IDS GeoRadar s r l HR2000NA Ground Penetrating Radar User Manual manuale d uso

Download:
Mirror Download [FCC.gov]
Document ID	1624103
Application ID	VImcLsl5OZ3xBCGOrtgs0w==
Document Description	User & technical manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	96.4kB (1205051 bits)
Date Submitted	2012-01-19 00:00:00
Date Available	2012-02-17 00:00:00
Creation Date	2011-12-13 17:33:09
Producing Software	Microsoft® Word 2010
Document Lastmod	2011-12-13 17:33:09
Document Title	manuale d'uso
Document Creator	Microsoft® Word 2010
Document Author:	Valter Baroncini

IDS Ingegneria Dei Sistemi S.p.A.
Hi-Pave – User Manual
N doc:MN/2011/004 - Rev. 1.1
Config.: Hi-Pave-PRCS-OUT-MN
- PRO/010/M1 Rev 4 -
INGEGNERIA DEI SISTEMI S.p.A.
Rev. 1.1
N°doc:MN/2011/004
Config.: Hi-Pave-PRCS-OUT-MN
Hi-Pave System Assembly
User Manual
Hi-Pave –
User Manual
Pisa, December 2011
1 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
KEYWORDS: HI-PAVE, ENCODER, ANTENNA, FRAME
SUMMARY: This manual explains the procedure of assembling the Hi-Pave GPR system in all its
parts.
Document Evolution
Revision
Date
Reason of change
Rev. 1.0
18/02/2011
First Edition
Rev. 1.1
2/12/2011
FCC/IC Information added
Versions covered by this document
Contacts
IDS Ingegneria dei Sistemi S.p.A. – GeoRadar Division
Via Enrica Calabresi, 20
56121 Montacchiello (PISA) - ITALIA
Tel: +39.050.3124350
Fax: +39.050.3124205
inforis@ids-spa.it
Customer Care department:
customercare.gpr@ids-spa.it
Tel.: +39.050.3124 355/356
Sales & Marketing department:
sales.gpr@ids-spa.it
Tel.: +39.050.3124352
2 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
Disclaimer
IDS WILL NOT BE HELD RESPONSIBLE FOR THE CONSEQUENCES OF AN
IMPROPER USE OF THE EQUIPMENT AND/OR THE SOFTWARE. THIS
SOFTWARE MAY INCLUDE AUTOMATED DATA PROCESSING AND
ANALYSIS TOOLS. WHILE EVERY EFFORT IS MADE TO ENSURE THE
ACCURACY OF THE INFORMATION PROVIDED BY THOSE TOOLS, THEY
MUST NOT BE INTENDED AS A SUBSTITUTE FOR INTELLIGENT ANALYSIS;
RATHER, THEY HAVE TO BE INTENDED AS AN ADVISOR AND THE USER
MUST NOT COMPLETELY RELY ON THE RESULTS PROVIDED BY THEM TO
GIVE THE COMPLETE ANSWER.
IDS INGEGNERIA DEI SISTEMI SPA ASSUMES NO LIABILITY FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR INJURIES CAUSED BY SUCH RELIANCE ON THE ACCURACY,
RELIABILITY, OR TIMELESS OF THE INFORMATION PROVIDED BY THOSE
TOOLS.
ANY PERSON OR ENTITY WHO RELIES ON INFORMATION OBTAINED FROM
THE AUTOMATED DATA PROCESSING/ANALYSIS TOOLS ONLY, DOES SO AT
HIS OR HER OWN RISK
3 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
SAFETY INFORMATION
The equipment conforms to the following requirements set by EC
regulations, including subsequent modifications, and to the legislation set
by the member states that implement these regulations:
1999/05/EEC Radio Directive
Warning: this equipment is destined for use in industrial environments
(Class A apparatus). In residential, commercial and light industry
environments, this apparatus may generate radio interference: in this case,
the user may be required to operate while taking appropriate
countermeasures.
The apparatus is sensitive to the presence of external electromagnetic fields,
which may reduce its performance.
