Intech Electronics CS8124 Bluetooth Headset User Manual MCB 8088010 1B USER MANU

Download:
Mirror Download [FCC.gov]
Document ID	842476
Application ID	vqylQXVYtm9SIX8vaC50Vg==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	80.84kB (1010505 bits)
Date Submitted	2007-09-13 00:00:00
Date Available	2007-09-13 00:00:00
Creation Date	2007-09-12 15:36:25
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2007-09-12 19:37:29
Document Title	MCB-8088010-1B ( # USER MANU...
Document Creator	PScript5.dll Version 5.2
Document Author:	jonathancao

Bluetooth ® Headset
BT 28VM
Putting Headset in Pairing Mode
Make sure the HS is fully powered before pairing starts. While the HS is powered off,
press and hold S1 for 10 seconds. Red and Orange LED is flashing alternately
indicating that the HS is in Pairing Mode.
Follow the operating instructions for your Bluetooth mobile phone to start the pairing
process. Typically, this has to be done by going to a setup or connect menu and then
selecting the options to discover Bluetooth devices. Bluetooth may take several
seconds to establish a connection.
Your phone ' s display should indicate that it has found the“ B T 28VM ”headset and
asks if you want to pair it. You should confirm this. The phone ' s display would prompt
you for a passkey or PIN. Enter a sequence of “0000 ”.
The headset LED will flash Orange every 3 seconds, indicating successful pairing.
Usually the phone will also ask whether you want to change the headset ' s name. We
recommend you should approve the BT 28VM name and not change it. You can pair
as many headsets and devices as you wish in your mobile phone.
If pairing does not occur as expected. Turn the headset and phone off and wait for 10
seconds. Turn the headset and phone on again and repeat all steps from beginning.
Establishing Bluetooth Link
After pairing, the mobile phone will show “ connect ”, then please select “ YES ”to
establish the link . Now you are ready to make and answer calls on the HS . For other
phones , please follow the operation manual to establish the link .
User Manual
Answering Incoming Calls
When an incoming call is present, the HS will ring . Pressing S1 will answer the call.
The orange LED will continue to flash quickly while the call is in session.
Index
Headset pictures
.............................................................................2
Installation of battery .......................................................................2
Turning on the Headset
.......................................................................2
Turning off the Headset
......................................................................2
Putting Headset in Pairing Mode
Establishing Bluetooth Link
Answering incoming calls
..............................................................3
..................................................................3
Ending calls
To transfer a call to or from the Bluetooth phone: double press S1, the call will be
transferred to or from the Bluetooth phone, or follow the operating instructions of your
phone.
.....................................................................4
Tr a n s f e r r i n g c a l l s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Muting the microphone
Transferring Calls (For Nokia 3650 or equivalent models)
When you are in session, calls can be transferred from the Bluetooth phone to the HS
and from the HS to the Bluetooth phone.
........................................................................4
Muting the microphone
To mute the microphone during an active call
.................................................................................4
To make a new call using voice dialing
Redialing last dialed number
Rejecting incoming call
......................................................................5
Adjusting speaker volume
Ear Hook orientation
.....................................................................5
.........................................................................6
Bend the ear hook to fit your ear
Putting way
.......................................................5
.................................................................5
.......................................................................7
Voice Over Internet Protocol (VOIP) Application
FCC Interference Statement
Declaration of Conformity
Ending Calls
While a call is in session on the Headset, pressing S1 will disconnect the call. After the
call is disconnected, the orange LED will flash normally.
.............................................8
..................................................................11
Volume Down( S3)
Ear hook
Speaker
Volume Up (S2)
When the microphone is muted, press on both S2 and S3 buttons simultaneously will
end the mute function and the periodic beep tone will stop.
..................................................................9
On/ Off( S1)
To end the mute function
............................................................6
.................................................................................7
Low-battery indication
Pressing both S2 and S3 buttons simultaneously for about a second, the microphone
will be muted. A periodic beep tone will be heard while the mute function is active.
LED
Lock
Microphone
Installation of battery
Thank you for buying new BT 28VM Bluetooth Headset.
Before use please open the battery door and install the battery (AAAx1) into the
battery compartment according to the correct polarity. Close the battery door.
To make a new call using voice dialing
