InnoSenT IVS979 24 GHz Doppler Module User Manual Installation Manual
InnoSenT GmbH 24 GHz Doppler Module Installation Manual
InnoSenT >
Installation Manual
InnoSenT sets standards – worldwide
Page 1 Version 1.0 DATA SHEET IVS-979
Installa on Manual IVS-979
Version 1.0 - 15.03.2012
The IVS-979 is a K-Band VCO Transceiver
with advanced SiGe MMIC technology that
can be operated in FSK and FMCW mode.
The sensor provides a special RF-design for
maximum sensi! vity in long range appli-
ca! ons such as traffi c monitoring or speed
enforcement.
Another smart new feature is the 1/x divider
output for VCO tuning slope lineariza! on.
InnoSenT GmbH has established and applies
a quality system for: development, produc-
! on and sales of radar sensors for commer-
cial and industrial sensors.
An audit was performed, Report No. 010350
Proof has been furnished
that the requirements
according to DIN EN ISO
9001:2000 are fulfi lled.
This product is compliant to
the restric! on of hazardous
substances (RoHS - European
Union direc! ve 2002/95/EG)
Features:
»K-Band VCO Transceiver with advanced SiGe MMIC technology
»FSK / FMCW modes
»1/x divider for reference frequency output
»stereo (dual channel) opera! on to detect direc! on of mo! on
»integrated RF-pre-amplifi er
Product Family
Applica ons
K-Band VCO Transceiver with advanced MMIC technology
» Traffi c Monitoring
Movement
Velocity
Direc! on
Presence
Distance
Angle
CONFIDENTIAL AND PROPRIETARY
The informa! on contained in this document shall remain the sole and exclusive property of InnoSenT GmbH and shall
not be disclosed by the recipient to third par! es without prior consent of InnoSenT in wri! ng.
Descrip! on Cer! fi cates
InnoSenT sets standards – worldwide
Page 2 Version 1.0 DATA SHEET IVS-979
Oscillator
transmit frequencies f 24.000 - 24.250 GHz depending on Vtune
varactor tuning voltage Vtune 0 3 V
tuning bandwidth fi ne DC 500k Hz
tuning bandwidth coarse DC 0.4 Hz
input impedance Vtune fi ne 1 kΩ 200pf ESD protec# on
input impedance Vtune coarse 1 kΩ 200pf ESD protec# on
tuning slope coarse 340 552 766 MHz/V
tuning slope fi ne 59 96 133 MHz/V
temperature dri$ frequency Δf -4 -5 MHz/°C
ouput power (EIRP) Pou-ETSI 20 dBm @ room-temperature
out of band radia# on (EIRP) Pout of band -30 dBm @ room-temperature
divider ra# o factory se& ng 1,280 for example 24.200GHz
lead to 1.18MHz
Receiver
IF-amplifi er gain 40 dB part number LT6204
bandwidth 100 2.5M Hz
output impedance 100 Ω
signal level S I/Q t.b.d. mV @ InnoSenT Test setup
R I/Q t.b.d. mV @ InnoSenT Test setup
IF-output voltage off set 1.65 V
I/Q balance amplitude 6 dB
phase 70 95 120 °
Antenna pa! ern (compare with antenna pa! ern on page 4)
antenna pa* ern (@3dB) horizontal 7 ° azimuth
ver# cal 28 ° eleva# on
side lobe suppression horizontal 15 dB azimuth
ver# cal 15 dB eleva# on
Power Supply
supply voltage VCC 5.3 5.5 6 V max. 1mVPP ripple
supply current ICC 170 mA
Environment
opera# ng temperature TOP -30 +60 °C
storage temperature TSTG -30 +85 °C
outline dimensions 120 x 72.5 x 10.65 (17.7) mm compare drawing
Electrical Characteris" cs
Parameter Symbol Min. Typ. Max. Units Comment
CONFIDENTIAL AND PROPRIETARY
The informa# on contained in this document shall remain the sole and exclusive property of InnoSenT GmbH and shall
not be disclosed by the recipient to third par# es without prior consent of InnoSenT in wri# ng.
Handling Precau" ons
This InnoSenT sensor is sensi# ve to damage from ESD.
Normal precau# ons as usally applied to CMOS devices are suffi cient when handling this device.
Touching the signal output PINs has to be avoided at any # me before soldering or plugging the
device into a motherboard.
