InnoSenT IPS154US K-Band Transceiver Module User Manual 154 US User Manual

InnoSenT GmbH K-Band Transceiver Module 154 US User Manual

User Manual

Version 1.0 IPS-154_US page 1 of 3 2007-06-06 User Manual Product Family: K-Band Transceivers K-Band Transceiver with two integrated patch antennas and IF-pre-amplifier IPS-154_US Description: - radar-based motion detector - advanced PHEMT-oscillator with low current consumption - split transmit and receive path for maximum gain - stereo (dual channel) operation for direction of motion identification - IF-pre-amplifier, bandwidth limited for lowest noise performance - economic flat-pack housing, extra small outline dimensions - enable input for oscillator shut down Absolute Maximum Ratings: Parameter Symbol Rating Units supply voltage VCC 5.5 V operating temperature (out of spec) TOP - 40 / + 85 °C storage temperature TSTG + 90 °C Electrical Characteristics: Parameter Symbol min. typ. max. units comment fIPS-154_US 24.075 24.125 24.175 GHz output power (EIRP) Pout 16 20 dBm temperature drift ∆f - 1 MHz/°C antenna pattern horizontal 45 ° azimuth vertical 38 ° elevation side lobe suppression horizontal 13 dB azimuth vertical 13 dB elevation I/Q balance amplitude 6 dB phase 60 90 120 ° IF output voltage offset 1.0 2.2 4.0 V IF-amplifier gain 20 dB bandwidth DC – 50 kHz supply voltage VCC 4.75 5.0 5.25 V supply current I 35 50 mA operating temperature TOP - 20 + 60 °C outline dimensions 44 x 30 x 8.3 (19) mm compare drawing
Version 1.0 IPS-154_US page 2 of 3 2007-06-06 Interface: The sensor provides a 2.54 mm grid, single row pin header (square pin  0.635 mm). Pin # Description In/Out Comment 1 NC not connected 2 enable input active low 3 VCC input supply voltage (+5 V) 4 GND input analog ground 5 IF1 output Signal I(nphase) 6 IF2 output Signal Q(uadrature) 7 NC not connected 8 NC not connected 9 GND input analog ground 10 NC not connected Mechanical Outlines: (dimensions in mm) Certification and environment protection: InnoSenT GmbH has established and applies a quality system for: Development, production and sales of radar sensors for commercial and industrial sensors An audit was performed, Report No. 010350 Proof has been furnished that the requirements according to DIN EN ISO 9001:2000 are fulfilled. This InnoSenT product is compliant to the restriction of hazardous substances (RoHs – European Union directive 2002/95/EG). azimuth elevation
Version 1.0 IPS-154_US page 3 of 3 2007-06-06 FCC approval • The product variant IPS-154_US device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Warning: Changes or modifications made to this equipment not expressly approved by InnoSenT GmbH may void the FCC authorization to operate this equipment. • Manufacturers of mobile or fixed devices incorporating IPS-154 modules are authorized to use the FCC Grants and IC Certificates of the IPS-154 modules for their own final products according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID: UXS-IPS154US". Contact Information: InnoSenT GmbH Am Roedertor 30 97499 Donnersdorf Germany Phone: +49 (0) 9528-9518-0 Fax: +49 (0) 9528-9518-99 E-Mail: info@InnoSenT.de Web: www.InnoSenT.de

Navigation menu