Intel 7262W2 WWAN Module Adapter Card User Manual Intel 7262M2WW UserGuide V1 2

Download:
Mirror Download [FCC.gov]
Document ID	2698346
Application ID	GjJkNYxvV8K6jqy2jMLKYQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	219.29kB (2741133 bits)
Date Submitted	2015-07-30 00:00:00
Date Available	2016-01-26 00:00:00
Creation Date	2015-07-25 09:46:34
Producing Software	Acrobat Distiller 15.0 (Windows)
Document Lastmod	2015-07-25 09:46:34
Document Title	Microsoft Word - Intel_7262M2WW_UserGuide_V1 2
Document Creator	PScript5.dll Version 5.2.2
Document Author:	schacket

Intel Model 7260M2NA and
7262M2WW
User Guide
Revision 1.2, Feb 2015
Document Number: N/A
Revision History
Revision History
Revision Number
Description
Revision Date
1.0
Initial version of the document
17‐Dec‐2012
1.1
Revise to add model 7260M2NA
Nov 2014
1,2
Revise to add model 7262M2WW
Feb 2015
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
2/44
Revision History
Contents
Introduction............................................................................................................................................ 6
Software Framework .......................................................................................................................... 8
2.1
2.1.1
Driver Installation ................................................................................................................................ 8
General Considerations...................................................................................................................... 8
2.1.2
Intel High Speed Modem Driver (ecm200) ................................................................................ 9
2.1.2.1
Client offset configuration. ............................................................................................................. 13
2.1.2.2
Static IP Address Configuration.................................................................................................... 15
2.1.3
Comneon High Speed Modem Driver ......................................................................................... 18
2.1.4
Flash USB driver and FTDI Driver ............................................................................................... 20
2.1.5
Prolific Serial to USB Driver ........................................................................................................... 20
2.2
2.3
2.3.1
LTE debug UART configuration ..................................................................................................... 21
System Trace Box .............................................................................................................................. 23
Setup and Configuration ................................................................................................................. 23
2.3.1.1
Entering AT Commands ................................................................................................................... 23
2.3.1.2
Board Configuration and required AT Commands ................................................................. 23
2.3.2
Connecting the UE ............................................................................................................................. 24
2.4
AT Commands Examples ................................................................................................................ 24
Test Cases ............................................................................................................................................ 28
3.1
3.1.1
Protocol Test (CMW500) ................................................................................................................. 28
CWM 500 Firmware ........................................................................................................................... 28
3.1.2
Test Scenario ....................................................................................................................................... 29
3.1.3
AT Commands ..................................................................................................................................... 30
3.1.4
The Data Application Unit ............................................................................................................... 30
Regulatory Notice .............................................................................................................................. 33
Abbreviations / Terminology ......................................................................................................... 34
Appendix A Definitions/Explanations.................................................................................................................. 36
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
3/44
Revision History
Figures
Figure 1. Location of the Prolific serial to USB driver, the Flash USB driver and the
FTDI diver within the flash tool folder. ................................................................................ 8
Figure 2. Use the already installed driver. ............................................................................... 10
Figure 3. Install the driver again. ................................................................................................ 10
Figure 4. The network modem and four COM ports are now appearing at the
device manager. ......................................................................................................................... 11
Figure 5. Open the network connections dialog. Win XP :
Start:Settings:NetworkConnectios. A new network device did pop up. It is not
yet connected. ............................................................................................................................. 12
Figure 6. On Win7: Select “Start:Control Panel:Network and Sharing Center”
followed by “Change adapter settings”. ........................................................................... 12
Figure 7. Open the properties dialog of the new network device (right click). ......... 12
Figure 8. Select the configuration dialog. ................................................................................ 13
Figure 9. Set the client offset to 1 and press “OK”. ............................................................. 14
Figure 10. Press “OK” to save these settings. Otherwise these settings get lost. ... 14
Figure 11. Open the Internet Protocol TCP/IP settings. ..................................................... 16
Figure 12. Set the static Network IP and press OK. ............................................................ 17
Figure 13. To close the properties dialog and save the settings press “OK”. ............ 17
Figure 14. Congratulations. Your ecm200 driver and its IP connection are now
properly configured. .................................................................................................................. 18
Figure 15. Use the already installed driver. ............................................................................ 19
Figure 16. Install the driver. ......................................................................................................... 19
Figure 17. Comneon suspend and six COM ports are now appearing at the device
manager......................................................................................................................................... 20
Figure 18. USIF1 Device Manager Prolific USB-to-Serial COM Port ............................... 21
Figure 19. Putty configuration. ..................................................................................................... 22
Figure 20. CMW 500 ......................................................................................................................... 28
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
4/44
Revision History
Tables
Table 1. Terminal Port Settings .................................................................................................... 22
Table 2. AT Commands trace box support. ................................ Error! Bookmark not defined.
Table 3. Terminal Port Settings .................................................................................................... 25
Table 4. AT Commands to check ARM software version..................................................... 25
Table 5. AT Commands to Register on the Network ............................................................ 25
Table 6. AT Commands for an Incoming Call ......................................................................... 25
Table 7. AT Commands for an Outgoing Call .......................................................................... 26
Table 8. AT Commands for SMS Management ....................................................................... 26
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
5/44
Revision History
Introduction
This document provides a brief description of the NGFF Carrier Board development kit. Including:
Hardware interfaces with FIH board
NGFF Carrier Board User Guide V2.0
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
6/44
Revision History
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
7/44
Revision History
Software Framework
2.1
Driver Installation
2.1.1
General Considerations
The two different test and debug configurations always require a Win PC where up to five different
drivers must be installed accurately.
This are:
1. the Intel High Speed Modem Driver (ecm200),
2. the Comneon High Speed Modem Driver,
3. the Prolific serial to USB driver (part of the flash tool folder),
4. the Flash USB driver (part of the flash tool folder) and
5. the FTDI diver.
Figure 1. Location of the Prolific serial to USB driver, the Flash USB driver and the FTDI diver
within the flash tool folder.
Pls note that Win does not always complain if the drivers 4 to 5 are not installed. If one of these
drivers is missing flashing problems are occurring.
The ARM software and LTE firmware releases are linked to individual driver revision numbers that
were used for release testing. They were typically published together with the ARM software and the
LTE firmware here:
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
8/44
Revision History
http://wiki.imu.imc.local/XG716_LTE_CV_Setup_versions
The latest drivers can be found here:
\\musdsara001.imu.imc.local\SW_builds\xmm6360\tools
Or if something is missing here:
\\musdsara001.imu.imc.local\SW_builds\xmm7060\Release\Tools
Which is similar to
M:\Software\XMM7060_tools at IMC DRS
Flash Tool :
\\musdsara001.imu.imc.local\SW_builds\xmm6360\tools\flashtool
Socmondll :
\\musdsara001.imu.imc.local\SW_builds\xmm7060\Release\Tools\Socmondll\socmondll_1
00.150.001.dll
2.1.2
Intel High Speed Modem Driver (ecm200)

