Itron DCU5310 Mobile collection device for utility metering User Manual Hardware Installation Guide

Download:
Mirror Download [FCC.gov]
Document ID	1077895
Application ID	q98Rzot8asZZMwy1XK/2NA==
Document Description	Final Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	250.94kB (3136728 bits)
Date Submitted	2009-03-06 00:00:00
Date Available	2009-03-10 00:00:00
Creation Date	2009-03-06 17:12:30
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2009-03-06 17:12:30
Document Title	Hardware Installation Guide
Document Creator	Microsoft® Office Word 2007

Mobile Collection
Hardware Installation Guide
Identification
Mobile Collection Hardware Installation Guide
01/08/2009 TDC-0770-002
Copyright
© 2007 - 2009 Itron, Inc. All rights reserved.
Trademark Notice
Itron is a registered trademark of Itron, Inc.
All other product names and logos in this documentation are used for identification purposes only and may be trademarks or registered trademarks of their respective companies.
Suggestions
If you have comments or suggestions on how we may improve this documentation, send them to TechnicalCommunicationsManager@itron.com
If you have questions or comments about the software or hardware product, contact Itron Technical Support:
Contact
Internet: www.itron.com
E-mail: support@itron.com
Phone: 1 800 635 8725
Disclaimers
RF EXPOSURE
To comply with FCC requirements, maintain a separation distance of at least 40.0 centimetres between the antenna and all persons.
ELECTROMAGNETIC COMPATIBILITY
Use only approved accessories with this equipment. In general all cables must be high quality, shielded, correctly terminated, and normally restricted to 2 meters in length. The Mobile
Collector Lite employs special provisions to avoid radio interference and should not be altered or substituted.
Unapproved modifications or operation beyond or in conflict with these instructions for use, may void authorization by the authorities to operate the equipment.
This device has been designed to operate with the antennas listed below, and having a maximum gain of 5 dB. Antennas not included in this list or having a gain greater than 5 dB are
strictly prohibited for use with this device. The required antenna impedance is 50-ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
permitted for successful communication.
WARNING! Do not visually monitor or physically adjust the Mobile Collection
system while driving. While driving, rely on the beeps produced when meter
data is collected to indicate proper system operation. Visually monitoring or
adjusting the Mobile Collection system while driving will divert your attention
from your safe driving responsibilities. Attention to driving is your primary
responsibility, along with following all the applicable driving regulations.
Contents
Using the MC3 System .................................................................................................. 1
About the MC3 System .......................................................................................................................1
Mobile Collection Hardware Kit .................................................................................................1
Installing the MC3 System ...................................................................................................................2
About the Sled...........................................................................................................................3
About the Seat Belt Pretensioner..............................................................................................4
Installing the Junction Box ........................................................................................................5
About the Dock..........................................................................................................................6
Attaching the GoBook XR-1 to the Dock ........................................................................7
Using the PCMCIA Flash Card Adapter ...................................................................................7
Mounting the MC3 .....................................................................................................................9
Connecting the GoBook XR-1 to the MC3 ..............................................................................13
MC3 Connectors ...........................................................................................................14
Connecting the Power Cables ......................................................................................15
Connecting the Antenna ...............................................................................................18
Connecting Side-Looker Antennas ...............................................................................19
Connecting the Data Cables .........................................................................................21
Attaching Older GoBooks to the MC3 .....................................................................................23
Attaching the GoBook III to the Vehicle Dock...............................................................23
Removing the MC3 System...............................................................................................................26
Disconnecting the Cables .......................................................................................................27
Using the Mobile Collection 2.x System .................................................................... 31
About the Mobile Collection 2.x System ............................................................................................31
Mobile Collector 2.x Radio - GoBook III .......................................................................31
Mobile Collector 2.x Radio - GoBook MAX...................................................................32
Flash Card Reader ..................................................................................................................33
Compact Flash Cards .............................................................................................................33
LEDs .......................................................................................................................................33
Locking Mechanism ................................................................................................................34
Rear Connectors .....................................................................................................................34
Mobile Collector Sled ..............................................................................................................36
GoBook Mounting Systems ...............................................................................................................36
Direct Mounting Options .........................................................................................................36
Vehicle Dock / Pedestal Option ..............................................................................................37
Installing the Mobile Collection 2.x System .......................................................................................37
Attach the Mobile Collector 2.x to the Sled .............................................................................37
Connect the Antennas and Power Cables ..............................................................................39
Attach the GoBook to the Mobile Collector 2.x .......................................................................40
Attach the GoBook MAX to the Mobile Collector ..........................................................40
Attach the GoBook III to the Mobile Collector...............................................................41
Attach the GoBook MAX to the Vehicle Dock...............................................................43
Attach the GoBook III to the Vehicle Dock ...................................................................44
Connect the GoBook III Power Supply and USB Cable .........................................................44
Using the Flash Card in Mobile Collector 2.x Systems ...........................................................47
Hardware Installation Guide
iii
Contents
Insert the Flash Card ....................................................................................................47
Remove the Flash Card ................................................................................................48
Removing the Mobile Collection 2.x System .....................................................................................48
Unlock and Remove the GoBook............................................................................................49
Disconnect the Cables ............................................................................................................50
Remove the Mobile Collector from the Sled ...........................................................................50
Upgrading to a GoBook XR-1 Laptop ...............................................................................................51
Using the EkaNet System ........................................................................................... 61
EkaNet System for Mobile Demand Reset ........................................................................................61
EkaNet Compatibility .........................................................................................................................61
About the EkaNet Components .........................................................................................................62
Installing the EkaNet System ............................................................................................................63
Removing the EkaNet System ..........................................................................................................68
System Maintenance ................................................................................................... 71
RF Antenna Maintenance ..................................................................................................................71
Cleaning ..................................................................................................................................71
Replacing Gaskets ..................................................................................................................71
2.x System Maintenance ...................................................................................................................72
Inspecting and Replacing Filters .............................................................................................72
Service Bulletins ................................................................................................................................73
Mobile Collection 2.5 / GoBook III Power Plug Issue .............................................................73
Mobile Collector 2.x Power Adapter........................................................................................74
iv
Hardware Installation Guide
CHAPTER 1
Using the MC3 System
This chapter introduces you to the features, functions, and components of Mobile Collection
3.0 (MC3) system.
About the MC3 System
The MC3 is Itron's powerful, next-generation mobile collection system for electric, gas and
water providers. It offers advanced radio technology for unsurpassed performance, along
with a sophisticated mapping application utilizing GPS technology that provides a visual
indication of endpoint location.
For more information, see:
Installing the MC3 System on page 2
Removing the MC3 System on page 25
If your vehicle has a passenger-side airbag, Itron strongly recommends disabling
it when the Mobile collection system is installed. The force of the airbag deploying
could damage the laptop, radio, or other components of the system.
Mobile Collection Hardware Kit
The Mobile Collection 3.0 hardware kit contains the following items:
Hardware Installation Guide
Chapter 1
Using the MC3 System
ID
Item
MC3 radio
Description
Includes a mounting harness and straps for installing
the system in your vehicle.
USB cable
Comes attached to the dock and attaches to the
GoBook. Provides communication between GoBook
and MC3 radio.
GoBook XR-1
Runs the Mobile Collection software to collect reads.
The MC3 radio is also compatible with the GoBook III
laptop.
GoBook dock
The GoBook, power cables, and communication cables
attach to the dock.
Sled
Installs in the vehicle's passenger seat with the attached
seat belt pretensioner. Sleds are available for both the
XR-1 and GoBook III.
Not
Pictured
Cables
Connects the MC3 and GoBook dock to the junction
box.
Power junction
box
Attaches to the sled or to a pedestal mount. Provides
power to the GoBook, MC3 radio, and optional
equipment.
The junction box must be installed prior to first use. See
Installing the Junction Box on page 5 for more
information.
Omni-mount
antenna
Attaches to the top of the vehicle and receives endpoint
transmissions.
Type N to TNC
adapter
Connects older antennas to the MC3 radio.
This adapter is only needed if you are using an MC3
radio with an older omni-mount antenna (such as one
from a v2.5 system) that is already installed on your
vehicle.
The Itronix documentation refers to the laptop receptacle as a cradle; Itron uses
the term dock to identify this piece of equipment. The term dock is used repeatedly
throughout this manual; however, dock and cradle are interchangeable.
Installing the MC3 System
This chapter guides you through the installation of the Mobile Collector radio (MC3) and
GoBook XR-1 laptop computer.
