Smart
Smart Dual
Card Printer
User Manual
XG
Copyright Notice
Users must respect the copyright laws applicable in their country. This manual must not be
photocopied, translated, reproduced or transmitted in whole or in part for any reason and
by the means that might be, albeit electronic or mechanical, without the express, written
authorization of the company I&A System card printer.
All information contained herein may be subject to modification without prior notice.
I&A System card printer accepts no liability for any possible errors herein, nor for any
accidental damage or damage caused through the dissemination or the use of this manual.
Trademarks
Smart is a trademark and I&A System is a registered trademark of I&A System card printer.
Windows is registered trademarks of Microsoft Corp. All other trademarks or registered
trademarks are marks of their respective holders. Smart Design is a trademark of I&A
System.
Return Materials Authorization
In order to make a warranty claim you must contact an I&A System Reseller. You will be
responsible for packaging the printer for shipment and the costs of shipping and insurance
of the printer from the point of use of the printer to the I&A System Reseller. The I&A
System Reseller will bear the costs of shipping and insuring the printer from the repair
location to the address from which the printer was shipped.
Before returning any equipment for in-warranty or out-of warranty repair, contact an I&A
System Reseller or an I&A System Service Center for a Return Materials Authorization
(RMA) number. Repack the equipment in the original packing material and mark the RMA
number clearly on the outside of the box. For more information about RMA or I&A System
warranty statements, refer to the Warranty booklet on the quick install guide.
YG
TABLE OF CONTENTS
1. Introduction
1.1
Printer Outside Features
1.2
Printer Inside Features
1.3
Ribbon Cartridge Features
------------------------------------------------------------------------
--------------------------------------------------------------------------
----------------------------------------------------------------------
1.4 LCD Panel Display and Button Operation
-------------------------------------------------
----------------------------------------------------------------------------------
10
--------------------------------------------------------------------------------------
12
2. Installing the Printer
2.1 Loading a Ribbon
2.2 Loading Cards
2.3
Installation the Printer Driver
------------------------------------------------------------------
14
2.4
Test Printing ------------------------------------------------------------------------------------------
17
2.5 Changing a Ribbon and Cleaning Roller ---------------------------------------------------
18
3. Checking and changing the Printer Properties
3.1 Checking the Printer Properties
---------------------------------------------------------------
19
3.2
Changing the Printing Setting --------------------------------------------------------------------
20
3.3
Changing the Printer Properties -----------------------------------------------------------------
21
4. Troubleshooting
4.1
Card Transfer
4.2
Printing Quality
4.3
Magnetic Stripe Encoder
4.4
General Operation
----------------------------------------------------------------------------------------
23
--------------------------------------------------------------------------------------
24
5. Printer Specification
------------------------------------------------------------------------
25
---------------------------------------------------------------------------------
27
-----------------------------------------------------------------------------
27
ZG
TABLE OF FIGURES
Printer Front/Side Features -----------------------------------------------------------
-----------------------------------------------------------------
------------------------------------------------------------------------------
------------------------------------------------------------------------
Printer Rear Feature
Printer Inside
Ribbon Cartridge
Open Top Cover ---------------------------------------------------------------------------
10
Take out the cartridge
-----------------------------------------------------------------
10
Preparation the ribbon
----------------------------------------------------------------
10
------------------------------------------------------------------------
11
Install the ribbon
Install the cleaning roller
------------------------------------------------------------
11
Peel the protective rapper
---------------------------------------------------------
11
Install the ribbon cartridge
-------------------------------------------------------
12
----------------------------------------------------------------------
12
-------------------------------------------------------------
12
Holding the Cards ----------------------------------------------------------------------
13
--------------------------------------------------
