Interactive Technologies IQ69 Marine Device Remote Control Transmitter User Manual
Interactive Technologies, Inc. Marine Device Remote Control Transmitter
user manual
Marine Remote Commander System MC10 • Operating Instructions Please read before using this equipment. ALPINE ELECTRONICS MARKETING, INC. ALPINE electronics of u.k., ltd. 1-1-8 Nishi Gotanda Shinagawa-ku Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE House Fletchamstead Highway, Coventry CCV4 9TW, U.K. Phone 0870-33 33 763 ALPINE Electronics of America, inc. (RCS PONTOISE B 338 101 280) 98, Rue de la Belle Etoile, Z.I. paris Nord II, B.P. 50016, 95945 Roissy Charles de Gaulle Cedex, France Phone 01-48638989 19145 Gramercy Place Torrance, California 90501 U.S.A. Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE Electronics of Canada, Inc. 777 Supertest Road Toronto Ontario M3J 2M9, Canada Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE electronics of australia pty, ltd. 161-165 Princess Highway, Hallam Victoria 3803, Australia Phone 03-8787-1200 ALPINE Electronics GmbH Wilhelm-Wagenfeld-Str. 1-3 80807 München, Germany Phone 089-32 42 640 ALPINE ELectronics France S.a.r.l. ALPINE Italia S.p.a. Viale C. Colombo 8, 20090 Trezzano Sul Naviglio (MI), Italy Phone 02-484781 ALPINE ELECTRONICS DE ESPAÑa, S.A. Portal de Gamarra 36, Pabellón, 32 01013 Vitoria (Alava)-APDO 133, Spain Phone 945-283588 ALPINE ELECTRONICS (BENELUX) GmbH Leuvensesteenweg 510-B6, 1930 Zaventem, Belgium Phone 02-725 1315 Printed in China Operating Instructions WARNING CAUTION This symbol means important instructions. Failure to heed them can result in injury or material property damage. WARNING This symbol means important instructions. Failure to heed them can result in serious injury or death. HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Center for replacing. DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR BOAT. Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the boat in a safe location before performing these functions. Failure to do so may result in an accident. PRECAUTIONS KEEP THE VOLUME AT LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISES WHILE DRIVING. Excessive volume levels that obscure sounds such as emergency vessel sirens or approaching vessels can be dangerous and may result in an accident. LISTENING AT LOUD VOLUME LEVELS IN A BOAT MAY ALSO CAUSE HEARING DAMAGE. Product Cleaning Use a soft dry cloth for periodic cleaning of the product. For more severe stains, please dampen the cloth with water only. Anything else has the chance of dissolving the paint or damaging the plastic. Temperature Be sure the temperature inside boat is between +60°C (+140°F) and -10°C (+14°F) before turning your unit on. MINIMIZE DISPLAY VIEWING WHILE DRIVING. Viewing the display may distract the driver from looking ahead of the boat and cause an accident. DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or electric shock. Maintenance If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing. DO NOT CONNECT A POWER SUPPLY OTHER THAN A DC 12V NEGATIVE GROUND TYPE. Failure to do so may result in accident or fire. FCC Compliance Statement Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. KEEP SMALL OBJECTS SUCH AS BOLTS OR SCREWS OUT OF THE REACH OF CHILDREN. Swallowing them may result in serious injury. If swallowed, consult a physician immediately. USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed application may result in fire, electric shock or other injury. Basic Operation Basic Operation Basic Operation Installation Installation MC10 Display Unit Optional RUE-M1RF Optional Add-on Commander 333MHz Wireless 2.4GHz Wireless GND GND MC1 +12V 2.4GHz Wireless MC10 Transceiver Unit GND +12V +12V IDA-X100M To 10P Sub Display Connector OR To Steering Wheel Jack GND +12V BLACK : connect to Ground (GND) YELLOW : connect to 12V(+): ACC (switched) BLACK : connect to Ground (GND) RED : connect to 12V(+): ACC (switched) CDA-9886M Program Menu MC10 Display unit Enter Program Mode Program Menu Options 1. ID NUMBER This is the serial number of the display unit. * Range of serial numbers: 00001 to 99999 2. RF STRENGTH Signal strength between a display unit and the closest display or transceiver unit in the MC10 wireless system * Range of strength: [ to 3. SIGNAL STATUS Wireless signal connection status between a display unit and the transceiver unit * Values: [CONNECTED, NO CONNECT] 4. MESH NET When set to ON, turns a display unit into a signal repeater for communicating with MC1 add-on commander units that are installed outside the MC10 system communication range * Values: [OFF, ON] 5. CONTRAST Sets brightness or dimness of LCD display characters * Values: [5, 4, 3, 2, 1, 0] 6. BL DISPLAY Turns LCD backlighting ON or OFF 7. BL KEYPAD Turns keypad button backlighting ON or OFF 8. TEMPERATURE Sets temperature scale to degrees F or degrees C 9. RESET MC1 Menu selection for pairing or re-pairing any MC1 or MC10 display units with any existing MC10 system. RESET MC1 also restores factory default setting * Note: Bold indicates default menu selection for this program menu option Program Mode Example 1. Enter Program Mode 4. Press VOL + or VOL – to adjust the