DO NOT operate the transceiver near unshielded electrical
q Antenna* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
w Hand strap* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
e 2251 OPT sheet*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
r Battery pack*/Battery case* . . . . . . . . . . . . . . . . . . . . . . 1
t Belt clip* (with screws) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
y AC Adapter*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
blasting caps or in an explosive atmosphere.
BE CAREFUL! The transceiver will become hot when
operating it continuously for long periods.
AVOID using or placing the transceiver in direct sunlight or
*Not supplied with some versions.
in areas with temperatures below –10°C (+14˚F) or above
+60°C (+140˚F).
Place the unit in a secure place to avoid inadvertent use by
children.
AVOID the use of chemical agents such as benzine or alcohol when cleaning, as they can damage the transceiver’s
surfaces.
Even when the transceiver power is OFF, a slight current still
flows in the circuits. Remove the battery pack or case from
the transceiver when not using it for a long time. Otherwise,
the battery pack (Li-Ion: BP-227) or installed batteries will become exhausted.
For USA only:
Caution: Changes or modifications to this transceiver, not expressly approved by Icom Inc., could void your authority to
operate this transceiver under FCC regulations.
iii
OPTION LIST
• BP-226 BATTERY CASE
Battery case for 5×AA (LR6) size alkaline batteries.
• BP-227 LI-ION BATTERY PACK
7.2 V/1700 mAh Lithium-Ion battery pack.
• BC-119N DESKTOP CHARGER + AD-100 CHARGER ADAPTER
For rapid charging of battery packs. An AC adapter is supplied with the charger. Charging time: approx. 2–2.5 hrs.
• BC-121N MULTI-CHARGER + AD-100 CHARGER ADAPTER
(6 pcs.)
For rapid charging of up to 6 battery packs (six AD-100’s are
required) simultaneously. An AC adapter may be supplied
depending on version. Charging time: approx. 2–2.5 hrs.
• CP-19R CIGARETTE LIGHTER CABLE WITH NOISE FILTER
Used for operation and charging a battery pack connected
to transceiver via a DC power source. (11.7 V–15.9 V DC)
• MB-98 BELT CLIP
MB-98: Same as that supplied with the transceiver.
• UT-108 DTMF DECODER UNIT
Provides pager and code squelch capabilities.
• SP-13 EARPHONE
Provides clear receive audio in noisy environments.
• FA-B2E WHIP ANTENNA
Same as that supplied with transceiver.
• HM-75A/HM-131L/HM-158L SPEAKER-MICROPHONES
Combination speaker-microphones that provide convenient
operation while hanging the transceiver from your belt.
HM-75A has 4 function switches for remote control capabilities.
HM-131L/HM-158L are equipped with an earphone jack and
a revolving clip.
• HM-128L/HM-153L/HM-166 EARPHONE-MICROPHONE
You can clip the microphone with PTT switch to your lapel or
breast pocket.
• HS-85 HEADSET
Allows you hands-free operation. Includes VOX, PTT and
“one-touch” PTT with time-out timer.
• VS-1L PTT/VOX UNIT+HS-94 HEADSET
VS-1L PTT/VOX UNIT
Required when using the headset.
HS-94 EAR-PIECE TYPE HEADSET
Earhook headset with flexible boom microphone.
• CS-V85 CLONING SOFTWARE+OPC-478/U/UC CLONING CABLE
Provide quick and easy programming of memory channel,
memory name etc.
• OPC-474 CLONING CABLE
For cloning between transceivers.
• LC-167 CARRYING CASE
Helps protect the transceiver from scratches, etc..
iv
TABLE OF CONTENTS
FOREWORD ........................................................................ i
IMPORTANT......................................................................... i
EXPLICIT DEFINITIONS...................................................... i
PRECAUTIONS .............................................................. ii–iii
SUPPLIED ACCESSORIES ............................................... iii
OPTION LIST .................................................................... iv
TABLE OF CONTENTS .................................................. v–vi
QUICK REFERENCE GUIDE ......................................... I–VI
■ Preparation................................................................... I
■ Your first contact ........................................................ IV
■ Repeater operation ..................................................... V
■ Programming memory channels................................ VI
1 ACCESSORIES.......................................................... 1–2
■ Accessory attachment................................................. 1
2 PANEL DESCRIPTION .............................................. 3–8
■ Switches, controls, keys and connectors .................... 3
■ Function display .......................................................... 7
3 BATTERY PACKS .................................................... 9–16
■ Battery pack replacement ........................................... 9
■ Cautions .................................................................... 11
■ Regular charging ...................................................... 13
■ Rapid charging ......................................................... 14
■ External DC power operation .................................... 16
4 BASIC OPERATION............................................... 17–21
■ Power ON.................................................................. 17
■ VFO mode selection.................................................. 17
■ Setting a frequency ................................................... 17
■ Setting audio/squelch level ....................................... 19
■ Receive and transmit ................................................ 19
■ Monitor function......................................................... 19
■ Display type............................................................... 20
■ Key lock function ....................................................... 20
■ Weather channel operation
(USA version only) .................................................... 21
5 REPEATER OPERATION ...................................... 22–25
■ General ..................................................................... 22
■ Reversed duplex mode ............................................. 22
■ Offset frequency ........................................................ 23
■ Subaudible tones ...................................................... 23
■ Repeater lockout ....................................................... 24
■ Auto repeater function (USA version only) ................ 25
6 MEMORY/CALL OPERATION ............................... 26–31
■ General description ................................................... 26
■ Selecting a memory channel..................................... 26
■ Selecting the call channel ......................................... 26
■ Programming the memory/call channels................... 27
■ Channel name programming..................................... 28
■ Memory transfers ...................................................... 28
■ Memory bank selection ............................................. 30
■ Memory bank setting................................................. 30
■ Transferring bank contents........................................ 31
11 SET MODES........................................................... 47–56
■ SET MODE ............................................................... 47
■ INITIAL SET MODE .................................................. 51
7 DTMF MEMORY..................................................... 32–34
■ Programming a DTMF code sequence ..................... 32
■ Transmitting a DTMF code sequence ....................... 33
■ DTMF transmission rate............................................ 34
12 SET MODE INSPECTION ...................................... 57–58
8 SCAN OPERATION................................................ 35–38
■ Scan types ................................................................ 35
■ Programmed scan..................................................... 35
■ Memory scan..............................................................36
■ Skip channels............................................................ 37
■ Scan resume condition.............................................. 37
■ Priority watch............................................................. 38
9 SUBAUDIBLE TONES ........................................... 39–42
■ Tone squelch ............................................................. 39
■ Pocket beep operation .............................................. 41
■ Tone scan.................................................................. 42
10 PAGER/CODE SQUELCH
(Requires Optional UT-108).................................. 43–46
■ Pager function ........................................................... 43
■ Code programming ................................................... 43
■ Pager operation......................................................... 45
■ Code squelch ............................................................ 46
13 CLONING ............................................................... 59–60
■ Transceiver-to-transceiver cloning ............................ 59
■ Cloning using a PC ................................................... 60
14 RESETTING FUNCTIONS ........................................... 61
■ Partial reset ............................................................... 61
■ CPU reset.................................................................. 61
15 TROUBLESHOOTING ................................................. 62
16 OPTION ........................................................................ 63
■ Optional UT-108 installation ...................................... 63
17 SPECIFICATIONS ........................................................ 64
■ General ..................................................................... 64
■ Transmitter ................................................................ 64
■ Receiver .................................................................... 64
18 CE........................................................................... 65–66
10
11
12
13
14
15
16
17
18
19
vi
QUICK REFERENCE GUIDE
■ Preparation
D Antenna
D Battery pack replacement
Attach the antenna to the transceiver
as illustrated at right.
Before replacing the battery pack, push and hold [PWR] for 1
sec. to turn the power OFF.
• To attach the battery pack
Slide the battery pack on the back of the transceiver in the direction of the arrow (q), then lock it with the battery release
button.
• Slide the battery pack until the battery release button makes a ‘click’
sound.
• To release the battery pack
Push the battery release button in the direction of the arrow
(w) as shown below. The battery pack is then released.
D Belt clip
Conveniently attaches to your belt.
Attach the belt clip with the supplied screws using a phillips
screwdriver.
Battery pack
To attach the belt clip
Battery release button
D Battery case— optional for some versions
When using a BP-226 BATTERY CASE attached to the transceiver, install 5 AA (LR6) size alkaline batteries as illustrated
at right.
q Hook your finger under the latch, and open the cover in the
direction of the arrow (q). (Fig.1)
w Then, install 5 × AA (LR6) size alkaline batteries. (Fig.2)
• Install the alkaline batteries only.
• Be sure to observe the correct polarity.
• Do not pin the ribbon under the batteries.
e Close the cover with fitting in the direction of the arrow (w)
first, then firm the latch in place (e). (Fig.1)
• Be sure to the gasket and the ribbon are set correctly,
and do not protrude out of the battery case. (Fig.3)
Fig.1
BP-226
Quick reference guide
QUICK REFERENCE GUIDE
Latch
Fig.2
Ribbon
R CAUTION!
• When installing batteries, make sure they are all the
same brand, type and capacity. Also, do not mix new and
old batteries together.
• Keep battery contacts clean. It’s a good idea to clean battery terminals once a week.
Fig.3
Gasket
Ribbon
II
QUICK REFERENCE GUIDE
D Regular charging
When using a BP-227 BATTERY PACK attached to the transceiver, prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and
operation.
Transceiver
• BC-167A/D
D Charging note
• Be sure to turn the transceiver power OFF.
Otherwise the battery pack will not be charged completely or takes
longer charging time periods.
• External DC power operation becomes possible when using
an optional CP-19R. The attached battery pack is also
charged simultaneously, except during transmit. (see p. 16
for more details)
Even through there is no indication during regular charging, the transceiver automatically stops charging the battery pack when the battery pack is fully charged (BP-227’s
voltage becomes approx. 7.2 V) or the continuous charging time is over 15 hours.
III
to
[DC 11V]
to AC outlet
• CP-19R (Optional)
Turn power OFF
while charging the
battery pack.
• Charging time period:
Approx. 12–13 hours
to cigarette lighter
socket (12 V DC)
QUICK REFERENCE GUIDE
Now that you have your IC-V85 ready, you are excited to get
on the air. We would like to walk you through a few basic operational steps to make your first “On The Air” use an enjoyable experience.
Quick reference guide
■ Your first contact
2. Adjusting audio output level
➥ Rotate [VOL] to set the desired
audio level.
[VOL]
D About default setting
Y]/[Z
Z]
The [VOL] control function can be exchanged with [Y
keys function in INITIAL SET MODE. However, in this QUICK
REFERENCE, the factory default setting ([VOL] controls
audio output level) is used to simplify instructions.
D Basic operation
3. Adjusting the squelch level
➥ While pushing and holding
Y] or [Z
Z] to set
[MONI], push [Y
the squelch level.
PWR
MONI
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
1. Turning ON the transceiver
Although you have purchased a brand new transceiver, some
settings may be changed from the factory defaults because
of the Quality Control
process. Resetting the CPU
is necessary to start from
factory default.
➥ While pushing [MONI]
and [CLR], push and
hold [PWR] for 1 sec. to
reset the CPU and turn
power ON.
PWR
MONI
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
PRIO
SET
H/M/L
OPT
ENT
CLR
4. Tune the desired frequency
Y]/[Z
Z], will
The up/down keys, [Y
allow you to tune to the frequency
that you want to operate on. Page
18 will instruct you on how to adjust
the tuning step size.
PWR
Y] or [Z
Z] to adjust the fre➥ Push [Y
quency.
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
IV
QUICK REFERENCE GUIDE
Direct frequency input from the
keypad is also available.
■ Repeater operation
➥ To enter the desired frequency,
enter 6 digits starting from the
100 MHz digit.
1. Setting duplex
• Entering three* to five digits then
pushing [✱ ENT] will also set the frequency. (*Some versions only requires two digits.)
• When a digit is mistakenly input,
push [CLR] to abort input.
➥ Push [FUNC], then [DUP](4) several times to select minus duplex
or plus duplex.
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
CLR
• The USA version has an auto repeater function, therefore, setting duplex is not required.
ENT
Keypad
• Example 1— when entering 145.525 MHz
TONE
Push
DUP
PWR
ENT
SCAN
SCAN
P.BEEP
SCAN
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
FUNC
DUP
2. Repeater tone
➥ Push [FUNC], then [TONE](1) several times until “ ” appears, if required.