Take the recommended driver, see Subsec. 2.1.1, (folder e.g. WMC_ecm200_3.61.0)
and follow the instructions from the installation wizard.

Enable the IP forwarding: run the sriptenable_ip_forwarding.reg from:
\\musdsara001.imu.imc.local\SW_builds\xmm7060\Release\Tools\Intel_High_Speed_Mod
em
Hint: Copy the file to the local PC and then run it with root privileges.
Now connect the cable to the USB‐HS connector.
Win XP asks now it’s typical questions and gets the common answers see below. Win 7 does not ask
and loads the driver automatically.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
9/44
Revision History
Figure 2. Use the already installed driver.
Figure 3. Install the driver again.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
10/44
Revision History
Figure 4. The network modem and four COM ports are now appearing at the device manager.

Now open the network manager and configure the network settings of the modem.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
11/44
Revision History
Figure 5. Open the network connections dialog. Win XP : Start:Settings:NetworkConnectios. A
new network device did pop up. It is not yet connected.
Figure 6. On Win7: Select “Start:Control Panel:Network and Sharing Center” followed by
“Change adapter settings”.
Figure 7. Open the properties dialog of the new network device (right click).
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
12/44
Revision History
2.1.2.1
Client offset configuration.
This must be done before the IP settings. If the order is flipped the IP settings get lost.
Figure 8. Select the configuration dialog.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
13/44
Revision History
Figure 9. Set the client offset to 1 and press “OK”.
Figure 10. Press “OK” to save these settings. Otherwise these settings get lost.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
14/44
Revision History
2.1.2.2
Static IP Address Configuration

The given example IP number at Figure 12 is for a simplified test and debug setup,
see Error! Reference source not found., where the octave or java client runs on the
Win PC that also carries all necessary Win drivers and is connected to the DUT. The
ecm200 driver runs in a subnet that is only visible from this PC.