When using a Bluetooth mobile phone:
1.Make sure the voice dialing function is probably set up in the Mobile phone and it is
within the range of the HS. Press S1 on the HS shortly.
2.After the beep tone on the HS, make a voice dialing as you normally would by
saying the name of the person on the HS. The call will be
connected in a few
seconds.
When using a mobile phone without Bluetooth built-in and requiring a Bluetooth dongle:
1. Make sure the voice dialing function is probably set up in the mobile phone and it is
within the range of the HS. Press S1 on the HS shortly.
2. After the beep tone on the mobile phone, make a voice dial as you normally would
and the call will be connected in a few seconds.
Redialing last dialed number (Support handsfree profile mobile only. For Nokia
3650, Siemens S55, or equivalent models)
To redial the last dialed number, press and hold S3 for 2 seconds, a short low tones
will indicate an attempt to redial.
Turning on the Headset
While the Headset (HS) is powered down, press and hold S1 for approx 10 seconds
until you hear a low tone followed by a high tone. The orange LED will turn on for 1
second then flashes.
Turning off the Headset
While the HS is powered up, press and hold S1 until you hear a high tone followed by
a low tone indicating that the HS is powered down. And the LED will keep on Red
until S1 is released.
Rejecting incoming call (Support handsfree profile mobile only. For Nokia 3650,
Siemens S55, or equivalent models)
When there is an incoming call and you want to reject it, press the buttons S1 and hold
it until you hear a long beep tone, then release it.
Adjusting Speaker Volume
While a call is in session , pressing and releasing S2 will increase the speaker
volume; pressing and releasing S3 will decrease the speaker volume on the HS .
There is a key tone to indicate volume increase or decrease .
However , a
warning tone will be heard when the volume level reaches its maximum or
minimum .
Ear Hook orientation
If you want to change the orientation of ear hook, please follow the following steps.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
1) Detach the ear hook from the headset
2) Select the orientation you want (left or right), and attach the ear hook and lock it
Bend the ear hook to fit your ear
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
the
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Putting way
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
1. Put on the headset with the ear hook behind your ear.
2. Bend the ear hook gently to fit your ear.
Notice: Make sure the microphone is pointing towards your mouth.
Low-battery indication
The HS LED will flash red instead of orange when the battery is low.
There will also be a short beep every few minutes. When the battery level is too low ,
the HS will automatically power off.
DISCLAIMER: Talk time and stand-by time of the BT 28VM Bluetooth Headset will vary depending on
mobile phone model being used
10
UB 22S USB Bluetooth Dongle and BT 28VM Bluetooth Headset
Voice Over Internet Protocol (VOIP) Application
1. Plug the UB 22S USB Bluetooth Dongle (purchased separately) into the USB socket of
a PC.
2. Install IVT BlueSoleil Bluetooth application from the CD-ROM provided in the UB 22S
package. Note that the CD-ROM is not available in the BT 28VM package.
3. Download from the corresponding websites and install MSN messenger, Netmeeting,
Yahoo messenger, or ICQ application software in the PC.
Pairing: Put the BT 28VM Bluetooth Headset into "pairing" mode by following the
steps in the BT 28VM User Manual, start the BlueSoleil application and pair the UB
22S Dongle with the BT 28VM Headset. The Headset passkey is "0000 ".
4. Connecting and Disconnecting: The UB 22S Dongle will ring the BT 28VM Headset.
Please press the S1 key on the headset to confirm the connection request. To
disconnect the Bluetooth link, press the S1 key again. You can now pair and
reconnect your BT 28VM Headset to your Bluetooth mobile phone, if you desire.
5. Testing the Bluetooth Link: After the UB 22S Dongle is paired with the BT 28VM
Headset, the PC audio will be automatically routed to the " Bluetooth Audio"driver.
Play some music on the PC by Windows Media Player or other music applications; you
should be able to hear the music on the Headset. If you can't hear it, then go the
"control Panel"-> "Sound and Audio Device Properties"-> "Audio"-> "Sound playback"
select the " Bluetooth Audio"to activate the link.
6. Now you can start using the VOIP application and talk to your friend through your
headset wirelessly and freely.
Connecting BT 28VM Bluetooth Headset back to your Bluetooth mobile phone. Please
follow the steps from 'Putting Headset in Pairing Mode' to ' Establishing Bluetooth Link' on
page 7.
11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-701
About                           : uuid:55dca27d-f652-4c0e-afe0-de6306e45ae2
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2007:09:12 15:36:25+08:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2007:09:12 19:37:29+08:00
Metadata Date                   : 2007:09:12 19:37:29+08:00
Document ID                     : uuid:98b905a9-a819-4d56-9cfc-2fd0508e709e
Instance ID                     : uuid:2b5221c2-3754-443b-bcf9-eed6e873b6de
Format                          : application/pdf
Title                           : MCB-8088010-1B  ( # USER MANU...
Creator                         : jonathancao
Page Count                      : 2
Author                          : jonathancao

EXIF Metadata provided by EXIF.tools