Intermec Technologies RFID2450PCC-5 RF Identification Tag PCMCIA Radio User Manual 010312N1

Intermec Technologies Corporation RF Identification Tag PCMCIA Radio 010312N1

App N 6110 User Manual

Intermec Technologies Corporation REPORT NO: 010312-1EMC Test Laboratory DATE: March 12, 2001DOC. NO.: 577-500-979 Page 1 of 32450 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102 FCC ID: EHARFID2450PCC-5APPENDIX N, 6110 Users Manual and DoC insertTechnologies CorporationEMC Test LaboratoryCedar Rapids, IAMEASUREMENT/TECHNICAL REPORTIntermec Technologies CorporationRF Identification (RFID) 2450 PC Card –52.4 GHz Spread Spectrum TransmitterREPORT NO: 010312-1DATE: March 12, 2001APPENDIX NDECLARATION OF CONFORMITY INSERT, USER INFORMATIONFOR THE INTERMEC 6110 TERMINAL
578-100-0xx Revision A Page 1 of 2*578-100-0xx* *578-100-0xx*Compliance Statement InsertDevice Name: Hand-held Computer Model Number: 6110The responsible party for the compliance of this device is: Intermec Technologies Corporation6001 36th Avenue WestEverett, WA 98203 USA(425) 348-2600CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions canresult in personal injury, fire, or battery explosion.This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripheralsapproved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to thisproduct that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result inthe loss of the users authority to operate the equipment.RIM 902 Mobitex Radio Users FCC ID: EHAWANRIM902-6100WARNING. Per the FCC RF (radio frequency) exposure requirements:(1) Antennas must be supplied and installed as recommended by Intermec Technologies Corporation to ensure compliance toFCC RF exposure requirements.(2) The user shall not touch the terminal antenna and must remain 22-mm (7/8 of and inch) from the center of the antennawhile the transceiver is in use.(3) When installing and using Intermec approved remote antennas associated with the vehicle dock, a 23-cm (9-inch) passingdistance must be maintained from any body part of the user, or near-by persons, and the remote antenna.(4) Cables attached to the remote antennas must have a minimum length of 183-cm (6 feet) to provide the proper losses tocontrol RF exposure.(5) The correct mounting for external or remote antennas is on a ground plane (e.g., a vehicle rooftop) with the antennapositioned such that the minimum 23-cm distance is maintained from any edge of the vehicle rooftop to the remote antenna.RIM 802 ARDIS Radio Users FCC ID: EHAWANRIM802WARNING: per the FCC RF (radio frequency) exposure requirements,(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RFexposure requirements.(2) The user shall not touch the terminal antenna and is to remain 15-mm (5/8 of and inch) from the center of the antenna whilethe transceiver is in use.(3) When installing and using Intermec approved remote antennas associated the vehicle dock, a 20-cm (8-inch) passingdistance must be maintained from any body part of the user or near by persons and the remote antenna.(4) Cables attached to the remote antennas must have a minimum length of 183-cm (6 feet) to provide the proper losses tocontrol RF exposure.(5) The correct mounting for external or remote antennas would be on a ground plane (vehicle roof), and positioning theantenna such that the minimum 20 cm is kept from any edge of the vehicle rooftop and the remote antenna.INTERMEC RFID 2450 PC Card Radio Users FCC ID: EHARFID2450PCC-5WARNING: per the FCC RF (radio frequency) exposure requirements,(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RFexposure requirements.(2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antennawhile the transmitter is in use.INTERMEC RFID 2450 PC Card Radio Users Canada ID: xxxxxxxxxxWARNING CANADA USERS: To prevent radio interference to the licensed service, this device is intended to be operatedindoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors issubject to licensing. The end user is responsible to obtain the license.WARNING: per Canada RSS-102, RF (radio frequency) exposure requirements,(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RFexposure requirements.(2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antennawhile the transmitter is in use.
578-100-0xx Revision A Page 2 of 2*578-100-0xx* *578-100-0xx*FCC Digital Emissions ComplianceThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the radio of television receiving antenna.• Increase the separation between the computer equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.• Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Telephone Installation Warning NoticesThe following notices apply to equipment that may be connected to telephone lines or systems. For your personal safety, and to protect this equipment frompotential electrical or physical damage, do NOT connect equipment to telephone lines or data communication equipment unless the following warnings have beenread, understood, and complied with.• Never install telephone wiring during a lightning storm.• Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.• Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.• Use caution when installing or modifying telephone lines.• Avoid using telephone (other than cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.• Do not use the telephone to report a gas leak in the vicinity of the leak.Installation do téléphone : avertissementsLes avertissements qui suivent s'appliquent à tout équipement qui peut être branché aux lignes ou systemes téléphoniques. Pour votre sécurité personnelle etpour protéger l'équipement de tout dommage électrique ou physique potentiel, NE PAS brancher un ordinateur tablette électronique ou ses périphériques auxlignes téléphoniques ou équipements avant que les avertissements suivants aient été lus, compris et observés:• Ne jamais installer de câblage téléphonique pendant un orage électrique.• Ne jamais installer de prise téléphonique dans un endroit humide à moins que la prise ait été spécifiquement conçue pour être utilisée dans les endroitshumides.Ne jamais toucher les fils de téléphone ou de l'équipement terminal non isolés à moins que la ligne téléphonique n'ait été débranchée de l'interface réseau.

Navigation menu