ID TECH PISCES PISCES User Manual ViVOpay 8800 User Guide

Download:
Mirror Download [FCC.gov]
Document ID	3292941
Application ID	TPs+U9PYc4QWbyqg6Ge5+A==
Document Description	Users Manual
Short Term Confidential	Yes
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	86.13kB (1076636 bits)
Date Submitted	2017-02-23 00:00:00
Date Available	2017-08-23 00:00:00
Creation Date	2017-01-06 11:50:24
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2017-01-06 11:50:24
Document Title	ViVOpay 8800 User Guide.book
Document Creator	Microsoft® Office Word 2007
Document Author:	sbaird

PISCES - POS PIN PAD
User Guide
Copyright
Copyright 2016, International Technologies and Systems Corporation. All rights reserved.
ID TECH
10721 Walker Street
Cypress, CA 90630
USA
This document, as well as the hardware and software it describes, is furnished under license and may only be
used in accordance with the terms of such license. The content of this paper is furnished for informational
use, subject to change without notice, and not to be construed as a commitment by ID TECH. ID TECH
assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.
Except as permitted by such license, no part of this publication may be reproduced or transmitted by
electronic, mechanical, recorded, or any other method, or translated into another language or language
form without the express written consent of ID TECH. ID TECH is a registered trademark of International
Technologies and Systems Corporation. ViVOpay and Value through Innovation are trademarks of
International Technologies and Systems Corporation. Other trademarks are the property of the respective
owner.
Warranty Disclaimer: The services and hardware are provided "as is" and "as-available" and the use of these
services and hardware are at the user’s own risk. ID TECH does not make, and hereby disclaims, any and all
other express or implied warranties, including, but not limited to warranties of merchantability, title, fitness
for a particular purpose, and any warranties arising from any course of dealing, usage, or trade practice. ID
TECH does not warrant that the services or hardware will be uninterrupted, error-free, or completely secure.
FCC Regulatory Compliance
Notices Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. This device complies with part 15
of the FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and the receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to the ViVOpay PISCES not expressly approved by ID TECH could void the user's
authority to operate the ViVOpay PISCES.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired
operation of the device.
Cautions and Warnings
Caution: The ViVOpay PISCES should be mounted 1 foot (30 cm) away from other
ViVOpay PISCES. Can be adjusted based on lane setup.
Caution: Danger of Explosion if battery is incorrectly replaced. Replace only with
same or equivalent type recommended by the manufacturer. Discard used batteries
according to the manufacturer’s instructions.
Warning: Avoid close proximity to radio transmitters which may reduce the ability
of the reader.
Table of Contents
Chapter 1
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking the ViVOpay PISCES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 2
Installing the ViVOpay PISCES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Site Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
PCI PED Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Verifying PCI Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Radio Frequency Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing the ViVOpay PISCES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting the ViVOpay PISCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Accessing the Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting Power, and Data Cables . . . . . .. . . . . . . . . . . . . . . . . . . 6
Testing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Transaction Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 3
Troubleshooting and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Onboard Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Replacing the Stylus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Upgrading the Firmware. . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Appendix A
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 13
ViVOpay PISCES Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ViVOpay 8850 User Guide
15
iv
Chapter 1
Getting Started
Overview
The ViVOpay PISCES seamlessly integrates with existing POS systems and requires minimal
counter space at checkout stands. The ViVOpay PISCES is a PCI 4.1 certified counter-top
contactless reader with integrated color display, MSR, signature capture and PIN pad. This device
features serial RS-232 and USB 2.0 communications to POS systems.
ViVOpay PISCES supports the following contactless payment applications:
Support for Apple Pay VAS L1 protocol
Support for Google Android Pay/ SmartTap
Support for Samsung Pay
Support for Mifare cards:
Mifare classic
Mifare Ultralight
Mifare DESFire EV1
Support for Secure SoftSAM(s)
Support for Payment Card Brands:
VISA – VCPS MSD, qVSDC
MasterCard – MCL
AMEX – Expresspay
Discover –DPAS
Interac flash
JCB
China Union Pay(International)
This document assumes that users are familiar with their host POS systems and all related functions.
Features
The following features are supported:
•
•
•
•
•
•
•
•
•
•
PCI 4.1 certified
ISO14443 type A/B and Mifare based contactless payment transactions
ISO 18092 support for peer-to-peer NFC devices and smartphones
Support for NFC devices
PIN entry for PIN debit transactions
Magnetic stripe card transactions
Electronic signature capture
Three SAM card slot provided.