13
--------------------------------------------------------------
13
--------------------------
13
Connect the Power Cord----------------------------------------------------------------
14
-------------------------------------------------------------------------------
14
Driver Install Guide --------------------------------------------------------------------
14
Driver Installation
----------------------------------------------------------------------
15
Printer Turn ON
-------------------------------------------------------------------------
15
No, not this time
------------------------------------------------------------------------
15
Install the software automatically ----------------------------------------------
15
---------------------------------------------------------------------
16
---------------------------------------------------------------------------------------
16
-----------------------------------------------------------
16
Printer Properties ----------------------------------------------------------------------
17
Printer Test Page -----------------------------------------------------------------------
17
--------------------------------------------------------------------------
17
Close Top Cover
Adjust Card Thickness
Push the stack back and forth
Restore the card stack
Placing the cards and close the hopper cover
CD Loading
Continue Anyway
Finish
I&A SMART Card Printer
[G
Test Print O.K
Ribbon Separation ----------------------------------------------------------------------
18
Checking the Printer Properties
------------------------------------------------
19
-------------------------------------------------------------------------
20
--------------------------------------------------------------------------------------
20
----------------------------------------------------------------
20
--------------------------------------------------------------------------------
21
-------------------------------------------------------------------------
21
------------------------------------------------------------------------------------------
22
---------------------------------------------------------------------------------
22
----------------------------------------------------------------------------------------
22
Printing Setting
Layout
Paper/Ribbon/Quality
Side/Media
Sharing Printer
Port
Advanced
Color
Print Quality Trouble Example 1
------------------------------------------------
24
Print Quality Trouble Example 2
------------------------------------------------
24
Print Quality Trouble Example 3
------------------------------------------------
24
Print Quality Trouble Example 4
------------------------------------------------
24
Print Quality Trouble Example 5
------------------------------------------------
25
\G
1. Introduction
Thank you for choosing the I&A System Smart Card Printer. This manual helps you effectively
and professionally for the start-up and operation of your new Card Printer.
1.1 Printer Outside Features
This Smart Card Printer takes a power via the adaptor provided with the printer. Using
USB port, it communicates with user’s PC. For the user’s convenience, the printer
process status can be seen through LCD and most of the operations can be controlled
by two LED buttons.
The following shows the external functional features found on your Smart Printer.
Top Cover Open Button
External Contactless IC Encoding
Position
Hopper (Input Hopper)
LED buttons
LCD (Show the process status)
Magnetic/Contact IC/Contactless IC
Encoder are installed inside
HG
External Contact IC Encoder
(SIM Type)
Stacker (Output Hopper)
Power Switch
Power Connector
USB Port
LG
Rear Card Outlet
(If necessary)
Printer Front/Side Features
J K
Printer Rear Feature
]G
1.2 Printer Inside Features
Smart Printer adopts a semi-permanent Ribbon cartridge.
The following shows the internal functional features found on your Smart Printer.
Thermal Printer Head
Ribbon Cartridge
Card Thickness Control lever
Hopper
Stacker(Output Hopper)
External Contactless IC Antenna
Manual Card Output Wheel
Printer Inside Features
1.2.1 Thermal Printer Head
This enables the cards to be printed.
(Caution!
Do not contact the surface of the printer head with fingers or a sharp metal object to
avoid degrading print quality or damaging printer head permanently.)
1.2.2 Hopper(Card Input Hopper)
Load the cards for printing.
1.2.3 Stacker(Card Output Hopper)
Collect the printed and/or encoded cards.
1.2.4 Card Thickness Control lever
Adjust the cards thickness.
1.2.5 Manual Card Output Wheel
When a card is jammed, the card can be out using this wheel by manually.
(Information!
Most of the card jam error can be solved by controlling the front LED buttons. So use
this wheel when the problem is not solved by using the front LED buttons.)
^G
1.3
Ribbon Cartridge Features
Ribbon Cartridge
Ribbon
Disposable Cleaning Roller
Ribbon Cartridge
1.3.1 Ribbon Cartridge
Install a Ribbon and a disposable cleaning roller provided with the Ribbon.
(Important!
