INTO TECH REALDISPLAY DVR BD User Manual Part 1

Download:
Mirror Download [FCC.gov]
Document ID	441217
Application ID	6cLPEZhiuwai5Rx97zoIvg==
Document Description	Users Manual Part 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	133.48kB (1668478 bits)
Date Submitted	2004-06-16 00:00:00
Date Available	2004-06-16 00:00:00
Creation Date	2004-06-04 14:03:54
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2004-06-04 14:03:54
Document Title	Microsoft Word - 030909 SmartDVR Formula 2.0 Manual.doc
Document Creator	Pscript.dll Version 5.0
Document Author:	into

User Manual
SmartDVR Formula v2.0
Intotech Inc.
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
Safety Notice:
zMake sure switching the power off before you install the DVR
board
zThere is possibility of electric shock inside of the DVR, please
avoid opening the unit if you are not qualified service personnel
zWhile the DVR is under removing, storing or using, please avoid
any vibration or strike
zDo not store under the direct sunlight or near by heating
zAvoid humid, dusty or smoky environments
zAvoid extremly hot or cold areas
zThis equipment should not be exposed to water or other liquids
zInstall the DVR in a well-ventilated area
zAvoid excessive electronic or magnetic fields
-2-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
Limited Warranty
This product is warranted against manufacturing defects for the period of one year.
The warranty period commences on the date of purchase from the authorized
reseller/retailer.
You original purchase invoice, showing the date of purchase of the product is your proof
of the date of purchase.
During the warranty period, defective parts will be repaired or replaced.
There will be no
charge for labor or pats during the one-year warranty period from the date of purchase.
Any shipping or other cost such as customs incurred costs, etc…. is customers’
responsibility.
This warranty does not cover any failure resulting in loss to SW, data, lost profits, lost
saving any incidental damages or other economic consequential damages due to
accident, abuse, misuse, and negligence.
Technical Support and Service
For warranty service and assistance, it is recommended that you contact the place of
purchase to arrange for return and/or repair the product.
-3-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
Table of Contents
Chapter 1 Introduction
Page
1-1. General Guidelines
1-2. System Requirements and Description
1-3. Compatible HW Device
Chapter 2 Installation
2-1. Hardware Installation
-8-
2-1-1. DVR Board Installation
-9-
2-1-2. Extension Board Installation
-11-
2-1-3. Pan/Tilt/Zoom Installation
-13-
2-1-4 Audio Installation
-17-
2-2. Software Installation
-19-
2-2-1 Installation Procedure
-19-
2-2-2. Install DVR Server
-20-
2-2-3 Apache Web Server Installation
-24-
2-2-4 WebClient Installation
-30-
2-2-4. Uninstall DVR Server
-32-
-4-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
Chapter 3 User Manual for DVR Server
୔ Preview of DVR Server v2.0 Screen Mode
Monitoring screen Mode of DVR Server
Search screen mode of DVR Server
3-1. Main features and functions
-33-
3-2. Monitoring Screen Mode
-35-
୔ DVR System Configuration
-38-
1) General
-38-
2) Channel
-40-
3) Store
-42-
4) Network
-44-
5) Schedule
-47-
6) Maintenance
-49-
7) Event
-50-
8) Receiver
-53-
9) VideoOut
-54-
10) User Management
-55-
3-3. Search Mode
-57-
୔ Print Image
-58-
୔ How to use Watermarking
-60-
୔ Search
-64-
Chapter 4 Warranty
୔ Warranty
-66-
-5-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
Chapter 1: Introduction
Chapter 1
Thank you for purchasing DVR. This manual will provide detailed instructions on how to install and
program DVR to your specific application. Please read this manual carefully prior to install and
programming the DVR.
1-1. General Guidelines
Chapter 1: System Requirements and Compatible H/W information
Chapter 2: DVR Hardware, Software Installation
Chapter 3: How to use DVR Server program
Chapter 4: Warranty
1-2. DVR System Requirements
PC
TG OS : Windows 2000 (Require DirectX 8.1 or higher) and Windows XP
Please install 8.1 version of DirectX before install DVR Server Program
on Server PC for Windows 2000 Only
TG CPU : Intel Pentium 4
2.4/ Cel 1.7 or higher
TG RAM : 256MB or higher
TG Network : 10 /100Mbps LAN, Modem, xDSL
System Description
Digital Surveillance System is a PC based monitoring system. It exceeds the capabilities of the
traditional analog switchers, multiplexers, and time-lapse VCRs. The system is able to connect
up to 16 cameras with each at the high frame rate, records high-quality digital video based on
motions. The system offers digital recording, remote camera viewing access, video archiving,
