Inovonics Wireless 3B6AVBST ANALOG VOICE BASE STATION User Manual User Instructions

Inovonics Wireless Corporation ANALOG VOICE BASE STATION User Instructions

Install Lit

1 QSR Performance Solutions Drive Thru System - Operating Instructions Batteries and Battery Charger • Be sure batteries are charged • Batteries take 2 to 3 hours to charge • A charge battery will last 8 to 10 hours • When the battery voltage becomes too low, a short warble tone, occurring at five–second intervals is heard in the headset. After 2 minutes the headset will shut off. • Batteries only fit into charge one way, the correct way • Charging indicator on charger will light red while battery is charging • Charging indicator on charger will change from red to green when battery is fully charge • Batteries should be left in charger even after they are fully charged • Batteries should be removed from belt-pack and stored in charger when belt-pack is not being used • Batteries not being used should stored in the charger Charging Indicators Charging Ports for Batteries Battery Charger Installing and Removing Batteries from Belt-Pack • Insert battery into battery compartment on belt-pack so it locks into place • Battery will only fully insert into battery compartment the correct way • To remove battery, slide battery release away from battery Battery Compartment Battery Release
2 QSR Performance Solutions Drive Thru System - Operating Instructions Connecting Headset to Belt-Pack • The 2 prong headset connector plugs into the bottom of the belt-pack Headset Jack Programming the Belt-Packs • Belt-packs must me programmed to the base station before they will operate properly • Programming station should already be plugged into base station • Make sure power indicator on base station is lit • Insert battery in belt-pack • Make sure belt-pack power is turned OFF • Insert belt-pack into programming station • Turn belt-pack power ON • Power indicator on belt-pack will flash green during programming (about 5 seconds) Programming Station Belt-Pack in Programming Station
3 QSR Performance Solutions Drive Thru System - Operating Instructions Taking Orders • Belt-pack should be in pouch and clipped to belt or waist-band on pants • Headset cable should be clipped near waist and near collar • Headset should be worn on head • The headband is adjustable • Make sure power indicator on belt-pack is lit green • When a car arrives at the menu-board, fast double beep will be heard every 3 seconds • Press the talk button on the belt-pack to talk to the customer For information on all of the features of the belt-pack, see the last page of these instructions. QSR Performance Solutions Drive Thru System - Base Station Front Cover Indicators & Controls Channel Indicators Page Indicator Talk Indicator Power Switch Used to turn power to Power Indicator Lights when Day / Night Volume Switch Grill Monitor Vehicle Indica-
4 QSR Performance Solutions Drive Thru - Belt-Pack 1 2 3 4 5 6 7 8 9 10 11 Bottom View 7. Talk 2 • Has the exact same function as Talk 1 when used with a single lane system • On Dual and Cross Lane systems Talk 2 will be programmed to communicate with Lane 2 8. Talk 1 • Activates communication to outside speaker • Will also be heard by other headsets and possibly grill speaker (depending on system configuration) • Can be used to test incoming and outgoing audio even when no car is present • On half-duplex systems, press to talk and release to listen • On full-duplex systems incoming audio will be heard even while Talk 1 is pressed • On Dual and Cross Lane systems Talk 1 will be programmed to communicate with Lane 1 9. Headset Jack • The 2 prong headset connector plugs in here 10. Battery Compartment • Battery goes here 11. Battery Release • Slide back to release battery from compartment 1. Page • Press to talk to the other headsets without being heard at the speaker post • Belt-packs can be programmed for Page Monitor Mode, they will only hear communication from other belt-packs that are using the Page button and will not hear communication to or from the speaker post • To program a belt-pack for Page Monitor Mode, hold Page button down while powering the headset on. • To exit Page Monitor Mode turn the belt-pack off and back on 2. Volume Down • Listening volume can be adjusted in 7 steps from the lowest to high-est setting. When the belt-pack is powered on, the listening level will be near mid-level and can be adjusted 3 steps up or 4 steps down. A short tone will be heard each time the volume is adjusted. A long tone is heard when the lowest or highest level is reached. 3. Volume Up • Turns up incoming audio from speaker post. See previous section for details 4. Power LED • Green when belt-pack is powered on • Red when talk-lock is in use • Flashes green during channel programming 5. Power On / Off • Press to turn power to belt-pack on or off 6. Talk Lock • Used with a full-duplex system, press to activate hands-free com-munication • When car arrives at speaker post, press to activate. Communication will automatically deactivate when car leaves speaker post and automatically reactivate when next car arrives • Press Talk 1 or Page to deactivate Talk Lock • Only 1 belt-pack at a time can use Talk Lock and no other headsets can talk to the speaker post • Disabled or enabled by holding Talk Lock button down when the headset is being powered up

Navigation menu