• Example 2— when entering 144.800 MHz
TONE
Push
DUP
DUP
SET
OPT
ENT
PWR
5. Transmit and receive
➥ Push and hold [PTT] to transmit, then speak into the microphone; release to receive.
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
FUNC
TONE
■ Programming memory channels
The IC-V85 has a total of 107 memory channels (including 6
scan edges and 1 call channel) for storing often used operating frequency, repeater settings, etc.
3. Writing a memory channel
➥ Push [FUNC], then push and hold
[MR] for 1 sec. to program.
• 3 beeps sound.
1. Setting frequency
In VFO mode, set the desired operating frequency with other
desired settings, such as repeater and subaudible tone.
MR
PWR
2. Selecting a memory channel
➥ Push [FUNC] and [MR] then push
Y] or [Z
Z] several times to select
[Y
the desired memory channel.
• “X” indicator and memory channel
number blink.
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
Quick reference guide
QUICK REFERENCE GUIDE
FUNC
ENT
• Continue to push and hold [MR] for 1 sec. after 3 beeps are emitted, to increment the displayed memory channel number.
MR
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
FUNC
ENT
VI
1
ACCESSORIES
■ Accessory attachment
D Antenna
Attach the antenna to the transceiver as illustrated below.
Keep the [SP/MIC] cap (SP/MIC jack cover) attached when
jacks are not in use to keep the contacts clean.
Attach the
[SP/MIC] cap.
[SP/MIC] cap
ACCESSORIES
D Belt clip
D Hand strap
Conveniently attaches to your belt.
Attach the belt clip with the supplied screws using a phillips
screwdriver.
Slide the hand strap through the loop on the top of the rear panel
as illustrated below. Facilitates carrying.
To attach the belt clip
10
11
12
13
14
15
16
17
18
19
2
PANEL DESCRIPTION
■ Switches, controls, keys and connectors
q CONTROL DIAL
!0 ANTENNA CONNECTOR
Speaker
w PTT SWITCH
Microphone
MICROPHONE JACKS
e SQUELCH/MONITOR SWITCH
i FUNCTION DISPLAY
r UP/DOWN KEYS
u POWER KEY
t KEYPAD
o EXTERNAL SPEAKER/
y EXTERNAL DC JACK
PANEL DESCRIPTION
q CONTROL DIAL [VOL] (p. 19)
Rotate to adjust the volume level.
Y]/[Z
Z] can be exThe assigned function for [VOL] and [Y
changed in INITIAL SET MODE (pgs. 18, 53).
w PTT SWITCH [PTT]
Push and hold to transmit; release to receive.
e SQUELCH/MONITOR SWITCH [MONI] (p. 19)
➥ Push and hold to open the squelch temporarily and
monitor the operating frequency.
Y] or [Z
Z] to
➥ While pushing and holding this key, push [Y
adjust the squelch level.
Y]/[Z
Z] can be
The assigned function for [VOL] and [Y
exchanged in INITIAL SET MODE (pgs. 18, 53).
Y]/[Z
Z] (p.18)
r UP/DOWN KEYS [Y
Selects the operating frequency, set mode items, etc.
Y]/[Z
Z] can be exThe assigned function for [VOL] and [Y
changed in INITIAL SET MODE (pgs. 18, 53).
t KEYPAD (pgs. 5, 6)
Used to enter operating frequency, the DTMF codes, etc.
y EXTERNAL DC JACK [DC 11V]
➥ Connect an external DC power supply through the optional CP-19R for external DC operation. (p. 16)
➥ Connect the supplied (or optional) wall charger, BC167A/D, to charge the attached battery pack. (p. 13)
u POWER KEY [PWR] (p. 17)
Push and hold for 1 sec. to turn the power ON and OFF.
i FUNCTION DISPLAY (pgs. 7, 8)
o EXTERNAL SPEAKER/MICROPHONE JACKS [SP/MIC]
Connect an optional speaker-microphone or headset, if desired. The internal microphone and speaker will not function when a connector is inserted.
See page iv for a list of available options.
!0 ANTENNA CONNECTOR (p. 1)
Connects the supplied antenna.
10
11
12
13
14
15
16
17
18
19
2
PANEL DESCRIPTION
D Keypad
CALL
MR
CLR
P.BEEP
T.SCAN
BANK
FUNC
TONE
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
FUNC
ENT
[FUNC]
Access to secondary function.
TONE
P.BEEP
T.SCAN
CALL
MR
CLR
[CALL]
Selects the call channel. (p. 26)
[MR]
➥ Selects a memory mode. (p. 26)
➥ After pushing [FUNC], enter into memory programming/editing mode. (pgs. 27–29)
➥ After pushing [FUNC], programs/transfers
VFO/memory or call channel contents into
memory channel/VFO when pushed and held
for 1 sec. (pgs. 27–29)
[CLR]
Selects VFO mode, aborts direct frequency input,
or cancels scanning, etc. (pgs. 17, 35)
[1•TONE]
➥ Input digit “1” during frequency input, memory
channel selection, etc. (pgs. 17, 26)
➥ After pushing [FUNC], selects the subaudible
tone function. (pgs. 22, 39)
[2•P.BEEP]
➥ Input digit “2” during frequency input, memory
channel selection, etc. (pgs. 17, 26)
➥ After pushing [FUNC], turns the pocket beep
function ON and OFF. (p. 41)
[3•T.SCAN]
➥ Input digit “3” during frequency input, memory
channel selection, etc. (pgs. 17, 26)
➥ After pushing [FUNC], starts tone scanning.
(pgs. 24, 42)
DUP
[4•DUP]
➥ Input digit “4” during frequency input, memory
channel selection, etc. (pgs. 17, 26)
➥ After pushing [FUNC], selects duplex function
(–duplex, +duplex, simplex). (p. 22)
SCAN
[5•SCAN]
➥ Input digit “5” during frequency input, memory
channel selection, etc. (pgs. 17, 26)
➥ After pushing [FUNC], starts scanning. (p. 35)
PANEL DESCRIPTION
SKIP
PRIO
SET
[6•SKIP]
➥ Input digit “6” during frequency input, memory
channel selection, etc. (pgs. 17, 26)
➥ After pushing [FUNC], sets and cancels skip
setting for memory scan during memory mode.
(p. 37)
[7•PRIO]
➥ Input digit “7” during frequency input, memory
channel selection, etc. (pgs. 17, 26)
➥ After pushing [FUNC], starts priority watch.
(p. 38)
[8•SET]
➥ Input digit “8” during frequency input, memory
channel selection, etc. (pgs. 17, 26)
➥ After pushing [FUNC], enters into SET MODE.
(p. 47)
H/M/L
[9•H/M/L]
➥ Input digit “9” during frequency input, memory
channel selection, etc. (pgs. 17, 26)
➥ After pushing [FUNC], switches transmit power
between high, middle and low output power.
(p. 19)
When the transceiver becomes hot during
high or middle output power operation, the
built-in protection circuit activates to reduce
the transmit output power to 3 W (approx.).
OPT
BANK
ENT
[0•OPT]
➥ Input digit “0” during frequency input, memory
channel selection, etc. (pgs. 17, 26)
➥ After pushing [FUNC], selects an optional function mode, such as pager or code squelch operation. (pgs. 45, 46)
[#•BANK]
After pushing [FUNC], enters a memory bank selection. (p. 30)
[✱ ENT• ]
➥ Sets the frequency even if the full 6 digits of
frequency have not been entered. (p. 17)
➥ After pushing [FUNC], switches key lock function ON and OFF when pushed and held for 1
sec. Lock all keys, except [PWR], [PTT],
[MONI] and audio level adjustment. (p. 20)
10
11
12
13
14
15
16
17
18
19
2
PANEL DESCRIPTION
■ Function display
q w
q e
q r
q o
!0
!2
!1
w SIGNAL INDICATOR
➥ Shows receiving signal strength as below.
Weak ⇐ RX Signal level ⇒ Strong
➥ Shows the output power level while transmitting.
!4
!3
q BUSY INDICATOR
➥ Appears when a signal is being received or the squelch
is open.
➥ Blinks while the monitor function is activated. (p. 19)
Low
Middle
High
e TRANSMIT INDICATOR (p. 19)
Appears during transmit.
r PAGER CALL INDICATOR (p. 46)
Blinks when a pager call is received. (This indicator appears only when an optional UT-108 DTMF DECODER UNIT
is installed.)
t DUPLEX INDICATOR (p. 23)
“+” appears when plus duplex, “–” appears when minus
duplex is selected.
PANEL DESCRIPTION
y TONE INDICATOR
➥ “ ” appears while the subaudible tone encoder is in
use. (p. 23)
➥ “ ” appears while the tone (CTCSS) squelch function
is in use. (p. 39)
➥ “ ” appears while the tone (DTCS) squelch function is
in use. (p. 39)
➥ “ ” appears with the “ ” or “ ” indicator while the
pocket beep function (CTCSS or DTCS) is in use.
(p. 41)
u OUTPUT POWER INDICATOR (p. 19)
➥ “L” appears when the low output power is selected.
➥ “M” appears when the middle output power is selected.
➥ “H” appears when high output power is selected.
i KEY LOCK INDICATOR (p. 20)
Appears when the key lock function is ON.
o FUNCTION INDICATOR
Appears while a secondary function is being accessed.
!0 AUTO POWER OFF INDICATOR (p. 52)
Appears while the auto power OFF function is activated.
!1 FREQUENCY READOUT
Shows operating frequency, channel number or channel
names, depending on display type (p. 20).
!2 MEMORY CHANNEL INDICATOR (p. 26)
➥ Shows the selected memory channel number.
➥ “C” appears when the call channel is selected.
!3 MEMORY MODE INDICATOR (p. 26)
Appears while in memory mode or channel number indication mode.
!4 SKIP CHANNEL INDICATOR (p. 37)
Appears when the selected memory channel is specified
as a skip channel.
10
11
12
13
14
15
16
17
18
19
3
BATTERY PACKS
■ Battery pack replacement
D Battery packs
q Before replacing the battery
pack, push and hold [PWR]
for 1 sec. to turn the power
OFF.
PWR
PWR
FUNC
CALL
MR
CLR
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
SET
H/M/L
ENT
w Push the battery release button in the direction of the
arrow as shown below. The battery pack is then released.
Battery pack
Battery release button
Voltage
BP-226
Battery case for AA
(LR6)×5 alkaline
BP-227
7.2 V
Capacity
1700 mAh
Battery life*1
—*2
7 hrs.
TONE
PRIO
Battery
pack
*1 Operating periods are calculated under the following conditions;
Tx : Rx : standby =1 : 1 : 8, power save function: auto setting is
activated
*2 Operating period depends on the alkaline cells used.
BATTERY PACKS
D Battery case— optional for some versions
When using a BP-226 BATTERY CASE attached to the transceiver, install 5 AA (LR6) size alkaline batteries as illustrated
at right.
q Hook your finger under the latch, and open the cover in the
direction of the arrow (q). (Fig.1)
w Then, install 5 × AA (LR6) size alkaline batteries. (Fig.2)
• Install the alkaline batteries only.
• Be sure to observe the correct polarity.
• Do not pin the ribbon under the batteries.
e Close the cover with fitting in the direction of the arrow (w)
first, then firm the latch in place (e). (Fig.1)
• Be sure to the gasket and the ribbon are set correctly,
and do not protrude out of the battery case. (Fig.3)
Fig.1
BP-226
Latch
Fig.2
Ribbon
R CAUTION!
• When installing batteries, make sure they are all the
same brand, type and capacity. Also, do not mix new and
old batteries together.
• Keep battery contacts clean. It’s a good idea to clean battery terminals once a week.
Fig.3
Gasket
Ribbon
10
11
12
13
14
15
16
17
18
19
10
3
BATTERY PACKS
■ Cautions
Misuse of Lithium-Ion batteries may result in the following hazards: smoke, fire, or the battery may rupture.
Misuse can also cause damage to the battery or degradation of battery performance.
• R DANGER! Use and charge only specified Icom battery
packs with Icom radios. Only Icom battery packs are tested
and approved for use with Icom radios. Using third-party or
counterfeit battery packs may cause smoke, fire, or cause
the battery to burst.
D Battery caution
• R DANGER! DO NOT hammer or otherwise impact the battery. Do not use the battery if it has been severely impacted
or dropped, or if the battery has been subjected to heavy
pressure. Battery damage may not be visible on the outside
of the case. Even if the surface of the battery does not show
cracks or any other damage, the cells inside the battery may
rupture or catch fire.