current CONTRAST value 2. Press VOL + or VOL – until CONTRAST shows on top line of display 5. Press ENT to save new CONTRAST value 3. Press ENT to program new CONTRAST value 6. Press ESC to exit Program Mode MC1 Add-on Commander Pairing Procedure 1. Power on existing MC10 system 2. Connect power and ground wires of MC1 add-on commander (see Installation) 3. MC1 add-on commander display will turn on and automatically go to the pairing screen in the program menu with ADD MC1 showing on the display ADD MC1 MC1 Paring Screen 4. On marine radio, select FM Tuner as source (make sure that tuner seek mode is DX or LOCAL , not MANUAL) 5. Found Radio will appear on the display below ADD MC1 when add-on commander is ready to pair with MC10 system * ADD MC1 Found Radio 6. On marine radio, press SEEK UP ( 7. PRESS ENTER will appear below ADD MC1 on the display ) once ADD MC1 PRESS ENTER 8. Press ENT to finish pairing operation and save new settings 9. Press ESC to exit Program Menu 10. Turn off the existing MC10 system, then turn it back on. Pairing procedure is now completed. *If Found Radio does not appear on the display, MC1 location may be out of MC10 system range (typical ~ 40 feet/12 m) - See Mesh Network Operation section on page 8. Mesh Network Operation Mesh Network OFF Transceiver 2.4GHz Wireless APN Marine Head Unit MC10 Marine Commander System Mesh Network OFF Transceiver 2.4GHz Wireless 2.4GHz Wireless MC1 Add on APN Marine Head Unit MC10 Marine Commander System with MC1 Add on Commander Mesh Network Operation To install an MC1 Add-on Commander in a new location that is outside the MC10 system range: 1. Go to the MC10 system display unit that is closest to the new location 2. Turn Mesh Network ON in the program menu, then exit program menu 3. Follow the MC1 Add-on Commander Pairing Procedure on page 6 to complete the new installation * When MESH NET is turned ON in the program menu of a display unit, it becomes a signal repeater for extending the MC10 system range. Mesh Network OFF Mesh Network ON Transceiver MC1 Add on MC10 2.4GHz Wireless 2.4GHz Wireless APN Marine Head Unit MC10 Marine Commander System MC10 Display Unit Re-Pairing Procedure * If for some reason you want to pair an MC10 display unit with a different MC10 system than the one it was purchased with (just like adding an MC1 Commander) follow the instructions below: 1. Power on the MC10 system that you want to add the additional MC10 display unit to 2. Connect power and ground wires of new MC10 display unit 3. Wait at least 20 seconds, then enter the Program Menu (see Program Menu Example) 4. Go to the RESET MC1 option, then press ENT button 5. MC10 display unit will reset itself (including factory default settings) and display will show ADD MC1 like in step 3 of the previous section (MC1 Add-on Commander Pairing Procedure) 6. Follow the remaining steps of the previous section to complete this operation
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No XMP Toolkit : Adobe XMP Core 4.0-c006 1.236519, Wed Jun 14 2006 08:31:24 Instance ID : uuid:7c697c7c-144b-457b-a4a4-852391a0c8e2 Document ID : adobe:docid:indd:ffdaa1e6-2cd1-11de-baa5-a88b5df050a8 Rendition Class : proof:pdf Derived From Instance ID : d2bd13c9-0fec-11de-82f1-bbddb0738825 Derived From Document ID : adobe:docid:indd:398501aa-0fda-11de-8eec-9a3d4d96fdef Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:9BA3514291C611DB8CAC81FF46EAA8A8, uuid:6E92A94208B211DE8FA9A766147D08B4, uuid:6E92A94208B211DE8FA9A766147D08B4, uuid:6E92A94208B211DE8FA9A766147D08B4, uuid:513465DE2CCD11DEADA3CB195A2CD9D5, uuid:407f2361-7a20-43d9-a235-f045b481da85, uuid:407f2361-7a20-43d9-a235-f045b481da85, uuid:407f2361-7a20-43d9-a235-f045b481da85, uuid:6612ADE90A2D11DE88AF8515393A9163, uuid:190AFA480AFF11DE8B52B0E5E0730C10, uuid:190AFA470AFF11DE8B52B0E5E0730C10, uuid:3BC0A13F0FE611DEA88DE31B27F9BA2E, uuid:1C0F8C2E0BD711DEBC3AB49462E43619, uuid:1C0F8C300BD711DEBC3AB49462E43619, uuid:352A878F0BF311DEBC3AB49462E43619, uuid:352A878D0BF311DEBC3AB49462E43619, uuid:3BC0A1400FE611DEA88DE31B27F9BA2E, uuid:3BC0A1440FE611DEA88DE31B27F9BA2E Manifest Reference Document ID : uuid:9BA3514191C611DB8CAC81FF46EAA8A8, uuid:6E92A94108B211DE8FA9A766147D08B4, uuid:6E92A94108B211DE8FA9A766147D08B4, uuid:6E92A94108B211DE8FA9A766147D08B4, uuid:C55DB8C3096E11DEA1EC9CCFBB6E111D, uuid:6E92A93908B211DE8FA9A766147D08B4, uuid:6E92A93908B211DE8FA9A766147D08B4, uuid:6E92A93908B211DE8FA9A766147D08B4, uuid:C55DB8C5096E11DEA1EC9CCFBB6E111D, uuid:6612ADE70A2D11DE88AF8515393A9163, uuid:E56E60720A4E11DE88AF8515393A9163, uuid:6612ADE20A2D11DE88AF8515393A9163, uuid:1C0F8C2D0BD711DEBC3AB49462E43619, uuid:1C0F8C2F0BD711DEBC3AB49462E43619, uuid:352A878E0BF311DEBC3AB49462E43619, uuid:352A878C0BF311DEBC3AB49462E43619, uuid:E56E60790A4E11DE88AF8515393A9163, uuid:E56E607C0A4E11DE88AF8515393A9163 Create Date : 2009:04:27 16:55:01-07:00 Modify Date : 2009:04:27 16:55:21-07:00 Metadata Date : 2009:04:27 16:55:21-07:00 Creator Tool : Adobe InDesign CS3 (5.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 9508 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 8.0 Trapped : False Page Count : 8 Creator : Adobe InDesign CS3 (5.0)EXIF Metadata provided by EXIF.tools