One SD card slot provided
RJ-45 connector at User
ViVOpay PISCES User Guide
Getting Started
Unpacking the ViVOpay PISCES
The ViVOpay PISCES requires a data cable and a power supply if the data cable is not supplying
power. Data cable and power supply are not included with the ViVOpay PISCES and should be
purchased separately from TDTECH. Verify that you have all the required components for the
installation.
PISCES (P/N:IDPP-138)
Data cable (varies by POS and length)
• Serial Data Cable (P/N 80143236-00X)
• USB Data Cable (P/N 80143234-00X)
• USB and RJ-45 Data Cable (P/N 80143235-00X)
These cables are recommended and approved by
ViVOtech to comply with FCC rules and regulations.
Power supply, if required
(P/N AC005R)
This power supply recommended and approved by
ViVOtech to comply with FCC rules and regulations.
You may also need the following:
•
Additional SAM card
•
Contactless test card (ViVOcard Contactless Test Card P/N 241-0015-03)
•
Magnetic stripe test card
The ViVOtech data cables and power supply are specifically designed to meet FCC requirements. If
you are using other cables or power supply, you must install ferrites available from ViVOtech. For
your free ferrite core kit with installation instructions, please contact ViVOtech support.
ViVOpay PISCES User Guide
Chapter 2
Installing the ViVOpay PISCES
Overview
Before you connect and mount the ViVOpay PISCES, you should plan the installation to conform to
PCI 4.1 requirements and minimize radio frequency interference. Once you have determined the
location and mounting of the ViVOpay PISCES, you can connect it to power and the POS terminal.
Finally, you should test the ViVOpay PISCES to make sure the installation is successful.
Site Planning
Two environmental considerations affect how you install the ViVOpay PISCES. PCI certification
has specific restrictions on how the reader is positioned to prevent PIN theft. You should also
consider objects and devices near the reader that may affect the performance of the contactless
radio frequency antenna.
PCI PED Compliance
The ViVOpay PISCES is a PCI 4.1 certified PIN/Debit payment device. PCI 4.1 certification requires
that sufficient protection be provided to ensure that entering a PIN number CANNOT be viewed by a
third party (such as another customer standing nearby, the cashier, or a security camera).
The ViVOpay PISCES has design elements, such as a recessed keypad, that meet some of
these requirements. However, to fully implement PCI 4.1 make sure you consider the following.
1. The ViVOpay PISCES must be in a location that will NOT force a customer to enter a PIN
that can be viewed by a third party (for example, a customer must tilt or rotate the device
for better accessibility due to objects blocking a card swipe).
2. If the ViVOpay PISCES is elevated on a mounting stand, shielding must be provided on
the mount to prevent a PIN being viewed by a third party.
3. If the ViVOpay PISCES is mounted on a counter top, additional shielding (which can
include other devices such as a cash register as long as conditions in (1) above is met)
must be provided to ensure that the PIN cannot be viewed by a third party (including
cashier and security camera).
WARNING: PCI requires that the device be mounted so that the PIN entry cannot be
observed by a third party (such as another customer standing in line, the cashier at the
counter, or a security camera mounted in the ceiling to observe the cash register area). If
the PIN entry can be observed, the store owner may be responsible for any losses
incurred by the customer if it can be determined that the customer’s PIN was stolen at
this location.
Verifying PCI Compliance
Before completing the installation, you must verify the ViVOpay PISCES is positioned so that the
PIN entry is not visible to other customers, the cashier behind the counter, or video surveillance
cameras. If PIN entry is visible, the ViVOpay PISCES must be repositioned or shielding added until
PIN entry cannot be observed.
These tests usually require at least two people—one to simulate entering the PIN while the other
attempts to view the keypad.
ViVOpay PISCES User Guide
Installing the ViVOpay PISCES
ESS
Can Another Customer View the PIN?
While one person stands at the ViVOpay PISCES with their hand positioned to enter the PIN, the
other tester should try to observe the keypad from behind and beside the first person.
Can the Cashier View the PIN?
While one person stands at the ViVOpay PISCES with their hand positioned to enter the PIN, the
other tester should stand behind the counter and try to observe the PIN keypad. The second tester
should move around a little to see if there is a position where they can observe PIN entry.
Can the Video Camera View the PIN?
While one person stands at the ViVOpay PISCES with their hand positioned to enter the PIN, the
other tester should observe what is being recorded by any video camera with a view of the ViVOpay
PISCES. This may require playing back a recording to see if PIN entry is visible. If the video
camera is moveable, the second person should move the video camera to determine if there is a
position where PIN entry can be observed.