Before installing these Mobile Collection system components, the procedures in the Mobile
Collector Vehicle Preparation Guide and Mobile Collector Sled and Pretensioner
Installation Guide must be completed.
Hardware Installation Guide
Installing the MC3 System
WARNING! Install the Mobile Collection system in the vehicle as
described in this document and those listed above. Failure to do so could
lead to injury or death from unsecured components during a collision.
About the Sled
The Mobile Collector sled is used to securely fasten the GoBook in the vehicle. It is placed
on the passenger seat and secured with a seat belt and pretensioner.
Watch the Mobile Collector Safety Video and read the Mobile Collector Sled
and Pretensioner Installation Guide (TDC-0708-xxx) to learn how to correctly
install the sled in your vehicle. These materials are located in a plastic sleeve
on the underside of the sled.
The sled has the GoBook dock attached to it, which serves as a locking base and also
provides power and communications to the laptop.
A power junction box ships in the Mobile Collector kit and needs to be attached to the sled.
When attached, the junction box on the sled should be facing passenger side door of the
vehicle (the junction box is attached in the example below).
Install the sled on the passenger seat before mounting the MC3 radio. The sled must be
installed with the seat belt pretensioner; see About the Seat Belt Pretensioner on page 4 for
more information.
The sled components are shown below.
ID
Item
Mobile Collector
sled
Description
Attaches to the vehicle passenger seat with the seat belt
and pretensioner system.
Junction box
Provides power to the various Mobile Collection
components. The junction box must be attached prior to
first use.
Hardware Installation Guide
Chapter 1
Using the MC3 System
ID
Item
GoBook dock
Description
Attaches to the GoBook and provides a secure base for
the laptop while in the vehicle. Docks are available for
use with both XR-1 and GoBook III models.
About the Seat Belt Pretensioner
The seat belt pretensioner makes the modern three-point safety harness in your vehicle
function similarly to an old-fashioned lap seat belt. By using the pretensioner mechanism to
cinch the mounting hardware very firmly into the junction of the seat back and the seat pad,
the pretensioner and radio mount restricts potentially hazardous equipment movement
during impact.
Modern three-point harnesses are designed to be forgiving to occupants to lessen injury. By
preventing the pay-out of seat belt webbing designed to protect people and instead using the
pretensioner to immobilize equipment, a higher degree of protection is provided in the event
of a collision.
Through standardized crash testing of the Mobile Collection system, Itron has determined
that preventing extensive rotation of the Mobile Collection equipment in a driver's side
impact reduced the stress on mechanical systems to acceptable levels. Decreasing the
amount of equipment rotation towards the driver prevents the fasteners holding the GoBook
and its dock to the sled from separating in a crash.
The seat belt pretensioner can be used in vehicles equipped with single-pass and multiplepass seat-belt tongues.
Hardware Installation Guide
Installing the MC3 System
To install the seat belt pretensioner
Follow the procedures in the Mobile Collector Sled and Pretensioner Installation
Guide (TDC-0708-xxx). A DVD showing the installation is also included with your
kit. These materials are located in a plastic sleeve on the underside of the sled.
Installing the Junction Box
The junction box takes power from the vehicle and distributes it to the MC3 radio, GoBook,
and an optional EkaNet radio (when installed).
Before you can install the MC3 system for the first time, the junction box must be installed
on either the sled or a pedestal mount.
Once installed, the junction box should remain attached to the sled or pedestal.
To install the junction box
1. Remove the junction box from the MC3 kit.
2. Locate the sled or pedestal mount on which the junction box will be installed. In the
following example, a sled is used.
3. Using a Phillips screwdriver, remove the two screws holding the junction box bracket
in place.
Hardware Installation Guide
Chapter 1
Using the MC3 System
4. Slide one end of the junction box into position over the bracket that is still attached;
be sure to orient the junction box according to the label on the sled or pedestal. The
junction box has a recessed edge that the bracket fits into.
5. Insert the other bracket (the one you removed) into the junction box, making sure that
both screw holes are visible through the bracket.
6. Insert and tighten both screws to secure the junction box to the sled or pedestal.
About the Dock
The Mobile Collector dock is used to secure the GoBook to either the sled or a pedestal
mount in your vehicle. It has connections for power and communications between the
GoBook and Mobile Collector radio.
When the XR-1 is attached, the dock must be locked to properly secure the laptop. While in
the locked state, the dock's locking mechanism extends out further from the sled than when
in the unlocked position. A green button also appears next to the locking mechanism when
the dock is locked.
To lock or unlock the dock for the XR-1, push the mechanism in, move it toward the keys
on front of the dock, and then slide it back toward its original position; the mechanism
works in a "V" pattern to lock or unlock the dock.
The examples below show the dock on a sled in the unlocked (1) and locked (2) positions,
with an XR-1 attached.
Hardware Installation Guide
Installing the MC3 System
A dock is also available for use with the GoBook III laptop; see Attaching the GoBook III
to the Vehicle Dock on page 23 for more information.
Attaching the GoBook XR-1 to the Dock
1. Make sure the dock is in the unlocked position.
2. Angle the front of the GoBook down, toward the front of the dock (where the key and
locking mechanism are). Notice the connectors and guide posts (1) near the back of
the sled base. These help ensure proper placement of the GoBook.
3. Push the back of the laptop down on to the connectors.
4. When the laptop is in place, engage the dock locking mechanism to secure the
connectors to the laptop and prevent it from moving.
5. Push the keyed mechanism in on the front of the dock to further secure the GoBook to
the dock. This helps prevent the GoBook from being stolen. (Use the supplied key to
release the lock later.)
Using the PCMCIA Flash Card Adapter
The GoBook has a PCMCIA slot that, with an adapter, you can use to read compact flash
cards.
Hardware Installation Guide
Chapter 1
Using the MC3 System
The PCMCIA slot is on the right side of the GoBook, just below the CD drive.
ID
Description
Front of GoBook XR-1
PCMCIA slot
CD drive
The compact flash card should come installed from the factory. If it is not installed or you
wish to replace cards, use the following procedures.
To insert the flash card adapter
1. Slide the flash card into the PCMCIA adapter.
2. Open the CD drive / PCMCIA slot compartment on the right-hand side of the
GoBook.
Hardware Installation Guide
Installing the MC3 System
3. Slide the adapter into the PCMCIA slot on the GoBook until it clicks into place.
To remove the flash card adapter
1. Open the CD drive / PCMCIA slot compartment on the right-hand side of the
GoBook.
2. Push the button in until the adapter pops out of the slot.
3. Pull the adapter the rest of the way out.
4. Remove the compact flash card from the adapter.
Mounting the MC3
The MC3 is mounted in a harness that can be attached to either a bucket- or bench-seat in a
vehicle. The harness contains clips on the top for mounting it on a bucket seat, and clips on
the side for bench seat mounting. The MC3 is shipped in its vehicle mount, with the straps
set up for a bucket seat. The bench straps are included in the container the MC3 was
shipped in.
Mount the sled before mounting the MC3 on the seat.
Hardware Installation Guide
Chapter 1
Using the MC3 System
If you are using a sled to secure the GoBook, be sure to mount the MC3 high enough on the
seat that the sled and laptop will fit easily beneath it. If you are using a pedestal mount, the
MC3 can be attached lower if desired.
To mount the MC3 on the seat
1.
If the MC3 radio has been removed from its harness:
Slide the radio into its harness, with the MC3 label showing through the
opening on the front of the harness.
Secure it in place by buckling the two diagonal corner straps (1).
2. Strap the mount to either the front or the back of the passenger-side seat back.
Position the unit within the mount so that when it is strapped to the seat back, the
unit's connectors face toward the passenger-side door.
10
Hardware Installation Guide
Installing the MC3 System
Sled Systems If you will be installing a sled, be sure to mount the MC3 high
enough on the seat back so that the sled and laptop will fit beneath the radio on
the seat.
Pedestal Systems If you will be attaching the GoBook to a dock on a pedestal,
the MC3 radio can be attached lower on the seat. This configuration is shown in
the following examples.
Depending on whether the vehicle has a separate passenger-side bucket seat or a
bench seat, do one of the following:
Bucket Seat Extend the mounting straps from the driver-facing side of the
vehicle mount (1), and then wrap them around the seat back and buckle them to
the opposite side of the vehicle mount (2).
Bench Seat Connect the optional bench-seat straps to the buckles on the
bottom of the vehicle mount.
Hardware Installation Guide
11
Chapter 1
Using the MC3 System
Push the free ends of the straps between the seat cushion and the seat back (1),
and then extend them up and over the top of the seat back and connect them to
the buckles on the top of the vehicle mount (2).
