Inovonics Wireless 3B6AVBST ANALOG VOICE BASE STATION User Manual User Instructions

Download:
Mirror Download [FCC.gov]
Document ID	1336435
Application ID	drRa58ssV3UMYRZq9xDc+Q==
Document Description	Install Lit
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	158.29kB (1978569 bits)
Date Submitted	2010-09-01 00:00:00
Date Available	2010-10-08 00:00:00
Creation Date	2010-06-18 10:21:26
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2010-06-18 10:21:26
Document Title	User Instructions
Document Creator	PScript5.dll Version 5.2.2
Document Author:	JohnJelinek

QSR Performance Solutions Drive Thru System - Operating Instructions
Batteries and Battery Charger
•
•
•
•
•
•
•
•
•
•
Be sure batteries are charged
Batteries take 2 to 3 hours to charge
A charge battery will last 8 to 10 hours
When the battery voltage becomes too low, a short warble tone, occurring at five–second intervals is heard in the
headset. After 2 minutes the headset will shut off.
Batteries only fit into charge one way, the correct way
Charging indicator on charger will light red while battery is charging
Charging indicator on charger will change from red to green when battery is fully charge
Batteries should be left in charger even after they are fully charged
Batteries should be removed from belt-pack and stored in charger when belt-pack is not being used
Batteries not being used should stored in the charger
Charging Indicators
Charging Ports for
Batteries
Battery Charger
Installing and Removing Batteries from Belt-Pack
•
•
•
Insert battery into battery compartment on belt-pack so it locks into place
Battery will only fully insert into battery compartment the correct way
To remove battery, slide battery release away from battery
Battery
Compartment
Battery
Release
QSR Performance Solutions Drive Thru System - Operating Instructions
Programming the Belt-Packs
•
•
•
•
•
•
•
•
Belt-packs must me programmed to the base station before they will operate properly
Programming station should already be plugged into base station
Make sure power indicator on base station is lit
Insert battery in belt-pack
Make sure belt-pack power is turned OFF
Insert belt-pack into programming station
Turn belt-pack power ON
Power indicator on belt-pack will flash green during programming (about 5 seconds)
Programming Station
Belt-Pack in Programming Station
Connecting Headset to Belt-Pack
•
The 2 prong headset connector plugs into the bottom of the belt-pack
Headset
Jack
QSR Performance Solutions Drive Thru System - Operating Instructions
Taking Orders
•
•
•
•
•
•
•
Belt-pack should be in pouch and clipped to belt or waist-band on pants
Headset cable should be clipped near waist and near collar
Headset should be worn on head
The headband is adjustable
Make sure power indicator on belt-pack is lit green
When a car arrives at the menu-board, fast double beep will be heard every 3 seconds
Press the talk button on the belt-pack to talk to the customer
For information on all of the features of the belt-pack, see the last page of these instructions.
QSR Performance Solutions Drive Thru System - Base Station Front Cover Indicators & Controls
Channel Indicators
Power Switch
Used to turn power to
Talk Indicator
Page Indicator
Power Indicator
Lights when
Day / Night Volume
Switch
Vehicle Indica-
Grill Monitor
QSR Performance Solutions Drive Thru - Belt-Pack
10
11
Bottom View
1. Page
Press to talk to the other headsets without being heard at the
speaker post
• Belt-packs can be programmed for Page Monitor Mode, they will
only hear communication from other belt-packs that are using the
Page button and will not hear communication to or from the speaker
post
• To program a belt-pack for Page Monitor Mode, hold Page button
down while powering the headset on.
• To exit Page Monitor Mode turn the belt-pack off and back on
7. Talk 2
• Has the exact same function as Talk 1 when used with a single lane
system
• On Dual and Cross Lane systems Talk 2 will be programmed to
communicate with Lane 2
•
8. Talk 1
Activates communication to outside speaker
•
•
•
2. Volume Down
• Listening volume can be adjusted in 7 steps from the lowest to highest setting. When the belt-pack is powered on, the listening level will
be near mid-level and can be adjusted 3 steps up or 4 steps down.
A short tone will be heard each time the volume is adjusted. A long
tone is heard when the lowest or highest level is reached.
•
•
•
3. Volume Up
Turns up incoming audio from speaker post. See previous section
for details
•
4. Power LED
Green when belt-pack is powered on
•
•
•
•
•
10. Battery Compartment
Battery goes here
Red when talk-lock is in use
11. Battery Release
Slide back to release battery from compartment
Flashes green during channel programming
•
6. Talk Lock
Used with a full-duplex system, press to activate hands-free communication
• When car arrives at speaker post, press to activate. Communication
will automatically deactivate when car leaves speaker post and
automatically reactivate when next car arrives
• Press Talk 1 or Page to deactivate Talk Lock
•
•
On full-duplex systems incoming audio will be heard even while Talk
1 is pressed
On Dual and Cross Lane systems Talk 1 will be programmed to
communicate with Lane 1
9. Headset Jack
The 2 prong headset connector plugs in here
5. Power On / Off
• Press to turn power to belt-pack on or off
•
Will also be heard by other headsets and possibly grill speaker
(depending on system configuration)
Can be used to test incoming and outgoing audio even when no car
is present
On half-duplex systems, press to talk and release to listen
Only 1 belt-pack at a time can use Talk Lock and no other headsets
can talk to the speaker post
Disabled or enabled by holding Talk Lock button down when the
headset is being powered up

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2010:06:18 10:21:26-05:00
Create Date                     : 2010:06:18 10:21:26-05:00
Format                          : application/pdf
Title                           : User Instructions
Creator                         : JohnJelinek
Document ID                     : uuid:1f5b79ee-de1d-45f4-9558-981680ac27fc
Instance ID                     : uuid:cce73337-d25c-40df-b438-52e974e0c45a
Page Count                      : 4
Author                          : JohnJelinek

EXIF Metadata provided by EXIF.tools