4 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
IMPORTANT NOTE FOR THE US CUSTOMERS
FCC ID: UFW-HR2000NA
This device complies with part 15 of the FCC Rules:
Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, Including interference that may cause undesired
operation
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Operation of this device is restricted to law enforcement, fire and rescue officials, scientific research
institutes, commercial mining companies, and construction companies. Operation by any other party is a
violation of 47 U.S.C. § 301 and could subject the operator to serious legal penalties.
Coordination Requirements.
(a) UWB imaging systems require coordination through the FCC before the equipment may be used. The
operator shall comply with any constraints on equipment usage resulting from this coordination.
(b) The users of UWB imaging devices shall supply detailed operational areas to the FCC Office of
Engineering and Technology who shall coordinate this information with the Federal Government through
the National Telecommunications and Information Administration. The information provided by the UWB
operator shall include the name, address and other pertinent contact information of the user, the desired
geographical area of operation, and the FCC ID number and other nomenclature of the UWB device. This
material shall be submitted to the following address:
Frequency Coordination Branch., OET
Federal Communications Commission
445 12th Street, SW
Washington, D.C. 20554
ATTN: UWB Coordination
(d) Users of authorized, coordinated UWB systems may transfer them to other qualified users and to
different locations upon coordination of change of ownership or location to the FCC and coordination with
existing authorized operations.
(e) The NTIA/FCC coordination report shall include any needed constraints that apply to day-to-day
operations. Such constraints could specify prohibited areas of operations or areas located near authorized
radio stations for which additional coordination is required before operation of the UWB equipment. If
additional local coordination is required, a local coordination contact will be provided.
(f) The coordination of routine UWB operations shall not take longer than 15 business days from the receipt
of the coordination request by NTIA. Special temporary operations may be handled with an expedited turnaround time when circumstances warrant. The operation of UWB systems in emergency situations
involving the safety of life or property may occur without coordination provided a notification procedure,
similar to that contained in CFR47 Section 2.405(a)-(e), is followed by the UWB equipment user.
Notice: Use of this device as a wall imaging system is prohibited by FCC regulations.
5 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
IMPORTANT NOTE FOR THE CANADIAN CUSTOMERS
IC Certification Number: IC:8991A – HR2000NA
This device complies with the requirements of IC Standard RSS-220
This Ground Penetrating Radar Device shall be operated only when in contact with or within 1 m of the ground.
This Ground Penetrating Radar Device shall be operated only by law enforcement agencies, scientific research
institutes, commercial mining companies, construction companies, and emergency rescue or firefighting
organizations.
NOTE IMPORTANTE POUR LES UTILISATEURS CANADIENS
Numéro de certification IC:8991A – HR2000NA
Cet appareil est conforme aux exigences de la norme RSS IC-220
Cet équipement géoradar doit être utilisé que lorsqu’il est en contact ou à moins de 1 mètre du sol.
Cet équipement géoradar doit être utilisé que par des organismes d'application de la loi, des instituts de recherche
scientifique, des sociétés minières commerciales, des entreprises de construction et de secours d'urgence ou les
organisations de lutte contre les incendies.
RADIO-FREQUENCY EXPOSURE COMPLIANCE
This product operated is usually operated at least 1 m from the operator.
Typical power density levels at a distance of 1 m or greater is below 1
W/cm2 (0.01 W/m2) which are far below the levels specified by the
current regulations.
Thus, this product pose no health and safety risk when operated in the
normal manner of intended use.
CONFORMITÉ D’EXPOSITION AUX FRÉQUENCES
RADIO
Le produit doit être à au moins un mètre de l’utilisateur lorsqu’en opération.
Le niveau de densité de puissance à une distance de 1 mètre et plus est de 1
W/cm2 (0.01 W/m2), ce qui est nettement inférieur aux niveaux spécifiés
par la réglementation en vigueur.
Ainsi, ce produit ne représente aucun risque pour la santé et la sécurité
lorsqu'il est exploité dans les conditions d'utilisation prescrites.
6 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
CLEANING INFORMATION
WARNING
Before cleaning any external parts of the apparatus, make sure
that all cables have been disconnected, including the power
supply cable. If a damp cloth is used, make sure it is not too wet,
to avoid any damage to the electrical components of the
equipment. Wait until the equipment is totally dry before
reconnecting the cables.
The Detector Duo should be cleaned periodically using a damp
cloth.
Do not use solvents or abrasive detergents.