3. Tighten the straps until the MC3 is snug against the seat back.
12
Hardware Installation Guide
Installing the MC3 System
Connecting the GoBook XR-1 to the MC3
The MC3 rides in a harness that attaches to bucket- or bench-style passenger seat. The sled
for the GoBook XR-1 is equipped with a dock for the computer and a junction box for
power connectors (the junction box must be attached to the sled prior to use). The sled
should be mounted on the seat before the MC3 radio is attached. The MC3 must be
mounted high enough on the seat so that the right side ports on the GoBook are accessible,
as shown in the example below.
ID
Component
MC3 radio
Description
Houses components necessary for collecting
mobile reads, such as the processors,
receivers, and GPS equipment.
Laptop dock
Provides a communication link between the
GoBook and the MC3 radio. Also provides
power to the laptop.
Seat belt pretensioner
Secures the sled in the vehicle.
A properly installed sled is vital to ensure
your safety while collecting reads.
Junction box
Receives power from the vehicle and
distributes it to the MC3 radio, GoBook, and
optional equipment.
Sled
Attaches to the passenger seat of a vehicle
and secures the GoBook and dock in place.
Hardware Installation Guide
13
Chapter 1
Using the MC3 System
MC3 Connectors
The top of the MC3 radio contains the power and communications connectors, as well as a
fabric and rubber handle used to carry the radio.
The connections on the MC3 are described in the following table.
ID
Connector
Vehicle power
Description
Input that receives the connector running to the vehicle
power source to provide power to the MC3.
In addition to wiring the power cable directly to the
vehicle, a cigarette lighter power cable is available for
emergency use only. Using this cable will disable the
power management functions of the MC3 and could
adversely affect system performance. Disconnect this cable
from the power source when not in use. Failure to do so
could result in a dead battery.
Main antenna
Connector for the roof-mounted antenna cable.
Side-looker antennas Extra connectors for optional side-looking, roof-mounted
antennas.
Do not use these connectors for the main MC3 antenna.
Power indicator
An LED that turns on when the MC3 is receiving power.
A solid LED indicates the power is on and connected
to the GoBook.
A flashing LED indicates the power is on, but is not
connected to the GoBook.
14
GPS antenna
Connects the MC3 to the roof-mounted GPS antenna.
USB
Connects the GoBook to the MC3 radio.
Fuse holder
Holder accepts standard automotive 12V (15 amp) ATO
fuse (included) to protect internal circuitry from power
surges by the vehicle.
Hardware Installation Guide
Installing the MC3 System
Connecting the Power Cables
Power to the Mobile Collection components is distributed through the junction box on the
side of the sled. There are three power cables that must be connected:
Vehicle power to the junction box
Junction box to the GoBook dock
Junction box to the MC3
There is a fourth outlet on the junction box called AUX. It is for powering the EkaNet radio,
an optional device for mobile demand reset functionality.
The example below shows an MC3 radio and sled for a GoBook XR-1 with all the power
cables connected.
ID
Connection
Description
(Label)
Power in to MC3 radio Power receptacle on MC3 radio.
(POWER IN)
Power to EkaNet radio Connection from junction box to optional EkaNet radio.
Supplies power to the EkaNet radio for mobile demand
(AUX)
reset functionality.
Power out to MC3 radio Connection from junction box to MC3 radio.
(RF UNIT)
Hardware Installation Guide
15
Chapter 1
Using the MC3 System
ID
Connection
(Label)
Power in from vehicle
(POWER IN)
Power out to laptop
dock
(LAPTOP DOCK)
Description
Power source input from the vehicle's battery. This
connection is hard-wired to the vehicle battery; see the
Vehicle Preparation Guide (TDC-0382-xxx) for more
information.
Connection from junction box to the laptop dock. The
laptop dock secures the GoBook in place while you drive
a route, and provides power and communication
connections for the laptop. The dock is attached to either
a sled or pedestal mount in the vehicle (a sled is pictured
in this example).
To connect the vehicle power to the sled
Plug the vehicle power cable into the POWER IN receptacle on the junction box. Pull
the silver tab on the power cable back, insert the connector into the junction box, twist
the connector so the silver tab lines up with the labeling on the junction box, and
release the tab to lock it into place.
The other end of the power cable is hard-wired to the vehicle battery as described in
the Mobile Collection Vehicle Preparation Guide (TDC-0382-xxx).
16
Hardware Installation Guide
Installing the MC3 System
To connect power to the GoBook dock
1. Plug the red and blue end of the cable into the LAPTOP DOCK receptacle on
junction box. Pull the silver tab on the power cable back, insert the connector into the
junction box, twist the connector so the silver tab lines up with the labeling on the
junction box, and release the tab to lock it into place.
2. Plug the pigtail end into the dock connector.
Hardware Installation Guide
17
Chapter 1
Using the MC3 System
To connect power to the MC3
1. Plug one end of the cable into the RF UNIT receptacle on the junction box. Pull the
silver tab on the power cable back, insert the connector into the junction box, twist the
connector so the silver tab lines up with the labeling on the junction box, and release
the tab to lock it into place.
2. Plug the other end into the POWER IN receptacle on the MC3.
Connecting the Antenna
Next, connect the omni-mount RF antenna to the radio.
This antenna has either a fixed-base that is permanently attached to the vehicle, or a
magnetic base that can be attached to and removed from the vehicle as necessary.
18
Hardware Installation Guide
Installing the MC3 System
To connect the antenna
Connect the omni-mount RF antenna cable to the MAIN ANTENNA connector on the
MC3. Be sure to properly tighten the connector; a loose connection can lead to poor
radio and read performance.
When using older antenna cables with type N connectors along with the
MC3 radio, a type N to TNC adapter is required; this adapter is included
in the MC3 kit.
Attach the adapter securely to both the antenna cable and MC3 to ensure
optimal radio performance. Should you need another adapter or are not
able to locate the adapter in the ship kit, you will need to contact your
Itron representative or Customer Service (1.800.635.8725) to place an
order for an adapter (part number CON-0419-001).
Connecting Side-Looker Antennas
The MC3 radio supports an additional set of antennas that help gather additional reads from
endpoints located on the sides of the vehicle.
The side-looker antennas are an optional component of the MC3 system that can help
improve read coverage in certain situations (contact your Itron representative for more
information). Two additional antennas are connected to one antenna base, which is then
installed on the vehicle.
Hardware Installation Guide
19
Chapter 1
Using the MC3 System
Side-looker antennas attach to the top of the vehicle with several strong magnets. If your
vehicle has a fiberglass top, the antennas may not bond securely to the vehicle; Itron does
not recommend the use of side-looker antennas with fiberglass-topped vehicles.
To connect the side-looker antennas
1. Mount the side-looker antennas (2) on top of the vehicle, two feet in front of or behind
the primary RF omni-mount antenna (1).
2. Route the antenna cables into the vehicle.
20
Hardware Installation Guide
Installing the MC3 System
3. Remove the caps covering the side-looker antenna ports, identified by R and L on the
MC3 radio in the vehicle.
4. Connect the side-looker antenna cables to the R and L antenna inputs on the MC3
radio.
Connecting the Data Cables
There are two communications cables for receiving and transferring GPS and meter data
between MC3 and the GoBook:
A USB cable from the GoBook dock to the MC3
A serial cable from the EkaNet radio to the GoBook dock (only for electric meter
mobile demand reset).
Hardware Installation Guide
21
Chapter 1
Using the MC3 System
The following picture shows a Mobile Collection system with all the data cables connected.
ID
Connection
Description
(Label)
RF radio antenna
RF radio antenna connection on MC3 radio. Receives
(MAIN ANTENNA) endpoint signals.
GPS antenna
(GPS)
USB data cable
(USB)
USB data cable
GPS antenna connection to MC3 radio. Receives GPS
signal for vehicle location and tracking.
USB data output from MC3 radio. Data is transferred from
the radio to the laptop through this cable.
USB data input on the laptop dock. Data from the MC3
radio is transferred to the Mobile Collection software
running on the laptop.
Serial cable to EkaNet Serial port connection from the laptop dock to an optional
EkaNet radio. The cable transfers data from EkaNet
equipped endpoints to the laptop for mobile demand reset
functionality.
To connect the USB data cable
1. Ensure that the rectangular end of the USB cable (1) is inserted into the GoBook dock
USB port.