This semi-permanent ribbon cartridge is a component of the printer. Printer does not
operate if it is broken or damaged. In this case, please contact printer reseller.)
1.3.2 Ribbon
Ribbon for printing.
1.3.3 Disposable Cleaning Roller
It removes dust in the surface of card to improve print quality before the card is printed.
It should be changed together with the Ribbon.
(Caution! This disposable cleaning roller is provided with the Ribbon. If this is not changed,
print quality mighty be degraded.)
_G
1.4 LCD Panel Display and Button Operation
Smart Printer shows the real-time process status to user. Please refer to the below
LCD panel display and button operation.
LED Buttons
Left Press
Right Press
No
LCD Message
SMART
System Ready
Ver X.XX…
Initialize…
Initializing
SMART
Printing!
Printing
SMART
Mag R/W
Magnetic
Read/Write
SMART
Out of Ribbon
No Ribbon
SMART
Out of Card
No Card
SMART
Top Cover Open
Move
transportation
roller to left
Move
transportation
roller to right
Top Cover open
Ribbon Not Found
Replay
Cancel &
initialize
Fail to find a proper
color
Card In Error
Replay
Cancel &
initialize
Fail to the card
loading
10
Reposition Error
Replay
Cancel &
initialize
Fail to the card
transporting
11
Head U/D Error
Replay
Cancel &
initialize
Fail to the print
head up and down
12
Card Out Error
Replay
Cancel &
initialize
Fail to the card out
13
Mag R/W Error
Replay
Cancel &
initialize
Fail to the magnetic
Read/Write
LED ON /
Printer Setting
Information
(only for A/S)
Software
Power ON/OFF
Printer Status
System Stand By
LED BLINKING
ƒ SMART System Ready : System is ready to print. Press left button to see the printer setting
information and press right button or Power ON/OFF by software.
ƒ Ver X.XX… Initialize… : Under checking the printer’s version and initializing.
ƒ SMART Printing! : Printing.
ƒ SMART Mag R/W : Reading or writing the data on Magnetic Stripe.
ƒ SMART Out of Ribbon : No Ribbon in the printer or Ribbon is used all. Check the Ribbon!
ƒ SMART Out of Card : No Cards in the hopper. Check the Cards on the hopper!
ƒ SMART Case Open : Top Cover is open. Please close the Top Cover.
ƒ Ribbon Not found : Ribbon search is failed. Press left button to replay or press right button to cancel.
ƒ Card In Error : Card insertion is failed. Check the card on the hopper! Press left button to replay
or press right button to cancel.
ƒ Reposition Error : Card is not moved to the proper position. Press left button to replay or press right
button to cancel.
ƒ Head U/D Error : Printer head is not moved to the proper position. Press left button to replay or
press right button to cancel.
ƒ Card Out Error : Card is not outputted. Press left button to replay or press right button to cancel.
ƒ Mag R/W Error : Reading or writing the data is failed. Press left button to replay or press right
button to cancel.
`G
2. Installing the Printer
2.1 Loading a Ribbon
Before print, prepare the related items such as a card, a ribbon and a cleaning roller.
In this section, we invite you to know the proper method to install the Ribbon and
cleaning roller to the printer.
2.1.1
Make the printer power OFF.
2.1.2 Open the printer top cover
by pressing the top cover
open button.
Open Top Cover
2.1.3 Take out the ribbon cartridge.
Take out the cartridge
2.1.4. Prepare the ribbon before
inserting it into the cartridge.
Refer to the illustration on
the inside of the cartridge.
Prepare the ribbon
XWG
2.1.5. Insert the supply side of the ribbon to no.1 hole and press the opposite
(no.2) until it clicks. Insert the take-up side of the ribbon same method
to no.3 and no.4. And fasten the ribbon.
(Caution! If the ribbon is not fastened, a rolling up error might happen.)
Install the ribbon
2.1.6. Install the disposable cleaning
roller to the ribbon cartridge.