The complete setup, see Error! Reference source not found., consists of test PCs
that were provided together with recommended IP settings for the ecm200 driver.
The static route settings were set typically IT system wide.

In case two PCs were used to run the tests, a test PC with the drivers and a desktop
PC that carries the Octave or the Java client a static route must be set at the desktop
PC. The example below helps to find proper static route settings:
test PC with static IP: 10.1.0.126
ecm200 client at test PC with IP: 172.16.126.1 (client offset set to 1)
run as root at the PC where the Octave is running on.
route print #read out route settings
route add 172.16.126.0 mask 255.255.255.0 10.1.0.126
 test the configuration:
ping 172.16.126.1 #response from the ecm200 driver
ping 172.16.126.2 #response from the booted LTE‐IP block (L1CC)

Reopen the Network Connection Properties Dialog.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
15/44
Revision History
Figure 11. Open the Internet Protocol TCP/IP settings.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
16/44
Revision History
Figure 12. Set the static Network IP and press OK.
Figure 13. To close the properties dialog and save the settings press “OK”.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
17/44
Revision History
Figure 14. Congratulations. Your ecm200 driver and its IP connection are now properly
configured.

2.1.3
If desired it is now also possible to rename the network device from “Wireless
Connection2” to something more convenient e.g. ecm200 + IP address.
Comneon High Speed Modem Driver

Take the recommended driver,

\\musdsara001.imu.imc.local\SW_builds\xmm6360\tools\usb_drive
rs
See also SMS02534274: ‐ Please use 3.46 version and not
WMC_comneon2_3.55.0, see Subsec. 2.1.1, (folder
Comneon_High_Speed_Modem_Driver) and follow the instructions from the
installation wizard.

Now connect the cable to the USB-HS connector.

Win XP asks now it’s typical questions again and gets the common answers, see
below. Win 7 does not ask and loads the driver automatically.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
18/44
Revision History
Figure 15. Use the already installed driver.
Figure 16. Install the driver.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
19/44
Revision History
Figure 17. Comneon suspend and six COM ports are now appearing at the device manager.

2.1.4
Congratulations, your driver installation has finished successfully.
Flash USB driver and FTDI Driver
These drivers are mandatory to flash new ARM software and LTE firmware images at the modem
board. Take the recommended drivers, see Subsec. 2.1.1, (flash tool subfolder) and follow the
instructions from the installation wizards.
Note:
2.1.5
If this drivers are not installed correctly instabilities at the flash process are occurring
without substantial error information from Win XP or Win 7.
Prolific Serial to USB Driver
The Prolific driver is mandatory to access all modem board UART (USIF) ports. Take the recommended
driver, see Subsec. 2.1.1, (folder Prolific Driver) and follow the instructions from the installation
wizard.
Connect the USB cable to the desired USIF port and check that the COM port appears correctly in the
Win device manager. (Win:Settings:Control Panel:System Properties:Hardware:Device Manager. This is
quite similar to find at Win XP and Win 7.)
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
20/44
Revision History
Figure 18. USIF1 Device Manager Prolific USB‐to‐Serial COM Port
2.2
LTE debug UART configuration
After the preliminary setting, run any AT terminal application (e.g. HyperTerminal) on your PC’s
communication port, with the following settings.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
21/44
Revision History
Table 1. Terminal Port Settings
Data rate
115200 bps
Data Bits
Parity
Stop Bits
Flow Control
HW

on UNIX xterm use this with uucp:
%docing station serial port, uucp
chown uucp /dev/ttyUSB0
cu -l /dev/ttyUSB0 -s 115200

If putty http://www.putty.org is used this looks like this:
Figure 19. Putty configuration.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
22/44
Revision History
2.3
System Trace Box
2.3.1
Setup and Configuration
2.3.1.1
Entering AT Commands
The AT commands mentioned below must be sent to the COM port that corresponds to the