Do not apply liquid directly to the electrical contacts of the
various connectors. If a specific spray is used to clean the PC
TFT monitor, make sure it is not flammable; ion any case, do not
spray it directly on the screen, instead, spray it onto the cleaning
cloth.
7 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
BATTERIES REMOVAL INFORMATION
Laptop Batteries:
Manufacturer: PANASONIC
Type: Li-ion Ni
Characteristics: 10.65V 5.7Ah
Removal instructions:
1. turn off the laptop;
2. open the drawer with the symbol of the batteries;
3. extract the battery pack pulling the tab.
Radar batteries:
Manufacturer: FIAMM FG21202 / SAFT MP176065
Type: rechargeable lead acid / rechargeable lithium-ion
Characteristics: 12V & 12Ah / 15V & 6.8Ah
Removal instructions:
1. disconnect the battery from the instrument:
a. pull the connector wings;
b. separate the connectors;
2. remove the battery from the cover (optional) opening the
strap.
8 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
RECICLYING
The crossed out wheeled bin symbol shown on the equipment indicates that
the product must be recycled separately from other waste at the end of its
useful life.
Separate waste disposal of this product at the end of its useful life will be
organised and managed by IDS. When you decide to dispose of the
equipment, contact IDS and follow the system that IDS has set up to permit
the separate collection of the apparatus at its life end.
Adequate separate collection for its subsequent recycling, treatment and
environmental friendly disposal contribute towards avoiding any
unnecessary effects on the environment and to health and favour the reuse or
recycling of the materials that make up the equipment. Unauthorised disposal
of this product as unsorted waste by its possessor will lead to an
administrative penalty foreseen by national regulations.
9 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
WARRANTY CERTIFICATE CONDITIONS
1) IDS Ingegneria dei Sistemi S.p.A, hereinafter referred to as IDS, warrants hardware/software
products for a period of 12 months from the delivery date to the original customer;
2) The delivery date is certified by the “Warranty Registration Form”;
3) IDS’s hardware products will be free from defects in materials workmanship under normal use and
service;
4) IDS’s obligation is limited to repairing or replacing parts or equipment which are returned to IDS,
without alteration or further damage, and which in IDS s judgment, were defective or became
defective during normal use;
5) IDS’ software will have to be installed on a PC according to the requirement of the IDS hardware (
see IDS User’s Guide the Software Data Acquisition);
6) IDS’ s software products designed by IDS for use for IDS hardware products are warranted not to
fail to execute their programming instructions due to defects during the warranty period, provided
they are properly installed on IDS hardware products. IDS does not warrant if the IDS software will
be used and operated in hardware and software combinations not selected by IDS;
7) IDS does not assumes any liability for any direct, indirect, special, incidental or consequential
damages or injuries caused by proper or improper operation of its equipment whether defective or
not defective;
8) This software may include automated data processing and analysis tools. While every effort is made
to ensure the accuracy of the information provided by those tools, they must not be intended as a
substitute for intelligent analysis; rather, they have to be intended as an advisor and the user must
not completely rely on the results provided by them to give the complete answer. IDS assumes no
liability for any direct, indirect special, incidental or consequential damages or injuries caused by
such reliance on the accuracy, reliability, or timeliness of the information provided by those tools.
Any person or entity who relies on information obtained from the automated data
processing/analysis tools only, does so at his or her own risk;
9) IDS’s warranty does not extend and shall not apply to:
a) Products which have been repaired or altered by other than IDS personnel;
b) Products which have been subjected to misuse, neglect, accident or improper installation;
c) Products in which have been installed Hardware/Software accessories not supplied by IDS
and/or without any approval by IDS;
d) Products which have been connected to equipment different from the ones supplied by IDS
(except the PC data Logger which must conform to IDS specifications;
e) Products which have been damaged by natural disaster or calamities.
10) Before returning any equipment to IDS , you have to contact the IDS Customer Care Office that will
authorize you to return the material to be repaired;
11) Once the parts/equipment to be repaired arrive to IDS, IDS may inspect the defective products to
verify they are eligible for repair or replacement. All packing must be saved for inspection purpose
in order to assist IDS to understand the cause of the defects. IDS, will not be obliged to repair, or
replace for products returned as defective but damaged from abuse, misuse, negligence , accident
loss or damage in transit;
12) The final clients, is responsible for ensuring the defective products returned to be properly
packaged;
13) The above warranty are sole and exclusive, and no other warranty, whether written or oral, is
expressed or implied.