Retesting Requirements
If PIN entry on the ViVOpay PISCES is observable in any of the above tests, you must reposition
the ViVOpay PISCES and completely retest all locations to verify that PIN entry is not visible.
Consider placing a display to block observation from that position.
Repositioning the ViVOpay PISCES to block observance of PIN entry at one location may expose
PIN entry to observation at another location. PCI requires that you reposition the ViVOpay
PISCES and retest until PIN entry is secure from observation.
Radio Frequency Interference
To perform contactless transactions, the ViVOpay PISCES uses a radio frequency antenna. The
range (reading distance) and performance of the reader can be affected by other radio frequency
emitters and proximity to metal.
For best performance, adhere to the following guidelines:
•
Do not position the ViVOpay PISCES closer than 1 foot (30 cm) to other
RF-emitting devices. Some environments may require greater distances.
•
Avoid placing the ViVOpay PISCES on or near large metal objects.
•
Do not position the ViVOpay PISCES near radio transmitters.
ViVOpay PISCES User Guide
Installing the ViVOpay PISCES
ESS
Installing the ViVOpay PISCES
This section describes how to install the ViVOpay PISCES. The basic steps are:
•
•
•
Connect to power and POS
Mount if required
Test the installation
Connecting the ViVOpay PISCES
Accessing the Connectors
The ViVOpay PISCES connectors are beneath a cover on the bottom of the reader.
To access the connectors
1. Turn over the ViVOpay PISCESso that the connector cover is visible.
2. Open to connector cover.
ViVOpay PISCES User Guide
Installing the ViVOpay PISCES
ESS
3. Insert the data cable into the HDMI connector directly
4. Close the cover
5. Turn the ViVOpay PISCES keypad side up.
6. Place the stylus in the holder at the side face of the ViVOpay POSCES.
7. Attach the data cable from the ViVOpay PISCES to the appropriate port on the POS.
ViVOpay PISCES User Guide
Installing the ViVOpay PISCES
ESS
8. Plug in the power supply. The ViVOpay PISCES the left LED illuminates.
The ViVOpay PISCES may take up to 30 seconds to finish booting.
The ViVOpay PISCES displays the opening set of screens before it displays the Welcome screen.
The opening screens include:
•
•
•
ViVOtech screen
Copyright screen
Firmware version screen
It should then display Welcome or Please present card or similar wording, depending upon the
POS application.
If the unit fails to power up, try reseating the power connector (or change to a different power outlet).
If the unit still fails to power up, try replacing the power supply. If the unit still fails to power up, and
the power supply is definitely good, contact your local support representative. For more
troubleshooting information, see “Troubleshooting” on page 9.
ViVOpay PISCES User Guide
Testing the Installation
Installing the ViVOpay PISCES
ESS
After you have completed the installation and have checked for PCI 4.1 conformance, run the
Onboard Diagnostic program as described in “Onboard Diagnostics” on page 10. Then check that
the ViVOpay PISCES and the POS are communicating correctly by performing a sample
transaction. The following test assumes that the host POS is already programmed to
communicate with the ViVOpay PISCES.
Transaction Test
The exact wording that appears on the ViVOpay PISCES depends on the POS application.
To test a transaction
1. Ring up a transaction on the POS. The ViVOpay PISCES may show Welcome or
similar wording.
2. Present a card/fob/phone in close proximity to the reader or swipe a magnetic stripe card.
3. A single beep and LED flash indicates that the card has been validated. The ViVOpay
PISCES may display Processing or similar wording while the transaction is
being processed.
4. If the POS software requires a PIN entry, you will see Please enter PIN. Use the keypad
to enter the PIN.
5. If the POS application requires a signature, you will see Please sign below. Use the
stylus to enter your signature on the touch screen.
6. A receipt is printed by the POS with the purchase amount. The ViVOpay PISCES may
show Thank You or similar wording for a successful transaction.
ViVOpay PISCES User Guide
Chapter 3
Troubleshooting and Maintenance
Troubleshooting
The ViVOpay PISCES readers are reliable and easy to troubleshoot. The components that may
require troubleshooting include the power supply, the reader and the data cable.
Symptom
Possible Cause
Probable Cause and Remedy
• Reader not powered on.
• Incorrect power supply used.
• Check cable connections.
• Verify that power is on and correct voltage and
current are present.
• Replace the power supply.
• Verify that power cable plug is fully inserted.
