Intermec Technologies 1000CP01SX1 1000CP01S, 1000CP02S, 1001CP01S, 1000CP03S User Manual 933 274 002
Intermec Technologies Corporation 1000CP01S, 1000CP02S, 1001CP01S, 1000CP03S 933 274 002
Contents
Compliance Insert
CN70 Mobile Computer Compliance Insert
Model 1000CP03C, 1000CP03S
The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of
accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void
the compliance of this product and may result in the loss of the user’s authority to operate the equipment.
Battery and Power Supply Information
Laser Compliance and Precaution
The 1000CP03C and 1000CP03S are registered with the CDRH as Class II LASER Products (21 CFR Subchapter J, Part 1040). These products
have a maximum output of 1 mW at 630-680 nm.
Note: There are no controls or adjustments provided for routine operation or maintenance of the 1000CP03C or 1000CP03S.
FCC Digital Emissions Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the radio or television receiving antenna.
•Increase the separation between the computer equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
•Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
802.11 Radio Precaution Statement
Radiation Exposure Statement
Radio Frequency (RF) Radiation Exposure - Specific Absorption Rate (SAR) Information
Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposure beyond the limits
established for this equipment. The only approved body-worn accessory is the SWA developed wrist holster providing 12 mm of separation
from the left side of the computer.
Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future
reference.
Caution: For use with Intermec battery pack Model 1000AB01 or 1000AB02 only. See battery instructions. For power supply, use
Intermec Model 9001AE02 or Model 9002AX02. No user-serviceable parts.
Charge only in Intermec Models 1000CP03C or 1000CP03S or with base 1002UU01, 1002UU02, 1002UU03, 1002UU04, or
1002UU05 using 1002UC01 or 1002UD01 adapters. Use of incorrect charger may present a risk of fire or explosion.
Caution: There are no user serviceable parts inside the 1000CP03C or 1000CP03S. Use of controls or adjustments, or performance of
procedures other than those specified herein, may result in hazardous laser light exposure of up to 1 mW at 630-680 nm.
Caution: Users are responsible for configuring the channels of operation that comply with their country regulatory standards. A
Wireless Network Administrator should review the operating restrictions detailed within the Access Point installation manual.
Caution: 802.11a wireless LAN 5.15 to 5.25 GHz (5 GHz radio channels 34 to 48) is restricted to indoor operations to reduce harmful
interference to co-channel Mobile Satellite System (MSS) operations.
Warning: This equipment complies with International Commission on Non-Ionizing Radiation Protection (ICNIRP), IEEE C95.1,
and Federal Communications Commission Office of Engineering and Technology (OET) Bulletin 65 limits for exposure to radio
frequency (RF) radiation.
Worldwide Headquarters
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
© 2012 Intermec Technologies
Corporation. All rights reserved.
CN70 Mobile Computer Compliance Insert
*933-274-002*
P/N 933-274-002, Revision B
Radio Frequency (RF) Exposure - Specific Absorption Rate (SAR) Test Results for Model 1000CP03C:
Radio Frequency (RF) Exposure - Specific Absorption Rate (SAR) Test Results for Model 1000CP03S:
Radio Technology W/kg Comment
CDMA 0.517
1.190
At the ear
For body-worn operation
802.11abgn 0.239
0.398
At the ear
For body-worn operation
Bluetooth N/A Negligible due to very low output power
Radio Technology W/kg Comment
CDMA
Cellular
PCS
0.439
0.790
0.722
0.753
At the ear
For body-worn operation
At the ear
For body-worn operation
UMTS
Cellular
PCS
AWS
0.246
0.787
0.408
0.765
0.568
0.780
At the ear
For body-worn operation
At the ear
For body-worn operation
At the ear
For body-worn operation
802.11abgn 0.069
0.296
At the ear
For body-worn operation
Bluetooth N/A Negligible due to very low output power