22
Hardware Installation Guide
Installing the MC3 System
The USB cable is connected to the dock at the factory and is secured with a cable
tie. DO NOT remove this cable tie or unplug the USB cable from the dock. The
cable tie helps ensure a secure connection and should never be disconnected. The
cable tie also ensures that the correct COM port is used for GPS communications
with the Mobile Interface software. Using a different USB port will prevent the
MC3 radio from communicating properly with the software.
2. Plug the round end of the USB cable into the MC3 radio by pulling the connector
sleeve back, plugging the connector in to the receptacle, and releasing the sleeve.
Attaching Older GoBooks to the MC3
This section explains how to connect older GoBook models to the MC3.
GoBook III This GoBook can be attached directly to the vehicle dock, mounted on a
pedestal by the driver or on a sled (similar to the GoBook XR-1).
GoBook MAX This GoBook must be attached to the vehicle dock on a pedestal
mount; no sled option is available.
Attaching the GoBook III to the Vehicle Dock
You can attach the GoBook III to a vehicle dock on a sled or pedestal near the driver. The
vehicle dock must be installed on the sled or pedestal before attaching the GoBook III.
Refer to the Itronix Vehicle Cradle Installation Guide for detailed instructions.
Hardware Installation Guide
23
Chapter 1
Using the MC3 System
The Itronix documentation refers to the laptop receptacle as a cradle; Itron uses
the term dock to identify this piece of equipment. The term dock is used repeatedly
throughout this manual; however, dock and cradle are interchangeable.
To attach the GoBook III to the vehicle dock
1. Ensure that the vehicle dock is in the unlocked position. When locked, a steel pin (1)
is visible on the top of the vehicle dock; this pin helps secure the GoBook III in place.
When unlocked, this pin is not visible. The front (2) and rear (3) mounting guides are
also extended out to the perimeter of the dock when unlocked.
To unlock the dock, push in underneath the locking mechanism (1) and then
pull the handle out (2) as shown.
2. Lower the GoBook III onto the vehicle dock, making sure that the two rear locking
mechanisms on the top of the vehicle dock fit into the mating holes on the GoBook
underside.
24
Hardware Installation Guide
Installing the MC3 System
3. Once the GoBook is properly aligned on the vehicle dock, push the locking
mechanism in (1) to secure it. This locks the pin in place on the underside of the
GoBook and also engages the mounting guides.
4. One end of the USB data cable comes attached to the vehicle dock; attach the other
end to the USB port on the MC3.
The USB cable is connected to the dock at the factory and is secured with
a cable tie. DO NOT remove this cable tie or unplug the USB cable from
the dock. The cable tie helps ensure a secure connection and should never
be disconnected. The cable tie also ensures that the correct COM port is
used for GPS communications with the Mobile Interface software. Using
a different USB port will prevent the MC3 radio from communicating
properly with the software.
5. Connect the antennas and power cables for the MC3 as described earlier in this
document.
Hardware Installation Guide
25
Chapter 1
Using the MC3 System
Removing the MC3 System
At some point, you may need to remove the Mobile Collection system from the vehicle.
Before removing any Mobile Collection system components, be sure to
stop the Mobile Interface software, shut down the GoBook, and turn off
the vehicle power. See the Mobile Collection User's Guide (TDC-0380xxx) for more information.
To remove the GoBook from the vehicle dock
1. Stop processing reads.
2. Complete routes.
3. Export routes.
4. Shut down all open applications and then shut down the GoBook.
CAUTION If you accidently disconnect the GoBook from the MC3
radio before shutting down Windows and the laptop, the following
message appears:
Unsafe Removal of Device
Before clicking OK, clear the ShowUnplug/Eject icon on the Taskbar
box. If you do not clear this box, you will not be able to properly shut
down the system in the future.
5. Close the GoBook screen.
6. Turn off the vehicle.
7. Disconnect any cables attached directly to the GoBook.
8. If unlocking the GoBook from the vehicle cradle:
26
Hardware Installation Guide
Removing the MC3 System
GoBook XR-1 Push the locking mechanism in and slide it toward the keys on
front of the dock (1), and then push it in a little further and pull it back to the
starting position to unlock the dock (2).
GoBook III Push in underneath the locking mechanism (1) and then pull the
handle out (2) as shown.
9. Gently lift the GoBook up and away from the cradle.
Disconnecting the Cables
Disconnect the cables from the MC3 and leave them in the vehicle for the next installation
of the system.
To disconnect the cables
1. Complete the procedure To remove the GoBook from the vehicle dock on page 26.
2. Unplug the cables from the MC3 radio.
3. Unplug all the cables from the GoBook dock EXCEPT for:
Hardware Installation Guide
27
Chapter 1
Using the MC3 System
The USB cable (both XR-1 and GoBookIII docks).
The power cable that is hard-wired to the dock for GoBookIII installations.
4. Unplug the cables from the sled or pedestal junction box.
5. Release the mounting clips on the MC3 harness and remove the MC3 radio.
6. Unbuckle the seat belt securing the sled to the passenger seat and remove the sled
from the vehicle. Leave the pretenstioner attached to the seat belt.
28
Hardware Installation Guide
Removing the MC3 System
Hardware Installation Guide
29
CHAPTER 2
Using the Mobile Collection 2.x System
This chapter describes how to install and use legacy versions of the Mobile Collector radio.
If your vehicle has a passenger-side airbag, Itron strongly recommends disabling
it when the Mobile collection system is installed. The force of the airbag deploying
could damage the laptop, radio, or other components of the system.
About the Mobile Collection 2.x System
The Mobile Collector 2.x radio houses the transmitter, receivers, and other electronics
required to communicate with endpoints.
There are two versions of the Mobile Collector radio; one for use with the GoBook MAX
and one for use with the GoBook III. Both versions contain the same features and
functionality, but may look slightly different, depending on the version of GoBook you are
using.
Mobile Collector 2.x Radio - GoBook III
ID
Component
USB cable clip
Hardware Installation Guide
Description
Secures the USB cable that connects the GoBook
III to the Mobile Collector radio. The cable clip
prevents the USB cable from coming loose while
driving a route.
31
Chapter 2
Using the Mobile Collection 2.x System
ID
Component
Mounting guides
Description
Hold the GoBook in place, and assist you in
placing the GoBook on the radio in the proper
location.
Flash card reader
Provides data backups when configured through
the Mobile Administration function.
LEDs
Indicate system power, operation, and flash card
status.
Locking mechanism
Secures the GoBook to the top of the radio.
Screen rests
Provide support for the GoBook III screen.
Mobile Collector 2.x Radio - GoBook MAX
32
ID
Component
Mounting guides
Description
Hold the GoBook in place, and assist you in
placing the GoBook on the radio in the proper
location.
Flash card reader
Provides data backups when configured through
the Mobile Administration function.
LEDs
Indicate system power, operation, and flash card
status.
Locking mechanism
Secures the GoBook to the top of the radio.
Screen rest
Provides support for the GoBook MAX screen.
Hardware Installation Guide
About the Mobile Collection 2.x System
Flash Card Reader
Route data can be transferred to and from the Mobile Collector using a removable flash card
(two CompactFlash® cards are supplied). The Windows operating system on the GoBook
recognizes the flash card as a removable drive, allowing standard file access.
Periodic data backups to the flash card can be configured in the Mobile Administration
application; see the Mobile Collection Administration Guide (TDC-0381-001) or Online
Help for more information.
See the Mobile Collection User's Guide (TDC-0380-xxx) or Online Help for more
information on using the flash card in day-to-day activities.
Compact Flash Cards
The Mobile Collection system includes two SanDisk CompactFlash cards. If you require
more cards, you may purchase them through Itron or through electronics stores or
distributors.
Use of unapproved cards can result in loss of data.
If you purchase additional cards from a distributor or electronics retailer, Itron recommends
the following:
64M SanDisk Industrial Grade, Extended Temperature range
64M Hitachi Renesas, Industrial Grade, Wide Temperature, or Extended Temperature
range
LEDs
Three LEDs signal system power, system operation, and flash card status. Errors relating to
the transmitter and receivers display on the GoBook within the Mobile Interface.
The table below describes the LED status indicators.
LED
Power/Error 1
Operate/Error 2
Hardware Installation Guide
Color
Red
Description
Voltage error condition
Flashing Green
Vehicle accessories power on, ignition off
Green
Vehicle ignition on
None
System is shutting down or completely off
Red
Temperature error condition
33
Chapter 2
Using the Mobile Collection 2.x System
LED
Flash Card
Color
Green
Description
Operating normally
None
System is shutting down or completely off
Red
Data transferring to/from the flash card
reader
None
System is shutting down or completely off
Locking Mechanism
The locking mechanism attaches the GoBook to the Mobile Collector. Locking the GoBook
to the Mobile Collector reduces the likelihood of the GoBook separating from the Mobile
Collector in the event of a collision.