Install the cleaning roller
2.1.7. Peel the protective wrapper from the cleaning roller.
To avoid contamination, always hold the cleaning roller. Be careful of touching, dust and
contamination because it is adhesive.
(Caution! Do not use without peeling off
the protective wrapper.
The cleaning roller do not perform its
function.)
ᶤ
Peel the protective wrapper
XXG
2.1.8. Install the ribbon cartridge to
the printer after install
the ribbon and cleaning roller
to the cartridge.
Install the ribbon cartridge
2.1.9. Close the top cover until it
clicks.
If it is not closed, check
the installation state of
the ribbon cartridge.
Close Top Cover
2.2. Loading Cards
This section shows how to load plastic cards into the Smart Printer.
2.2.1. If the card hopper cover is closed, open it.
2.2.2. Adjust the card thickness with
control lever.
(Caution! If the adjustment is not correct, it will
make some errors. Use the type of cards
appearing in the specification in this manual.
Always keep cards surface clean.)
Adjust the card thickness
XYG
2.2.3. Hold the cards by sides like
picture
(Caution! Do not bend the cards and
do not touch the surface of the cards)
Holding the cards
2.2.4. Push the stack back and forth to an angle of about 45° vertically.
(Note : Static charge makes cards stuck with significant adhesive force. These cards
must be physically separated from each other before inserted into the feeder.
If not separated, feeding or printing problems may occur.)
Push the stack back and forth
2.2.5. Restore the card stack to its
original condition.
Restore the card stack
2.2.6. Place the card to the input hopper and close the hopper cover.
Placing the cards and close the hopper cover
XZG
2.3. Installing the Printer Driver
2.3.1. Check the printer’s power OFF.
2.3.2. Connect the power cord and USB
cable to the printer.
Connect the power cord
2.3.3. Insert CD provided with the printer.
CD loading
2.3.4. Click “Driver Install Guide”
Driver Install Guide
X[G
2.3.5. Check and follow
the driver installation guide.
Driver Installation
2.3.6. Turn On the printer.
Printer Turn ON
2.3.7. Select “No, not this time”
and click “ Next”.
No, not this time
2.3.8. Select “Install the software
automatically” and click “Next”.
Install the software automatically
X\G
2.3.9. Click “Continue Anyway” in
Hardware Installation.
Continue Anyway
2.3.10. Click “Finish” in Completing
the Found New Hardware Wizard.
Finish
2.3.11. Check “I&A SMART Card
Printerºis generated in Printers
and Faxes.
I&A SMART Card Printer
X]G
2.4. Test Printing
In this step, you can check whether the printer driver installation has been finished
successfully.
2.4.1. In “Printer and Fax” window,
click right button on ‘I&A SMART
Card Printer’ icon, then select
“Properties”.
Printer Properties
2.4.2. After selecting “General” tab
in “I&A SMART Card Printer
properties” window, click “Print
Test Page” button.
Print Test Page
2.4.3. Printer will start printing, and
on the screen it will be asked
whether printing was successful.
(If the printing is abnormal or printer error occurs,
you may execute test printing again after resolving
the problem with the assistance of “Trouble
Shooting” section.)
Test Print O.K
X^G
2.5. Changing a Ribbon and a Cleaning Roller
When you change ribbon, you have to change cleaning roller, too.
(Caution! Without changing disposable cleaning roller, the printing quality is not
guaranteed.)
2.5.1. Turn off the printer power.
2.5.2. Open the top cover, and then take
out the ribbon cartridge.
2.5.3. Separate bar-1 from the cartridge,
then bar-2. Lift up the ribbon bars in
order of 3 and 4.
Ribbon Separation
2.5.4. Remove the used ribbon. Set up the new ribbon and cleaning roller
together, with the reference of 2.1 “Ribbon Setting”.