• Replace the power supply.
• Replace the reader.
LEDs do not light and beeper is
not audible when
card/fob/phone is presented.
• Card/fob/phone not properly
presented.
• Metal or RF interference.
• Wrong Firmware issue (contact your
local support representative).
• Reader not powered on or incorrect
voltage.
• Incorrect power supply used.
• Unsupported card/fob/phone used.
• Present card/fob/phone closer to the reader
and ensure it’s parallel to the reader touch
screen.
• Verify that the card/fob/phone is valid/current.
• Test with “ViVOcard Contactless Test Card”
part number 241-0015-03.
• Try a different card/fob/phone.
• Verify that the unit is not near any large metal
objects.
• Verify that correct firmware is loaded (local
support representative only).
• Verify that power is on and correct voltage and
current are present.
• Verify that power cable plug is fully inserted.
• Replace the reader.
Some cards/fobs/phones read,
but not all.
• Wrong firmware (contact your local
support representative).
• Possible bad card/fob/phone.
• Unsupported card used.
• Verify that correct firmware is loaded on
reader (local support representative only).
• Check to see if card/fob/phone is damaged.
• Try a different card/fob/phone.
On power-up, display sticks on
firmware version.
SAM card isn’t seated properly.
Remove power from unit, remove back cover and
reseat SAM card. If unsure, contact ViVOtech
Support for assistance.
General Issues
Reader does not appear to be
powered on—no LEDs lit, no
LCD display.
Reading Cards/Fobs/Phones
Troubleshooting and Maintenance
Symptom
Possible Cause
Probable Cause and Remedy
• Faulty or incorrect cable connections.
• Unsupported card used.
• Contactless application is not
installed on terminal (for serial
connections only).
• Magstripe card not swiped correctly.
• Magstripe card not level during card
swipe.
• The POS application is not using the
correct communications parameters.
• Check that the cable connection is secure and
in the correct port on the POS/ECR.
• Check that the POS/ECR has the correct
software application to accept data from the
contactless reader (may need assistance from
the POS vendor).
• Try a different card/fob/phone or magstripe
card if testing the magstripe reader.
• If testing with the magstripe card, try turning
the card around; make sure that the card is
level during the card swipe.
• Contact the payment processor for an
application upgrade.
• Check that the cable is correctly attached to
the back of the ViVOpay PISCES
• Check the POS application.
Communication to POS/ECR
No data is received, or data is
garbled.
Onboard Diagnostics
Onboard diagnostics (OBD) tests the following components of the ViVOpay
PISCES. Is there a smart card test?
Test
Possible Results
LCD Test
Pass/Fail
TouchScreen Test
Pass/Fail
Keypad Test
Pass/Fail 1234567890* #
LEDs Test
Pass/Fail virtual leds MSR ICC Keypad backlight
Tone Test
Pass/Fail
Magstripe Test
Pass Tracks 1 or 2 or 3/Fail
RFID Test
Pass Type A or B/Fail
ICC Test
Pass T = 0 or T = 1/Fail
Ethernet Test
Pass/Fail
SAMs Test
Pass SAM1 SAM2 SAM3/Fail
Accessing the OBD Tests
To enter the onboard diagnostics
1. Power off the ViVOpay PISCES by removing the power supply from the power receptacle.
2. Plug the power supply back into the power receptacle.
10
Troubleshooting and Maintenance
3. After applying power. Please press key "1" and then press press key "#" within 3 sec after
LCD display "Welcome". If you input correctly, The ViVOpay AR Diagnostics will appears on
the screen and prompt alarm will sound.
The menu first page as below:
ViVOpay AR Diagnostics
Test Results Summary
Test Al l
LCD
Touch Screen
Keypad
LEDs
Tone
Magstripe
RFID and Antenna
ICC
O: Next Page
X: Exit
The menu second page as below:
ViVOpay AR Diagnostics
0 Ethernet
1 SAMs
<: Prev Page X: Exit
11
Troubleshooting and Maintenance
Maintenance
The ViVOpay PISCES contains no user-serviceable parts within its enclosure. Do not open the
ViVOpay PISCES enclosure.
WARNING: Attempting to open the ViVOpay PISCES enclosure will trigger PCI
security measures and it will stop functioning even after reassembly!
You can replace the stylus without violating PCI security measures. You can also upgrade the
ViVOpay PISCES’s firmware if required.