The GoBook MAX has a keyed locking mechanism; the GoBook III has a keyless locking
mechanism.
WARNING! Do not set down the Mobile Collector on its front face while
carrying it by the handle or at any time. Doing so may damage the flash card
reader or the flash card, or may break off the key if it was left in the mounting
lock.
Rear Connectors
The rear of the Mobile Collector 2.x radio contains the power and communications
connectors.
34
Hardware Installation Guide
About the Mobile Collection 2.x System
ID
Connector
RF antenna
Description
Connects to the roof-mounted antenna. See the
Mobile Collection Vehicle Preparation Guide.
Itron provides a magnetic mount option for the
RF antenna. This magnetic mount is intended as
a temporary solution and it is for emergency use
only. Long-term use of a magnetic mount
antenna could adversely affect system
performance and is not a supported configuration
of this product.
GPS antenna
Connects to the externally-mounted GPS
antenna. This gold-plated connector is used with
the optional Mapping feature of the Mobile
Interface software.
USB
Connects the GoBook III computer to the radio
for data transfer.
Also for use with a GoBook computer not
mounted directly to the Mobile Collector radio.
See Vehicle Dock / Pedestal Option on page 37
for more information.
Mobile Collector radios for use with the GoBook
MAX have a USB data connection built into the
radio lid.
GPS receiver
Connects to an external GPS receiver box when
using a version 2.0 radio.
Version 2.5 radios have a GPS receiver built into
the Mobile Collector, so this connector is not
used with a 2.5 radio.
GoBook III power
Provides power to the GoBook III laptop.
Mobile Collector radios for use with the GoBook
MAX have a power connection built into the
radio lid.
Power in
Receives power from the vehicle and distributes
it to the radio and GoBook.
In addition to wiring the power cable directly to
the vehicle, a cigarette lighter power cable is
available for emergency use only. Using this
cable will disable the power management
functions of your Mobile Collector and could
adversely affect system performance.
ALWAYS disconnect this cable from the power
source when not in use. Failure to do so could
result in a dead vehicle battery.
Fuse holder and fuse
Hardware Installation Guide
Provides over-current protection for the radio.
Holder accepts standard automotive 12V (15
amp) ATO fuse (included) to protect internal
circuitry from power surges by the vehicle.
35
Chapter 2
Using the Mobile Collection 2.x System
Mobile Collector Sled
The Mobile Collector sled is a mounting bracket designed to secure the Mobile Collector
radio in the vehicle and support it and the GoBook in an upright position on the passenger
seat.
GoBook Mounting Systems
There are two mounting options for the GoBook:
Direct Mount Option The GoBook mounts directly on the Mobile Collector.
Vehicle Dock / Pedestal Option The GoBook mounts remotely on a free-standing
pedestal, using the Itronix vehicle cradle.
The Itronix documentation refers to the laptop receptacle as a cradle; Itron uses
the term dock to identify this piece of equipment. The term dock is used repeatedly
throughout this manual; however, dock and cradle are interchangeable.
WARNING! Improperly installed or secured components may
result in injury or death in the event of a collision. Install and secure
the system components in accordance with this document, the
Mobile Collection Vehicle Preparation Guide, the Mobile Collection
Sled and Pretensioner Installation Guide, manufacturer installation
instructions, and applicable safety standards.
Direct Mounting Options
The GoBook communicates with the Mobile Collector and receives power from it through
the mounting connector, providing fast, easy docking and removal, without additional
cables.
36
Hardware Installation Guide
Installing the Mobile Collection 2.x System
The GoBook MAX mounts onto the Mobile Collector radio within the mounting guides so
that the mounting connector and the external modem connector insert into mating
connectors on the underside of the GoBook. A key inserted into the locking mechanism
turns clockwise to lock the GoBook in place.
The GoBook III mounts onto the Mobile Collector radio within the mounting guides, but
communicates through a USB cable and is powered from a cable connected to the Mobile
Collector.
Vehicle Dock / Pedestal Option
Optionally, you may mount the GoBook on a vehicle cradle that is attached to a pedestal.
This option allows you to position the Mobile Collector in the vehicle so that it is closer to
the driver, while placing the Mobile Collector and its base elsewhere in the vehicle. A key
inserted into the locking mechanism turns clockwise to lock the GoBook MAX in place; a
similar mechanism will be available for use with the GoBook III.
Installing the Mobile Collection 2.x System
This section shows you how to properly install a Mobile Collection 2.x system, with either a
GoBook III or a GoBook MAX.
Attach the Mobile Collector 2.x to the Sled
A plate installed on the underside of the Mobile Collector contains holes and slots that mate
with the pins on top of the sled. Attach the Mobile Collector to the sled by lowering it onto
the pins and rotating it so that the pins slide into the slots, locking the Mobile Collector in
place.
To attach the Mobile Collector to the Sled
1. Hold the Mobile Collector over the base and orient it so that the right rear corner faces
the passenger door.
Hardware Installation Guide
37
Chapter 2
Using the Mobile Collection 2.x System
2. Lower the Mobile Collector onto the sled and gently move it around until the center
pin on the base snaps into the center hole on the underside of the Mobile Collector.
3. While gently applying downward pressure, rotate the collector back and forth slightly
until the three pins on the base fit into the three matching holes on the underside of the
Mobile Collector.
4. Grip two corners of the Mobile Collector that are opposite each other diagonally and
rotate it counter-clockwise until you hear the locking pin snap into the underside of
the Mobile Collector.
38
Hardware Installation Guide
Installing the Mobile Collection 2.x System
When finished, the rear of the Mobile Collector should be flush with the side of the
base and its rear connectors should face the passenger door.
Connect the Antennas and Power Cables
The RF antenna, GPS antenna, and Mobile Collector power cable should be pre-installed in
the vehicle and routed to where the Mobile Collector will be installed.
The GPS system for version 2.x Mobile Collectors is an optional component that
is part of the Mapping system. If your installation does not include Mapping,
simply attach the RF antenna and the power cable in the procedure below; ignore
the steps related to the GPS antenna.
This section shows you how to connect the antennas and the power cable to the rear of the
Mobile Collector radio.
To connect the antennas and power cables
1. Plug the power cable (1) into the power connector on the Mobile Collector.
2. Attach the pre-wired RF antenna cable (2) and turn the knurled part of the antenna
cable clockwise until the cable is firmly attached.
Hardware Installation Guide
39
Chapter 2
Using the Mobile Collection 2.x System
If the power cable does not reach the Mobile Collector, use the optional extension
cable to extend the length (extension cables may be purchased from Itron). Plug
the power cable into one end of the extension cable and plug the other end of the
extension cable in to the Mobile Collector. Be sure both ends snap into their
respective connectors.
3. Attach the GPS cable to the connector. Both the end of the cable and the connector are
gold-plated for easy identification.
Attach the GoBook to the Mobile Collector 2.x
This section shows you how to connect both the GoBook MAX and GoBook III to the
Mobile Collector radio. The GoBook may be either attached directly to the Mobile
Collector radio or attached to a vehicle cradle mounted on a pedestal by the driver (for more
information, see GoBook Mounting Systems on page 36).
To attach the GoBook to the Mobile Collector, follow the steps in one of the following
sections:
GoBook MAX Procedures
Attach the GoBook MAX to the Mobile
Collector on page 40
GoBook III Procedures
Attach the GoBook III to the Mobile
Collector on page 41
Attach the GoBook MAX to the Vehicle Attach the GoBook III to the Vehicle
Dock on page 43
Dock on page 44
Attach the GoBook MAX to the Mobile Collector
Follow these steps to mount the GoBook MAX onto the Mobile Collector.
Before attempting to mount the GoBook onto the Mobile Collector, be sure to
unlock the locking mechanism.
To attach the GoBook MAX to the Mobile Collector
1. From the driver’s side of the vehicle, align the GoBook MAX with the four mounting
guides on top of the Mobile Collector.
40
Hardware Installation Guide
Installing the Mobile Collection 2.x System
2. Angle the top of the GoBook MAX towards the passenger door, as shown below, and
lower it so that the two rear connectors (1) on the Mobile Collector top fit into the
mating holes on the GoBook MAX underside.
3. Lower the GoBook MAX onto the Mobile Collector within the mounting guides (2)
until the underside of the GoBook MAX is flush with the top of the Mobile Collector.