X_G
3. Checking and changing the Printer
Properties
3.1. Checking the Printer Properties
To check the Smart Printer Properties, go to “Control Panel”, click right button on “I&A
SMART Card Printer” in Printers and Faxes. Then select “Properties”.
Checking the Printer PropertiesG
When you select “Properties” in “I&A SMART Card Printer”, a window, you can check
and change the properties, will be created as .
X`G
3.2. Changing the Printer Setting
In “General” tab of , you can see the printer model and specification.
3.2.1 Basic Printing Setting
There are 3 tabs of Layout,
Paper/Ribbon/Quality, and
Side/Media.
(You can set the options for
printing in the window of
.)
Printing SettingG
.2.1.1 Layout tab
- You can select either horizontal or vertical
printing direction. To apply your selection,
click “OK” button.
(Caution! Default value is recommended in
advanced option. If you want to change
the value, please contact I&A System
Reseller.)
LayoutG
3.2.1.2 Paper / Ribbon / Quality tab
You can set the type of paper, ribbon,
and quality as .
- Paper Tray
Select tray and card type option.
SMART has only one hopper and supports
only CR-80 type card. You need not to change
default value in this option.
- Ribbon
You can see the type of ribbon. SMART
identifies ribbon type automatically with RF Tag.
You do not need select the ribbon type.
Paper/Ribbon/Quality
- Resin
YWG
You can set the method to extract resin black when the printing is executed by other design
programs. If you use Smart Design, you don’t need to select this option. It will be set
automatically.
- Quality
Print quality setting - There are 2 modes, Standard and High.
High: Printing speed will be slow down.
Color: You can select color or black & white print.
Caution! “Color” option is available only with color ribbon.
Dither: There are 3 possible selections, Threshold, Random, and Diffusion Dither.
(Select “Diffusion Dither” for high quality.)
3.2.1.3 Side/Media tab
You can set the printing side and
printing mask.
Print Side
You can select one side printing or both
Sides printing.
Front / Back
The previously defined mask (standard,
smartcard, magnetic, etc) can be
applied to front or back side.
Side/Media
3.3. Changing the Printer Properties
3.3.1 Share tab
“Share” option allows printer to share
through network as .
Default value is “Not Share”.
Ἤ
Sharing Printer
YXG
3.3.2 Port tab
Port tab shows the port connecting
with SMART. SMART has connection
with USB Virtual printer port as
because SMART uses
USB to connect with PC.
(Caution! This port is selected
automatically. It is recommended to
maintain default value.)
Ports
3.3.3 Advanced tab
It is for “Time option” setting, “Priority
order”, “Spool”, and etc are available in
“Advanced” tab. “Advanced” setting
follows MS Windows standard.
If you want to change the setting,
refer to the Window manual.
(It is recommended to maintain
default value.)
Advanced
3.3.4 Color Management tab
In “Color management” tab, you can
select color management profile fit to
the printer.
SMART uses color profile to express
optimal color. The default profile is
‘inasmart’.
(It is recommended to maintain
default value.)
Color
YYG
4. Troubleshooting
In this section, you would get useful solutions about some possible problems
while using printer.
4.1. Card Transfer
4.1.1. Card can’t enter into the printer from card hopper.
If the card can’t get into the printer at all or insert problems occur frequently, check the
followings.
Non-standard cards or bad cards:
Change the cards.
When the card thickness control lever is set not for current card but for other card in
different size:
Move the lever to fit the current card.
Bad card array:
Array the cards again and put them in the hopper as section 2.4 in this manual.
Wet cards or cards having static:
Remove the moisture or static.
4.1.2. Transfer error occurs when ribbon is stuck to the transfer roller or to
the printing roller.
Open the top cover and remove the card with front switch or manual transfer wheel. Check
the followings, if transfer related problems occur frequently.
Non-standard cards or bad cards:
Change the cards.
When the transfer roller or printing roller is stained with dirt
Remove the dirt with the cleaning kit.
Wrong printing position setting:
Please contact I&A System Reseller.