InnoSenT sets standards – worldwide
Page 3 Version 1.0 DATA SHEET IVS-979
Tx - antenna pa ern
1 MUXOUT OUT-digital reference signal VCO frequency already divided by prescaler
2 GND ground
3 VCC IN-analog 5.5V supply voltage
4 SPI_CLOCK IN-digital SPI-clock
5 SPI_DATA IN-digital SPI-data
6 PLL_LE IN-digital latch enable PLL
7 d.n.c. do not connect
8 CUST_PROG_LE IN-digital enable customer programming (ac! ve low)
9 d.n.c. IN-digital do not connect
10 d.n.c. do not connect
11 d.n.c. do not connect
12 Q-SIGNAL OUT-analog IF-output-signal
13 I-SIGNAL OUT-analog IF-output-signal
14 Vtune coarse IN-analog tuning voltage for coarse tuning VCO
15 Vtune fi ne IN-analog tuning voltage for fi ne tuning VCO
Pin # Descrip! on In / Out Comment
CONFIDENTIAL AND PROPRIETARY
The informa! on contained in this document shall remain the sole and exclusive property of InnoSenT GmbH and shall
not be disclosed by the recipient to third par! es without prior consent of InnoSenT in wri! ng.
Interface
full beam width @ -3dB horizontal 7 °
ver! cal 28 °
side-lobe suppression horizontal 15 dB
vertical 15 dB
Parameter Symbol Min. Typ. Max. Units Comment
output power [dBm]
angle [°]
The sensor provides a 2.54mm grid pin header.
-40
-35
-30
-25
-20
-15
-10
-5
0
-180,0 -150,0 -120,0 -90,0 -60,0 -30,0 0,0 30,0 60,0 90,0 120,0 150,0 180,0
InnoSenT sets standards – worldwide
Page 4 Version 1.0 DATA SHEET IVS-979
Mechanical Outlines
All dimensions in mm
Changes or modifi ca" ons made to the equipment not expressly approved by InnoSenT GmbH
may void the FCC / IC authoriza" on to operate this equipment.
The use of the transceiver module is authorized in mobile or fi xed host devices taking into account
the condi" ons listed below:
• OEM Integrator must ensure that the end user manual may not contain any informa" on
about the way to install or remove the module from the fi nal product.
• Depending on the fi nal host device addi" onal authoriza" on requirements for the non-
transmi# er func" ons of the transmi# er module may be required (i.e., Verifi ca" on, or Declara" on
of Conformity) The OEM integrator is responsible for ensuring that a$ er the module is installed and
opera" onal the host con" nues to be compliant with the Part 15B uninten" onal radiator require-
ments.
• The informa" on on the label and in the user manual is required to be incorporated in
the user manual of the fi nal host. see 47 CFR15 requirements for more details (e.g. 15.19 / 15.21 /
15.101 / 15.105 / RSS-GEN / ICES)
• Addi" onal label with the words ‘Contains FCC ID:AAABBBBB’ and ‘Contains IC:AAAA-BBBB’
shall be applied and visible from the outside of the host product.
• The module must be installed and used in strict accordance with the manufacturer’s inst-
ruc" ons as described in the user documenta" on that comes with the module.
• The end user manual for the fi nal host product opera" ng with this transmi# er must inclu-
de opera" ng instruc" ons to sa" sfy RF exposure compliance requirements. e.g
InnoSenT sets standards – worldwide
Page 5 Version 1.0 DATA SHEET IVS-979
Contact Informa on
InnoSenT GmbH | Am Roedertor 30 | 97499 Donnersdorf | Germany
Phone: +49 (0) 9528-9518-0 | Fax: +49 (0) 9528-9518-99 | E-Mail: info@innosent.de
www.innosent.de
InnoSenT GmbH
Am Rödertor 30
97499 Donnersdorf
GERMANY
Approval
This Data Sheet contains the technical specifi ca" ons of the described product. Changes of the
specifi ca" on must be in wri# en form. All previous versions of this Data Sheet are no longer valid.
The technical specifi ca" ons of this Data Sheet are approved by:
Radiofrequency radia" on exposure Informa" on:
This equipment complies with FCC radia" on exposure limits set forth for an uncontrolled environ-
ment. This equipment should be installed and operated with minimum distance of 20 cm between
the radiator and your body.
This transmi# er must not be co-located or opera" ng in conjunc" on with any other antenna or
transmi# er.
• When the fi nal host product opera" ng with this transmi# er deviate from above, installa" -
on of this module into specifi c fi nal hosts may require the submission of a Class II permissive change
applica" on containing data per" nent to RF Exposure, spurious emissions, ERP/EIRP, and host/modu-
le authen" ca" on, or new applica" on if appropriate.
Feel free to contact us if addi" onal guidance is required.
Manual Requirements according 15.19 / RSS-GEN
This device complies with Part 15 of the FCC Rules [and with Industry Canada licence-exempt RSS
standard(s)].
Opera" on is subject to the following two condi" ons:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired opera" on.
Manual Requirements according 15.21
Changes or modifi ca" ons made to this equipment not expressly approved by (manufacturer name)
may void the FCC authoriza" on to operate this equipment.