Contents
- 1. Manual DP 250
- 2. Manual DP 550
- 3. Manual DP 550P
Manual DP 550
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 709326 |
| Application ID | a7cWkkp2CTDIg8eelTMQwQ== |
| Document Description | Manual DP 550 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 43kB (537545 bits) |
| Date Submitted | 2006-09-26 00:00:00 |
| Date Available | 2006-09-26 00:00:00 |
| Creation Date | 2006-07-27 11:43:00 |
| Producing Software | Acrobat Distiller 6.0 (Windows) |
| Document Lastmod | 2006-09-22 09:34:30 |
| Document Title | ä¸æ–‡ç›®éŒ„ |
| Document Creator | Acrobat PDFMaker 6.0 for Word |
| Document Author: | Jesse Huang |
PIR + Microwave Motion Detector DUOGUARD DP-550 GENERAL Thank you for choosing IR-TEC dual technology motion detector for your security system. The DP-550 is a compact motion detector that combines a passive infrared (PIR) and a microwave (MW) motion sensor. The alarm signal will be transmitted when both sensors detect the motion at the same time. It provides superior reliability in intrusion detection to your alarm system. A unique ceiling/wall mount bracket is provided for easy adjustment of detection coverage. Installation Instructions DESCRIPTION INSTALLATION HINTS The DP-550 may be either wall or corner mounted by applying different knockouts. The provided mounting bracket can be applied for ceiling or wall mount. Corner mount is recommended for optimum detection. Do not install where the detector is in or facing direct/reflected sunlight, window onto main road to avoid MOUNTING OPTIONS Ceiling Mount car head light. Ensure that there are not any obstructions (plants, screens, furniture etc.) in the field of view which may block the detection. The detector should not face to the ventilation of HVAC or any equipment that may produce strong temperature change. Light Min. 1m TAMPER Locate the detector at least 1 meter away from the nearest fluorescent light to avoid interference to MW sensor. The tamper protection will be activated if the locking screw of front cover and bottom case is loosen. Ensure to fix the screw. Avoid running the alarm cable along with AC mains cables !!! Wall Mount MOUNTING & WIRING With mounting bracket 1. 2. 3. Mount the base of mounting bracket on the selected position. Lead the cable through the cable access tunnel of mounting bracket. Open the front cover and carefully remove the PCB from the bottom case. Lead the cable into the case and assemble the mounting bracket with it (as shown on previous page). Connect the cable to the corresponding terminals according to the following instructions. Replace the PCB on the bottom case and fix it. Replace the front cover and then walk test can be conducted. Without mounting bracket 1. 2. Open the front cover and carefully remove the PCB from the bottom case. Select the adequate knockouts and mount the case on the position. Connect the cable to the corresponding terminals according to the following instructions. Replace the PCB on the bottom case and fix it. Replace the front cover and then walk test can be conducted. Code Description Placed (ON) Removed (OFF) MW sensor Enable MW LED Disable MW LED detection indication indication ALM Alarm relay Enable alarm LED Disable alarm LED output indication indication O/P Output format N.O. output N.C. output PIR PIR sensor Enable PIR LED Disable PIR LED detection indication indication MW Pulse count selection Code SWA SWB Pulse count 1 ON OFF Pulse count 2 OFF ON Pulse count 3 OFF OFF DETECTION PATTERN Model: DP-550 110°, 15 x 15m at 25°C Top View Side View 110° Wiring Diagram ALARM 2.2m TAMPER 1m Tamper output (NC) Alarm output (NC/NO) Power input (9 ~ 16 VDC) TAMPER: Connect to the tamper protection loop. ALARM: Alarm output (NC/NO) – : Ground of DC power input. +: Positive of DC power input. WALK TEST It is necessary to carry out a thorough walk test of the detector to ensure that the correct coverage is being achieved. Also to ensure that both PIR & microwave are sensors working to the same detection area. 1. Apply the DC power supply and give about 60 seconds for sensor to warm up. After the warm up time expires, walk across the detection zones at normal speed. The red LED will lit when it detects the motion. 2. If microwave sensor is over sensitive (green LED remains on), adjust of the thumb wheel of MW sensitivity trimmer in counterclockwise until ideal detection range is obtained. 2.5m A 6x2-pin jumper switch is available for various settings of the detector. Please refer the following instructions for setting options. 15m SPECIFICATIONS Power supply ............9 ~ 16 VDC, 12 VDC typical Current drain.............30 mA @ 12 VDC Infrared sensor..........Dual element, pyroelectric Microwave sensor.....DRO, patch antenna MW Frequency .........10.525 GHz MW output power .....6 mW E.I.R.P. peak Alarm period .............1.5 ~ 2.5 seconds Alarm output .............NC/NO, 30 VDC, 0.2A max. Tamper protection ....NC, screw release activated Mounting height........1.8 ~3.6 m Mounting bracket......MB-99 included(DP-550-B) Detectable speed......0.1~3.0 m/sec. RFI immunity.............Av. 20 V/m (10~1,000 MHz) Temperature .............-20°C~50°C (-4°F ~ 122°F) Humidity....................95% RH max. Dimensions ...............112 x 66 x 45 mm Warning: Changes or modifications this nit not expressly approved by the party responsible for compliance could void the user’s authority to operate the eqipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: JUMPER SWITCH SETTING 8m (1) This device may not cause harmful interference, and (2) This device must accept any interference received, Including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 2 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:1e425e2f-5a08-4009-a0b8-9173bbd1a9ff Producer : Acrobat Distiller 6.0 (Windows) Company : IR-TEC Source Modified : D:20060727034254 Headline : Creator Tool : Acrobat PDFMaker 6.0 for Word Modify Date : 2006:09:22 09:34:30-04:00 Create Date : 2006:07:27 11:43:00+08:00 Metadata Date : 2006:09:22 09:34:30-04:00 Document ID : uuid:17e4aa86-577b-4327-97ed-ed7069fcf190 Version ID : 6 Format : application/pdf Title : 中文目錄 Creator : Jesse Huang Subject : Tagged PDF : Yes Author : Jesse HuangEXIF Metadata provided by EXIF.tools