When operating temperature and humidity is out of the acceptable operating limit of the
printer:
Adjust the condition to the printer.
4.1.3. An error occurs during card transfer.
Open the top cover and remove the card with front switch or manual transfer wheel. Check
the followings, if transfer related problems occur frequently. First of all, check the error
message on the LCD screen.
Non-standard cards or bad cards:
Change the cards.
Inappropriate printer setting:
Please contact I&A System Reseller.
When the printer roller is stained with dirt:
Remove the dirt with the cleaning kit.
When the surface of the card is stained with dirt:
After checking the card, change it to another card.
YZG
4.2. Print quality
4.2.1. Small dots appear: Some parts of the card are
not printed or are printed with wrong colors.
When the surface of the card is stained with dirt:
After checking the card, change it to another card.
When the cleaning roller is stained with dirt:
Check the cleaning roller. If there is much dust, change the roller to
the new one.
Much dust in the printer:
Print Quality Trouble
Clean the inside of the printer with the cleaning kit.
Example1
4.2.2. Horizontal lines appear, because the areas are
not printed.
Inaccurate ribbon cartridge installation:
Check the ribbon cartridge installation whether the ribbon has
wrinkles.
When the printer head is stained with dirt:
Clean the printer head.
Print Quality Trouble
Damaged printer head surface:
Example2
Please contact I&A System Reseller for replacement.
4.2.3. The print is not clear, or is uneven.
Uneven or bad card surface:
Change the card.
Too high or low value of the depth of color:
Please contact I&A System Reseller. The default value of the depth
of color for your printer needs to be changed.
When the printer head is stained with dirt:
Print Quality Trouble
Clean the printer head.
Example3
4.2.4. The color of the printed image strays from its
place slightly.
Non-standard card:
Change to the standard card.
Uneven or bad card surface:
Change the card.
When the transfer roller or printing roller is stained with dirt:
Print Quality Trouble
Remove the dirt with the cleaning kit.
Example4
Worn-out printer:
Please contact I&A System Reseller.
Y[G
4.2.5. The printer prints unplanned color at the edge,
or the printed color is quite different from the
original image.
Non-standard card:
Change to the standard card.
Uneven or bad card surface:
Change the card.
When the transfer roller or printing roller is stained
with dirt:
Remove the dirt with the cleaning kit.
Worn-out printer:
Please contact I&A System Reseller.
Print Quality Trouble
Example5
4.3. Magnetic Stripe Encoder
4.3.1. An error occurs in magnetic stripe encoder.
To replay, press the left LED button.
When the magnetic head is stained with dirt:
Remove the dirt with the cleaning kit.
When magnetic data is not transferred or transfer error occurs:
Check the setting of the program and the driver whether the data fits the standard of the track.
When inserted card is not magnetic card, or inserting direction is wrong:
Change the card or the direction.
Bad magnetic stripes on the card:
Change the card.
4.4. General Operation
4.4.1. Ribbon is torn while printing.
Open the top cover and take out the cartridge. After putting the broken pieces on together,
install the cartridge again. Check the followings if this kind of problem occurs frequently.
Non-standard card, Uneven card surface, etc:
Change the card.
Too high value of the depth of color:
Please contact I&A System Reseller. The default value of the depth of color for your printer
needs to be changed.
4.4.2. LCD screen displays the error message “Ribbon Not Found”.
To replay, press the left LED button. Check the followings if this kind of problem occurs
frequently.
Non-standard ribbon:
Change to the standard ribbon.
Ribbon is consumed.
Printing is not possible if ribbon is used up. Change the ribbon.
Broken ribbon:
Refer to 4.4.1.
4.4.3. Printer does not operate though the printing data has been transferred.
Check the followings.
Printer power off:
Check the power. Turn on the printer power.
Check the printer adaptor whether it is connected with a socket and the printer.
Y\G
Bad power adaptor:
Please contact I&A System Reseller for replacement of the adaptor.