If necessary, gently move the GoBook MAX slightly from side to side to ensure the
connectors on top of the Mobile Collector mate with those on the underside of the
GoBook MAX.
4. Insert the key into the mounting lock and press the locking mechanism so it engages
the GoBook MAX.
5. Turn the key clockwise to lock the GoBook MAX in place.
6. Remove the key from the lock so that it is not stolen or accidently broken.
7. Lift the GoBook MAX screen up and gently push it back so that it rests on the Mobile
Collector screen rest.
Attach the GoBook III to the Mobile Collector
Follow these steps to mount the GoBook III onto the Mobile Collector.
Hardware Installation Guide
41
Chapter 2
Using the Mobile Collection 2.x System
To attach the GoBook III to the Mobile Collector
1. From the driver’s side of the vehicle, align the GoBook III with the two mounting
guides (1) on top of the Mobile Collector.
2. Angle the GoBook III towards the passenger door, as shown below, and slide it under
the mounting guides (1) toward the back of the Mobile Collector.
3. Lower the GoBook III onto the Mobile Collector within the mounting guides until the
underside of the GoBook III is flush with the top of the Mobile Collector.
If necessary, gently move the GoBook III slightly from side to side to ensure the
connectors on top of the Mobile Collector mate with those on the underside of the
GoBook III.
4. With one hand, pull on the locking mechanism to release it. With the other hand,
gently push down on the top of the GoBook III, as shown below.
5. Release the locking mechanism to lock the GoBook III in place.
6. Attach the necessary USB and power cables from the Mobile Collector to the GoBook
III.
7. Secure the USB cable in place by tightening the metal cable clip.
42
Hardware Installation Guide
Installing the Mobile Collection 2.x System
8. Lift the GoBook III screen up and gently push it back so that it rests on the Mobile
Collector screen rest.
Attach the GoBook MAX to the Vehicle Dock
As part of an optional remote installation, you may attach the GoBook MAX to a vehicle
dock on a pedestal near the driver. The vehicle dock should be pre-installed. Refer to the
Itronix Vehicle Cradle Installation Guide for detailed instructions.
The Itronix documentation refers to the laptop receptacle as a cradle; Itron uses
the term dock to identify this piece of equipment. The term dock is used repeatedly
throughout this manual; however, dock and cradle are interchangeable.
To attach the GoBook MAX to the vehicle dock
1. Angle the top of the GoBook MAX and center on the vehicle dock mounting guides,
then lower it so that the two rear locking mechanisms on the vehicle dock top fit into
the mating holes on the GoBook MAX underside.
2. Lower the GoBook MAX onto the vehicle dock within the mounting guides until the
underside of the GoBook MAX is flush with the top of the vehicle dock.
3. Insert the key into the mounting lock.
4. Press the locking mechanism so it engages the GoBook MAX.
5. Turn the key clockwise to lock the GoBook MAX in place.
Remove the key from the lock so that it is not accidently broken or stolen.
6. Plug the vehicle dock cable into a vehicle dock USB port. Two USB ports are located
on the back of the vehicle dock.
7. Plug the vehicle dock cable into the Mobile Collector radio by pulling the SMA
connector sleeve back, plugging the connector in to the Mobile Collector as shown,
and releasing the sleeve.
Hardware Installation Guide
43
Chapter 2
Using the Mobile Collection 2.x System
Attach the GoBook III to the Vehicle Dock
As part of an optional remote installation, you may attach the GoBook III to a vehicle cradle
on a pedestal near the driver. The vehicle cradle should be pre-installed. Refer to the Itronix
Vehicle Cradle Installation Guide for detailed instructions.
To attach the GoBook III to the vehicle dock
1. Lower the GoBook III onto the vehicle dock. Be sure to align it within the front and
read guides on the dock. The front of the laptop should face the locking mechanism on
the front of the dock.
2. Push in the handle on the front of the dock to engage the locking mechanism and
secure the GoBook to the dock.
3. Push in the keyed part of the locking mechanism to further lock it and prevent theft of
the GoBook.
4. Plug one end of the USB cable into one of the two available ports on the back of the
vehicle dock. The port uses a standard USB connector.
5. Plug the vehicle dock USB cable into the USB port on the Mobile Collector by pulling
the SMA connector sleeve back, plugging the connector in to the Mobile Collector,
and releasing the sleeve. This port uses an SMA connector.
Connect the GoBook III Power Supply and USB Cable
The GoBook III receives power from the Mobile Collector radio itself, through a simple
power cable connection. In versions of the Mobile Collection system that use a GoBook
MAX, the power and data connections are integrated into the top of the Mobile Collector
radio.
For the GoBook III, additional cables must be attached to provide the laptop with power and
a data connection. The USB cable is used to provide data collected by the Mobile Collector
radio to the Mobile Interface application running on the GoBook III.
44
Hardware Installation Guide
Installing the Mobile Collection 2.x System
To connect the GoBook III power supply and USB cable
1. Attach the end of the GoBook III power cable (1) to the blue connector on the back of
the Mobile Collector radio (2); this connector is located beneath the main power
supply.
2. Attach the other end of the power cable to the connector on the back of the GoBook
III.
Hardware Installation Guide
45
Chapter 2
Using the Mobile Collection 2.x System
3. Plug the USB cable into the Mobile Collector radio by pulling the SMA connector
sleeve back, plugging the connector in to the Mobile Collector as shown, and
releasing the sleeve.
4. Connect the USB cable to the back of the GoBook III as shown below.
5. Route the USB cable through the channel on the back of the Mobile Collector radio
mounting guide. Press the cable down into the channel to make sure it is secure.
46
Hardware Installation Guide
Installing the Mobile Collection 2.x System
This ensures data communication between the GoBook III and the Mobile Collector
radio while you are driving a route.
Using the Flash Card in Mobile Collector 2.x Systems
You can import route files to the Mobile Interface database and export the collected data
using a removable flash card in the Mobile Collector flash card reader.
The default drive letter for the flash card reader will vary, depending
on the type of GoBook used in your system configuration.
GoBook MAX When using the GoBook MAX, the card reader
defaults to drive F:.
GoBook III When using the GoBook III (which may include an
optional 3-slot external reader), the card reader can be any of the
following drives: G:, H:, and I:. The actual letter used will vary
depending on when various peripherals are connected to the
system. Always ensure you are accessing the proper drive.
Insert the Flash Card
Follow these steps to insert the flash card.
WARNING! If you do not hold the flash card correctly, the flash
card will not insert into the reader. Forcing the flash card into the
reader may damage the reader by bending the connector pins.
Hardware Installation Guide
47
Chapter 2
Using the Mobile Collection 2.x System
To insert the flash card
1. Hold the flash card as shown to insert it into the Mobile Collector Flash Card Reader.
2. Insert the card in the flash card reader slot and press it in until it is firmly in place and
the eject button pops out.
Remove the Flash Card
Follow these steps to remove the flash card.
Before removing the flash card, shut down the GoBook. Failure to do so could
result in data loss on your flash card.
To remove the flash card
1. Shut down the GoBook.
2. Press the eject button on the flash card reader.
3. Gently pull the flash card out of the flash card reader slot.
Removing the Mobile Collection 2.x System
At some point, you may need to remove the Mobile Collection system from the vehicle.
Perform the following tasks to remove the Mobile Collection system.
48
Hardware Installation Guide
Removing the Mobile Collection 2.x System
Before removing any Mobile Collection system components be sure to stop the
Mobile Interface and shut down the GoBook.
Unlock and Remove the GoBook
Follow these steps to remove the GoBook from the Mobile Collector or vehicle cradle. The
following procedure can be used with either the GoBook MAX or GoBook III.
To unlock and remove the GoBook
1. Shut down any open applications and then shut down the GoBook.
2. Close the GoBook screen.
3. Disengage the GoBook locking mechanism:
GoBook MAX Insert the key in the locking mechanism and turn it counterclockwise. Pull the key and the mounting lock towards you so the locking
mechanism is disengaged from the GoBook.
-> If unlocking the GoBook MAX from the vehicle cradle, push in underneath
the locking mechanism and then pull the mechanism out.
Hardware Installation Guide
49
Chapter 2
Using the Mobile Collection 2.x System
GoBook III Disconnect any cables from the back of the GoBook III. Pull the
locking mechanism out, away from the GoBook III.
-> If unlocking the GoBook III from the vehicle dock, push up and in on the
underside of the locking mechanism, and then pull the mechanism out to release
it.
