Intermec Technologies RFID2450PCC-5 RF Identification Tag PCMCIA Radio User Manual 010312M1
Intermec Technologies Corporation RF Identification Tag PCMCIA Radio 010312M1
Contents
App M Card User Manual
Intermec Technologies Corporation REPORT NO: 010312-1
EMC Test Laboratory DATE: March 12, 2001
DOC. NO.: 577-500-979 Page 1 of 2
2450 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102 FCC ID: EHARFID2450PCC-5
APPENDIX M, 2450 PC Card-5 Users Manual and DoC insert
Technologies Corporation
EMC Test Laboratory
Cedar Rapids, IA
MEASUREMENT/TECHNICAL REPORT
Intermec Technologies Corporation
RF Identification (RFID) 2450 PC Card –5
2.4 GHz Spread Spectrum Transmitter
REPORT NO: 010312-1
DATE: March 12, 2001
APPENDIX M
DECLARATION OF CONFORMITY INSERT, USER INFORMATION
FOR THE 2450 PC CARD
578-100-0xx Revision A Page 1 of 1
*578-100-0xx*
*578-100-0xx*
Compliance Statement Insert
Device Name: RF Identification Radio Module Model Number: 2450 PC Card –5
FCC ID: EHARFID2450PCC-5
The responsible party for the compliance of this device is: Intermec Technologies Corporation
6001 36th Avenue West
Everett, WA 98203 USA
(425) 348-2600
This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals
approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this
product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in
the loss of the users authority to operate the equipment.
WARNING: per the FCC and Canada RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF
exposure requirements.
(2) The user shall not touch the terminal antenna and is to remain 10-cm (4 of and inches) from the antenna while the
transmitter is in use.
(3) When installing and using Intermec approved remote antennas associated the vehicle dock, a 20-cm (8-inch) passing
distance must be maintained from any body part of the user or near by persons and the remote antenna.
(4) Cables attached to the remote antennas must have a minimum length as provided from Intermec to insure the proper losses
to control RF exposure.
(5) The correct mounting for the remote antennas is fully described within the Intermec RFID 2450 PC Card Users Guide.
WARNING CANADA USERS: To prevent radio interference to the licensed service, this device is intended to be operated
indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is
subject to licensing. The end user is responsible to obtain the license.
FCC Digital Emissions Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the radio of television receiving antenna.
• Increase the separation between the computer equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
• Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.