Itron SPIRIT ERT(r) Repeater User Manual chapter bk

Itron, Inc. ERT(r) Repeater chapter bk

Users Manual 2

DRAFTChapter 2 - Repeater Installation 9 TDC-0613-000  10/04Sleeve-Mount RepeatersSleeve-Mount RepeatersTypes of Sleeve- Mount Sleeve-mount repeater installation depends on the type of meter socket. Required Tools The following tools are necessary for sleeve-mount repeater installation:• Tamper seals and associated meter installation/removal tools• Panduit Wave-Ty installation tool (optional). This tool cuts excess cable and applies tension to the tension band. Installing on a Ringless Meter SocketA ringless meter socket does not use a meter seal ring between the meter and the meter socket. Instead, the meter is secured in the meter socket by a lid. To install a repeater on a ringless meter socket, do the following steps.IMPORTANT The following instructions should be considered supplemental to the meter installation and removal procedures for your utility. Follow all appli-cable procedures and regulations when performing meter installation.Meter Socket Type DescriptionRingless A ringless mounted meter installs under the meter box lid, which is hinged at the top of the box.Ringed A rimmed meter box Step Action1Remove tamper seals.2Verify that the service is compatible with the repeater.3Remove the meter socket lid.4Pull the meter from the socket.5Insert the repeater into the socket.
DRAFT10 Fixed Network Repeater Installation Guide TDC-0613-000  10/04Sleeve-Mount Repeaters6Replace the meter socket lid.NOTE If needed, trim the breakaway rim on the repeater sleeve using diagonal so that the socket lid will fit over the repeater.7Place the antenna cover over the antenna on the top of the repeater sleeve.8Secure the band around the repeater, pulling to tighten. 9Tighten the tension band using a tension setting tool.10 Clip off the extra band material.11 Snap the meter into the repeater socket.12 Attach the ring making sure to catch the antenna cover lip under the ring band.13 Install a tamper seal in the ring band and on the meter socket lid.Step ActionCatch cover lip under ring
DRAFTChapter 2 - Repeater Installation 11 TDC-0613-000  10/04Sleeve-Mount RepeatersInstalling on a Ringed Meter Socket A ringed meter socket uses a meter sealing ring to secure the meter to the socket. To install a repeater on a ringed meter socket, do the following steps.Step Action1Remove tamper seals.2Verify that the service is compatible with the repeater. 3Remove the meter seal ring.4Pull the meter from the socket.5Insert the repeater sleeve into the meter socket.6Secure a meter seal ring between the repeater and the meter socket.
DRAFT12 Fixed Network Repeater Installation Guide TDC-0613-000  10/04Sleeve-Mount Repeaters7Place the antenna cover over the antenna on the top of the repeater.8Secure the antenna cover band around the repeater, pulling to tighten. 9Tighten the tension band using a tension setting tool.10 Clip off the extra band material.11 Insert the meter into the repeater socket.Step Action
DRAFTChapter 2 - Repeater Installation 13 TDC-0613-000  10/04Sleeve-Mount Repeaters12 Attach the meter seal ring making sure to catch the antenna cover lip under the ring band.13 Replace the tamper seals.Step ActionCatch cover lip under ring
DRAFT14 Fixed Network Repeater Installation Guide TDC-0613-000  10/04Sleeve-Mount Repeaters
DRAFTChapter 3 - Repeater Configuration 15 TDC-0613-000  10/04Chapter 3Repeater ConfigurationGetting StartedOverview Repeater configuration and troubleshooting is performed in the field using two components:•Repeater Programmer communicates with repeaters and endpoints. You can use the programmer in the field to troubleshoot repeater problems and optimize network performance. The programmer is connected to your computer using a serial cable and powered by a 5 volt power cord.•Itron QuickTerminal is a terminal emulation application, similar to Hyper-Terminal or ProComm.Navigating in QuickTerminal QuickTerminal displays three windows: the Data window, the Control Panel, and the Remote Unit Connection window. The Remote Unit Connection window appears following a successful connection with a repeater.Data windowControl Panel
DRAFT16 Fixed Network Repeater Installation Guide TDC-0613-000  10/04Installing QuickTerminalInstalling QuickTerminalOverview QuickTerminal may be installed directly on your machine or run directly from the CD. Note that running QuickTerminal from the CD will result in some per-formance and speed loss.Requirements The following software and hardware requirements must be met to run Quick-Terminal.Installing QuickTerminal Itron recommends installing QuickTerminal directly on your configuration machine. To install QuickTerminal, do the following steps.Requirement DescriptionMicrosoft Windows Windows XP, 2000, 98, ME, or NT Service Pack 6aMicrosoft .NET Framework Version 1.1. Available as part of Windows XP and 2000, or available from Microsoft.http://windowsupdate.microsoft.comSerial Port Available serial port capable of communi-cating at 38400 baud rateSerial Port Adapter OptionalIf your computer does not have a serial port, you may need to use a USB serial port adapter.Power Adapter OptionalA power adapter for the 5 volt power cord is required to operate the programmer in a vehicle.Step Action1Insert the QuickTerminal CD.2Navigate to the Install folder and double-click setup.exe.The QuickTerminal setup wizard launches.
DRAFTChapter 3 - Repeater Configuration 17 TDC-0613-000  10/04Installing QuickTerminalRunning QuickTerminal from CDTo run QuickTerminal directly from the CD, do this.• Insert the QuickTerminal CD.• Navigate to the Run folder and double-click QuickTerminal.exe.3Click Next to accept the default installation path or browse for an alternate path.4Click Next to confirm installation. QuickTerminal installs.5Click Close.The QuickTerminal icon will appear on your desktop and in the Start menu.Step Action
DRAFT18 Fixed Network Repeater Installation Guide TDC-0613-000  10/04Communicating with a RepeaterLaunching QuickTerminal To launch the QuickTerminal application, do this.• Double-click the QuickTerminal icon on your desktop or select Start > QuickTerminal.Communicating with a RepeaterSetting Communication OptionsYou may need to adjust the COM port or baud rate settings for communicating with the repeater. To set communication options, do the following steps.Connecting to a Remote Repeater An All Call (ACALL) command causes all of the repeaters in communication distance to move to a single frequency. You must perform a remote call prior to communicating with a repeater. To connect to a remote repeater, do the fol-lowing steps.Step Action1Connect the programmer to your computer using the serial cable.2Launch QuickTerminal.3Press F2.NOTE To view or minimize the Control Panel, press F2. To enter command mode, press ESC three times.4From Settings, select a COM port. The default is COM port 1.5Select a baud rate setting. The default baud rate is 38400.6Click Connect. • If the COM port is available, the message COM1 opened OK appears. As the programmer begins to read ERT endpoints and repeaters, data will appear.• If the COM port is available but the repeater is not connected, the port will open but no data will appear. • If the COM port is not available or not present on the machine, an error message appears.NOTE Data may not immediately display if the programmer is not able to read nearby endpoints or repeaters. If no data displays, check that the repeater is connected by removing and re-inserting the power cord into the repeaters. A status message should appear.Step Action1From the Control Panel, click Remote Call. The remote call processes and available repeaters display.2In the data window, enter the password.3Press Enter to accept the command channel frequency. NOTE If your utility has opted to use a frequency other than the standard frequency of 9100, enter your frequency.

Navigation menu