4. Gently lift the GoBook up and away from the Mobile Collector radio or vehicle dock.
CAUTION If you accidently disconnect the GoBook from the MC3
radio before shutting down Windows, the following message appears:
Unsafe Removal of Device
Before clicking OK, clear the ShowUnplug/Eject icon on the Taskbar
box. If you do not clear this box, you will not be able to properly shut
down the system in the future.
Disconnect the Cables
Unplug the cables from the Mobile Collector and leave them for the next installation of a
Mobile Collection system, if desired.
To disconnect the cables
1. Complete Unlock and Remove the GoBook on page 49.
2. Unplug the cables from the Mobile Collector. This includes the USB cable, power
cable, and any antenna cables.
Remove the Mobile Collector from the Sled
When you attached the Mobile Collector to the sled, a locking pin snapped into the
underside of the Mobile Collector. To remove the Mobile Collector, you must reach
underneath the top of the sled and pull down on the locking pin while rotating the Mobile
Collector slightly.
50
Hardware Installation Guide
Upgrading to a GoBook XR-1 Laptop
To remove the Mobile Collector from the sled
1. From the passenger side of the vehicle, reach underneath the top of the base and locate
the locking pin knob.
2. Use one hand to pull the knob down, and use the other hand to push a corner of the
Mobile Collector in a clockwise direction.
3. Continue pulling the knob down and pushing until the pin can no longer snap into the
underside of the Mobile Collector.
4. Grip two corners of the Mobile Collector that are opposite each other diagonally and
rotate it clockwise until you cannot rotate it further.
The right rear corner of the Mobile Collector faces the passenger-side door when the
Mobile Collector cannot be rotated further.
5. Lift the Mobile Collector off the base.
6. Unfasten the seat belt and pretensioner and lift the base off the seat.
Upgrading to a GoBook XR-1 Laptop
If you are upgrading from a GoBook MAX or GoBook III laptop that was originally
mounted on top of the MC2.5 Radio to a GoBook XR-1 laptop that is mounted on a
pedestal, use the following instructions. The MC2.5 radio remains mounted on the existing
sled.
Note Before you begin, keep in mind that the MC2.5 Radio will remain the same.
The MC2.5 Radio will still be mounted on the sled, and all the cabling will not
change.
The XR-1 laptop upgrade kit contains the following items:
Hardware Installation Guide
51
Chapter 2
Using the Mobile Collection 2.x System
GoBook XR-1 laptop
Vehicle docking station
Pedestal mounting bracket; pedestal not included
Power distribution box; small box with the Itron logo
Cables to connect the MC2.5 Radio to the XR-1 docking station and power
distribution box (CBA-0269-001, CBA-0332-002, and CBA-0187-004)
Peripherals (not pictured): Screen cloth and the USB flash drive
To Install the Pedestal Mount
1. Install the pedestal mount between the driver and passenger seats.
52
Hardware Installation Guide
Upgrading to a GoBook XR-1 Laptop
2. Place the mount and brackets for the power distribution box in the middle of
the pedestal. Tighten securely.
3. Remove the two screws in the top mounting bracket.
Top mounting bracket and screws
4. Position the distribution box against the bottom bracket.
Hardware Installation Guide
53
Chapter 2
Using the Mobile Collection 2.x System
5. Place the top bracket on the power distribution box and screw the top mounting
bracket back in.
To Connect the Dock to the Pedestal Mount:
Place the vehicle dock onto the pedestal mount and securely tighten.
54
Hardware Installation Guide
Upgrading to a GoBook XR-1 Laptop
To Mount the XR-1 GoBook to the Docking Station
1. When positioning the XR-1 GoBook onto the dock, put the front end in first.
2. Make sure that the holding bracket is snug against the front and press down on the
laptop.
3. Push the locking lever in and to the right to secure the laptop on the dock.
Locked
Hardware Installation Guide
Unlocked
55
Chapter 2
Using the Mobile Collection 2.x System
To Connect to the Power Distribution Box:
1. Use the existing power cable and connect into the Power In slot.
2. Use the CBA-0269-001 cable to connect the power distribution box to the RF unit in
the RF Unit slot.
56
Hardware Installation Guide
Upgrading to a GoBook XR-1 Laptop
3. Use the CBA-0332-002 cable to connect the power distribution box to the
dock in the Laptop Dock slot.
vehicle
When you are finished, the power distribution box should look like the example
below.
Hardware Installation Guide
57
Chapter 2
Using the Mobile Collection 2.x System
Connecting to the Vehicle Dock
1. Connect the other end of CBA-0332-002 cable to the vehicle dock. This is the
smallest of the three cables.
2. Connect the other end of the CBA-0187-004 cable. This cable will come pre-wired to
the vehicle dock with a clip to hold the cable in place.
Take the other end of the CBA-0187-004 cable and connect it to the RF unit.
58
Hardware Installation Guide
Upgrading to a GoBook XR-1 Laptop
When you have completed the installation, your hardware should look like the example
below.
Hardware Installation Guide
59
CHAPTER 3
Using the EkaNet System
The EkaNetTM system is an optional component that can be used with the Mobile Collection
system. An additional antenna and radio are used to communicate with Eka-equipped
endpoints in the field to enable mobile demand reset functionality.
This chapter shows you how to install the EkaNet hardware components in a
vehicle and then connect them to the Mobile Collection system. In order to use the
mobile demand functionality in the Mobile Interface, a separate software
installation must be performed on the GoBook. See your system administrator for
more information.
EkaNet System for Mobile Demand Reset
The EkaNet radio is only required if you are using Itron Advanced Drive-by AMR (mobile
demand reset) for electric meters. It is ordered separately from the Itron Mobile Collection
system.
WARNING! Keep at least two feet away from the EkaNet antenna when it is
transmitting.
The EkaNet antenna should be at least four feet away from the regular Mobile Collection
RF antenna to prevent interference.
For more information about the EkaNet system, see the:
EkaNet Mobile Collector Hardware Installation Manual (document number
10250)
EkaNet Mobile Collection Software Manual (document number 10223)
By default, these documents are stored in the following location:
C:\Program Files\Eka\EkaNet Mobile\doc
EkaNet Compatibility
The following table lists the versions of Mobile Collection hardware (radio and laptop) that
are compatible with the EkaNet system.
Mobile Collection v3.0 software is required for the EkaNet system. Although
older versions of hardware can support the system, you must use v3.0 software.
Laptop
GoBook MAX
Hardware Installation Guide
Radio Version
2.0
EkaNet Compatible?
No
61
Chapter 3
Using the EkaNet System
Laptop
GoBook MAX
Radio Version
MC3
EkaNet Compatible?
No
GoBook III
2.5
Yes
GoBook III
MC3
Yes
GoBook XR-1
2.5
Yes
GoBook XR-1
MC3
Yes
About the EkaNet Components
The following components are a part of the optional EkaNet system. These components
need to be installed in the vehicle.
ID
Item
EkaNet radio
Description
Routes data received by the antenna to the laptop
running the Mobile Interface software, with EkaNet
software enabled.
Radio pouch
Secures the radio in the vehicle. The pouch connects to
the MC3 radio harness.
EkaNet antenna
Receives data from Eka-enabled endpoints in the field.
The antenna should be installed 4 feet away from the
main Mobile Collection RF antenna.
* Not
Pictured
Cables
A power cable from the Mobile Collection junction box
supplies the radio with power.
A serial cable from the radio to the laptop transfers
data.
62
Hardware Installation Guide
Installing the EkaNet System
Installing the EkaNet System
Follow the steps below to connect the EkaNet system.
To connect the EkaNet system
1. Attach the external EkaNet antenna to the top of the vehicle. It should be placed at
least four (4) feet away from the main Mobile Collector RF antenna to prevent
interference.
This antenna uses a powerful magnet to attach to the vehicle.
2.
Using a magnetic-mount antenna on a fiberglass-roofed vehicle is not
recommended. The antenna may come loose during transit and be damaged. It
could also be a hazard to others if it falls of the roof of a moving vehicle.
Hardware Installation Guide
63
Chapter 3
Using the EkaNet System
3.
Insert the EkaNet radio (1) into the pouch (2). The antenna connector (3) must face
the top of the pouch.
4. Close the pouch flap over the radio and snap it shut to secure the EkaNet radio.
5. Clip the EkaNet pouch to a harness strap on the back of the seat where the Mobile
Collection system is installed.
If you are using an MC3 system, clip the pouch to one of the straps that secure
the MC3 radio to the seat. This setup is shown in the picture below.
If you are using a Mobile Collection 2.x system, a black fabric strap is included
with the EkaNet pouch. Route and buckle this strap horizontally around the
passenger seat, and then clip the pouch to it.
64
Hardware Installation Guide
Installing the EkaNet System
6. Connect the EkaNet antenna cable to the top of the radio. Note that in the following
example, the pouch and vehicle have been removed for emphasis.
7. Connect the EkaNet power cable to the AUX port on the junction box in your vehicle.
If you do not have a junction box in your installation, power will need to
be hard-wired from the vehicle's battery to the radio; see your system
administrator for assistance.
Hardware Installation Guide
65
Chapter 3
Using the EkaNet System
Note The Laptop Dock, as shown above, is only used with an MC3 radio. There
is not a connected cable attached to the laptop dock with an MC 2.x radio.
The Power Junction box, as shown above, is only used with an MC3 radio. For an
MC2.x radio, the Power Junction box needs to be ordered to supply power to the
EkaNet radio.
66
Hardware Installation Guide
Installing the EkaNet System
8. Connect the other end of the power cable to the port on the bottom of the radio. Note
that in the following example, the pouch, vehicle, and other cables have been removed
for emphasis.
9. Connect the serial cable to COM 1 serial port on the laptop (or dock); this is the end
without pins. Be sure to securely connect the cable.
For the GoBook XR-1, the serial port is located on the right-hand side of the
laptop (9-pin male connector).
For the GoBook III, the serial port is located on the back of the laptop (9-pin
male connector).
Hardware Installation Guide
67
Chapter 3
Using the EkaNet System
10. Connect the other end of the serial cable to the bottom of the EkaNet radio; this is the
end with pins. Be sure to securely connect the cable. Note that in the following
example, the pouch, vehicle, and other cables have been removed for emphasis.
When you have finished, the system should look similar to the example below.
Removing the EkaNet System
When you have finished collecting data with the EkaNet system, you can remove it from
your vehicle.
68
Hardware Installation Guide
Removing the EkaNet System
To remove the EkaNet system
1. Ensure that the vehicle is turned off.
2. Ensure that the GoBook has completed processing reads and is properly shut down.
3. Disconnect the following from the EkaNet radio inside the vehicle:
Antenna (connected to the top of the radio and pouch).
Power and serial communications cables (located on the bottom of the radio
and pouch).
4. Remove the radio and pouch from the vehicle. You can either:
Unclip the pouch from the strap it is attached to. Then unbuckle the strap and
store it with with EkaNet radio and pouch.
Hardware Installation Guide
69
Chapter 3
Using the EkaNet System
Leave the clip attached to the strap, but remove the pouch from the clip
assembly. To do so, rotate the pouch clockwise 90-degrees (1) and then pull it
straight up (2). The clip and strap can remain in the vehicle.
70
Hardware Installation Guide
CHAPTER 4
System Maintenance
This chapter introduces you to some of the basic maintenance procedures that should be
performed regularly to ensure optimal performance of your Mobile Collection system.
For more information, see:
MC3 Systems
Mobile Collection 2.x Systems
GoBook Maintenance
Antenna Maintenance
RF Antenna Maintenance
The following procedures should be followed to ensure that the RF omni-mount antenna for
your Mobile Collection system is operating properly.
Cleaning
In order to maintain both the performance and the appearance of your omni-mount RF
antenna, regular cleaning is recommended. Clean the antenna in the same manner as your
vehicle. Applying a quality car wax to the antenna and base will help protect the finish and
extend the life of the antenna.
Replacing Gaskets
To maintain the integrity and performance of the antenna, Itron recommends that you
replace the gasket located in the antenna base at least every year. Replacement gaskets (part
number MSE-0210-001, in a packet of six) are available from Itron; contact Customer
Support (1-800-635-8725) for more information.
You should also inspect the gasket regularly to verify that it is intact, free from debris, and
properly seals the antenna and base.
To replace the antenna gasket
1. Turn the antenna counter-clockwise to remove it from the base.
Hardware Installation Guide
71
Chapter 4
System Maintenance
2. Remove the gasket (1) from the base (2).
3. Place a new gasket on the base. Push it firmly into place. Ensure that it is level on the
antenna base; if it is not level, it could be pinched into the base and damaged when the
antenna is reconnected.
4. Reconnect the antenna to the base by turning it clockwise until it is firmly seated on
the base.
2.x System Maintenance
In addition to the antenna maintenance described earlier, the following tasks should be
performed regularly to keep your Mobile Collection 2.x system operating at peak
performance.
Inspecting and Replacing Filters
The Mobile Collector has two internal fans that circulate air through its components to cool
them. One fan draws air in from the side of the Mobile Collector, while the second fan
blows the air out the rear.
Each fan has a filter accessible externally that requires periodic replacement, depending on
the environment in which the Mobile Collector is operated. To replace the filter, pull the fan
cover off, replace the filter, and snap the fan cover back on.
Inspect the filters regularly and replace them when they become visibly
dirty. Contact an Itron customer service representative to order
replacement filters.
72
Hardware Installation Guide
Service Bulletins
Service Bulletins
The following information is for customers with legacy Mobile Collection systems in their
deployments.
The Service Bulletins listed below should have already been shipped to you, along with any
required hardware updates, but are included here as a reminder and to help you identify any
system components that may need updating.
Mobile Collection 2.5 / GoBook III Power Plug Issue
(Bulletin Issued June 5th, 2006)
In the interest of continuous improvement, Itron has incorporated a reliability upgrade to
your Mobile Collector. The present CBA-0259-002 cable that provides power from the RF
unit to the GoBook III has the conductor exposed on the right angle plug that is inserted into
the GoBook III. With the end of the plug exposed, it is possible to short the exposed tip on
the metal RF chassis. This only happens when power is supplied to the RF unit before this
connection is made between the RF unit and GoBook III. The result of this shorting
condition is damage to a transistor on the power board inside of the RF unit, which requires
your RF unit to be returned to Itron for repair.
To alleviate this problem, we are replacing the existing CBA-0259-002 power plug with the
enclosed CBA-0305-002. CBA-0305-002 has an insulated tip to prevent shorting on the
chassis. Please replace the existing power cable with CBA-0305-002 as soon as possible and
scrap the CBA-0259-002. We also recommend that you always connect the cable from the
RF unit to the GoBook III before you apply power to RF unit.
This improvement is also being made on all new Mobile Collection 2.5 systems being
shipped and all Mobile Collectors when they are returned for service.
If you have any questions, please contact Itron Support at 1-800-635-8725.
Hardware Installation Guide
73
Chapter 4
System Maintenance
Mobile Collector 2.x Power Adapter
(Bulletin Issued September 8th, 2006)
In the interest of continuous improvement, Itron has incorporated a reliability upgrade in
your Mobile Collector. Reliability of the existing power connector has become the number
one cause of Mobile Collector returns during the past year. As a result, we are replacing the
existing power connector with a new power connector that has tested to have improved
reliability and durability.
Along with the new power connector in your RF unit, we have included a new power cable
with new power connectors. It is imperative that you use the new power cable with your RF
unit. The old power cable will not lock into place with the new power connector.
The new power cable was designed to be easily distinguishable from the existing power
cable by placing a red and blue overmold on the connectors. A notice label was placed on
the chassis of the RF unit to remind you of this requirement.
74
Hardware Installation Guide
Service Bulletins
The operation of the new power cable is slightly different from the previous power
connector. To engage the new power connector, align the connector tab with the connector
slot on the RF unit, insert the connector and then rotate clockwise 45 degrees. To disengage
the unit, pull back the locking tab on the cable connector and then rotate the connector 45
degrees counterclockwise. Notice labels were placed on both ends of your power cable to
remind you how to disengage the new power connector.
If you presently utilize a power cable that plugs into the cigarette
lighter, you will need to contact Itron Support at 1-800-635-8725 to
request a replacement cable. You will be required to send your old
cable in as an exchange. It should be noted that Itron does not
recommend the cigarette lighter adapter configuration except for
emergency use.
This change to the new power connector will be incorporated on all new MC2.5 being
shipped and all Mobile Collectors when they are returned for service.
If you have any questions, please contact Itron Support at 1-800-635-8725.
Hardware Installation Guide
75
Chapter 4
76
System Maintenance
Hardware Installation Guide

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 80
Language                        : en-US
Tagged PDF                      : Yes
Title                           : Hardware Installation Guide
Author                          : 
Subject                         : Mobile Collection
Creator                         : Microsoft® Office Word 2007
Create Date                     : 2009:03:06 17:12:30
Modify Date                     : 2009:03:06 17:12:30
Producer                        : Microsoft® Office Word 2007

EXIF Metadata provided by EXIF.tools