InnoSenT IPQ05R05 Stereo K-Band Transceiver Module User Manual IPQ 05 Rev 05

InnoSenT GmbH Stereo K-Band Transceiver Module IPQ 05 Rev 05

User Manual

Innovation in radar sensing Making happen what others only dream of Innovation in radar sensing Making happen what others only dream of 1 von 3 USER MANUAL IPQ-05_Rev.05 2008-05-19 Version 1.0 _____________________________________________________________________________________________________ USER MANUAL Product Family: K-Band Transceiver Range of use: advanced door applications Module Number: IPQ-05_Rev.05 _____________________________________________________________________________________________________ Description: Basic Features IPQ-05_Rev.05 - radar-based motion detector centered @ 24.125 GHz - advanced PHEMT-oscillator with low current consumption - split transmit and receive path for maximum gain - stereo (dual channel) operation for direction of motion identification - integrated IF-pre-amplifier - enable input for oscillator shut down - small outline dimensions - two electronically selectable antenna patterns - EN 61508:2001 certification requires that the transceiver is built into a housing rated 0. min. IP20 for indoor use 1. min. IP54 for outdoor use Electrical Characteristics Parameter Symbol min. typ. max. units comment transmit frequency ftransmit 24.075 24.125 24.175 GHz output power (EIRP) Pout 15 20 dBm temperature drift ∆f - 1 MHz/°C I/Q balance amplitude 6 dB phase 60 90 120 ° IF-output voltage offset 1.0 4.0 V IF-amplifier 1 gain 23 dB bandwidth DC 220 * kHz * typical upper frequency limit switching voltage 2 high level 2 5.5 V narrow antenna pattern low level GND 0.5 V broad antenna pattern supply voltage VCC 4.75 5.0 5.25 V supply current ICC 35 50 mA threshold for enable input 3 min off VCC-0.2 V max on 0.5 V turn-on time oscillator ton 0.5 5 µs turn-off time oscillator toff 1 5 µs step response 40 mV absolute value (Delta S1)+ absolute value (DeltaS2) operating temperature TOP - 20 + 60 °C outline dimensions ~ 40 x 25 x 24 mm 1Output-Impedance Rout(IF1, IF2) = 100 Ω 2no Pullup or Pulldown-Resistor 3Internal Pullup-Resistor with 10kΩ
Innovation in radar sensing Making happen what others only dream of Innovation in radar sensing Making happen what others only dream of 2 von 3 USER MANUAL IPQ-05_Rev.05 2008-05-19 Version 1.0 Antenna Characteristics (radiation pattern) Rx1 Tx Rx2 Parameter Symbol min. typ. max. units comment antenna pattern Tx (3dB) horizontal 76 ° azimuth vertical 35 ° elevation antenna pattern Tx (10dB) horizontal 135 ° azimuth vertical 62 ° elevation side lobe suppression Tx horizontal 13 dB azimuth vertical 13 dB elevation antenna pattern Rx1 (3dB) horizontal 76 ° azimuth vertical 35 ° elevation antenna pattern Rx1 (10dB) horizontal 135 ° azimuth vertical 62 ° elevation side lobe suppression Rx1 horizontal 13 dB azimuth vertical 13 dB elevation antenna pattern Rx2 (3dB) horizontal 49 ° azimuth vertical 40 ° elevation antenna pattern Rx2 (10dB) horizontal 89 ° azimuth vertical 69 ° elevation side lobe suppression Rx horizontal 13 dB azimuth vertical 13 dB elevation Interface The sensor provides a 2 mm pitch 6 pin connector Molex 51004-0600. Pin # Description In/Out Comment 1 enable input active low 2 VCC input supply voltage (+5 V) 3 GND input analog ground 4 IF1 output Signal I(nphase) 5 IF2 output Signal Q(uadrature) 6 switch input mates with: Molex P/N 53014, 53015 and 53025 Mechanical Outlines all dimensions in mm for details compare with drawing 41-1190.42 vertical horizontal
Innovation in radar sensing Making happen what others only dream of Innovation in radar sensing Making happen what others only dream of 3 von 3 USER MANUAL IPQ-05_Rev.05 2008-05-19 Version 1.0 I/Q-Definition Signal Q is leading if an object moves towards the radar transceiver. Certification and Environment Protection InnoSenT GmbH has established and applies a quality system for: Development, production and sales of radar sensors for commercial and industrial sensors An audit was performed, Report No. 010350 Proof has been furnished that the requirements according to DIN EN ISO 9001:2000 are fulfilled. This InnoSenT product is compliant to the restriction of hazardous substances (RoHs – European Union directive 2002/95/EG). FCC-Approval • This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Warning: Changes or modifications made to this equipment not expressly approved by InnoSenT GmbH may void the FCC authorization to operate this equipment. • Manufacturers of mobile or fixed devices incorporating IPQ-05 modules are authorized to use the FCC Grants and IC Certificates of the IPQ-05 modules for their own final products according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID: UXS-IPQ05R05" and "Contains IC: 6902A-IPQ05R05". Contact Information: InnoSenT GmbH Am Roedertor 30 97499 Donnersdorf Germany Phone: +49 (0) 9528-9518-0 Fax: +49 (0) 9528-9518-99 E-Mail: info@InnoSenT.de Web: www.InnoSenT.de

Navigation menu