• R DANGER! NEVER use or leave battery pack in areas
with temperatures above +60˚C (+140˚F). High temperature
build up in the battery, such as could occur near fires or
stoves, inside a sun heated car, or in direct sunlight may
cause the battery to rupture or catch fire. Excessive temperatures may also degrade battery performance or shorten
battery life.
11
• R DANGER! DO NOT expose the battery to rain, snow,
seawater, or any other liquids. Do not charge or use a wet
battery. If the battery gets wet, be sure to wipe it dry before
using.
• R DANGER! NEVER incinerate an used battery pack since
internal battery gas may cause it to rupture, or may cause
an explosion.
• R DANGER! NEVER solder the battery terminals, or
NEVER modify the battery pack. This may cause heat generation, and the battery may burst, emit smoke or catch fire.
• R DANGER! Use the battery only with the transceiver for
which it is specified. Never use a battery with any other
equipment, or for any purpose that is not specified in this instruction manual.
• R DANGER! If fluid from inside the battery gets in your
eyes, blindness can result. Rinse your eyes with clean
water, without rubbing them, and see a doctor immediately.
• WARNING! Immediately stop using the battery if it emits an
abnormal odor, heats up, or is discolored or deformed. If any
of these conditions occur, contact your Icom dealer or distributor.
• WARNING! Immediately wash, using clean water, any part
of the body that comes into contact with fluid from inside the
battery.
BATTERY PACKS
• WARNING! NEVER put the battery in a microwave oven,
high-pressure container, or in an induction heating cooker.
This could cause a fire, overheating, or cause the battery to
rupture.
• CAUTION! Always use the battery within the specified temperature range for the transceiver (–10˚C to +60˚C; +14˚F
to +140˚F) and the battery itself (–10˚C to +60˚C; +14˚F to
+140˚F). Using the battery out of its specified temperature
range will reduce the battery’s performance and battery life.
• CAUTION! Shorter battery life could occur if the battery is
left fully charged, completely discharged, or in an excessive
temperature environment (above +45˚C; +113˚F) for an extended period of time. If the battery must be left unused for a
long time, it must be detached from the radio after discharging. You may use the battery until the battery becomes
about half-capacity, then keep it safely in a cool dry place
with the temperature between –20˚C to +35˚C (–4˚F to
+95˚F).
D Charging caution
• R DANGER! NEVER charge the battery pack in areas with
extremely high temperatures, such as near fires or stoves,
inside a sun heated car, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the battery to stop charging.
• WARNING! DO NOT charge or leave the battery in the battery charger beyond the specified time for charging. If the
battery is not completely charged by the specified time, stop
charging and remove the battery from the battery charger.
Continuing to charge the battery beyond the specified time
limit may cause a fire, overheating, or the battery may rupture.
• WARNING! NEVER insert the transceiver (battery attached
to the transceiver) into the charger if it is wet or soiled. This
could corrode the battery charger terminals or damage the
charger. The charger is not waterproof.
• CAUTION! DO NOT charge the battery outside of the specified temperature range: 10˚C to +40˚C (+50˚F to +104˚F).
Icom recommends charging the battery at +20˚C (+68˚F).
The battery may heat up or rupture if charged out of the
specified temperature range. Additionally, battery performance or battery life may be reduced.
10
11
12
13
14
15
16
17
18
19
12
3
BATTERY PACKS
■ Regular charging
When using a BP-227 BATTERY PACK attached to the transceiver, prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and
operation.
Transceiver
• BC-167A/D
D Charging note
• Be sure to turn the transceiver power OFF.
Otherwise the battery pack will not be charged completely or takes
longer charging time periods.
• External DC power operation becomes possible when using
an optional CP-19R. The attached battery pack is also
charged simultaneously, except during transmit. (see p. 16
for more details)
Even through there is no indication during regular charging, the transceiver automatically stops charging the battery pack when the battery pack is fully charged (BP-227’s
voltage becomes approx. 7.2 V) or the continuous charging time is over 15 hours.
13
to
[DC 11V]
to AC outlet
• CP-19R (Optional)
Turn power OFF
while charging the
battery pack.
• Charging time period:
Approx. 12–13 hours
to cigarette lighter
socket (12 V DC)
BATTERY PACKS
■ Rapid charging
D AD-100 installation
Install the AD-100 desktop charger adapter into the holder
space of the BC-119N/121N.
Screws supplied with
the charger adapter
Desktop charger adapter
AD-100
Connect the plugs of the BC-119N/121N to the AD-100 desktop charger adapter with the connector, then install the
adapter into the charger with the supplied screws.
Connectors
Plugs
BC-119N
10
11
12
13
14
15
16
17
18
19
14
3
BATTERY PACKS
D Rapid charging with the BC-119N+AD-100
D Rapid charging with the BC-121N+AD-100
The optional BC-119N provides rapid charging of battery
packs. The following items are additionally required.
The optional BC-121N allows up to 6 battery packs to be
charged simultaneously. The following items are additionally
required.
• AD-100 (Charger Adapter).
• An AC adapter (may be supplied with the BC-119N depending on
version) or the DC power cable (OPC-515L/CP-17L).
Transceiver
• Six AD-100 (Charger Adapter).
• An AC adapter (BC-157; may be supplied with the BC-121N depending on version) or the DC power cable (OPC-656).
Battery pack
Transceiver
Battery pack
Turn power OFF.
Turn power OFF.
AC adapter
(Not supplied with
some versions.)
AC adapter
(purchased
separately)
AD-100 charger
adapters are installed
in each slot.
AD-100 charger
adapter is installed in BC-119N.
ER
HARG
TI-C
MUL
OPC-515L or
CP-17L
Optional OPC-515L (for 13.8 V
power source) or CP-17L (for
12 V cigarette lighter socket)
can be used instead of the AC
adapter.
15
Charge indicator
(each indicator functions independently)
DC power cable (OPC-656)
(Connect with the DC power supply; 13.8 V/at least 7 A)
BATTERY PACKS
■ External DC power operation
An optional cigarette lighter cable (CP-19R; for 12 V cigarette
lighter socket) can be used for external power operation.
D Operating note
• BE SURE to use optional CP-19R when connecting a regulated 12 V DC power supply into the [DC 11V] jack of the
transceiver.
• The voltage of the external power supply must be within
11.7–15.9 V DC when using CP-19R.
• NEVER CONNECT OVER 16 V DC through CP19R.
Use an external DC-DC converter to connect the transceiver
through CP-19R to a 24 V DC power source.
• Disconnect the power cables from the transceiver when not
using it. Otherwise, the vehicle battery will become exhausted.
• The power save function is deactivated automatically during
external DC power operation.
Transceiver
to
[DC 11V]
to cigarette lighter
socket (12 V DC)
CP-19R (Optional)
10
11
12
13
14
15
16
17
18
19
16
4
BASIC OPERATION
■ Power ON
■ Setting a frequency
➥ Push and hold [PWR] for 1
sec. to turn power ON.
D Via the keypad
q Push [CLR] to select VFO mode, if necessary.
w To enter the desired frequency, enter 6 digits starting from
the 100 MHz digit.
PWR
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
• Entering three* to five digits then pushing [✱ ENT] will also set
the frequency. (*Some versions only requires two digits.)
• When changing 100 kHz and below, push [#] then enter the desired digits.
• When a digit is mistakenly input, push [CLR] to abort input.
• Example 1— when entering 145.525 MHz
ENT
TONE
Push
DUP
SCAN
SCAN
P.BEEP
SCAN
■ VFO mode selection
The transceiver has 2 basic operating modes: VFO mode and
memory mode.
• Example 2— when entering 144.800 MHz
TONE
Push
DUP
DUP
SET
OPT
ENT
➥ Push [CLR] to select VFO
mode.
PWR
17
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
CLR
• Example 3— when entering 145.000 MHz
from 145.525 MHz
BANK
Push
ENT
BASIC OPERATION
D By other methods
✔ For your information— [VOL] function assignment
Y]/[Z
Z] keys
Via the [Y
Y] or [Z
Z] several times to set the desired frequency.
➥ Push [Y
• Each push increases/decreases the frequency by the selected
tuning step. See next set of instructions for setting tuning step
size.
D Tuning step selection
[VOL]
The IC-V85 has 8 tuning steps—
5, 10, 12.5, 15, 20, 25, 30 and
50 kHz. The tuning step is selectable in SET MODE.
qPush [FUNC] then [SET](8) to
enter SET MODE.
Y] or [Z
Z] several times
wPush [Y
to select the tuning step item.
The [VOL] control can be
used as a tuning dial for frequency tuning instead of
Y]/[Z
Z] keys. However, when
[Y
[VOL] functions as tuning
Y]/[Z
Z] keys function as
dial, [Y
volume control.
[VOL]
qWhile pushing and holding
Y] and [Z
Z], turn power
[Y
ON to enter INITIAL SET
MODE.
Y] or [Z
Z] several
w Push [Y
times to select the dial assignment item, “tOP.”
e Rotate [VOL] to select the condition.
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
FUNC
SKIP
OPT
PRIO
SET
H/M/L
ENT
PWR
PWR
FUNC
CALL
MR
CLR
T.SCAN
BANK
TONE
P.BEEP
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
ENT
ENT
SET
eRotate [VOL] to select the desired tuning step.
r Push [✱ ENT] (or [CLR]) to exit SET MODE.
[VOL] is assigned as
AF volume control.
[VOL] is assigned as
tuning dial.
r To exit INITIAL SET MODE, push [✱ ENT] (or [CLR]).
10
11
12
13
14
15
16
17
18
19
18
4
BASIC OPERATION
■ Setting audio/squelch level
■ Receive and transmit
D To set the audio level
q Push and hold [PWR] for 1 sec. to turn the power ON.
w Adjust audio volume to the desired level.
e Set the frequency.
When a signal is received:
• Squelch opens and audio is emitted from the speaker.
• Signal indicator shows the relative signal strength level.
rPush [FUNC], then [H/M/L](9) to select output power between high, middle and low.
• “H” appears when high power is selected.
• “M” appears when middle power is selected.
• “L” appears when low power is selected.
t Push and hold [PTT] to transmit, then speak into the microphone.
• “$” appears.
• Do not hold the microphone too close to your mouth or
speak too loudly. This may distort the signal.
y Release [PTT] to receive.
Rotate [VOL] to set the desired
audio level while receiving a
signal.
[VOL]
• When no signal is received, push
and hold [MONI] while setting the
audio level.
• When [VOL] is assigned as tunY]/[Z
Z] to adjust
ing dial, push [Y
the audio output level. (pgs. 18,
53)
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
D To set the squelch level
While pushing [MONI], push
Y]/[Z
Z] to set the squelch
[Y
level.
• The squelch level “10” is tight
squelch, “1” is loose squelch and
“0” is open squelch.
• When [VOL] is assigned as tuning dial, rotate [VOL] while pressing [MONI]. (pgs. 18, 53)
■ Monitor function
MONI
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
This function is used to listen to weak signals without disturbing the squelch setting or to open the squelch manually even
when mute functions such as the tone squelch are in use.
➥ Push and hold [MONI] to monitor the operating frequency.
ENT
The [MONI] key can be set to ‘sticky’ operation in
SET MODE. See page 55 for details.
19
INITIAL
4
BASIC OPERATION
■ Display type
USING
INITIAL SET MODE
The transceiver has 3 display types to suit your operating
style during memory mode operation. The display type is
selected in INITIAL SET MODE (p. 53).
“Channel Name Indication” type
“Frequency Indication” type
Displays memory channel name you have assigned. In this
display pre-programmed memory channel names are displayed.
VFO mode is selectable.
Displays operating frequency.
“Channel Number Indication” type
• Programmed frequencies are indicated when you have not preprogrammed the channel names in the selected memory channel.
• Push and hold [MONI] to display the operating frequency.
■ Key lock function
Displays memory channel number. In this type only preprogrammed memory channel numbers are displayed.
VFO mode cannot be selected.
• When the channel indication type is selected, only the following
functions can be performed.
- Scan function (p. 35)
- Output power setting (p. 19)
- DTMF memory function (p. 32)
- Key lock function (see next set of instructions)
- Scan pause timer setting, function key timer setting and LCD
backlight setting in SET MODE (p. 49)
The key lock function prevents accidental frequency changes
and function activation.
Push [FUNC] then push and hold
](✱ ENT) for 1 sec. to toggle the
function ON and OFF.
PWR
• “ ” appears while the lock function is activated.
• [PWR], [PTT], [VOL] and [MONI] can be
operated regardless of this setting.