and multi-camera display. The system supports PTZ camera.
-6-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
1-3. Compatible HW Device
Compatible
Intel Pentium Process (x86, 1.7GHz or
higher)
CPU
- Intel Celeron 1.7GHz or higher
Incompatible
- Lower than Intel Pentium Process
1.7GHZ
- Other than x86
- Intel Pentium IV
With one or more PCI slot, supporting Intel - Other than Intel Chipset Boards
Pentium processor
- Intel 84x Chipset
Main Board
- Intel 85x Chipset
With 8MB or higher memory, Supporting - Intel 81x Graphics controller(OnBoard)
16Bit Color and YuY2 DirectX Mode (8.0 or
higher)
- ATI Expert 2000 32MB SDRAM
Graphic Card
- ATI Radeon System
- nVidia Riva TNT2 System
or Intel i740
- VIA Chipset(OnBoard) Graphics
controller.
- SIS Chipset(OnBoard) Graphics
controller.
- nVidia Geforce System
- Intel 845G/GL Graphics controller
(OnBoard).
Sound Card
HDD
All PCI & OnBoard Type
HDD 5400RPM or higher
-7-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
Chapter 2: Installation
Chapter 2
2-1 Hardware Installation
Caution: Static electricity can damage electronic circuitry. To avoid static
discharge, touch a grounded metal object (i.e. your PC case) or wear a
grounding strap connected to a ground source.
Make sure Power and cables are connected properly otherwise it may cause
damage to the equipment (not cover under warranty). Always turn off the
PC power before connecting or disconnecting any jumper or cable on the
drive.
- Next Page-
-8-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
2-1-1. DVR Board Installation
1. Prepare your computer for installation.
: Before working on your computer, make sure all electrical cords are unplugged.
2. Remove the system unit cover.
: You can easily find how to remove the system unit cover if you look carefully at the back of
the system.
3. Locate the PCI bus slot. Make sure this slot is unobstructed.
: You need empty PCI slot as many as the boards including DVR and channel boards.
ཛ PCI slotG
4. Place the board directly over PCI slot and insert one end of the card down into the slot
firmly but gently. Make sure that the metal contacts on the bottom of the host adapter are
securely seated in the slot.
-9-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
ཛ DVR board
5. Fasten the bracket screw.
6. Connect channel board to 5~8ch parallel connector on DVR board
Position of ‘channel parallel connector’ might be different up to DVR model.
Please refer to ‘2.1 DVR board is drawing’ for parallel connector position.
All the optional channel boards and channel board cables are same and alternative.
-10-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
2-1-2. Extension board Installation
XaGChannel Cable
2: Parallel Connector on channel board
3: 5~8ch Parallel Connector on DVR board.
-11-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
7. Connect channel board to ‘9~12ch parallel connector on DVR board’ and insert the
channel into the PCI slot.
1: 9~12ch parallel connector on DVR board
8. Connect channel board to ‘13~16ch parallel connector on DVR board’ and insert the
channel into the PCI slot.
-12-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
2-1-3. PTZ installation
1: 13~16ch
parallel
on DVR
A. PTZ
Cable connector
Connection.
1. Insert the plug of PTC cable into the PC case through proper hole.
ཛG Plug of PTZ cable
ཛྷG 485 cable of PTZ cableG
ཝG Serial Port of PTZ cableG
2. Insert the plug of PTC cable into the ‘PTZ parallel connector on DVR board’.
Position of ‘PTZ parallel connector’ might be different up to DVR model. Please refer to ‘2.1
DVR board drawing’ for parallel connector position.
1: PTZ parallel connector on DVR board
-13-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
3. Locate the empty serial comport on rear side of PC.
1: Serial Comport 1 or 3
2: Serial Comport 2 or 4G
4. Insert the serial port of PTZ cable into empty serial port of PC.
1: Serial port of PTZ cable
-14-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
5. Connect 485+ cable of PTZ cable with 485+ cable of PTZ camera and 485- cable of PTZ cable
with 485- cable of PTZ camera. And, insulate them with insulating tape.
XG: 485+ cable connection
YG: 485- cable connectionG
6. Connect video signal cable of PTZ camera with BNC jack on DVR.
7. Address of PTZ camera should be identical to DVR channel. In the Fig 4.11, the address
of PTZ camera should be set as ‘1’, because camera is connected to No.1 channel.
- Next Page -
-15-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
1: BNC Jack of Channel
8. Connect the adaptor with PTZ camera.
-16-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
2-1-4. Audio installation
1. Insert MIC to sound card OR DVR board.