Intel Mobile (USB3) COM port in case the ecm 200 driver is used or

to the COM port that corresponds to the Comneon High Speed Modem, see Error!
Reference source not found..
The COM port that corresponds to the USIF‐1 USB port, see Error! Reference source not found. may
also work.
The udp2AT server can be used to enter local AT commands from remote locations, see Subsec. Error!
Reference source not found..
Board Configuration and required AT Commands
2.3.1.2

Reset the board in a way that is booting from the flash

Enable tracing using: at+xsystrace=0,"lte_l1_sw=4"

Reset the board again in a way that is booting from the flash

Now the initialization at commands to switch to Service Mode (that is the mode to
use RCTTH) can be sent if needed:
 ARM for Inc2.8: ‘at@ecal:’ ’at@ecal_init():’
 ARM for Inc3.0: ‘at@ephy:smon()’

Note: Please check with the provider of the ARM image which commands are valid
for the actual build!!!

The AT commands below are mandatory to enable tracing:
a. Enable tracing at all sources: at+trace=1;
b. Route traces through UE's "OCT‐Block", which creates the ISTP format:
at+xsio=3;
c. Select the traces from specific sources, use at+xystrace command. For example,
to configure the traces from specific to select ONLY the 3g_sw traces:
at+xsystrace=0,"3g_sw=1",,"oct=4"
d. make sure your SIM is not waiting for entering a PIN: at+cpin? If it is, send the
PIN at at+cpin=
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
23/44
Revision History
e. make sure, the 3G protocol stack is sending traces: at+cops=0; (this command
triggers the phone to (re‐)register to the network)
2.3.2
Connecting the UE
6. Connect the UE to the PC as described in section Error! Reference source not
found..
7. Find the com‐port in which UE is connected using comtest tool. Run the command
comtest –l. It will list the ports. Carefully evaluate the port for tracing and port for
control.
8. To check whether PC is connected to UE properly, try connecting the control port
with the terminal emulator and send “AT” command, If the response is OK, UE is
connected successfully. This can be done via AT Console in SystemTraceTool.
9. Send the below AT commands:
a. Enable tracing at all sources: at+trace=1;
b. Route traces through UE's "OCT‐Block", which creates the ISTP format:
at+xsio=3;
c. Select the traces from specific sources, use at+xystrace command. For example,
to configure the traces from specific to select ONLY the 3g_sw traces:
at+xsystrace=0,"3g_sw=1",,"oct=4"
d. make sure your SIM is not waiting for entering a PIN: at+cpin? If it is, send the
PIN at at+cpin=
e. make sure, the 3G protocol stack is sending traces: at+cops=0; (this command
triggers the phone to (re‐)register to the network)
2.4
AT Commands Examples
After the preliminary setting, run any AT terminal application (e.g. HyperTerminal) on your PC’s
communication port, with the following settings
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
24/44
Revision History
Table 3. Terminal Port Settings
Data rate
115200 bps
Data Bits
Parity
Stop Bits
Flow Control
HW
AT Command to check ARM Software version
Table 4. AT Commands to check ARM software version
Command sent by DTE
Response of DCE
Description
at+xgendata
The device will reply with the running ARM
software version
Register on the network (GSM/UMTS)
Table 5. AT Commands to Register on the Network
Command sent by DTE
Response of DCE
Description
AT+XRAT=1,2
select radio access technology: 1=GSM/UMTS Dual
mode; 2=UMTS
OK
AT+COPS=0
Register the phone on the network
OK
AT+CREG?
Verify registration
+CREG: 0, 1
OK
AT+COPS?
+COPS: 0,0,"AT&T",0
Read operator name
Incoming Voice Call
Table 6. AT Commands for an Incoming Call
Command sent by DTE
DCE Response
Description
ATA
OK
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
25/44
Revision History
Outgoing Voice Call
Table 7. AT Commands for an Outgoing Call
Command sent by DTE
DCE Response
Description
AT
OK
AT+CLIP=1
Activation of Caller line ID
presentation
OK
ATD+862161019000;
Outgoing voice call
OK
Voice call is accept from network
ATH
Hang up
OK
SMS Management
Table 8. AT Commands for SMS Management
Command sent by DTE
DCE Response
Description
AT+CMGF=1
OK
Set the text mode as the format that will be
used. To be set before of the first operation
AT+CMGF=0
OK
Set the PDU mode as the format that will be
used. To be set before of the first operation
AT+CMGS=”0171112233”
CMGS: [,]
“This is the text”
if PDU mode (+CMGF=0):
CMGS: [,]
+CMGS=PDU is
given
OK
or
CMS ERROR: 
Test command
OK
AT+CMGS=?
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
26/44
Revision History
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
27/44
Revision History
Test Cases
3.1
Protocol Test (CMW500)
Figure 20. CMW 500
In general it needs to be checked that CMW500 setup are identically to the reference. The
components to be checked are :
3.1.1