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
FUNC
SKIP
OPT
PRIO
SET
H/M/L
ENT
ENT
10
11
12
13
14
15
16
17
18
19
20
4
BASIC OPERATION
■ Weather channel operation (USA version only)
D Weather channel selection
q Push [MR] several times to select weather channel group.
Weather channel group indication
Y] or [Z
Z] several times to select the desired
w Push [Y
weather channel.
e Push [MR] to select memory mode, or push [CLR] to select VFO mode.
D Weather alert function
USING
• Select VFO, memory or call channel.
• Scan or priority watch operation can also be selected.
r When the alert is detected, a beep sounds and the following indication will be displayed.
SET MODE
An NOAA broadcast station transmits weather alert tone before important weather announcements. When the weather
alert function is turned ON, the selected weather channel is
monitored each 5 sec. for the announcement. When the alert
signal is detected, the “ALt” and the WX channel are displayed alternately and sounds a beep tone until the transceiver controls are manipulated. The previously selected
weather channel is checked periodically during standby or
while scanning.
21
q Select the desired weather channel.
w Turn the weather alert function ON in SET MODE.
➥ Push [FUNC] and [SET](8) to enter SET MODE.
Y] or [Z
Z] to select the weather alert item, then
➥ Push [Y
rotate [VOL] to set ON.
➥ push [✱ ENT] (or [CLR]) to exit SET MODE.
e Select the desired stand-by condition.
Shows above indications alternately.
• Weather alert function OFF
➥ Turn the weather alert function OFF in SET MODE.
• Repeat above procedure described at step w
NOTE: While receiving a signal (on a frequency other than
the weather alert ON frequency), the receiving signal or
audio will be interrupted momentarily every 5 sec. (approx.)
in case the alert function is turned ON. This is caused by
the WX alert function. To eliminate the interruptions, set the
weather alert item OFF in SET MODE.
REPEATER OPERATION
■ General
When using a repeater, the transmit frequency is shifted from
the receive frequency by the offset frequency. It is convenient
to program repeater information into memory channels.
q Set the receive frequency (repeater output frequency).
w Push [FUNC] and [DUP](4) several times to select “–” or “+.”
• “–” indicates the transmit frequency is shifted down; “+” indicates
the transmit frequency is shifted up.
• Blinking “–” or “+” indicates the reversed duplex mode is selected
in SET MODE (p. 48).
ePush [FUNC] and [TONE](1) several times to activate the
subaudible tone encoder, if required.
• “ ” appears.
• Select the desired subaudible tone frequency, if necessary.
(p. 23)
r Push and hold [PTT] to transmit.
• The displayed frequency automatically changes to the transmit
frequency (repeater input frequency).
• If “OFF” appears, check the offset frequency (see next page for
details) and direction.
t Release [PTT] to receive.
yPush and hold [MONI] to check whether the other station’s
transmit signal can be directly received.
■ Reversed duplex mode
USING
SET MODE
When the reversed duplex mode is selected, the receive frequency shifts. (Transmit frequency shifts in normal duplex mode.)
Each receive and transmit frequency is shown in the table
below with the following conditions;
Input frequency
Direction
Offset frequency
: 145.30 MHz
: – (negative)
: 0.6 MHz
q Push [FUNC], then push [SET](8) to enter SET MODE.
Y] or [Z
Z] several times until “REV” appears.
w Push [Y
Reversed
OFF
ON
Rx freq. 145.30 MHz 144.70 MHz
Tx freq. 144.70 MHz 145.30 MHz
e Rotate [VOL] to turn the reversed duplex mode ON or
OFF.
r Push [✱ ENT] (or [CLR]) to exit SET MODE.
10
11
12
13
14
15
16
17
18
19
22
5
REPEATER OPERATION
■ Offset frequency
USING
SET MODE
USING
SET MODE
When communicating through a repeater, the transmit frequency is shifted from the receive frequency by an amount
determined by the offset frequency.
Some repeaters require subaudible tones to be accessed.
Subaudible tones are added to your normal signal and must
be set in advance.
q Push [FUNC], then push [SET](8) to enter SET MODE.
Y] or [Z
Z] several times until “±” and offset frequency
wPush [Y
appear.
qPush [FUNC], then push [SET](8) to enter SET MODE.
Y] or [Z
Z] several times until “rt” appears.
wPush [Y
eRotate [VOL] to select the desired offset frequency.
• Selectable steps are the same as the pre-set tuning steps.
• The unit of the displayed offset frequency is “MHz.”
rPush [✱ ENT] (or [CLR]) to set the offset frequency and exit
SET MODE.
23
■ Subaudible tones
e Rotate [VOL] to select the desired subaudible tone.
rPush [✱ ENT] (or [CLR]) to set the selected tone and exit
SET MODE.
• Available subaudible tone frequencies
67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
(unit: Hz)
210.7 254.1
218.1
225.7
229.1
233.6
241.8
250.3
REPEATER OPERATION
D Tone information
Some repeaters require different tone system to be accessed.
■ Repeater lockout
USING
DTMF TONES
While pushing [PTT], push the desired DTMF keys ([0]–[9],
[A], [B], [C], [D], [#] and [✱]) to transmit DTMF tones.
• [✱] transmits tone “E,” [#] transmits tone “F.”
• The transceiver has 16 DTMF memory channels (p. 32).
1750 Hz TONE
Y] or [Z
Z] to transmit a 1750 Hz
While pushing [PTT], push [Y
tone signal.
✔ Convenient
Tone scan function: When you don’t know the subaudible
tone used for a repeater, the tone scan is convenient for detecting the tone frequency.
INITIAL SET MODE
This function helps prevent interference to other stations by
inhibiting your transmission when a signal is received. The
transceiver has two inhibiting conditions, repeater and busy.
Y] and [Z
Z], turn the power ON
q While pushing and holding [Y
to enter INITIAL SET MODE.
Y] or [Z
Z] several times until “RLO” appears.
w Push [Y
e Rotate [VOL] to select the repeater lockout function to
“RP,” “bU” or OFF.
• “RP”: Transmit is inhibited when a signal with un-matched subaudible tone is received.
• “bU”: Transmit is inhibited when a signal is received.
Push [FUNC], then push [T.SCAN](3) to start the tone scan.
• Push [CLR] to cancel the scan.
• When the required tone frequency is detected, the scan pauses.
r Push [✱ ENT] (or [CLR]) to exit INITIAL SET MODE.
10
11
12
13
14
15
16
17
18
19
24
5
REPEATER OPERATION
■ Auto repeater function (USA version only)
The USA version automatically activates the repeater settings
(duplex ON/OFF, duplex direction, tone encoder ON/OFF)
when the operating frequency falls within or outside of the
general repeater output frequency range. The offset and repeater tone frequencies are not changed by the auto repeater
function. Reset these frequencies, if necessary.
Y] and [Z
Z], turn the power ON
q While pushing and holding [Y
to enter INITIAL SET MODE.
Y] or [Z
Z] several times until “RPt” appears.
w Push [Y
e Rotate [VOL] to select the desired condition.
• “OF”— the auto repeater function is turned OFF;
• “R1”— the auto repeater function activates duplex only;
• “R2”— the auto repeater function activates duplex and tone.
r Push [✱ ENT] (or [CLR]) to exit INITIAL SET MODE.
25
USING
INITIAL SET MODE
• Frequency range and offset direction
Frequency range
Duplex direction
145.200–145.495 MHz
146.610–146.995 MHz
“–” appears
147.000–147.395 MHz
“+” appears
MEMORY/CALL OPERATION
■ General description
The transceiver has 107 memory channels including 6 scan
edge memory channels (3 pairs), and 1 call channel. Each
of these channels can be individually programmed with operating frequency (pgs. 17, 18), duplex direction (p. 22) and
offset (p. 23), subaudible tone encoder or tone squelch and
its tone frequency (pgs. 23, 40) and skip information* (p. 37).
In addition, a total of 10 memory banks, A to J, are available
for usage by group, etc.
*except for scan edge memory channels.
■ Selecting a memory channel
■ Selecting the call channel
q Push [MR] to select memory mode.
➥ Push [CALL] to select the call channel.
• “X” appears.
• “C” is displayed instead of the memory channel number.
• Push [CLR] or [MR] to select VFO or memory mode, respectively.
Push
MR
wEnter 2 digits to select the desired memory channel (or
Y]/[Z
Z] keys).
push the [Y
• The memory channels 0–9 are proceeded by a “0.”
• When [VOL] is assigned as tuning dial, rotate [VOL] to select
the memory channel. (pgs. 18, 53)
Push
TONE
DUP
(Selection example: Memory channel 14)
Push
CALL
“C” appears
10
11
12
13
14
15
16
17
18
19
26
6
MEMORY/CALL OPERATION
■ Programming the memory/call channels
qPush [CLR] to select VFO mode, if necessary.
w Set the desired frequency.
eSet other information, such as tone, duplex, as desired.
rPush [FUNC], then [MR] momentarily.
yPush [FUNC], then push and hold [MR] for 1 sec., when 3
beeps will sound to program the information into the selected memory channel and return to VFO.
• “X” and memory channel number blink.
MR
PWR
MR
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
• When programming the call channel, select “C.”
• When [VOL] is assigned as tuning dial, rotate [VOL] to select
the memory channel. (pgs. 18, 53)
PWR
27
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
FUNC
ENT
FUNC
Y] or [Z
Z] to select the desired memory channel.
tPush [Y
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
FUNC
ENT
• After 3 beeps are emitted, continue to hold [MR] to increment the
displayed memory channel number.
6
MEMORY/CALL OPERATION
■ Channel name programming
■ Memory transfers
qSelect a “Channel Name Indication” type in
MODE (p. 53).
wPush [MR] to select memory
mode, if necessary.
ePush [FUNC], then push
[SET](8) to enter to the channel
name programming mode.
This function transfers a memory channel’s contents to VFO
(or another memory/call channel). This is useful when searching for signals around a memory channel frequency and for
recalling the offset frequency, subaudible tone frequency etc.
INITIAL SET
[VOL]
D Memory/call ➾ VFO
• The character to be edited blinks.
rRotate [VOL] to select a character.
MR
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
FUNC
ENT
ENT
Y] to move the cursor to
tPush [Y
Z] to move the cursor to
right, [Z
left.
SET
• Up to 5 characters can be used for channel name.
• Usable characters are A–Z, 0–9, “space,” +, –, =, ✱, /, [, ] and :.
y Push [✱ ENT] (or [CLR]) to set the name and exit the channel name programming mode.
qSelect the memory (call) channel to be transferred:
➥ Push [MR] (or [CALL]) to select memory (call channel)
mode.
Y] or [Z
Z] to select the
➥ Push [Y
memory channel.
• When [VOL] is assigned as
tuning dial, rotate [VOL] to select the memory channel. (pgs.
18, 53)
wPush [FUNC], then push and
hold [MR] for 1 sec. to transfer
the selected memory contents
to the VFO.
• VFO mode is selected automatically.
[VOL]
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
MR
CALL
ENT
FUNC
10
11
12
13
14
15
16
17
18
19
28
6
MEMORY/CALL OPERATION
D Memory/call ➾ memory/call
D Clearing a memory
qSelect the memory (call) channel to be transferred:
➥ Push [MR] (or [CALL]) to select the memory (call channel) mode.
Y] or [Z
Z] to select the
➥ Push [Y
memory channel.
• When [VOL] is assigned as
tuning dial, rotate [VOL] to select the memory channel. (pgs.
18, 53)
wPush [FUNC], then push [MR]
momentarily.
[VOL]
qPush [CLR] to select VFO mode, if necessary.
wPush [FUNC], then push [MR] to enter the memory transfer mode.
• “X” and a memory channel
number blink.
Y] or [Z
Z] to select the
ePush [Y
memory channel to be cleared.
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
MR
CALL
ENT
• When [VOL] is assigned as tuning dial, rotate [VOL] to select the
memory channel. (pgs. 18, 53)
• The call channel cannot be
cleared.
FUNC
Y] or [Z
Z] to select the target memory.
ePush [Y
• When [VOL] is assigned as tuning dial, rotate [VOL] to select
the target channel. (pgs. 18, 53)
r Push [FUNC], then push and hold [MR] for 1 sec.
• Memory mode is selected and the contents are transferred to the
target memory.
CALL
MR
CLR
P.BEEP
T.SCAN
BANK
rPerform the following operation
within 1 sec, otherwise the
transceiver returns to the memory mode without clearing the
memory.
- Push [FUNC], then push [MR] momentarily.
- Push [FUNC], then push and hold [MR] for 1 sec.
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
• The contents of the selected memory are cleared.
t Push [CLR] to return to regular operation.