MIC is inserted to PC Mainboard. (Standard color red hole)
OR Insert MIC to DVR Board.
-17-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
2. Insert Speaker to Sound Card of motherboard. (standard Green color hole)
-18-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
2-2 DVR Server Software Installation
Select one application to install at a time
2-2-1. Preview Installation Procedure
1. Install SmartDVR Formula
SW
Y. Install Apache HTTP SWG
Z. Install WebClient SWG
Attention: If an older version of SW has been already installed on your computer, you should
uninstall the older version first.
-19-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
2-2-2. Install DVR Server Software (Important)
Installation
Procedure
Run the Setup.exe (
1. Install SmartDVR Formula SW
2. Install Apache HTTP SW
3. Install WebClient Formula SW
) file.
InstallShield Wizard is executed. Press the [Next] button
- Next Page –
-20-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
3. If you accept all the terms of the License Agreement, Press the [Yes] button
4. Select the folder of destination and Press the [Next] button.
-21-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
5. Press the [Finish] button to complete installation.
6. Driver Auto installer for Windows XP.
7. Press the [Yes] button to complete Auto Driver Installation
Reboot system for stable operation
-22-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
2-2-3. Apache Web Server Installation
1. Run Apache Web Server[
] program.
2. The screen will display as following: Click [Next] button.
3. Read the license agreement. If you agree click [I accept…] and click [Next] button.
-23-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
4. Confirm Apache Server information and click [Next] button.
5. Insert Network Domain, Server Name, Administrator’s Email Address.
(For formality purpose only. Insert any address.)
Select [Run as a service for All Users – Recommended]. Click [Next] button.
-24-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
6.Select [Complete] for Setup Type. Click [Next] button.
7. Click [Next] button. Attention: Do not change directory.
-25-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
8. Click [Install] button and start installation.
9. Click [Finish] button when completion of installation program.
-26-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
10. Change the port of Apache HTTP Server.
(Windows – Start - Program – Apache Http Server
– Select Configure Apache Server – Edit the Apache Http conf…
11. The screen will display as following: Select Edit – Find.
-27-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
12. Insert “port 80” and press enter. Port 80 will view as following:
13. Change Port 80 to Port 26540 and save Notepad.
14. Exit Notepad after Save.
z Attention: Must add port number after IP address to view in Internet Web Browser.
z Ex) http://211.104.32.107:26540
-28-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
2-2-4.Web Client Formula Installation
1. Run Web Client Formula (
) file.
2. The InstallShield Wizard will display as following: Click [Next] button.
3. Read License Agreement carefully. When accept of agreement click [Yes] button.
-29-G
GGGGGGGGGGGGGGGGGGGGGGGGGGGGGGG
SmartDVR Formula 2.0G
4. Click [Finish] after completion of installation.
-30-G

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 30
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:f2170267-2a9d-4007-8f30-9720e94e4516
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2004:06:04 14:03:54+09:00
Modify Date                     : 2004:06:04 14:03:54+09:00
Creator Tool                    : Pscript.dll Version 5.0
Document ID                     : uuid:d2f5997d-fe9d-4f3f-87bd-8a4a683f32a7
Format                          : application/pdf
Creator                         : into
Title                           : Microsoft Word - 030909 SmartDVR Formula 2.0 Manual.doc
Author                          : into

EXIF Metadata provided by EXIF.tools