The test scenario configurations (xml files) and

The firmware versions for the tester hardware itself.
CWM 500 Firmware
The firmware version can be checked and maintained in the R&S Version Manager. Basic information
on software update and installation with the R&S Version Manager is given in the "R&S CMW500
Protocol Testing" quick start guide (1202.3857.62). The R&S Version Manager help provides more
details on R&S Version Manager functions and handling of software units. This document assumes that
all required software units can be installed by the user.
The R&S Version Manager can be opened via the START menu:
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
28/44
Revision History
Once opened there are two ways to verify similarity of firmware
versions:
by hand via stepping through the license options or
by exporting the firmware (software status).
The picture shows the version manager with the stepping through
each firmware license:
The next picture shows the menu from which the status export can
be called:
After this a pop‐up window appears with three possible choices.
Only the top one has to be selected as shown in the picture:
After this the location of the status export file needs to be chosen.
Once done the file can be compared to the reference file which is
located under:
..\version\lab2\lab2_cfg.html
3.1.2
Test Scenario
The test scenario ml_002 EPS ‐ Bearer Setup is used for this setup and is contained by the SW option
KF500 with MLAPI Example Scenarios.
The path to the configuration directory is following:
c:\Rohde‐Schwarz\Scenarios\16.6_callSetup_1\APPL\MLAPI\LTE_SAMPLE_SCN\1.0\ml_002\msg
The directory “msg” is part of the CDK delivery and contains several xml files. It has to be noted that
the xml version of the xml files needs to be compliant to the installed tester firmware.
Otherwise strange errors occur during test case execution!
http://www2.rohdeschwarz.com/en/products/test_and_measurement/mobile_radio/CMW500-|Demo-|-48-|-5420.html
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
29/44
Revision History
3.1.3
AT Commands
Network attach in CallBox Mode, LTE band 7.
at+xact=6,2,1,107
at+cgdcont=1,"IP",”www.rohde-schwarz.com”
This gives OK if the SIM cart is inserted accurately.
at+cops=1,2,"00101",7
3.1.4
The Data Application Unit
Install the Data Application Unit
The Data Application Unit (DAU) package has to be installed on the CMW.
In case the DAU hardware is populated, the software (SW) should already be installed as well. Check
this in "SetupSW/HW‐EquipmentInstalled software".
Before installation:

Terminate the CMW BaseSW application – close the window with ‘X’

In the task manager kill the process "ComponentEnvironmentServer_2.5.exe".

Install the DAU‐SW package "SetupCMW_DAU_Support (Release)‐V1.0.15.22"
directly on the CMW.

