Intermec Technologies NOVCDPD Mobile Computer with WAN CDPD radio User Manual 020117A1

Intermec Technologies Corporation Mobile Computer with WAN CDPD radio 020117A1

20020117 app A user manual

Download: Intermec Technologies NOVCDPD Mobile Computer with WAN CDPD radio User Manual 020117A1
Mirror Download [FCC.gov]Intermec Technologies NOVCDPD Mobile Computer with WAN CDPD radio User Manual 020117A1
Document ID221924
Application IDdOAwGmCVaN3iKpveyRqjHQ==
Document Description20020117 app A user manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize16.4kB (204959 bits)
Date Submitted2002-01-22 00:00:00
Date Available2002-01-24 00:00:00
Creation Date2002-01-22 15:25:23
Producing SoftwareAcrobat PDFWriter 4.0 for Windows
Document Lastmod2002-01-22 16:24:13
Document Title020117A1.PDF
Document CreatorMicrosoft Word
Document Author: Intermec User

Intermec Technologies Corporation
EMC Test Lab
DOC. NO.: 577-501-008
700 CDPD, FCC 2.1053 Radiated Spurious Emissions, Appendix A
FCC ID: EHANOVCDPD
REPORT NO: 20020117-1
Page 1 of 18
MEASUREMENT/TECHNICAL REPORT
Technologies Corporation
EMC Test Laboratory
Cedar Rapids, IA
Intermec Technologies Corporation
700 With Novatel CDPD
Cellular Radio Module
REPORT NO: 20020117-1
DATE: January 17, 2002
APPENDIX A
NOVATEL USERS MANUAL
EXPEDITE
WIRELESS IP MODEM
HARDWARE INTERFACE
SPECIFICATION
OM - 01016529
Revision 3
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
1 of 17
3.0
REVISION HISTORY
REV#
ECO#
99007
99024
99047
EFF. DATE
990709
990809
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
DESCRIPTION
Initial release.
Change order of pins 21 and 22
Add mounting instructions
PREPARED
P. Faubert
P. Faubert
K. Frayn
APPROVED
S. Smilar
S. Smilar
S. Smilar
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
2 of 17
3.0
The information disclosed herein is the exclusive property of NOVATEL WIRELESS TECHNOLOGIES
LTD. and is not to be disclosed without the written consent of NOVATEL WIRELESS TECHNOLOGIES
LTD. No part of this publication may be reproduced or transmitted in any form or by any means including
electronic storage, reproduction, execution or transmission without the prior written consent of NOVATEL
WIRELESS TECHNOLOGIES LTD. The recipient of this document by its retention and use, agrees to
respect the security status of the information contained herein.
The information disclosed herein is the exclusive property of Novatel Wireless Technologies Ltd. and is
not to be disclosed without the written consent of Novatel Wireless Technologies Ltd. No part of this
publication may be reproduced or transmitted in any form or by any means including electronic storage,
reproduction, execution or transmission without the prior written consent of Novatel Wireless
Technologies Ltd. The recipient of this document by its retention and use, agrees to respect the security
status of the information contained herein.
This document is intended for limited circulation.
The information contained in this document is subject to change without notice and should not be
construed as a commitment by NOVATEL WIRELESS TECHNOLOGIES LTD. unless such commitment
is expressly given in a covering document.