10 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
CONTENTS
1. Introduction ........................................................................................................................... 12
1.1 Purpose .......................................................................................................................... 12
1.2 Application Field ........................................................................................................... 12
1.3 Reference ....................................................................................................................... 12
1.3.1 Applicable documents .................................................................................................... 12
1.4 Composition of the Hi-pave GPR system ....................................................................... 12
2. PROCEDURE OF ASSEMBLING...................................................................................... 14
FIGURES INDEX
FIG. 1-1– COMPOSITION OF THE HI-PAVE SYSTEM .......................................................................... 12
FIG. 2-1 – SCREW ON THE VERTICAL FRAME .................................................................................... 14
FIG. 2-2 – HORIZONTAL FRAME ATTACHED TO VERTICAL FRAME ............................................ 14
FIG. 2-3 – PARTICULAR OF THE BRACKETS TO FIX FRAME B TO FRAME A .............................. 15
FIG. 2-4 – EMBOSSED FIBERGLASS FRAME (C) .................................................................................. 15
FIG. 2-5 – ATTACHING FRAME C TO FRAME B .................................................................................. 15
FIG. 2-6 – PARTICULAR OF THE HORIZONTAL FRAME (B) LIMBS ................................................ 16
FIG. 2-7 – PARTICULAR OF THE WHITE FIBERGLASS FRAME (C) INSERTED INTO THE
INTERNAL GROOVES OF THE HORIZONTAL FRAME (B), WITH DIRECTION OF
INSERTION. ....................................................................................................................................... 16
FIG. 2-8 – PARTICULAR OF THE METALLIC LIMB AND ITS SLIT ON THE FRAME C ................. 16
FIG. 2-9 – PARTICULAR OF THE BELTS ................................................................................................ 17
FIG. 2-10 – ENCODER WHEEL KIT VIEW .............................................................................................. 17
FIG. 2-11 – PARTICULAR OF THE WHEEL MECHANICAL KIT ......................................................... 18
FIG. 2-12 – PARTICULAR OF THE WHEEL ENCODER KIT................................................................. 18
FIG. 2-13 – FINAL ASSEMBLING OF THE HI-PAVE SYSTEM ............................................................ 19
11 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
1. INTRODUCTION
1.1 Purpose
This manual explains the procedure of assembling the Hi-Pave GPR system in all its
parts.
Ids Hi-Pave system uses HR1000 and/or the HR2000 antennas; the model HR2000NA
only is allowed to operate in the US and Canadian markets.
1.2 Application Field
This system is dedicated for pavement applications on the asphalt and concrete roads. The
most common application is detecting the thickness of asphalt layers, within the first
meter of depth.
1.3 Reference
The applicable versions of the following documents are the ones officially released at the
time of the emission of this present document.
1.3.1 Applicable documents
[AD1] - MN_2008_031_11 – K2 Fast Wave User Manual
1.4 Composition of the Hi-pave GPR system
Here below you find the parts of the Hi-pave system:
ELASTIC
BELT
FIBERGLASS
HORIZONTAL
FRAME
SLIDING
CART
HORN
ANTENNA
ENCODER
VERTICAL
FRAME
HOOK
SCREW
Fig. 1-1– Composition of the Hi-Pave system
12 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
1. N.1 Aluminum Vertical Frame (A), with rectangular shape attached to a frame
provided with a hook.
2. N.1 Aluminum Sliding horizontal frame (B)
3. N.1 Embossed white fiberglass frame (C).
4. N.2 Elastic belts
5. N.1 Horn Antenna + N.1 antenna cable
6. N.1 Encoder kit + N.1 wheel encoder cable
13 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
2. PROCEDURE OF ASSEMBLING
Here below you find the steps to assemble the Hi-Pave GPR system. Of course it’s
necessary to get a vehicle provided with a hook on the back side and possibly a carrier or
similar on the roof/back of the vehicle itself. Please follow the steps in order one by one.