When the value of the printer driver is not “Online” but “Offline”:
Change the setting to “Online”.
When the USB cable for printer transfer is off or the connection is bad:
Check the connection of the cable between PC and the printer.
Make the USB cable connection again.
Bad USB cable for printer transfer:
Change the USB cable.
If the selected printer is different model rather than SMART:
Select SMART to print.
Wrong port setting of the printer driver:
Check the port setting of the printer driver whether it is USB port or not.
No ribbon in the printer or printer in error mode:
Install ribbon in the printer or resolve the error.
Too long power or transfer cable (more than 1.5M):
Use the cable provided with the printer.
When USB transfer port of PC is down:
Restart your PC.
Y]G
5. Printer Specification
Product Specification
Smart
Printing Method
Smart Dual
PVC, Polyester Cards with polished PVC finish
Card Type
Dye-Sublimation / Resin Thermal Transfers / Edge - to - Edge
ISO CR-80 (54mm x 86mm / 2.12" x 3.38")
Card Format
0.38mm (15mil) ~ 1.0mm (40mil)
Card Thickness
300 dpi
Resolution
32MB
Memory
Color (YMCKO) : max 144 cards / hour
Printing Speed
Color (YMCKOK) : max 120 cards / hour
Black Overlay (KO) : max 360 cards / hour
Mono (Black) : max 720 cards / hour
Color (YMCKO) : 250 cards / roll
Ribbon Capacity
Color (YMCKOK) : 200 cards / roll
Black Overlay (KO) : 600 cards / roll
Mono : 1,200 cards / roll (Black, Gold, Silver)
Hopper : 90 cards, Stacker : 40 cards
Hopper & Stacker
USB
Interface
2 Lines LCD & LED
Display
Free Voltage (110/240V AC), 50 ~ 60 Hz
Power
Dimension
Operating Environment
Weight
170mm(W) x 195mm(H) x 420mm(D)
170mm(W) x 195mm(H) x 510mm(D)
Temperature : - 20 ~ 55, Humidity : 20 ~ 95%
4.5 Kg
5.5 Kg
Agency Listing
MIC, CE, UL, FCC
Printer Driver
Windows 2000 / 2003 / XP
Option
Magnetic Stripe
Encoding Module
ISO7811 (Track ዜ,ዝ,ዞ Read / Write), JISዝ, HiCo / LoCo
ISO7816 (ID-1)
IC (Contact) Encoding
SIM Type - ISO7816 (ID-000)
Two Contactless
Encoding
ISO14443 (Type A / B), ISO15693, MIFARE
(Internal & External)
Rotator
Option
Default
* Specifications are subject to change with or without notice.G
Y^G
FCC warning
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio, TV technical for help.
Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly
approved by the grantee or manufacturer could void the users’ authority to
operate such equipment.
CE warning
! Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
EN Test Regulation Version.
1) EN 300 330-1 V1.5.1:2006.04
2) EN 301 489-1 V1.6.1:2005.09
3) EN 301 489-3 V1.4.1:2002.08
Y_G
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.4
Linearized : No
XMP Toolkit : 3.1-701
Producer : Acrobat Distiller 7.0.5 (Windows)
Create Date : 2007:12:18 09:11:28+09:00
Modify Date : 2007:12:18 09:11:28+09:00
Metadata Date : 2007:12:18 09:11:27+09:00
Creator Tool : PScript5.dll Version 5.2
Document ID : uuid:389E9565FCACDC119DF9BAFF80E159BF
Instance ID : uuid:7340b95c-d82b-4a14-ac46-a0319c7f659b
Derived From Instance ID : uuid:c870959e-92c6-4a33-8637-897837172d02
Derived From Document ID : uuid:83a2038c-e57c-46b0-a37a-288ab6b2f380
Format : application/postscript
Title : Microsoft Word - User Manual.doc
Creator :
Page Count : 28
Author :