© Copyright NOVATEL WIRELESS TECHNOLOGIES LTD. (1999)
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
3 of 17
3.0
Table of Contents
WARNING ........................................................................................................................................ 6
INTRODUCTION.............................................................................................................................. 6
SCOPE............................................................................................................................................. 6
SPECIFICATIONS ........................................................................................................................... 6
4.1
Physical Interface ...................................................................................................................... 6
4.1.1
Data/Power Connection ...................................................................................................... 7
4.1.2
RF Antenna Connector Type............................................................................................... 8
4.1.3
Pin Descriptions.................................................................................................................. 9
4.2
Host Interface Specifications ................................................................................................... 10
4.2.1
Serial Data Rate and Format ............................................................................................ 10
4.3
Radio Specifications ................................................................................................................ 10
4.3.1
Airlink Data Rate............................................................................................................... 10
4.3.2
Recommended Antenna Type........................................................................................... 10
4.3.3
Frequency Range ............................................................................................................. 10
4.3.4
Duplex Mode .................................................................................................................... 10
4.3.5
RF Power Class ................................................................................................................ 10
4.4
Electrical Specifications........................................................................................................... 11
4.5
Mechanical Specifications........................................................................................................ 12
4.5.1
Dimensions....................................................................................................................... 12
4.5.2
Weight .............................................................................................................................. 12
4.6
Environmental Specifications................................................................................................... 12
4.6.1
Temperature Range.......................................................................................................... 12
4.6.2
Humidity ........................................................................................................................... 12
4.6.3 ............................................................................................................................................... 12
4.6.4
Shock Stability.................................................................................................................. 13
4.6.5
Vibration Stability.............................................................................................................. 13
4.6.6
Regulatory compliance ..................................................................................................... 13
4.6.7
ESD Protection ................................................................................................................. 13
4.7
CDPD Part 409 Compliance .................................................................................................... 14
INSTALLATION INSTRUCTIONS.................................................................................................. 15
5.1
Antenna Mounting.................................................................................................................... 15
5.2
Antenna ................................................................................................................................... 15
5.3
Labeling................................................................................................................................... 15
5.4
User Manual ............................................................................................................................ 15
PACKAGING REQUIREMENTS .................................................................................................... 17
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
4 of 17
3.0
6.1
Shipping Packaging ................................................................................................................. 17
6.2
Labeling................................................................................................................................... 17
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
5 of 17
3.0
1 WARNING
All persons must be at least 20 cm from the antenna when transmitter operating to meet FCC RF
exposure requirements. Refer to the Installation Instructions section for specific requirements for the
antenna used with module.
2 INTRODUCTION
This document describes the hardware interface for the Novatel Wireless Expedite Wireless IP Modem.
The Expedite Wireless IP Modem is an OEM module designed for integration into a host product to
provide two-way wireless data communication capability via the CDPD (Cellular Digital Packet Data)
Network.
3 SCOPE
The scope of this document includes all pertinent information for describing the capabilities and
operating requirements for the product in order to determine suitability for specific market applications.
Internal design issues, detailed operating instructions and cost information is not included in this
document.
4 SPECIFICATIONS
4.1 Physical Interface
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
6 of 17
3.0
4.1.1 Data/Power Connection
One connector is used to physically connect the power supply and 3.3 volt logic level host
communication interface signals to the Expedite Wireless IP Modem.
4.1.1.1 Data/Power Connector Type
Description:
Samtec part number:
24-pin, 1.27 mm pitch, SMT, double row low profile socket type
CLP-112-02-F-D
Some interface connector options are provided here for reference. Contact Samtec for the latest
connector mating options.
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
7 of 17
3.0
4.1.1.2 Surface Mount Mating Connector Options
Description:
24-pin, 1.27 mm pitch, SMT, double row, zero profile, pin type header
Samtec part number: DIS5-112-52-F-D-VS
NOTE: This connector provides the lowest profile interface solution.
Description:
Samtec part number:
24-pin, 1.27 mm pitch, SMT, double row, low profile, pin type header
FTS-112-03-F-DV
4.1.1.3 Through-Hole Mating Connector Options
Description:
Samtec part number:
24-pin, 1.27 mm pitch, T/H, double row, zero profile, pin type header
DIS5-112-52-F-D
Description:
Samtec part number:
24-pin, 1.27 mm pitch, T/H, double row, low profile, pin type header
FTS-112-03-F-D
4.1.2 RF Antenna Connector Type
Expedite Wireless IP Modem antenna connector:
Description
MMCX Coaxial Connector
Manufacturer
Huber and Suhner
Part Number
82MMCX-S50-0-2
NOTE: An equivalent connector by the same or another manufacturer may be used.
Impedance
50 ohm
Expedite Wireless IP Modem mating antenna connector:
Mating connector:
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
AEP 8905-1521-003 or equivalent with RG316 cable.
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
8 of 17
3.0
4.1.3 Pin Descriptions
Pin #
Name
Direction
13, 14
Vcc1
POWER
15, 16
Vcc2
POWER
1,2 &
23,24
GND
POWER
PWR_IND
OUTPUT
SM_IND
OUTPUT
WKUP
INPUT
DTM
INPUT
DFM
OUTPUT
11
RTS
INPUT
10
CTS
OUTPUT
DTR
INPUT
DSR
OUTPUT
12
GPIO1
17
GPIO2
18
GPIO3
19
GPIO4
20
GPIO5
21
GPIO6
22
ADC_IN
BIDIRECTIONAL
BIDIRECTIONAL
BIDIRECTIONAL
BIDIRECTIONAL
BIDIRECTIONAL
BIDIRECTIONAL
ANALOG
INPUT
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
Power-on
Reset State
Description
POWER SUPPLY CONNECTION TO THE MODEM FOR ALL
CIRCUITRY EXCEPT FOR THE RF POWER AMPLIFIER.
POWER SUPPLY CONNECTION TO THE MODEM FOR THE RF
POWER AMPLIFIER ONLY
MODEM GROUND
INPUT WITH
PULLUP
INPUT WITH
PULLUP
INPUT WITH
PULLDOWN
INPUT WITH
PULLUP
INPUT WITH
PULLDOWN
INPUT WITH
PULLUP
ADC INPUT
POWER INDICATOR:
HI: INDICATES THAT THE MODEM IS ON
LO INDICATES THAT THE MODEM IS OFF
SLEEP MODE INDICATOR:
HI: INDICATES THAT THE MODEM IS IN SLEEP MODE
LO INDICATES THAT THE MODEM IS NOT IN SLEEP MODE
WAKE UP INPUT: (ACTIVE HI PULSE)
A PULSE APPLIED TO THIS PIN WILL TURN ON THE MODEM IF
THE MODEM IS OFF, OR WAKE UP THE MODEM IF THE MODEM IS
IN SLEEP MODE. REFER TO THE APPLICATIONS INFORMATION
SECTION FOR MORE DETAILS ON USING THE WAKE UP PIN.
DATA TO MODEM:
(3.3 VOLT LOGIC LEVEL)
IN RS232 TERMS, THIS IS CALLED "TXD".
DATA FROM MODEM:
(3.3 VOLT LOGIC LEVEL)
IN RS232 TERMS, THIS IS CALLED "RXD".
READY TO SEND:
(3.3 VOLT LOGIC LEVEL)
CLEAR TO SEND:
(3.3 VOLT LOGIC LEVEL)
DTE READY:
(3.3 VOLT LOGIC LEVEL)
DCE READY:
(3.3 VOLT LOGIC LEVEL)
GENERAL PURPOSE CONFIGURABLE INPUT OR OUTPUT:
REFER TO THE AT COMMAND SET FOR THE DEFAULT STATE.
GENERAL PURPOSE CONFIGURABLE INPUT OR OUTPUT:
REFER TO THE AT COMMAND SET FOR THE DEFAULT STATE.
GENERAL PURPOSE CONFIGURABLE INPUT OR OUTPUT:
REFER TO THE AT COMMAND SET FOR THE DEFAULT STATE.
GENERAL PURPOSE CONFIGURABLE INPUT OR OUTPUT:
REFER TO THE AT COMMAND SET FOR THE DEFAULT STATE.
GENERAL PURPOSE CONFIGURABLE INPUT OR OUTPUT:
REFER TO THE AT COMMAND SET FOR THE DEFAULT STATE.
GENERAL PURPOSE CONFIGURABLE INPUT OR OUTPUT:
REFER TO THE AT COMMAND SET FOR THE DEFAULT STATE.
ADC INPUT:
THIS PIN IS CONNECTED TO ONE CHANNEL OF AN 8-BIT ADC.
REFER TO THE AT COMMAND SET ON HOW TO READ THIS ADC
VALUE.
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
9 of 17
3.0
4.2 Host Interface Specifications
4.2.1 Serial Data Rate and Format
The Expedite supports asynchronous data transmission of the following rate and format:
Baud Rate (bits/second)
Data bits
Parity
Stop Bits
1200, 2400, 4800, 9600, 19200, 38400
7, 8
Even, None, Odd Mark
1, 2
4.3 Radio Specifications
4.3.1 Airlink Data Rate
Rate
19200 bits per second
Error correction -
Reed Solomon (63,47)
Transmission standard (CDPD System Specification Part 401, Section 4.5.)
4.3.2 Recommended Antenna Type
Type
Impedance
VSWR
Half-Wave Dipole
50 ohm nominal
1.5:1 nominal, 2.0:1 maximum
Note that the module is aligned assuming a 1.2 dB antenna gain (cable loss included in antenna gain).
4.3.3 Frequency Range
Mode
Transmit
Receive
Frequency Range
824 MHz - 849 MHz
869 MHz - 894 MHz
4.3.4 Duplex Mode
Full-Duplex
(CDPD System Specification Version 1.1 part 409, paragraph 4.2)
4.3.5 RF Power Class
Class III (0.6 Watt ERP)
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
10 of 17
3.0
(CDPD System Specification Version 1.1 part 409, paragraph 4.3)
4.4 Electrical Specifications
4.4.1.1 Operating Characteristics (Ta = 0º C to 60º C, VCC1 & VCC2 = 3.6V, unless
otherwise noted.)
SYMBOL
VCC1
VCC2
ICC1
RESADC
PARAMETER / CONDITIONS
MODEM SUPPLY VOLTAGE
RF POWER AMPLIFIER SUPPLY VOLTAGE
MODEM OFF
VCC1 = 3.6V
SLEEP MODE
VCC1 = 3.6V
RECEIVE MODE
VCC1 = 3.6V
TRANSMIT MODE
VCC1 = 3.6V
MODEM OFF
VCC2 = 3.6V
SLEEP MODE
VCC2 = 3.6V
RECEIVE MODE
VCC2 = 3.6V
TRANSMIT MODE
VCC2 = 3.6V
WAKE-UP PULSE WIDTH
FROM SLEEPMODE
FROM POWER UP
INPUT VOLTAGE – LOW (EXCEPT FOR WKUP)
MODEM ON
MODEM OFF
INPUT VOLTAGE - HIGH (EXCEPT FOR WKUP)
MODEM ON
MODEM OFF
INPUT VOLTAGE - LOW (WKUP ONLY) WKUP ONLY
INPUT VOLTAGE - HIGH (WKUP ONLY)
OUTPUT VOLTAGE - LOW (IOL = 1.0mA)
OUTPUT VOLTAGE - HIGH (IOH = -200µA)
MAXIMUM SINK CURRENT
MAXIMUM SOURCE CURRENT
ADC INPUT VOLTAGE
ADC READABLE VOLTAGE RANGE
ABSOLUTE MAXIMUM INPUT VOLTAGE
ADC RESOLUTION
REFADC
DIVADC
ZADC
ADC REFERENCE VOLTAGE
ADC DIVIDER RATIO
ADC INPUT IMPEDANCE
ICC2
TWAKEUP
VIL1(NOTE 1)
VIH1(NOTE 1)
VIL2(NOTE 2)
VIH2(NOTE 2)
VOL(NOTE 1)
VOH(NOTE 1)
IOL(NOTE 1)
IOH(NOTE 1)
VADC
M IN
3.45
3.45
TYPICAL
3.6
3.6
M AX
4.5
4.5
UNITS
µA
mA
130
mA
175
mA
µA
µA
µA
50
725
mA
mSec
10
500
-0.5
0.8
2.0
3.3
-0.5
3.0
2.6
3.3
3.7
0.0
0.5
4.5
0.78
3.4
-1.0
1.0
1.5
mA
mA
5.50
8.50
24
2.048
1:3
300k
BITS
mV
OHMS
NOTE 1 - The specifications apply to all pins on the serial interface connector except for the following pins: GND, VCC1, VCC2 &
ADC_IN. All pins have except VCC1, VCC2 and GND are filtered via a 470pF shunt capacitor and a 330 ohm series resistor which
affects the sink and source capability of the pin.
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
11 of 17
3.0
NOTE 2 - The WKUP pin is not connected directly to the CPU, it is connected though a resistor to the base of an NPN transistor.
4.5 Mechanical Specifications
4.5.1 Dimensions
5.00 mm x 54.00 mm x 72.91 mm
4.5.2 Weight
Approximately:
27g
4.6 Environmental Specifications
4.6.1 Temperature Range
The temperature is defined as per the CDPD System Specification Version 1.1 part 409,
paragraph 5.2.1
Mode
Operating (Compliant)
Operating (De-rated)
Storage
Lower Limit
0 Degrees C
-20 Degrees C
-40 Degrees C
Upper Limit
+60 Degrees C
+60 Degrees C
+85 Degrees C
4.6.2 Humidity
CDPD Part 409 paragraph 5.2.2
50 degrees C
40% RH
8 hours
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
12 of 17
3.0
4.6.3 Shock Stability
CDPD Part 409 paragraph 5.2.3.1
Half sine wave, 20g peak acceleration, 7 to 11 ms
3 impact on each of 6 faces
4.6.4 Vibration Stability
CDPD Part 409 par. 5.2.3.2 (non-operational)
Sinusoidal vibration at 1.5g acceleration swept through 5Hz to 500Hz, 0.1 octave/second
4.6.5 Regulatory compliance
FCC title 47, parts 15 (class B) and 22. Resubmission is not required for the changes made in
this product, including the changes made to name and part number.
4.6.6 ESD Protection
No ESD protection is provided for the Expedite Wireless IP Modem. Expedite is intended to be
used in an OEM application. It is the responsibility of the OEM manufacturer to provide the
necessary ESD protection for their application.
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
13 of 17
3.0
4.7 CDPD Part 409 Compliance
The module will meet the CDPD System Specification Part 409, Small Form-Factor Devices.
CDPD
Part 409
7.1.2.2
7.1.2.3
7.2.3
Specification Parameter
Condition
Upper Limit
RX sensitivity in AWGN
(Note a: small form factor M-ES)
RX sensitivity in Raleigh fading
(Note b: small form factor M-ES)
less than 5% block
error rate
-8 km/hr, 1% ber
-50 km/hr, 1% ber
-100 km/hr, 1% ber
8 us delay
-111 dBm
7.5.3
Co-channel interference rejection
and delay
Adjacent/Alternate channel
selectivity
Intermodulation spurious
response
RSSI
7.6.1.2
Radiated spurious emissions
7.6.2.2
Conducted spurious emissions
8.1.3
8.2.3
Frequency stability
Phase noise
8.3.3
Emission spectrum
8.4.3
8.5.3.3
8.5.4.3
Channel switching time
Power stability (PA power levels)
Switching time requirements – on
to off
Release time requirements
Modulation type
7.3.3
7.4.3
8.5.5.3
8.6.1.3
1 kHz
10 kHz
adjacent channel
alternate channel
second alternate
channel
8.7.1.3
Radiated harmonic and spurious
emissions
8.7.2.3
Conducted harmonic and
spurious emissions
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
-98 dBm
-100 dBm
-101 dBm
17 dB rejection
+/-30 kHz from carrier
+/-60 kHz from carrier
25 - 70 MHz
70 - 130 MHz
130 - 174 MHz
174 - 260 MHz
260 - 470 MHz
470 - 1000 MHz
450 kHz - 2600 MHz
869.01 - 893.07 MHz
824.01 - 848.97 MHz
Lower limit
16 dB
60 dB
57 dB
+ 6 dB absolute
+ 3 dB relative
-45 dBm
-41 dBm
-41 to -32 dBm
-32 dBm
-32 to -26 dBm
-21 dBm
-47 dBm
-80 dBm
-60 dBm
+2.5 PPM
-55 dBc/Hz
-75 dBc/Hz
-26 dBc
-45 dBc
-60 dBc / –
23dBm
(whichever is
lower)
40 ms
+2 dBm
2 ms
2 ms
0.5 + 5%
19.2kbps +
50ppm
- 6 dB absolute
- 3 dB relative
- 2.5 PPM
-4 dBm
0.5 – 5%
19.2kbps – 50ppm
43 + 10 log(mean
output power in
Watts) dB
43 + 10 log(mean
output power in
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
14 of 17
3.0
CDPD
Part 409
Specification Parameter
Condition
Upper Limit
Lower limit
Watts) dB
5 INSTALLATION INSTRUCTIONS
Unless the final product satisfies SAR (Specific Absorption Ratio) compliance through separate FCC
approval, integration of this module into other products has some requirements which are outlined below.
5.1 Antenna Mounting
The antenna must be mounted at a location such that no person(s) can come closer than 20 cm (7.9
inches) to the antenna when the transmitter is operating.
5.2 Antenna
This module is limited to operate with an antenna with maximum of 2.15 dBi nominal gain or not to
exceed 1.5 Watts ERP for any type of remotely mounted outdoor external antenna.
5.3 Labeling
The following label, visible to all persons exposed to the transmitter, must be provided on the end
product unless SAR compliance can be demonstrated:
46.00mm.
Warning: All persons must
25.40mm.
be at least 20 cm from
antenna when transmitter
operating to meet FCC RF
exposure requirements
5.4 User Manual
You must also provide the above warning in the user manual for the end product and also include the
following:
Do not substitute any antenna for the one supplied by the manufacturer. You may be exposing
person(s) to harmful radiation. contact the supplier or manufacturer for further instruction.
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
15 of 17
3.0
5.5 Mounting
Several methods are available for mounting the Expedite modem. The simplest for space constrained
applications is a pressure fit. For applications where vibration is not an issue, double sided adhesive
works well, although makes disassembly difficult. For applications where vibration is a concern, two
mounting straps are available, a surface mount soldered version (Novatel part number 649496 00233 6)
and a through – hole soldered version ( Novatel part number 649496 00232 9).
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
16 of 17
3.0
6 PACKAGING REQUIREMENTS
6.1 Shipping Packaging
Packaging shall be appropriate for the shipping method.
If the modem is to leave the ESD controlled environment, it should be packaged in an antistatic
bag.
6.2 Labeling
The modem labeling shall include:
Product Label with FCC ID, country of origin, serial number, part number, and FCC compliance
statement.
NOVATEL WIRELESS
TECHNOLOGIES LTD.
Calgary, Alberta
TITLE:
Hardware Interface Specification for
Expedite Wireless IP Modem
DOCUMENT NO.:
SHEET:
REV:
OM-01016529
17 of 17
3.0

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Creator                         : Microsoft Word
Create Date                     : 2002:01:22 15:25:23
Title                           : 020117A1.PDF
Author                          : Intermec User
Producer                        : Acrobat PDFWriter 4.0 for Windows
Modify Date                     : 2002:01:22 16:24:13-06:00
Page Count                      : 18
EXIF Metadata provided by EXIF.tools
FCC ID Filing: EHANOVCDPD

Navigation menu