29
FUNC
TONE
DUP
• “--” and “X” blink.
MR
PWR
FUNC
6
MEMORY/CALL OPERATION
■ Memory bank selection
■ Memory bank setting
The IC-V85 has a total of 10 banks (A to J). Each memory
channel, 0 to 99, may be assigned to one of the banks for
easy memory management.
q Push [MR] to select memory mode, then select the desired
Y] or [Z
Z].
memory channel via [Y
Push
q Push [MR] to select memory mode.
MR
Push
MR
w Push [FUNC] and [BANK](#) to
enter memory bank selection.
[VOL]
w Push [FUNC] and [SET](8) to
enter SET MODE.
Y] or [Z
Z] several times
e Push [Y
until “bAk” appears.
[VOL]
• Bank indicator blinks.
PWR
e Rotate [VOL] to select the desired bank, A to J.
• Banks that have no programmed
contents are skipped.
BANK
PWR
FUNC
CALL
MR
CLR
P.BEEP
T.SCAN
BANK
SCAN
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
FUNC
ENT
TONE
DUP
r Rotate [VOL] to select the desired bank.
FUNC
SET
SKIP
OPT
PRIO
SET
H/M/L
ENT
r Push [✱ ENT] (or [CLR]) to select
the bank.
ENT
FUNC
• Indicator stops blinking.
Y] or [Z
Z] to select the channel in the bank.
t Push [Y
t Push [✱ ENT] (or [CLR]) to assign the channel to the bank
and return to regular memory condition.
y Repeat steps q to t to assign another memory channel
to the same or another bank.
• No channel numbers are displayed for memory bank operation.
y To return to regular memory condition, push [FUNC] and
[BANK](#) to enter memory bank mode, then push [✱ ENT]
(or [CLR]).
NOTE: Display type setting (pgs. 20, 53) in INITIAL SET
must be selected “FR,” otherwise the memory bank
operation cannot be performed.
MODE
10
11
12
13
14
15
16
17
18
19
30
6
MEMORY/CALL OPERATION
■ Transferring bank contents
Contents of programmed memory banks can be cleared or
transferred to another bank.
INFORMATION: Even if the memory bank contents are
cleared, the memory channel contents still remain programmed.
w Push [FUNC] and [SET](8) to
enter SET MODE.
Y] or [Z
Z] several times
e Push [Y
until “bAk” appears.
• Bank indicator appears.
q Select the desired bank contents to be transferred or erased.
➥ Push [MR] to select memory mode.
➥ Push [FUNC] and [BANK](#),
then rotate [VOL] to select the
desired memory bank.
[VOL]
• Bank indicator blinks.
[VOL]
PWR
r Rotate [VOL] to select the desired bank to receive the transferred information or erase the
bank contents.
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
FUNC
ENT
SET
• Select “– –” indication when erasing
the contents from the bank.
➥ Push [✱ ENT] (or [CLR]) to seY]
lect the bank then push [Y
Z] to select the desired
and [Z
contents.
• Bank indicator stops blinking.
BANK
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
ENT
FUNC
31
t Push [✱ ENT] (or [CLR]) to transfer or erase, and return to
regular memory mode.
y Repeat steps q to t for transferring or erasing an another bank’s contents.
7
DTMF MEMORY
■ Programming a DTMF code sequence
The transceiver has 16 DTMF memory channels (d0 to dF)
for storage of often-used DTMF code sequence of up to 24
digits. DTMF memories are used to store phone numbers or
control codes.
q Push [FUNC], then push [OPT](0) to enter OPTION SET MODE.
• Rotate [VOL] to select “dtm.OF,” if necessary.
Push
OPT
FUNC
tEnter the desired DTMF code sequence by pushing the
digit keys, [A], [B], [C], [D], [#] and [✱], in the desired
sequence.
• A maximum of 24 digits can be input.
• [✱] enters tone “E”, [#] enters tone “F.”
• If a digit is mistakenly input, push [MONI] or [PTT] momentarily
then repeat from step q.
w Push and hold [OPT](0) for 1 sec. to select the DTMF memory.
• One of “d0” to “dF” appears.
OPT
Push
MONI
for 1 sec.
eRotate [VOL] to select the desired DTMF memory.
rPush and hold [OPT](0) for 1 sec. to enter the DTMF programming mode.
• “_ _ _ _ _” appears.
• Programmed memories can be cleared in this way.
OPT
Push
for 1 sec.
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
yPush [MONI] or [PTT] to save the digits and exit the DTMF
programming mode.
• Programmed DTMF code sequence sounds when [MONI] is
pushed.
• Or after 24th digit is input, the transceiver automatically saves
the digits and returns to step w.
10
11
12
13
14
15
16
17
18
19
32
7
DTMF MEMORY
■ Transmitting a DTMF code
sequence
D Using a DTMF memory channel
• DTMF memory indication
The DTMF memory consists of 5 pages that are 1st to 5th,
6th to 10th, 11th to 15th, 16th to 20th and 21st to 24th digits.
• 1st page indication
• 2nd page indication
q Push [FUNC], then push [OPT](0) to enter OPTION SET MODE.
• Rotate [VOL] to select “dtm.OF,” if necessary.
Push
OPT
FUNC
w Push and hold [OPT](0) for 1 sec. to select the DTMF memory.
Appears
• 3rd page indication
• 4th page indication
OPT
Push
for 1 sec.
e Rotate [VOL] to select the desired memory.
r Push [MONI] or [PTT] to exit the DTMF memory mode.
Appears
• 5th page indication
Appears
• Selected DTMF code sequence sounds when [MONI] is pushed.
tWhile pushing [PTT], push [MONI] to transmit the selected
DTMF memory.
• After the DTMF code sequence is transmitted, the transceiver returns to receive automatically.
Blinks
33
7
DTMF MEMORY
■ DTMF transmission rate
D Manual DTMF code transmission
While pushing [PTT], push digit keys, [A], [B], [C], [D], [#]
and [✱] to transmit a DTMF code sequence manually.
• [✱] transmits tone “E”, [#] transmits tone “F.”
PWR
FUNC
CALL
MR
CLR
T.SCAN
BANK
TONE
P.BEEP
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
PRIO
SET
H/M/L
INITIAL SET MODE
USING
OPT
ENT
When slow DTMF transmission rates are required with DTMF
memory transmission (as for some repeaters), the transceiver’s rate of DTMF transmission can be adjusted.
[VOL]
Y]
qWhile pushing and holding [Y
Z], turn the power ON to
and [Z
enter INITIAL SET MODE.
Y] or [Z
Z] several times
wPush [Y
until “dtd” appears.
eRotate [VOL] to select the desired DTMF transmission rate.
• Four rates are available: “1” (100
msec. intervals) is the fastest; “5”
(500 msec. intervals) is the slowest.
PWR
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
rPush [✱ ENT] (or [CLR]) to exit INITIAL SET MODE.
ENT
10
11
12
13
14
15
16
17
18
19
34
8
SCAN OPERATION
■ Scan types
■ Programmed scan
Programmed scan repeatedly scans between two user programmed frequencies (memory channels “1A–3A” and
“1b–3b”) or scans between upper and lower band edges. This
scan is useful for checking for signals within a specific frequency range such as repeater output frequencies, etc.
Scans between lower (start) and high (stop) frequency.
PROGRAMMED SCAN
Band
edge
Start
1A
2A
3A
End
1b
2b
3b
Scan edges
Band
edge
Scan
Jump
Programmed scan P1 scans between 1A and 1b, P2 scans between 2A and 2b, and P3 scans between 3A and 3b frequencies.
Push
MEMORY (SKIP) SCAN
Mch 1
Mch 2
Mch 3
Mch 4
SKIP
Mch 0
Mch 99
Mch 10
Mch 6
SKIP
Mch 9
Mch 8
Mch 7
Priority channel
50 msec.
Priority memory channel scan
Mch 2
VFO frequency
145.20 MHz
5 sec.
35
Memory
scan
Push
Mch 4
Mch 5
Priority channels
Mch 99
ePush [FUNC] and [SET](8) several times to select the desired scan edge, “P1,” “P2,” “P3” or “AL.”
Mch 3
Mch 1
50 msec.
SCAN
• “AL” for full scan, “P1”, “P2” and “P3” for programmed scan between the programmed scan edge channels as “1A”–“1b,”
“2A”–“2b” and “3A”–“3b.”
Y] or [Z
Z].
• To change the scan direction, push [Y
• When [VOL] is assigned as tuning dial, rotate [VOL] to change
the scan direction. (pgs. 18, 53)
Priority memory channel watch
Mch 3
FUNC
Mch 5
PRIORITY WATCH
VFO frequency
145.20 MHz
5 sec.
q Push [CLR] to select VFO mode, if necessary.
wPush [FUNC] and [SCAN](5) to start a scan.
Mch 6
SKIP
SET
FUNC
r Push [CLR] to stop the scan.
SCAN OPERATION
■ Memory scan
NOTE: Scan edges, 1A–3A/1b–3b, must be programmed
in advance. Program them in the same manner as regular
memory channels. (p. 27)
If identical frequencies are programmed into the scan
edges, programmed scan will not proceed.
Memory scan repeatedly scans all programmed memory
channels, except those set as skip channels.
q Push [MR] to select memory mode, if necessary.
• “X” appears.
• See below to select bank scan.
w Push [FUNC] and [SCAN](5) to start the scan.
Y] or [Z
Z].
• To change the scan direction, push [Y
• When [VOL] is assigned as tuning dial, rotate [VOL] to change
the scan direction. (pgs. 18, 53)
Push
SCAN
FUNC
PWR
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
e Push [CLR] to stop the scan.
• Bank scan —Select the desired bank in step q above.
q Push [FUNC] and [BANK](#) to select memory bank mode.
w Rotate [VOL] to select the desired bank, A to J.
e Push [✱ ENT] (or [CLR]) to select the bank.
10
11
12
13
14
15
16
17
18
19
36
8
SCAN OPERATION
■ Skip channels
■ Scan resume condition
In order to speed up the scan rate, you can select memory
channels you don’t wish to scan as skip channels.
q Push [MR] to select memory mode, if necessary.
• “X” appears.
w Select a memory channel to set as a skip channel.
ePush [FUNC] and [SKIP](6) to toggle the skip setting ON
and OFF.
• “SKIP” appears when the channel is set as a skip channel.
“SKIP” appears
Push
SKIP
FUNC
USING
SET MODE
When a signal is received during scanning, the scan resume
condition determines what action the transceiver takes. The
transceiver has 2 scan resume conditions available as
illustrated below. Use SET MODE to select the one which best
suits your needs.
q Push [FUNC], then push [SET](8) to enter SET MODE.
Y] or [Z
Z] several times until “SCP” or “SCt” apwPush [Y
pears.
e Rotate [VOL] to select the desired scan resume condition.
• Pause scan:
When receiving a signal, scan pauses
on the signal until it disappears. Resumes 2 sec. after the signal disappears.
Pause scan
• Timer scan:
When receiving a signal, scan pauses
on the signal for 5 sec., 10 sec. or 15
sec., then resumes.
r Push [✱ ENT] (or [CLR]) to set and Timer scan
exit SET MODE.
37
8
SCAN OPERATION
■ Priority watch
Priority watch checks for signals on “priority channels” while
operating on a VFO frequency.
D Memory or call channel watch
While operating on a VFO frequency, memory or call channel
watch monitors for signals in the selected memory or call
channel every 5 sec.
q Select the desired memory channel or the call channel.
w Push [CLR] to select VFO mode.
e Push [FUNC], then push [PRIO](7) to start watching.
• VFO is displayed, then the decimal point “.”, on the frequency
readout blinks.
• The priority channel is monitored every 5 sec.
• When the signal is detected on the priority channel, the watching
is suspended according to the setting of the scan resume condition.
VFO frequency
D Memory scan watch
While operating on a VFO frequency, memory scan watch
monitors for signals in each memory channel in sequence,
every 5 sec.
q Push [MR] to select memory mode, if necessary.
• “X” appears.
wPush [FUNC], then push [SCAN](5) to start the memory
scan.
e Push [FUNC], then push [PRIO](7) to start the watching.
• VFO is displayed, then the decimal point “.”, on the frequency
readout blinks.
• When the signal is detected on the priority channel, the watching
is suspended according to the setting of the scan resume condition.
VFO frequency
Mch 3
Mch 2
Memory
scan
Mch 1
Memory channel
Mch 4
Mch 5
Priority channel
5 sec.
Mch 99
Mch 6
50 msec.
5 sec.
r Push [CLR] to stop watching.