Replacing the Stylus
It is important that only the stylus be used for writing on the touch screen. If the stylus is lost or the
lanyard broken, you can obtain a replacement from your ViVOpay PISCES distributor
To replace the stylus
1. Turn the ViVOpay PISCES upside down and unscrew the screw for the tether wire of
stylus.
2. Remove the old stylus with the new one. Then fasten the screw.
3. Turn the ViVOpay PISCES back and place the new stylus in its holder.
12
Troubleshooting and Maintenance
Upgrading the Firmware
You can upgrade the firmware of the ViVOpay PISCES if required for your application. You will
need the following from your ViVOpay PISCES distributor:
•
New ViVOpay firmware
ViVOpay download utility
USB data cable
You also need a PC with a USB port. The PC should have the required USB driver HID.DLL file. If
not, it is available for download from Microsoft’s website.
To upgrade the firmware
Copy the firmware image and ViVOpay download utility to the PC you are using for
the upgrade.
Connect the USB data cable to the ViVOpay PISCES and PC (see “Connecting
Power, Stylus, and Data Cables” on page 6).
Double click the ViVOpay download utility icon or .exe to start the utility.
Power on the ViVOpay PISCES. The bootloader version will appear.
According to the image type to click the corresponding bottom.
5.1
Click Download Bootloader to download bootloader.
5.2
Click Download Image to download firmware.
When prompted, locate and select the bootloader or firmware image to download
and click OK.
When the download is complete, disconnect the ViVOpay PISCES from the PC and
power. The new bootloader or firmware will be active next time you apply power to
the ViVOpay PISCES.
Reconnect power.
13
Appendix A
Specifications
ViVOpay PISCES Specifications
For detailed specifications, see the ViVOpay PISCES Technical Specifications.
RF Interface
Frequency
13.56 MHz
Standard
ISO 14443 Type A&B, Mifare, ISO 18092
Reading distance
MAX 4cm
Physical
Length
175 mm
Width
95 mm maximum
Depth
58 mm maximum
Weight
0.4Kg
Environmental
Operating Temp.
0 to 55° C (32 to 131° F)
Storage Temp.
-25 to 65° C (-13 to 149° F)
Relative Humidity
10 to 95% non-condensing
Operating Environment
Indoor only
Power
Voltage
5 Vdc regulated, +/- 10%
Consumption
6 W maximum
Power supply
The PISCES shall be powered by an external
power source (P/N AC005R)
(power-pack AC 85-265)
ViVOpay 8850 User Guide
14
Glossary
Electronic Cash Register (ECR)
The combination of a traditional cash register and a POS terminal, often PC-based.
ExpressPay from American Express
American Express contactless payment product that utilizes contactless technology.
Firmware
Software that is embedded in a hardware device that allows reading and executing the
software, but does not allow modification, e.g., writing or deleting data by an end user.
Example: Firmware is a computer program in a read-only memory (ROM) integrated circuit
chip. A hardware configuration is usually used to represent the software.
Example: Firmware is a program embedded in an erasable programmable read-only memory
(EPROM) chip, which program may be modified by special external hardware, but not by an
application program.
Fob
A key chain device or other non-standard credit card sized form factor that has an embedded
radio frequency (RF) chip.
MasterCard PayPass
MasterCard's contactless payment product that utilizes contactless technology.
NFC
Near Field Communications.
NFC Phone
Near Field Communications (NFC) phone. A technology that enables communication between a
secure element in a mobile device and a contactless reader to make credit/debit payments.
Also see UICC.
PCI 4.1
The Payment Card Industry Security Standards Council (PCI SSC) mission is to enhance
payment account data security. PCI 4.1 is a set of standards created by PCI SSC to increase
the security of card data.
Point of Sale (POS)
Refers to terminals used in retail stores with a magnetic stripe reader, keyboard, display and
autodialer modem or IP connection, connected to the telephone/internet network and used for
on-line credit/debit authorization. Can also be connected to a host computer, which handles all
transaction processing including item price look-up, data collection, and credit/debit
authorization.
Proximity Payments
Payment method utilizing contactless technology such as RF, Infrared (IrDA) or Near Field
Communications (NFC).
Radio Frequency (RF)
Any frequency that corresponds to radio signals, including those used by cellular telephones
and wireless networks.
RF Reader
The Point of Sale device that receives the RF transmission from a card, fob or NFC phone.
Visa Contactless
Visa's contactless payment product that utilizes contactless technology.
Symbol Explanations:
EMV Contactless Symbol
ViVOpay PISCES User Guide
15

---

Source Exif Data:

EXIF Metadata provided by EXIF.tools