InnoSenT IVS979 24 GHz Doppler Module User Manual Installation Manual

InnoSenT GmbH 24 GHz Doppler Module Installation Manual

Installation Manual

InnoSenT sets standards – worldwidePage 1 Version 1.0 DATA SHEET IVS-979Installa on Manual IVS-979 Version 1.0 - 15.03.2012The IVS-979 is a K-Band VCO Transceiver with advanced SiGe MMIC technology that can be operated in FSK and FMCW mode.The sensor provides a special RF-design for maximum sensi! vity in long range appli-ca! ons such as traffi c monitoring or speed enforcement.Another smart new feature is the 1/x divider output for VCO tuning slope lineariza! on.InnoSenT GmbH has established and applies a quality system for: development, produc-! on and sales of radar sensors for commer-cial and industrial sensors.An audit was performed, Report No. 010350 Proof has been furnished that the requirements according to DIN EN ISO 9001:2000 are fulfi lled.This product is compliant to the restric! on of hazardous substances (RoHS - European Union direc! ve 2002/95/EG)Features: »K-Band VCO Transceiver with advanced SiGe MMIC technology »FSK / FMCW modes »1/x divider for reference frequency output »stereo (dual channel) opera! on to detect direc! on of mo! on »integrated RF-pre-amplifi erProduct Family Applica onsK-Band VCO Transceiver with advanced MMIC technology» Traffi c Monitoring Movement Velocity Direc! on Presence Distance AngleCONFIDENTIAL AND PROPRIETARYThe informa! on contained in this document shall remain the sole and exclusive property of InnoSenT GmbH and shall not be disclosed by the recipient to third par! es without prior consent of InnoSenT in wri! ng.Descrip! on Cer! fi cates
InnoSenT sets standards – worldwidePage 2 Version 1.0 DATA SHEET IVS-979Oscillatortransmit frequencies f 24.000 - 24.250 GHz depending on Vtunevaractor tuning voltage Vtune 0 3 Vtuning bandwidth fi ne DC 500k Hztuning bandwidth coarse DC 0.4 Hzinput impedance Vtune fi ne 1 kΩ 200pf ESD protec# oninput impedance Vtune coarse 1 kΩ 200pf ESD protec# ontuning slope coarse 340 552 766 MHz/Vtuning slope fi ne 59 96 133 MHz/Vtemperature dri$ frequency Δf -4 -5 MHz/°Couput power (EIRP) Pou-ETSI 20 dBm @ room-temperatureout of band radia# on (EIRP) Pout of band -30 dBm @ room-temperaturedivider ra# o factory se& ng 1,280 for example 24.200GHz lead to 1.18MHzReceiverIF-amplifi er gain 40 dB part number LT6204bandwidth 100 2.5M Hzoutput impedance 100 Ωsignal level S I/Q t.b.d. mV @ InnoSenT Test setupR I/Q t.b.d. mV @ InnoSenT Test setupIF-output voltage off set 1.65 VI/Q balance amplitude 6 dBphase 70 95 120 °Antenna pa! ern (compare with antenna pa! ern on page 4)antenna pa* ern (@3dB) horizontal 7 ° azimuthver# cal 28 ° eleva# onside lobe suppression horizontal 15 dB azimuthver# cal 15 dB eleva# onPower Supplysupply voltage VCC 5.3 5.5 6 V max. 1mVPP ripplesupply current ICC 170 mAEnvironmentopera# ng temperature TOP -30 +60 °Cstorage temperature TSTG -30 +85 °Coutline dimensions 120 x 72.5 x 10.65 (17.7) mm compare drawingElectrical Characteris" csParameter Symbol Min. Typ. Max. Units CommentCONFIDENTIAL AND PROPRIETARYThe informa# on contained in this document shall remain the sole and exclusive property of InnoSenT GmbH and shall not be disclosed by the recipient to third par# es without prior consent of InnoSenT in wri# ng.Handling Precau" onsThis InnoSenT sensor is sensi# ve to damage from ESD.Normal precau# ons as usally applied to CMOS devices are suffi cient when handling this device.Touching the signal output PINs has to be avoided at any # me before soldering or plugging the device into a motherboard.