50 msec.
r Push [CLR] to stop the watching.
SKIP
10
11
12
13
14
15
16
17
18
19
38
9
SUBAUDIBLE TONES
■ Tone squelch
D Operation
The tone squelch opens only when receiving a signal containing a matching subaudible tone. You can wait for calls
from group members using the same tone and not hear other
signals.
q Set the operating frequency.
• Set the volume and squelch to the desired level as the normal operation.
w Set the desired subaudible tone in SET MODE.
• See page 40 for programming.
e Push [FUNC], then push [TONE](1).
• Repeat several times until “ ” appears when selecting CTCSS,
or “ D ” appears when selecting DTCS.
Push
TONE
FUNC
• Recommended CTCSS frequencies
67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
(Unit: Hz)
156.7
162.2
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
• Recommended DTCS codes
CTCSS
DTCS
r When the received signal includes a matching tone,
squelch opens and the signal can be heard.
• When the received signal’s tone does not match, tone squelch
does not open, however, the S-indicator shows signal strength.
• To open the squelch manually, push and hold [MONI].
t Transmit in the normal way.
y To cancel the tone squelch, push [FUNC] and [TONE](1).
• Repeat several times until “ ” or “ D ” disappears.
39
NOTE: The transceiver has 50 tone frequencies and consequently their spacing is narrow compared to units having
38 tones. Therefore, some tone frequencies may receive
interference from adjacent tone frequencies.
To prevent interference from adjacent tone frequencies,
using the frequencies as in the following table, is recommended.
023
025
026
031
032
043
047
051
054
065
071
072
073
074
114
115
116
125
131
132
134
143
152
155
156
162
165
172
174
205
223
226
243
244
245
251
261
263
265
271
306
311
315
331
343
346
351
364
365
371
411
412
413
423
431
432
445
464
465
466
503
506
516
532
546
565
606
612
624
627
631
632
654
662
664
703
712
723
731
732
734
743
754
9
SUB AUDIBLE TONES
D Setting subaudible tones for tone squelch operation
Separate tone frequencies can be select for tone squelch operation rather than repeater operation (the same range of
tones is available— see right below). Like the repeater tones,
these are set in SET MODE.
q Select VFO or memory channel.
w Push [FUNC], then push [SET](8) to enter SET MODE.
Y] or [Z
Z] several times until “Ct” appears when see Push [Y
lecting CTCSS, or “dt” appears when selecting DTCS.
• “ ” blinks when selecting CTCSS, or “ D ” blinks when selecting
DTCS.
When SET MODE is selected from memory mode.
The tone squelch frequency is not stored in the selected
memory channel unless you follow steps y and u.
y Push [FUNC], then push and hold [MR] for 1 sec. to transfer the contents to VFO.
• 3 beeps are emitted.
• VFO mode is selected automatically.
u Push [FUNC], then push and hold [MR] for 1 sec.
• 3 beeps are emitted.
(unit: Hz)
• Available CTCSS tone frequency
CTCSS
DTCS
r Rotate [VOL] to select the desired subaudible tone.
t Push [✱ ENT] (or [CLR]) to program the selected tone and
exit SET MODE.
• The recommended CTCSS frequencies or DTCS codes are
shown at previous page.
67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
210.7
218.1
225.7
229.1
233.6
241.8
250.3
254.1
• Available DTCS codes
023
025
026
031
032
036
043
047
051
053
054
065
071
072
073
074
114
115
116
122
125
131
132
134
143
145
152
155
156
162
165
172
174
205
212
223
225
226
243
244
245
246
251
252
255
261
263
265
266
271
274
306
311
315
325
331
332
343
346
351
356
364
365
371
411
412
413
423
431
432
445
446
452
454
455
462
464
465
466
503
506
516
523
526
532
546
565
606
612
624
627
631
632
654
662
664
703
712
723
731
732
734
743
754
10
11
12
13
14
15
16
17
18
19
40
9
SUBAUDIBLE TONES
■ Pocket beep operation
This function listens for subaudible tones and can be used as
a “common pager” to inform you that someone has called
when you were away from the transceiver.
D Waiting for a call from a specific station
t When a signal with the matching tone is received, the
transceiver emits beep tones and blinks “ .”
• Beep tones sound for 30 sec. and “ ” blinks. To stop the beeps
manually, push any key. “ ” continues blinking until step y is
operated.
q Set the operating frequency.
w Set the desired CTCSS tone frequency or DTCS code in
SET MODE.
• See p. 40 for programming details.
CTCSS
e Push [FUNC], then push [TONE](1).
• Repeat several times until “ ” appears when CTCSS, or “ D ” appears when DTCS is selected.
Push
TONE
FUNC
CTCSS
DTCS
r Push [FUNC], then push [P.BEEP](2) to activate the pocket
beep function.
• “ ” appears.
Push
P.BEEP
FUNC
CTCSS
41
DTCS
DTCS
y Push [PTT] to answer.
• “ ” disappears and cancels the pocket beep function automatically.
SUB AUDIBLE TONES
■ Tone scan
By monitoring a signal on a repeater, or using pocket beep or tone
squelch function, you can determine the tone frequency necessary to
access a repeater or open the squelch.
q Set the frequency to be checked for a tone frequency or code.
w Push [FUNC], then push [TONE](1).
• Repeat several times to select the type of tone to be scanned. (One of “ ,”
“ ” or “ D ” appears)
• Tone scan may be used even if the tone condition or type is not selected.
Push
TONE
FUNC
e Push [FUNC], then push [T.SCAN](3) to start the tone scan.
Y] or [Z
Z].
• To change the scanning direction, push [Y
Push
T.SCAN
FUNC
r When the CTCSS tone frequency or DTCS code
is matched, the squelch opens and the tone frequency or code is temporarily programmed into
the selected mode such as memory or call channel.
• The tone scan pauses when a CTCSS tone frequency or 3-digit DTCS code is detected.
• The decoded CTCSS tone frequency or 3-digit DTCS
code is used for the tone encoder or tone encoder/decoder depending on the selected tone condition or
type in step w.
- No indication : Cannot be used for operation.
-“ ”
: CTCSS tone encoder
-“ ”
: CTCSS tone encoder/decoder
- “D ”
: DTCS tone encoder/decoder
t Push [CLR] to stop the scan.
10
11
12
13
14
15
16
17
18
19
42
10
PAGER/CODE SQUELCH
Requires Optional UT-108
■ Pager function
■ Code programming
This function uses DTMF codes for paging and can be used
as a “message pager” to confirm you of a caller’s identification
even when you leave the transceiver temporarily unattended.
D Before programming
Pager selective code (push [PTT])
Beep
Beep Beep
Answer back (manual)
The pager and code squelch functions require ID codes and a
group code. These codes are 3-digit DTMF codes and must
be written into the code channels before operation.
q Decide the ID code of each transceiver and a group code
for your group.
w Decide whether you want to return to normal operation or
code squelch operation after a connection is made.
e Program the ID code, group code and transmit codes
(other station’s codes) as below.
D Code channel assignment
ID OR
CODE CHANNEL
GROUP CODE
NUMBER
eep
p B
Bee Beep
Set both transceivers to either
code squelch or non-coded operation
Communication
43
“RECEIVE ACCEPT” OR
“RECEIVE INHIBIT”
Your ID code
Other parties’
ID code
1–6
“Receive inhibit” should be
programmed in each channel.
Group code
One of 1–6
“Receive accept” must be
programmed in one channel.
Memory space*
“Receive accept” only
“Receive inhibit” only.
*Channel CP automatically memorizes an ID code when receiving a
pager call. The contents in channel CP cannot be changed manually.
Optional UT-108 is required when using the pager/code squelch functions.
PAGER/CODE SQUELCH
10
D Code programming
Your ID code MUST be programmed into code channel C0.
Up to 6 transmit codes (codes that you transmit) are programmable into code channels, C1 to C6, if required.
q Push [FUNC], then push [OPT](0) to enter
MODE.
y Enter the desired 3-digit transmit code via the keypad.
OPTION SET
• Rotate [VOL] to select “dtm.PG” or “dtm.CS,” if “dtm.OF” appears.
u Push [FUNC], then push [SKIP](6) to set the channel to “receive inhibit” or “receive accept.”
• When “receive inhibit” is set, “SKIP” appears as below.
• Code channel C0 cannot be set as “receive inhibit.”
• See the table for “receive accept” and “receive inhibit” details
(p. 43).
or
w Push and hold [OPT](0) for 1
sec. to enter the code selection
mode.
• One of either “CP” or “C0” to “C6”
blinks.
• “C0” is your ID code and “C1” to “C6” are transmit codes.
Y]/[Z
Z]) to select code channel C0.
e Rotate [VOL] (or push [Y
• Each transceiver should have a different ID code.
r Enter the desired 3-digit ID
code via the keypad.
t Rotate [VOL] (or push
Y]/[Z
Z]) to select a transmit
[Y
code channel from C1 to C6.
i Repeat steps t and y to set additional transmit code
channels, if desired.
o Push [✱ ENT] (or [CLR]) to exit code selection mode.
• Receive accept/receive inhibit
➥ “Receive accept” (“SKIP” indicator does not appear) accepts pager calls when the transceiver receives a signal
with a code the same as that in the code channel.
➥ “Receive inhibit” (“SKIP” indicator appears) ignores calls
even when the transceiver receives a code the same as
that in the code channel. Transmit codes should therefore
be programmed for “receive inhibit,” otherwise the transceiver will not reject unnecessary calls.
10
11
12
13
14
15
16
17
18
19
44
10
PAGER/CODE SQUELCH
■ Pager operation
D Calling a specific station
q Program the code channel in advance (p. 44).
w Set the operating frequency.
• Set the volume and squelch to the desired level as in normal operation.
e Push [FUNC], then push [OPT](0).
• Rotate [VOL] to select “dtm.PG,” if “dtm.CS” or “dtm.OF” appears.
Push
OPT
FUNC
r Select the desired transmit code channel:
➥ Push and hold [OPT](0) for 1 sec. to enter the code selection mode.
Y]/[Z
Z]) to select the desired
➥ Rotate [VOL] (or push [Y
code channel.
➥ Push [✱ ENT] (or [CLR]) to return to previous mode.
• 100 MHz digit shows “P.”
t Push [PTT] to transmit the pager code.
y Wait for an answer back.
• When the transceiver receives an answer back code, the function display shows the other member’s ID or group code.
45
u After confirming a connection, push [FUNC] and [OPT](0)
to enter OPTION SET MODE, then rotate [VOL] to select the
code squelch operation “dtm.CS,” or non-selective calling
system “dtm.OF.”
• DO NOT push any digit keys while code channels C0 to C6 are
displayed, otherwise code channel contents will be changed.
i Communicate with the other party as normal: push [PTT]
to transmit; release to receive.
D Waiting for a call from a specific station
q Set the operating frequency.
w Push [FUNC], then push [OPT](0).
➥ Rotate [VOL] to select “dtm.PG,” if “dtm.CS” or
“dtm.OF” appears.
➥ Push [✱ ENT] (or [CLR]) to return to previous mode.
• 100 MHz digit shows “P.”
e Wait for a call.
• When receiving a call, the caller’s ID or group code appears as
shown at next page.
• DO NOT push any digit keys while code channels C0 to C6 are
displayed, otherwise code channel contents will be changed.
r Push [PTT] to send an answer back call and display the
operating frequency.
t After confirming a connection, push [FUNC] and [OPT](0)
to enter OPTION SET MODE, then rotate [VOL] to select the
code squelch operation “dtm.CS,” or non-selective calling
system “dtm.OF.”
PAGER/CODE SQUELCH
• PERSONAL CALLS
This display appears when you are called with your ID code
and the calling station’s ID code is 123.
“CP” and “
” blink.
• GROUP CALLS
This display appears when you are called with the group
code, 888, and 888 has been programmed into code channel
C6.
Code channel
• ERROR INFORMATION
When the transceiver receives an incomplete code, “E” and
previously received code appear.
Previously received code.
During channel number indication (described on page 20)
To use these functions in channel number indication, the
pager/code squelch setting must be programmed with other
memory contents before selecting channel number indication.
10
■ Code squelch
When using code squelch you will only receive calls from stations which know your ID or group code. A 3-digit code is sent
each time [PTT] is pushed in order to open the receiving station’s code squelch prior to voice transmission.
q Set the operating frequency.
• Set the volume and squelch to the desired level as in normal operation.
w Push [FUNC], then push [OPT](0).