Reboot the CMW device.
Installation:
Activate DHCP in Data Application Control
After complete startup of the CMW BaseSW application, follow the steps below to configure the DAU
for DHCP:
Make sure your Router is connected to the "LAN DAU" ETH
port at the back side of the CMW.
Open the SETUP menu on the right side.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
30/44
Revision History
Open the DAU configuration via menu:
Data Appl. Control  Go to config
Configure the DAU to use DHCP
As shown on the screenshot, choose last check mark
DHCPv4 from LAN (LAN DAU) for IPv4 Address Configuration
Close the CMW BaseSW (ALT + F4) and start it again
afterwards by a DoubleClick on the desktop link "CMW 1.0"
After the restart, check the "DHCP Status" in the same
window. A green light indicates that the DAU could acquire an
IPv4 address via DHCP.
Switching UPC from PPC (SUW) to DAU
In order to let the scenario use the UPC (=Uplane Control) on the DAU (and not as per default on the
PPC), two XML files have to be replaced in the topology:
 sequencer.xml,
 pipe.xml
Copy these two files to C:\Rohde‐Schwarz\Scenarios\16.6\APPL\MLAPI\rstopology\LTE\.
NOTE:
It is recommended to make a back‐up of the original files before.
Start the LTE scenario
Start the LTE scenario now.
During the Default EPS Bearer Setup the UE will get an IP address which was acquired by the DAU
before.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
31/44
Revision History
Manual DNS settings
On the LTE host which connects to the internet, the DNS
server has to be configured manually, because the DAU does
not yet support automatic DNS provisioning (ask your IT).
In case of a LTE notebook adapter, the DNS server will be
configured on the IP properties pane:
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
32/44
Revision History
Regulatory Notice
Japanese Radio Law and Japanese Telecommunications Business Law Compliance.
This device is granted pursuant to the Japanese Radio Law (電波法)
and the Japanese Telecommunications Business Law (電気通信事業法)
This device should not be modified (otherwise the granted designation number will
become invalid)
Manual Information to the End User :
The OEM integrator has to be aware the end user manual shall include all required regulatory
information/warning as show in this manual.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
33/44
Revision History
Abbreviations / Terminology
A‐GPS
Assisted‐GPS (Global Positioning System)
AP
Application Processor
BB
Baseband
CMOS
Complementary Metal Oxide Semiconductor
CN
Comneon
DigRF v4
Digital RF interface v4 (rmainly used for 4G)
DigRF 3.09
Digital RF interface v3 for (mainly used for 2G/3G)
ETM
Embedded Trace Macrocell
ESD
Electrostatic discharge
fps
Frames Per Second
GPIO
General purpose input/output
GSM
Global System for Mobile Communications
USB‐HS
High Speed. USB2.0 (480MBit/sec)
JPEG
Joint Photographic Experts Group
JTAG
Joint Test Action Group
LDO
Low dropout (regulator)
LED
Light‐emitting diode
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
34/44
Revision History
MIPI
Mobile Industry Processor Interface
MMC(I)
Multimedia Card (Interface)
MPU
Microprocessor unit
PA
Power Amplifier
PCL
Port Control Logic
PMU
Power Management unit
PTI
Parallel Trace Interface
SD‐Card
Secure Digital Card
SMT pin header
Surface Mount Technology pin header
SPI
Serial Peripheral interface
S4G
SMARTi™ 4G
ST MIPI
System Trace MIPI
STT
System Trace Tool
SVB
System verification board
SW
Software
TAP
Test Access Port
TCU
Test Control Unit
USB
Universal Serial Bus
USIF
Universal Serial Interface
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
35/44
Revision History
Appendix A
Definitions/Explanations
Eval Board
special processor socket board for X‐GOLD™ 716 component verification
Lauterbach
Supplier of Debug and Trace environment for X‐GOLD™ 716 (e.g. JTAG, ETM7/11, ST MIPI)
Modem board
Main part of XMM™ 7160 platform hardware (see Error! Reference source not found.)
XMM™ 7160
Project name of Intel platform with key component X‐GOLD™ 716
RF‐ Engine
RF part of platform (RF‐transceiver, Power amplifiers, LNA, Filter bank, antenna switch etc.).
SMARTi™ 4G
Intel RF‐transceiver for 2G/3G/4G
Janus board
Board with SMARTi™ LU and SMARTi™ UE2
Carrier board
SMB needs a carrier board for operation
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
36/44
Revision History
Appendix B Regulatory Statements
USA FCC Radio Frequency Exposure
The FCC with its action in ET Docket 96-8 has adopted a safety
standard for human exposure to radio frequency (RF) electromagnetic
energy emitted by FCC certified equipment. The wireless adapter meets
the Human Exposure limits found in OET Bulletin 65, supplement C,
2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio
according to the instructions found in this manual will result in
exposure substantially below the FCC’s recommended limits.
The following safety precautions should be observed:




Do not touch or move antenna while the unit is transmitting or receiving.
Do not hold any component containing the radio such that the antenna is
very close or touching any exposed parts of the body, especially the face or
eyes, while transmitting.
Do not operate the radio or attempt to transmit data unless the antenna is
connected; this behavior may cause damage to the radio.
Use in specific environments:
 The use of wireless adapters in hazardous locations is limited by the
constraints posed by the safety directors of such environments.
 The use of electronic devices equipped with wireless adapters on
airplanes is governed by rules for each commercial airline operator.
 The use of wireless adapters in hospitals is restricted to the limits set
forth by each hospital.
Explosive Device Proximity Warning
Warning: Do not operate a portable transmitter (including this
wireless adapter) near unshielded blasting caps or in an
explosive environment unless the transmitter has been modified
to be qualified for such use.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
37/44
Revision History
Use On Aircraft Caution
Caution: Regulations of commercial airline operators and the
FCC may prohibit airborne operation of certain electronic
devices equipped with radio-frequency wireless devices
(wireless adapters) including cellular devices because their
signals could interfere with critical aircraft instruments.
The Wireless Adapter and Your Health
The wireless adapter, like other radio devices, emits radio
frequency electromagnetic energy. The level of energy emitted
by the wireless adapter, however, is less than the
electromagnetic energy emitted by other wireless devices such
as mobile phones. The wireless adapter operates within the
guidelines found in radio frequency safety standards and
recommendations. These standards and recommendations
reflect the consensus of the scientific community and result
from deliberations of panels and committees of scientists who
continually review and interpret the extensive research
literature. In some situations or environments, the use of the
wireless adapter may be restricted by the proprietor of the
building or responsible representatives of the applicable
organization. Examples of such situations may include:


Using the wireless adapter on board airplanes, or
Using the wireless adapter in any other environment where the risk of
interference with other devices or services is perceived or identified as
being harmful.
If you are uncertain of the policy that applies to the use of
wireless adapters in a specific organization or environment (an
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
38/44
Revision History
airport, for example), you are encouraged to ask for
authorization to use the adapter before you turn it on.
REGULATORY INFORMATION
USA ‐ Federal Communications Commission (FCC)
No configuration controls are provided for Intel® wireless
adapters allowing any change in the frequency of operations
outside the FCC grant of authorization for U.S. operation.


Intel® wireless adapters are intended for OEM integrators only.
If Intel® wireless adapters are to be co-located with any other transmitter
additional testing and/or approval by the FCC will be required.
This wireless adapter complies with Part 15 of the FCC Rules.
Operation of the device is subject to the following two
conditions:


This device may not cause harmful interference.
This device must accept any interference that may cause undesired
operation.
Class B Device Interference Statement
This wireless adapter has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This wireless adapter generates, uses, and can
radiate radio frequency energy. If the wireless adapter is not
installed and used in accordance with the instructions, the
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
39/44
Revision History
wireless adapter may cause harmful interference to radio
communications. There is no guarantee, however, that such
interference will not occur in a particular installation. If this
wireless adapter does cause harmful interference to radio or
television reception (which can be determined by turning the
equipment off and on), the user is encouraged to try to correct
the interference by taking one or more of the following
measures:




Reorient or relocate the receiving antenna of the equipment experiencing
the interference.
Increase the distance between the wireless adapter and the equipment
experiencing the interference.
Connect the computer with the wireless adapter to an outlet on a circuit
different from that to which the equipment experiencing the interference
is connected.
Consult the dealer or an experienced radio/TV technician for help.
NOTE: The adapter must be installed and used in strict
accordance with the manufacturer's instructions as described in
the user documentation that comes with the product. Any other
installation or use will violate FCC Part 15 regulations.
Canada – Industry Canada (IC)
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference
that may cause undesired operation of the device.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
40/44
Revision History
Cet appareil se conforme aux normes Canada d'Industrie de
RSS permis-exempt. L'utilisation est assujetti aux deux
conditions suivantes: (1) cet appareil ne peut pas causer
d'interférences, et (2) cet appareil doit accepter des
interférences , y compris des interférences qui peuvent causer
desopérations non désirées de l'appareil.
Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
Selon les règlements de Canada d'Industrie, cet émetteur de
radio peut seulement fonctionner en utilisant une antenne du
type et de gain maximum (ou moindre) que le gain approuvé
pour l'émetteur par Canada d'Industrie. Pour réduire
lesinterférences radio potentielles avec les autres utilisateurs, le
type d'antenne et son gain devraient être choisis de façon à ce
que la puissance isotrope rayonnée équivalente(P.I.R.E.) ne soit
pas supérieure à celle qui est nécessaire pour une
communication réussie.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
41/44
Revision History
Safety Approval Considerations
This device has been safety approved as a component and is for
use only in complete equipment where the acceptability of the
combination is determined by the appropriate safety agencies.
When installed, consideration must be given to the following:



It must be installed into a compliant host device meeting the requirement of
UL/EN/IEC 60950-1 2nd edition including the general provisions of
enclosure design 1.6.2 and specifically paragraph 1.2.6.2 (Fire Enclosure).
The device shall be supplied by a SELV source when installed in the enduse equipment.
A heating test shall be considered in the end-use product for meeting the
requirement of UL/EN/IEC 60950-1 2nd edition.
INFORMATION FOR OEMs and HOST INTEGRATORS
The guidelines described within this document are provided to
OEM integrators installing Intel® wireless adapters in
notebook and tablet PC host platforms. Adherence to these
requirements is necessary to meet the conditions of compliance
with FCC rules, including RF exposure. When all antenna type
and placement guidelines described herein are fulfilled the
Intel® wireless adapters may be incorporated into notebook
and tablet PC host platforms with no further restrictions. If any
of the guidelines described herein are not satisfied it may be
necessary for the OEM or integrator to perform additional
testing and/or obtain additional approval. The OEM or
integrator is responsible to determine the required host
regulatory testing and/or obtaining the required host approvals
for compliance.

Intel® wireless adapters are intended for OEMs and host integrators only.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
42/44
Revision History



The Intel® wireless adapter FCC Grant of Authorization describes any
limited conditions of modular approval.
The Intel® wireless adapters must be operated only within countries that
have been approved for operation.
Changes or modification to Intel® wireless adapters by OEMs, integrators
or other third parties is not permitted. Any changes or modification to
Intel® wireless adapters by OEMs, integrators or other third parties will
void authorization to operate the adapter.
Simultaneous Transmission of Intel® Wireless Adapters with
Other Integrated or Plug‐In Transmitters
Based upon FCC Knowledge Database publication number
616217
https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm
?id=33240&switch=P, when there are multiple transmitting
devices installed in a host device, an RF exposure transmitting
assessment shall be performed to determine the necessary
application and test requirements. OEM integrators must
identify all possible combinations of simultaneous transmission
configurations for all transmitters and antennas installed in the
host system. This includes transmitters installed in the host as
mobile devices (>20 cm separation from user) and portable
devices (<20 cm separation from user). OEM integrators
should consult the actual FCC KDB 616217 document for all
details in making this assessment to determine if any additional
requirements for testing or FCC approval is necessary.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
43/44
Revision History
5.1.1
Information To Be Supplied to the End User by the
OEM or Integrator
The following regulatory and safety notices must be published
in documentation supplied to the end user of the product or
system incorporating the Intel® wireless adapter, in
compliance with local regulations. Host system must be labeled
with "Contains FCC ID: XXXXXXXX", FCC ID displayed on
label.
The Intel® wireless adapter must be installed and used in strict
accordance with the manufacturer's instructions as described in
the user documentation that comes with the product. Intel
Corporation is not responsible for any radio or television
interference caused by unauthorized modification of the devices
included with the wireless adapter kit or the substitution or
attachment of connecting cables and equipment other than that
specified by Intel Corporation. The correction of interference
caused by such unauthorized modification, substitution or
attachment is the responsibility of the user. Intel Corporation
and authorized resellers or distributors are not liable for any
damage or violation of government regulations that may arise
from the user failing to comply with these guidelines.
Rev. 1.2, Feb. 2015
Hardware User
Guide, Document Number: N/A
44/44

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : schacket
Create Date                     : 2015:07:25 09:46:34-04:00
Modify Date                     : 2015:07:25 09:46:34-04:00
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - Intel_7262M2WW_UserGuide_V1 2
Creator                         : schacket
Producer                        : Acrobat Distiller 15.0 (Windows)
Document ID                     : uuid:a9e423b2-d047-487b-ad9f-f9b33db3d3e0
Instance ID                     : uuid:e842c03b-5771-4e5d-ba09-549c8256032a
Page Count                      : 44

EXIF Metadata provided by EXIF.tools