InnoSenT sets standards – worldwidePage 3 Version 1.0 DATA SHEET IVS-979Tx - antenna pa ern1 MUXOUT OUT-digital reference signal VCO frequency already divided by prescaler2 GND ground3 VCC IN-analog 5.5V supply voltage4 SPI_CLOCK IN-digital SPI-clock5 SPI_DATA IN-digital SPI-data6 PLL_LE IN-digital latch enable PLL7 d.n.c. do not connect8 CUST_PROG_LE IN-digital enable customer programming (ac! ve low)9 d.n.c. IN-digital do not connect10 d.n.c. do not connect11 d.n.c. do not connect12 Q-SIGNAL OUT-analog IF-output-signal13 I-SIGNAL OUT-analog IF-output-signal14 Vtune coarse IN-analog tuning voltage for coarse tuning VCO15 Vtune fi ne IN-analog tuning voltage for fi ne tuning VCOPin # Descrip! on In / Out CommentCONFIDENTIAL AND PROPRIETARYThe informa! on contained in this document shall remain the sole and exclusive property of InnoSenT GmbH and shall not be disclosed by the recipient to third par! es without prior consent of InnoSenT in wri! ng.Interfacefull beam width @ -3dB horizontal 7 °ver! cal 28 °side-lobe suppression horizontal 15 dBvertical 15 dBParameter Symbol Min. Typ. Max. Units Commentoutput power [dBm]angle [°]The sensor provides a 2.54mm grid pin header.-40-35-30-25-20-15-10-50-180,0 -150,0 -120,0 -90,0 -60,0 -30,0 0,0 30,0 60,0 90,0 120,0 150,0 180,0
InnoSenT sets standards – worldwidePage 4 Version 1.0 DATA SHEET IVS-979Mechanical OutlinesAll dimensions in mmChanges or modifi ca" ons made to the equipment not expressly approved by InnoSenT GmbH may void the FCC / IC authoriza" on to operate this equipment.The use of the transceiver module is authorized in mobile or fi xed host devices taking into account the condi" ons listed below:• OEM Integrator must ensure that the end user manual may not contain any informa" on about the way to install or remove the module from the fi nal product.• Depending on the fi nal host device addi" onal authoriza" on requirements for the non-transmi# er func" ons of the transmi# er module may be required (i.e., Verifi ca" on, or Declara" on of Conformity) The OEM integrator is responsible for ensuring that a$ er the module is installed and opera" onal the host con" nues to be compliant with the Part 15B uninten" onal radiator require-ments.• The informa" on on the label and in the user manual is required to be incorporated in the user manual of the fi nal host. see 47 CFR15 requirements for more details (e.g. 15.19 / 15.21 / 15.101 / 15.105 / RSS-GEN / ICES)• Addi" onal label with the words ‘Contains FCC ID:AAABBBBB’ and ‘Contains IC:AAAA-BBBB’ shall be applied and visible from the outside of the host product.• The module must be installed and used in strict accordance with the manufacturer’s inst-ruc" ons as described in the user documenta" on that comes with the module.• The end user manual for the fi nal host product opera" ng with this transmi# er must inclu-de opera" ng instruc" ons to sa" sfy RF exposure compliance requirements. e.g
InnoSenT sets standards – worldwidePage 5 Version 1.0 DATA SHEET IVS-979Contact Informa onInnoSenT GmbH | Am Roedertor 30 | 97499 Donnersdorf | GermanyPhone: +49 (0) 9528-9518-0 | Fax: +49 (0) 9528-9518-99 | E-Mail: info@innosent.dewww.innosent.deInnoSenT GmbHAm Rödertor 3097499 DonnersdorfGERMANYApprovalThis Data Sheet contains the technical specifi ca" ons of the described product. Changes of thespecifi ca" on must be in wri# en form. All previous versions of this Data Sheet are no longer valid.The technical specifi ca" ons of this Data Sheet are approved by:Radiofrequency radia" on exposure Informa" on:This equipment complies with FCC radia" on exposure limits set forth for an uncontrolled environ-ment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.This transmi# er must not be co-located or opera" ng in conjunc" on with any other antenna or transmi# er.• When the fi nal host product opera" ng with this transmi# er deviate from above, installa" -on of this module into specifi c fi nal hosts may require the submission of a Class II permissive change applica" on containing data per" nent to RF Exposure, spurious emissions, ERP/EIRP, and host/modu-le authen" ca" on, or new applica" on if appropriate.Feel free to contact us if addi" onal guidance is required.Manual Requirements according 15.19 / RSS-GENThis device complies with Part 15 of the FCC Rules [and with Industry Canada licence-exempt RSS standard(s)].Opera" on is subject to the following two condi" ons:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera" on.Manual Requirements according 15.21Changes or modifi ca" ons made to this equipment not expressly approved by (manufacturer name) may void the FCC authoriza" on to operate this equipment.

Navigation menu