• Rotate [VOL] to select “dtm.CS,” if “dtm.PG” or “dtm.OF” appears.
e Select the desired transmit code channel:
➥ Push and hold [OPT](0) for 1 sec. to enter code selection mode.
Y]/[Z
Z]) to select the desired
➥ Rotate [VOL] (or push [Y
code channel.
➥ Push[✱ ENT] (or [CLR]) to exit code selection mode and
return to previous mode.
• 100 MHz digit shows “C.”
r Operate the transceiver in the normal way (push [PTT] to
transmit; release [PTT] to receive).
t To cancel the code squelch, push [FUNC] and [OPT](0),
then rotate [VOL] to select “dtm.OF.”
• 100 MHz digit shows “1” when the function is cancelled.
10
11
12
13
14
15
16
17
18
19
46
11
SET MODES
■ SET MODE
D Entering SET MODE
D Repeater tone frequency
q Push [FUNC], then push [SET](8) to enter SET MODE.
Y] or [Z
Z] to select the desired item.
w Push [Y
e Rotate [VOL] to select the condition/value.
Selects tone encoder frequency for accessing a repeater, etc.
from one of 50 available frequencies.
• 67.0–254.1 Hz (50 tones): 88.5 Hz (default)
• To exit SET MODE, push [✱ ENT] (or [CLR]).
Enter
Set
Exit
[VOL]
D Tone squelch frequency
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
Selects frequency for tone squelch or pocket beep operation
from one of 50 available frequencies.
• 67.0–254.1 Hz (50 tones): 88.5 Hz (default)
FUNC
SKIP
OPT
PRIO
SET
H/M/L
ENT
ENT
SET
NOTE: When the display type setting (pgs. 16, 65) in INITIAL SET MODE is selected other than “FR” (“CH” or “nm”)
and accessing SET MODE from memory mode, most of set
mode items are restricted.
47
• Available subaudible tone frequencies
67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
210.7
218.1
225.7
229.1
233.6
241.8
250.3
254.1
SET MODES
11
D DTCS code
D Offset frequency
Selects DTCS (both encoder/decoder code) for DTCS
squelch operation. Total of 104 codes are available.
• 023–754: 023 (default)
Sets the duplex offset frequency within 0 to 20 MHz range.
During duplex (repeater) operation, transmit frequency (or receive when reverse function is set to ON) shifts the set frequency. (default value may differ depending on transceiver
types and versions)
D DTCS polarity
Selects DTCS polarities for transmission and reception from
“nn (default),” “nR,” “Rn” and “RR.” (n: normal/R: reverse)
D Reverse function
Turns the reverse function ON and OFF (default).
D Tuning step
Selects tuning step from 5, 10, 12.5, 15, 20, 25, 30 and
Y]/[Z
Z] or [VOL] (When [VOL] is assigned as tuning
50 kHz for [Y
dial) operation. (default value may differ depending on transceiver types and versions)
Reverse function OFF
Reverse function ON
10
11
12
13
14
15
16
17
18
19
48
11
49
SET MODES
D Scan pause timer
D LCD backlight
Selects the scan pause time from SCt.5, SCt.10, SCt.15 and
SCP. 2. When receiving signals, the scan pauses according
to the scan pause time.
• SCt. 5/10/15 : Scan pauses for 5/10/15 sec.
(default: SCt.15)
• SCP. 2
: Scan pauses until the signal disappears. Resumes 2 sec. after the signal disappears.
Selects LCD backlight lighting condition from auto, ON and
OFF.
• LIG.At : Lights when any key except [PTT] is pushed. (default)
• LIG.ON : Lights continuously while the transceiver is powered ON.
• LIG.OF : Never lights.
D Function key timer
D Transmission permission
Selects the function indicator display timer (when pushed
[FUNC]) from F0.At, F1.At, F2.At, F3.At and F .m.
• F0.At
: “ F ” disappears immediately after secondary function is operated. (default)
• F1/2/3.At: “ F ” disappears after 1/2/3 sec. after secondary
function is operated.
• F .m
: “ F ” appears until [FUNC] is pushed again.
Turns transmission permission ON and OFF. This function
can be set for each memory and call channel, independently.
• tX .On : Transmission is permitted. (default)
• tX .OF : Transmission is inhibited.
SET MODES
11
D Memory bank setting
Sets the desired memory bank (A to J and OFF) to assign the
regular memory channels.
This item appears when SET MODE is accessed from memory
mode only.
D Memory bank link function
Sets the memory bank link function ON and OFF (default).
The link function provides continuous banks scan, scanning
all contents in the selected banks during bank scan.
This item appears when SET MODE is accessed from memory
mode only.
• Bank link setting
q Rotate [VOL] to select the memory bank link function ON.
Y] or [Z
Z] to select the desired bank to be linked.
w Push [Y
• bLA: Bank A, bLb: Bank B, bLC: Bank C, bLd: Bank D,
bLE: Bank E, bLF: Bank F, bLG: Bank G, bLH: Bank H,
bLI: Bank I, bLJ: Bank J
e Rotate [VOL] to “ON” to link the bank.
r Repeat steps w and e to link other banks.
D Weather alert function
USA version only
Turns weather alert function ON and OFF (default).
10
11
12
13
14
15
16
17
18
19
50
11
SET MODES
■ INITIAL SET MODE
AT
POWER ON
The INITIAL SET MODE is accessed at power on and allows you
to set seldom-changed settings. In this way, you can “customize” transceiver operations to suit your preference and operating style.
D Entering INITIAL SET MODE
Y] and [Z
Z], turn power ON.
q While pushing and holding [Y
Y] or [Z
Z] to select the desired item.
w Push [Y
e Rotate [VOL] to select the condition or value.
• To exit INITIAL SET MODE, push [✱ ENT] (or [CLR]).
Enter
Set
Exit
[VOL]
51
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
SCAN
D Time-out timer
To prevent accidental prolonged transmission, etc., the transceiver has a time-out timer. This function cuts a transmission
OFF after 1–30 min. of continuous transmission. This timer
can be cancelled.
• tOt.OF : The time-out timer is turned OFF.
• tOt. 1–30: The transmission is cut OFF after the set period
elapses. (default: 3)
CALL
NOTE: The pocket beep level (Beep level 1 to 3 or OFF)
also changes as this setting.
PWR
PWR
FUNC
DUP
D Key-touch beep
Turns key-touch beep emission ON (Beep level 1 to 3) or
OFF.
(default: 3)
SKIP
OPT
PRIO
SET
H/M/L
ENT
ENT
• BE CAREFUL! The transceiver will become hot when
this time-out timer function is turned OFF and transmission is made for long periods.
• NOTE: When the battery pack (BP-227) becomes hot
from continuous transmittion, etc., the battery’s protection
circuit may activate to protect the battery itself and then
shut off the transceiver power until it has cooled down.
SET MODES
D Auto repeater
USA version only
The auto repeater function automatically turns ON or OFF the
duplex operation and tone encoder. The offset and repeater
tone is not changed by the auto repeater function. Reset
these frequencies, if necessary.
• RPt.OF : The auto repeater function is turned OFF.
• RPt.R1 : Activates for duplex only. (default)
• RPt.R2 : Activates for duplex and tone.
11
D Auto power-off
The transceiver can be set to automatically turn OFF after a
specified period with a beep when no key operations are performed.
• 30 min., 1 hour, 2 hours and OFF (default) can be specified.
The specified period is retained even when the transceiver
is turned OFF by the auto power-off function. To cancel the
function, select “POF.OF” in this SET MODE.
D Repeater lock-out
Selects lockout type from repeater, busy and OFF.
• RLO.OF : No lockout is activated. (default)
• RLO.RP : The repeater lockout is turned ON.
• RLO.bU : The busy lockout is turned ON.
10
11
12
13
14
15
16
17
18
19
52
11
SET MODES
D Squelch delay
D Dial assignment
Selects squelch delay from short and long to prevent repeated opening and closing of the squelch during reception
of the same signal.
• Sqt. S : The squelch closes in short delay. (default)
• Sqt. L : The squelch closes in long delay.
Selects [VOL] control action from volume and tuning dial.
• tOP.VO: AF volume (default)
• tOP.dI : Tuning dial
D Display type
D DTMF rate
The rate at which DTMF memories send individual DTMF
characters can be set to accommodate operating needs.
• 1: 100 msec. interval; 5.0 cps rate (default)
• 2: 200 msec. interval; 2.5 cps rate
• 3: 300 msec. interval; 1.6 cps rate
• 5: 500 msec. interval; 1.0 cps rate
(cps=characters/sec.)
Selects LCD indication type from frequency, channel number
and channel names.
• dSP.FR : Shows frequency (default)
• dSP.CH : Shows channel number*
• dSP.nm : Shows channel names†
*Only memory channels can be selected.
†
Frequency indication will be displayed when the selected memory
channel has no programmed memory name.
NOTE: When this setting is selected other than “FR” (“CH”
or “nm”) and accessing SET MODE from memory mode,
most of set mode items are restricted.
53
SET MODES
11
D LCD contrast
D Power save
Selects LCD contrast from auto, high and low.
• LCd.At : Automatic (default)
• LCd.HI : High contrast
• LCd.LO : Low contrast
Selects duty cycle for power save function from auto, 1:32,
1:16, 1:8, 1:2 and OFF.
• P–S.At : Duty cycle changes automatically. (default)
• P–S.32 : 1:32 duty cycle
• P–S.16 : 1:16 duty cycle
• P–S. 8 : 1:8 duty cycle
• P–S. 2 : 1:2 duty cycle
• P–S.OF : The power save function is turned OFF.
NOTE: During pager or code squelch operation (with UT108), the active duty cycle is fixed 1:1 only (even for duty
cycle settings other than OFF).
10
11
12
13
14
15
16
17
18
19
54
11
SET MODES
D Monitor key action
The monitor key, [MONI], can be set as a ‘sticky’ key. When
set to the sticky condition, each push of [MONI] toggles the
monitor function ON and OFF.
• PU (Push) : Pushing and holding [MONI] to monitor the frequency. (default)
• HO (Hold) : Push [MONI] to monitor the frequency and push
again to cancel it.
D Tuning speed acceleration
The tuning speed acceleration automatically speeds up the
Y] or [Z
Z], or rotattuning speed when pushing and holding [Y
ing [VOL] rapidly.*
• S–S.At : The tuning speed acceleration is activated. (default)
• S–S. m : The tuning speed acceleration is not activated.
*When tuning dial is assigned with [VOL].
D Mic simple mode
Optional HM-75A required
This item turns the microphone simple mode ON and OFF.
Microphone simple mode is used to change the function assignments for keys in the optional HM-75A REMOTE CONTROL
SPEAKER-MICROPHONE as below. This assignment is convenient for 3-channel use of simple operation.
• mIC.n1 : Normal 1 (default)
• mIC.n2 : Normal 2
• mIC.Sm: Simple mode
HM-75A
Mode
key
NORMAL2
SIMPLE
[A]
Freq.
CH
NORMAL1
[CALL]
Null
[MONI]
[MONI]
[B]
Freq.
CH
VFO/Memory
Null
VFO/Memory
Null
[CALL]
Y]
[Y
Freq.
CH
Freq. Up
Memory CH Up
Freq. Up
Memory CH Up
MR-00CH
Z]
[Z
Freq.
Freq. Down
Freq. Down
CH Memory CH Down Memory CH Down
MR-01CH
A 1750 Hz tone can be transmitted with the HM-75A operation.
➥ Push [A] while pushing [PTT].
55
SET MODES
11
D Battery protection function
NOTE:
Turn power OFF when connecting the HM-75A to the
transceiver.
VFO mode cannot be selected via the microphone when
SIMPLE mode is selected.
Sets the Battery protection function from LI (Li-Ion) (default)
and OFF.
LI(Li-Ion):
➥ The transceiver does not memorized the transceiver
ON/OFF condition when battery is detached, and automatically returns to OFF condition even if you detach the battery with the transceiver ON condition. You are required to
turn ON the transceiver by pushing [PWR] for every battery attach.
➥ Beep sounds when the attached battery is exhaustion.
• The battery must be charged presently.
OFF : The transceiver memorizes the transceiver ON/OFF
condition when battery is detached.
NOTE: This item MUST be set “LI” (Li-Ion) when the attaching battery is BP-227 (Li-Ion).
10
11
12
13
14
15
16
17
18
19
56
12
SET MODE INSPECTION
Push
SET
FUNC
, then push
to enter SET MODE (p. 47).