1. Take the metal key (provided with the system) and unscrew the screw on the
vertical frame (see Errore. L'origine riferimento non è stata trovata.), until the
frame fits on to the hook of the vehicle. Then screw it again strongly keeping the
frame vertical as much as possible (Fig. 2-1).
HOOK
SCREW
Fig. 2-1 – Screw on the vertical frame
2. Make slide the horizontal frame (B) on the vertical frame (A), and fix B to A
applying 4 screws M8x20, attaching them to the 4 brackets and verify that the B
is horizontal and parallel as much as possible to the ground surface (see Fig. 2-2
and Fig. 2-3).
HORIZONTAL
FRAME (B)
VERTICAL
FRAME (A)
Fig. 2-2 – Horizontal frame attached to Vertical frame
14 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
BRACKETS OF CONNECTION
BETWEEEN HORIZONTAL
AND VERTICAL FRAME
Fig. 2-3 – Particular of the brackets to fix frame B to frame A
3. Remove the 2 caps from the horizontal frame (B) limbs; then insert embossed
fiberglass frame (C) into the internal grooves of B until the end. Finally screw
both screws for side of B and insert again the caps (see Fig. 2-4, Fig. 2-5, Fig. 2-6
and Fig. 2-7).
Fig. 2-4 – Embossed Fiberglass frame (C)
Fig. 2-5 – Attaching frame C to frame B
15 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
CAP
CAP
REMOVED
Fig. 2-6 – Particular of the horizontal frame (B) limbs
Fig. 2-7 – Particular of the white fiberglass frame (C) inserted into the internal grooves of
the horizontal frame (B), with direction of insertion.
4. Arrange the 2 elastic belts and adapt them to the vehicle making them pass
through the metallic slits located to the limbs of the fiberglass horizontal frame
(C); then fix them on the other extremity to the vehicle (i.e. to the carrier or
similar stable supports) using its pulling mechanism (see Fig. 2-8 and Fig. 2-9).
SLIT INTO THE
METALLIC LIMB
Fig. 2-8 – Particular of the metallic limb and its slit on the frame C
16 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
BELTS
Fig. 2-9 – Particular of the belts
5. Insert the horn antenna onto the fiberglass frame in its proper place, located at the
extremity of the frame C, between 2 black cross rubber bars; then fix the top of
the antenna with the 2 straps already assembled properly.
6. The encoder kit (see Fig. 2-10) is composed by:
a. 4 metallic cylinders (Ø17, or Ø19 or Ø21)
b. 1 bigger metallic disk + 1 metallic star + 4 bigger screws
c. 1 smaller metallic disk + 1 encoder + encoder cable + 4 smaller screws +
magnet.
Fig. 2-10 – Encoder wheel kit view
17 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
Insert the 4 cylinders within the 4 nuts of the vehicle wheel and then apply on
them the bigger disk, screwing it to them by fixing 4 bigger screws; then apply the
smaller disk to the bigger disk by fixing the 4 smaller screws to the prefixed
smaller cylinders. Keep vertical the encoder cable and apply the magnet located
on its limb to the vehicle metallic side (see Fig. 2-11 and Fig. 2-12).
BIGGER
CYLINDER
BIGGER
SCREW
BIGGER
DISK
STAR PREFIXED
TO BIGGER DISK
SMALLER
CYLINDERS
Fig. 2-11 – Particular of the wheel mechanical kit
SMALLER
SCREW
WHEEL ENCODER
CABLE
SMALLER
DISK
ENCODER
Fig. 2-12 – Particular of the wheel encoder kit
18 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved
IDS Ingegneria Dei Sistemi S.p.A.
N doc:MN/2011/004 - Rev. 1.1
7. Connect the wheel cable to the wheel port of the DAD control Unit and connect
the antenna cable to antenna port of the DAD control unit.
Fig. 2-13 – Final assembling of the Hi-Pave system
19 / 19
Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati.
All information contained in this document is property of IDS. All rights reserved

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 19
Language                        : it-IT
Tagged PDF                      : Yes
Title                           : manuale d'uso
Author                          : Valter Baroncini
Creator                         : Microsoft® Word 2010
Create Date                     : 2011:12:13 17:33:09+01:00
Modify Date                     : 2011:12:13 17:33:09+01:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools