InnoSenT 2 Doppler Radar Module User Manual Installation Manual

InnoSenT GmbH Doppler Radar Module Installation Manual

Installation Manual

1 von 3 DATA SHEET IPS-265_F 11-01-2011 Version 0.3 _____________________________________________________________________________________________________ User Manual Product Family: Low Cost K-Band Transceiver Range of use: Security- / Door- applications Module Number: IPS-265_F _____________________________________________________________________________________________________ Description: ♦ radar-based motion detector ♦ available in different frequency ranges: Standard; _F and _UK variants ♦ advanced PHEMT-oscillator with low current consumption ♦ split transmit and receive path for maximum gain ♦ dual (stereo channel) operation ♦ very small outline dimensions Block Diagram: Environmental Tests and Handling Precautions: ♦ This InnoSenT sensor is sensitive to damage from ESD. ♦ Normal precautions as usually applied to CMOS devices are sufficient when handling the device. Touching the signal output pins has to be avoided at any time before soldering or plugging the device into a motherboard ♦ Applying multimeters e.g. for resistance measurement between any of the connector pins may cause damage to the module. ~ Oscillator I/Q-Mixer Tx Rx S1 S2
2 von 3 DATA SHEET IPS-265_F 11-01-2011 Version 0.3 Electrical Characteristics: Parameter Symbol min. typ. max. units comment Transmitter transmit frequency f24.075 IPS-265_F 24.175 GHz temperature drift frequency ∆f -1 MHz/°C output power P out 16 dBm positive supply voltage Vcc 5 V positive supply current Icc 30 40 mA Receiver I/Q-balance amplitude 6 db phase 60 90 120 ° IF-output voltage offset -300 300 mV Environment operating temperature T -20 OP 60 °C outline dimensions ~ 25 x 25 x 7 (12.7) mm compare drawing Antenna antenna pattern (-3 dB) horizontal 80 ° azimuth vertical 32 ° elevation side lobe suppression horizontal 13 dB azimuth vertical 13 dB elevation Mechanical Outlines:
3 von 3 DATA SHEET IPS-265_F 11-01-2011 Version 0.3 Interface: The sensor provides a 2.54 mm grid, single row pin header (square pin  0.635 mm). Pin Function Description 1 NC not connected 2 VCC supply voltage 5V 3 IF1 signal 1 output 4 GND GND 5 IF2 signal 2 output Certification and environment protection: InnoSenT GmbH has established and applies a quality system for: Development, production and sales of radar sensors for commercial and industrial sensors An audit was performed, Report No. 010350 Proof has been furnished that the requirements according to DIN EN ISO 9001:2000 are fulfilled. This InnoSenT product is compliant to the restriction of hazardous substances (RoHs – European Union directive 2002/95/EG). FCC approval • This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Warning: Changes or modifications made to this equipment not expressly approved by InnoSenT GmbH may void the FCC authorization to operate this equipment. • Manufacturers of mobile or fixed devices incorporating IPS-265_F modules are authorized to use the FCC Grants and IC Certificates of the IPS-265_F modules for their own final products according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID: UXS2" and "Contains IC: 5904A-UXS2". Contact Information: InnoSenT GmbH Am Roedertor 30 97499 Donnersdorf Germany Phone: +49 (0) 9528-9518-0 Fax: +49 (0) 9528-9518-99 E-Mail: info@InnoSenT.de Web: www.InnoSenT.de

Navigation menu