SET MODE
• Repeater tone
frequency (p. 47)
• Tone squelch
frequency (p. 47)
• DTCS code (p. 48)
• DTCS polarity (p. 48)
• Weather alert* (p. 50)
• Tuning step (p. 48)
• Offset frequency (p. 48)
: Push
: Push
• Bank link function†
(p. 50)
*Available for [USA] version only.
†
Appears when accessing SET MODE from memory mode only.
• Reverse function
(p. 48)
NOTE: When the display type setting (pgs. 20, 53) in INITIAL
SET MODE is selected other than “FR” (“CH” or “nm”) and
accessing SET MODE from memory mode, most of set mode
items are restricted.
• Bank setting†
(p. 50)
57
• Tx permission
(p. 49)
• LCD backlight
(p. 49)
• Function key timer
(p. 49)
• Scan pause timer
(p. 49)
SET MODE INSPECTION
While pushing and holding
, push
PWR
12
to enter INITIAL SET MODE (p. 51).
INITIAL SET MODE
• Key touch beep (p. 51)
• Time-out timer (p. 51)
• Auto repeater* (p. 52)
• Auto power-off (p. 52)
• Battery protection function (p. 56)
• Repeater lock-out (p. 52)
• Squelch delay (p. 53)
: Push
• Mic simple mode (p. 55)
• DTMF rate (p. 53)
: Push
*Available for [USA] version only.
• Tuning speed acceleration (p. 55)
• Monitor key action (p. 55)
• Dial assignment (p. 53)
• Power save (p. 54)
• LCD contrast (p. 54)
• Display type (p. 53)
10
11
12
13
14
15
16
17
18
19
58
13
CLONING
Cloning allows you to quickly and easily transfer the programmed contents from one transceiver to another transceiver.
■ Transceiver-to-transceiver cloning
q Connect the OPC-474 CLONING CABLE to the [SP] jack of
the master and sub-transceivers.
• The master transceiver is used to send data to the sub-transceiver.
POWER ON
AT
Y], turn power ON to enter
w While pushing [FUNC] and [Y
cloning mode (master transceiver only— power ON for
sub-transceiver).
• “CLONE” appears and the
transceivers enter the clone
standby condition.
PWR
PWR
Master transceiver
Sub transceiver
59
FUNC
CALL
MR
CLR
T.SCAN
BANK
TONE
P.BEEP
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
ENT
FUNC
CLONING
13
■ Cloning using a PC
Please refer to the HELP file that comes with CS-V85
CLONING SOFTWARE.
e Push [PTT] on the master
transceiver.
OPC-478
(RS-232C type)
• “CL OU” appears in the master
transceiver’s display and Smeter indicator shows that
data is being transferred to
the sub-transceiver.
OPC-478UC
(USB type)
to RS-232C port
to USB port
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
OPT
PRIO
SET
H/M/L
OPC-478U
(USB type)
to USB port
ENT
• “CL In” appears automatically in the sub-transceiver’s display and
S-meter indicator shows that data is being received from the
master transceiver.
r When cloning is finished, turn power OFF, then ON again
to exit cloning mode.
NOTE: DO NOT push [PTT] on the sub-transceiver during
cloning. This will cause a cloning error.
TRANSCEIVER
PC
10
11
12
13
14
15
16
17
18
19
60
14
RESETTING FUNCTIONS
■ Partial reset
AT
POWER ON
If you want to initialize the operating conditions (VFO frequency, VFO settings, set mode contents) without clearing
the memory contents, a partial resetting function is available
for the transceiver.
➥ While pushing [CLR], push and hold [PWR] for 1 sec. to
partially reset.
■ CPU reset
AT
POWER ON
The function display may occasionally display erroneous information (e.g. when first applying power). This may be
caused externally by static electricity or by other factors.
If this problem occurs, turn power OFF. After waiting a few
seconds, turn power ON again. If the problem persists, perform the following procedure.
• Partial resetting is also available. See left for details.
IMPORTANT!:
Resetting the transceiver CLEARS all memory information
and initializes all values in the transceiver.
PWR
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
PRIO
SET
H/M/L
➥ While pushing [MONI] and [CLR], push and hold [PWR]
for 1 sec. to reset the CPU.
• “CLEAR” indicates, then initial display appears.
CLR
OPT
ENT
PWR
MONI
61
PWR
FUNC
CALL
MR
CLR
TONE
P.BEEP
T.SCAN
BANK
DUP
SCAN
SKIP
PRIO
SET
H/M/L
OPT
ENT
CLR
TROUBLESHOOTING
15
If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center.
PROBLEM
No power comes ON.
POSSIBLE CAUSE
• The batteries are exhausted.
• The battery polarity is reversed.
• The BP-227 becomes hot.
(Battery’s protection circuit may activate.)
SOLUTION
REF.
• Replace the batteries or charge the battery pack. pgs. 9, 13–15
• Check the battery polarity.
p. 10
• Cool down the BP-227.
–
• Rotate [VOL] to suitable level.
No sound comes from the • Volume level is too low.
• Different tone is selected with tone/DTCS • Check the tone using tone/DTCS scan.
speaker.
squelch.
Transmitting is impossible. • The batteries are exhausted.
p. 19
p. 42
• Replace the batteries or charge the battery pack. pgs. 9, 13–15
p. 42
No contact possible with • Different tone is selected with tone/DTCS • Check the tone/DTCS using tone scan.
squelch.
another station.
Frequency can not be set. • The key lock function is activated.
• Memory mode or call channel is selected.
• Push [FUNC] then push and hold [
for 1 sec. to cancel the function.
• Push [CLR] to set VFO mode.
](✱
ENT)
p. 20
p. 17
p. 17
• Push [CLR] to set VFO mode.
Program scan function • Memory mode or call channel is selected.
• Same frequencies are programmed both “✱A” • Programming different frequencies in “✱A” and p. 27
can not start.
“✱b” respectively.
and “✱b” of scan edge memory channel.
• Push [MR] to set memory mode.
Memory scan function can • VFO mode or call channel is selected.
• The programmed memory channel is only • Program more than 2 memory channels.
not start.
one.
p. 26
p. 27
The displayed frequency is • The CPU malfunctioned.
• External factors caused a fault.
erroneous.
p. 61
• Reset the transceiver.
• Remove and re-attach the battery pack or battery p. 9
case.
Can not charge the battery • Turn the transceiver’s power ON.
with BC-167A/D.
• Turn the transceiver’s power OFF, then connect pgs. 13 ,17
the BC-167A/D to charge.
10
11
12
13
14
15
16
17
18
19
62
16
OPTION
■ Optional UT-108 installation
q Remove the optional connector access cover (named 2251
OPT sheet).
• Insert a screwdriver into the hollow of the chassis, then lift and
take away the cover. (The removed cover cannot be used
again.).
w Attach the optional unit. Insert the connector firmly to avoid
a bad contact.
• Remove the paper baking of the optional unit before installing.
WARNING!
NEVER attempt to remove the optional connector cover
using your finger nails, this may result in injury.
63
e Remove the paper backing of 2251 OPT sheet supplied as
an accessory.
r Attach the new 2251 OPT sheet to the service window.
t Program the necessary information from the transceivers
keypad or using the cloning software, before operation.
SPECIFICATIONS
■ General
■ Transmitter
• Frequency coverage
: (unit: MHz)
USA
Tx: 144–148/Rx: 136–174*1
Europe, UK
Tx: 144–146/Rx: 136–174*2
Taiwan, Thailand, Korea
Tx/Rx: 144–146
General (LM)
Tx/Rx: 136–174*1
*1: Guaranteed: 144–148 MHz range only
*2: Guaranteed: 144–146 MHz range only
• Type of emission
: FM
• Number of memory channels : 107 (incl. 6 scan edges and 1 call)
• Frequency resolution
: 5, 10, 12.5, 15, 20, 25, 30, 50 kHz
• Operating temperature range : –10°C to +60°C; +14˚F to +140˚F
• Frequency stability
: ±2.5 ppm
• Modulation system
• Output power (at 7.2 V)
[Thailand]
[Others]
• Max. frequency deviation
• Spurious emissions
• Microphone connector
17
(without battery pack and Ant.)
10
11
12
13
14
15
16
17
18
19
All stated specifications are subject to change without notice or obligation.
64
(–10°C to +60°C; +14˚F to +140˚F)
• Power supply requirement
: Supplied (or optional) Icom’s battery
pack or 11.0 V±15% external DC power
• Current drain
: (at 7.2 V DC: approx.)
Transmit
at 7 W (High) 2.6 A
at 4 W (Middle) 2.0 A
at 0.5 W (Low) 1.0 A
Receive
standby
80 mA
power save
30 mA
max. audio
250 mA
• Antenna connector
: BNC (50 Ω)
• Dimensions (proj. not included) : 56(W) × 110(H) × 34.4(D) mm
27⁄32(W)×411⁄32(H)×111⁄32(D) in
■ Receiver
• Receive system
: Double-conversion superheterodyne
• Intermediate frequencies
: 1st: 46.35 MHz, 2nd: 450 kHz
• Sensitivity (at 12 dB SINAD)
: Less than 0.2 µV
• Squelch sensitivity (threshold) : Less than 0.16 µV
• Selectivity
: More than 55 dB
• Spurious and image rejection : More than 60 dB
• Intermodulation
: More than 55 dB
• Audio output power
: More than 0.3 W at 10% distortion with
(at 7.2 V DC)
• Ext. speaker connector
(with BP-227)
• Weight (approx.)
: Variable reactance frequency mod.
5.5 W/4 W/0.5 W (High/Mid/Low)
7 W/4 W/0.5 W (High/Mid/Low)
: ±5.0 kHz
: Less than –60 dBc
: 3-conductor 2.5 (d) mm (1⁄10″)/2.2 kΩ
: 310 g; 12.5 oz
(with BP-227 and Ant.)
165 g; 5.8 oz
an 8 Ω load
: 3-conductor 3.5 (d) mm (1⁄8″)/8 Ω
18
CE
ABOUT CE
Versions of the IC-V85E which display the
“CE” symbol on the serial number seal,
comply with the essential requirements of
the European Radio and Telecommunication Terminal Directive 1999/5/EC.
This warning symbol indicates that this
equipment operates in non-harmonised frequency bands and/or may be subject to licensing conditions in the country of use.
Be sure to check that you have the correct
version of this radio or the correct programming of this radio, to comply with national licensing requirement.
65
INSTALLATION NOTES
• When transmitting with a portable radio, hold the radio in a
vertical position with its microphone 2.5 to 5 centimeters
away from your mouth. Keep antenna at least 2.5 centimeters from your head and body.
• If you wear a potable two-way radio on your body, ensure
that the antenna is at least 2.5 centimeters from your body
when transmitting.
CE
DOC
DECLARATION
OF CONFORMITY
We Icom Inc. Japan
1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan
Declare on our sole responsibility that this equipment complies with the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1995/5/EC, and that any applicable Essential Test
Suite measurements have been performed.
16th Nov. 2006
Place and date of issue
Kind of equipment:
FM TRANSCEIVER
Type-designation:
iV85E
Himmelgeister straße 100
D-40225
Version (where applicable):
Icom (Europe) GmbH
Authorized representative name
H. IKegami
General Manager
This compliance is based on conformity with the following harmonised
standards, specifications or documents:
i)
ii)
iii)
iv)
EN 301 489-1 v 1.4.1 (2002-08)
EN 301 489-15 v 1.2.1 (2002-08)
EN 301 783 v 1.1.1 (2000-09)
EN 60950-1 (2001): A11: 2004
Signature
18
10
11
12
13
14
15
16
17
18
19
66

#02 Europe
■ GER ■ FRA ■ ESP ■ SWE
#22 Europe-1 ■ AUT ■ NED ■ POR ■ DEN
■ GBR ■ BEL ■ ITA
■ FIN
■ IRL
■ LUX ■ GRE ■ SUI
■ NOR
#23 UK

■ GER ■ FRA ■ ESP ■ SWE
■ AUT ■ NED ■ POR ■ DEN
■ GBR ■ BEL ■ ITA
■ FIN
■ IRL
■ LUX ■ GRE ■ SUI
■ NOR
A-6552D-1EX
Printed in Japan
© 2006 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Page Count                      : 80
Page Mode                       : UseThumbs
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:5c50df1b-1cea-46b7-ba4d-ad56fbc8b771
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Create Date                     : 2006:11:15 08:55:05Z
Modify Date                     : 2007:01:04 11:21:33-05:00
Metadata Date                   : 2007:01:04 11:21:33-05:00
Document ID                     : uuid:f17ed5c9-d227-44ac-93f2-0a7ed7765d43
Format                          : application/pdf

EXIF Metadata provided by EXIF.tools