Intermec Technologies RFID2450PCC-5 RF Identification Tag PCMCIA Radio User Manual 010312N1
Intermec Technologies Corporation RF Identification Tag PCMCIA Radio 010312N1
Contents
App N 6110 User Manual
Intermec Technologies Corporation REPORT NO: 010312-1
EMC Test Laboratory DATE: March 12, 2001
DOC. NO.: 577-500-979 Page 1 of 3
2450 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102 FCC ID: EHARFID2450PCC-5
APPENDIX N, 6110 Users Manual and DoC insert
Technologies Corporation
EMC Test Laboratory
Cedar Rapids, IA
MEASUREMENT/TECHNICAL REPORT
Intermec Technologies Corporation
RF Identification (RFID) 2450 PC Card –5
2.4 GHz Spread Spectrum Transmitter
REPORT NO: 010312-1
DATE: March 12, 2001
APPENDIX N
DECLARATION OF CONFORMITY INSERT, USER INFORMATION
FOR THE INTERMEC 6110 TERMINAL
578-100-0xx Revision A Page 1 of 2
*578-100-0xx*
*578-100-0xx*
Compliance Statement Insert
Device Name: Hand-held Computer Model Number: 6110
The responsible party for the compliance of this device is: Intermec Technologies Corporation
6001 36th Avenue West
Everett, WA 98203 USA
(425) 348-2600
CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can
result in personal injury, fire, or battery explosion.
This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals
approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this
product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in
the loss of the users authority to operate the equipment.
RIM 902 Mobitex Radio Users FCC ID: EHAWANRIM902-6100
WARNING. Per the FCC RF (radio frequency) exposure requirements:
(1) Antennas must be supplied and installed as recommended by Intermec Technologies Corporation to ensure compliance to
FCC RF exposure requirements.
(2) The user shall not touch the terminal antenna and must remain 22-mm (7/8 of and inch) from the center of the antenna
while the transceiver is in use.
(3) When installing and using Intermec approved remote antennas associated with the vehicle dock, a 23-cm (9-inch) passing
distance must be maintained from any body part of the user, or near-by persons, and the remote antenna.
(4) Cables attached to the remote antennas must have a minimum length of 183-cm (6 feet) to provide the proper losses to
control RF exposure.
(5) The correct mounting for external or remote antennas is on a ground plane (e.g., a vehicle rooftop) with the antenna
positioned such that the minimum 23-cm distance is maintained from any edge of the vehicle rooftop to the remote antenna.
RIM 802 ARDIS Radio Users FCC ID: EHAWANRIM802
WARNING: per the FCC RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF
exposure requirements.
(2) The user shall not touch the terminal antenna and is to remain 15-mm (5/8 of and inch) from the center of the antenna while
the transceiver is in use.
(3) When installing and using Intermec approved remote antennas associated the vehicle dock, a 20-cm (8-inch) passing
distance must be maintained from any body part of the user or near by persons and the remote antenna.
(4) Cables attached to the remote antennas must have a minimum length of 183-cm (6 feet) to provide the proper losses to
control RF exposure.
(5) The correct mounting for external or remote antennas would be on a ground plane (vehicle roof), and positioning the
antenna such that the minimum 20 cm is kept from any edge of the vehicle rooftop and the remote antenna.
INTERMEC RFID 2450 PC Card Radio Users FCC ID: EHARFID2450PCC-5
WARNING: per the FCC RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF
exposure requirements.
(2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antenna
while the transmitter is in use.
INTERMEC RFID 2450 PC Card Radio Users Canada ID: xxxxxxxxxx
WARNING CANADA USERS: To prevent radio interference to the licensed service, this device is intended to be operated
indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is
subject to licensing. The end user is responsible to obtain the license.
WARNING: per Canada RSS-102, RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF
exposure requirements.
(2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antenna
while the transmitter is in use.
578-100-0xx Revision A Page 2 of 2
*578-100-0xx*
*578-100-0xx*
FCC Digital Emissions Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the radio of television receiving antenna.
• Increase the separation between the computer equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
• Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Telephone Installation Warning Notices
The following notices apply to equipment that may be connected to telephone lines or systems. For your personal safety, and to protect this equipment from
potential electrical or physical damage, do NOT connect equipment to telephone lines or data communication equipment unless the following warnings have been
read, understood, and complied with.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using telephone (other than cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
• Do not use the telephone to report a gas leak in the vicinity of the leak.
Installation do téléphone : avertissements
Les avertissements qui suivent s'appliquent à tout équipement qui peut être branché aux lignes ou systemes téléphoniques. Pour votre sécurité personnelle et
pour protéger l'équipement de tout dommage électrique ou physique potentiel, NE PAS brancher un ordinateur tablette électronique ou ses périphériques aux
lignes téléphoniques ou équipements avant que les avertissements suivants aient été lus, compris et observés:
• Ne jamais installer de câblage téléphonique pendant un orage électrique.
• Ne jamais installer de prise téléphonique dans un endroit humide à moins que la prise ait été spécifiquement conçue pour être utilisée dans les endroits
humides.
Ne jamais toucher les fils de téléphone ou de l'équipement terminal non isolés à moins que la ligne téléphonique n'ait été débranchée de l'interface réseau.