JBT Smart Lighting GNEW002999 LED STRIP User Manual GN EW002 Manual REV 080318 indd

Shenzhen JBT Smart Lighting Co.,LTD LED STRIP GN EW002 Manual REV 080318 indd

15_GN-EW002-999 UserMan, r1

SMART WI-FILED STRIPSTART GUIDEFCC statement This device complies with Part 15 of the FCC Rules: Operation is subject to the following two conditions:1. This device may not cause harmful interference and2. This device must accept any interference that is received, including any interference that may cause undesired operation.This device is acting as slave and operating in the 2.4 GHz (2412 ~2462 MHz) band.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help RF exposure warning : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body. Changes or modifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment.
ContentsDownload & Register 2-4Prepare 5-7Connect (Easy Mode) 8-9Connect (AP Mode) 10-11Questions, Troubleshooting, Notices 12-15Thank you for purchasing your GEENI smart home product.Get started using your new devices by downloading Geeni, one convenient app that manages everything straight from your phone or tablet. Easily connect to your home Wi-Fi and control multiple devices from the touch of your fingertips.
Can’t connect? Need help?DO NOT RETURN THIS PRODUCT TO THE STOREGeeni support:support@mygeeni.com(888) 232-3143 Toll-free (English Only) or tap ‘Support’ for help in the Geeni app.What’s in the BoxGet Ready• Smart Wi-Fi LED Strip• Wi-Fi Controller• Power Adapter • User Manual• Voice Control Guide• Know your Wi-Fi network and password• Make sure your mobile device is running iOS® 8 or higher or Android™ 4.1 or higher• Make sure you’re connecting to a 2.4GHz Wi-Fi network (Geeni can’t connect to 5GHz networks)SMART WI-FILED STRIPSTART GUIDEVOICECONTROLGUIDECAUTION: RISK OF ELECTRIC SHOCK OR BURNS - USE IN A DRY LOCATION ONLY. The weather resistant IP44 rating only protects the LED strip from splashes in any direction. DO NOT IMMERSE IN WATER.WARNING: The LED strip must be unplugged when making any modifications to the device. Electrical currents are dangerous and may cause electrical shock, injury, or death (in some cases)
21 Download the Geeni app from App Store or Google Play.15FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the two following conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.Important Information:Before installing, read and follow all precautions, including the following:CAUTION: RISK OF ELECTRIC SHOCK OR BURNS - USE IN A DRY LOCATION ONLY.The weather resistant IP44 rating only protects the LED strip from splashes in any direction.DO NOT IMMERSE IN WATER.WARNING: The LED strip must be unplugged when making any modifications to the device. Electrical currents are dangerous and may cause electrical shock, injury, or death (in some cases).Support:If you encounter any issues, please contact us at support@mygeeni.com for help.To explore our full selection of products, visit us at: www.mygeeni.com(888) 232-3143 Toll-free (English Only)© 2018 Merkury Innovations • 45 Broadway 3rd FL, New York NY 10006. The illustrated product and specifications may differ slightly from those supplied. Geeni is a trademark of Merkury Innovations LLC. iPhone, Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Galaxy S is a registered trademark of Samsung Electronics Co., Ltd. Google, Google Play, and related marks and logos are trademarks of Google LLC. iOS is a registered trademark of Cisco in the U.S. and other countries and is used under license. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. All other trademarks and trade names are those of their respective owners. Made in China
14TroubleshootingReset the deviceSystem RequirementsTechnical Specifi cationsCannot connect to your Wi-Fi network.Make sure you entered the correct Wi-Fi password during the Wi-Fi setup. Check whether there are any Internet connection problems.If the Wi-Fi signal is too weak, reset your Wi-Fi router and try again.Reset once (press & hold reset button) to reach Easy Mode, which is the primary way the app will try to connect. (When in Easy Mode, you’ll see the LED flashing quickly, 2x per second)Reset again (press & hold reset button) to reach AP, which is the Backup Mode to help connect.(When in AP Mode, you’ll see the LED blinking slowly, every 3 seconds)• Mobile device running iOS® 8 or higher or Android™ 4.1x or higher• Existing Wi-Fi Network• Size: 0.5in x 118in• Brightness (white): 1500 lm• Input: 100-240V, 50/60Hz• Life Span: 25000 Hours• Weatherproof: IP44 (strip), IP20 (controller)• Wi-Fi: IEEE 802.11N, 2.4GHz (not compatible with 5GHz Wi-Fi networks)32 Register an account on your Geeni app.STEP 1. Enter your mobile phone number or email address.STEP 2. Enter the verification codeand create a password.
4STEP 3. Login to the App.2 Register an account on your Geeni app.5. The device appears offline or unreachable, what should I do?Make sure your Wi-Fi router is online and in range.Make sure you have the latest Geeni functionality by clicking “Check for firmware update” in your device settings.6. What’s the Wireless Range?The range of your home Wi-Fi is heavily dependent on your home router and the conditions of the room. Check with your router specifications for exact range data.7. If my Wi-Fi/Internet goes down, will Geeni still work?Geeni products need to be connected to Wi-Fi in order to use them remotely.
12Frequently Asked Questions1. Can I share with family and friends?Yes, you can share your bulbs with family and friends who will have access to control your bulbs, plugs, cameras, and other Geeni devices. In the Geeni app, press the Profile button and click on the “Device Sharing” button, and you will be able to give or revoke sharing permissions.In order to share, the other user should already have downloaded the Geeni app and registered a new account.2. Can I group multiple Geeni devices together?Yes, you can group multiple devices of the same type together, by room, location, or however else you want. The same devices can be in multiple groups. (For example, create a group for “Bedroom” and another group for “Entire House”, and your Bedroom lights can be included in both groups). From your main device list, click on one of the devices you want to group, press the “ ” button on the top right for advanced settings, and click Create Group. You’ll then be able to choose which devices you’d like to group together and will be able to rename them.3. How Many Devices Can I Control?Geeni’s app can control an unlimited amount of devices in an unlimited amount of locations. Your router may have a limit of how many devices can be connected to one router.4. My Geeni device has a funny name. How do I rename it?From your main device list, click on one of the devices you want to rename, press the “ ” button on the top right for advanced settings, and click Modify Device Name (or Modify Group Name, if applicable). You’ll then be able to choose a more familiar name.53 PrepareHow do I reset the device and what does the blinking light mean?Reset the LED strip by pressing & holding reset button. - Reset once (press & hold reset button) to reach Easy Mode, which is the primary way the app will try to connect. (When in Easy Mode, you’ll see the LEDs flashing quickly, 2x per second)- Reset again (press & hold reset button) to reach AP Mode, which is the Backup Mode to help connect. (When in AP Mode, you’ll see the LEDs blinking slowly, every 3 seconds)+CGRBW+CGRBWPower Adapter Wi-Fi Controller LED StripReset ButtonPress: Turn On/OffPress & Hold: ResetSTEP 1. Plug the device into the wall.Make sure the indicator light on the device is flashing rapidly, indicatingthe device is ready to connect. YES+CGRBW+CGRBWWBRGC+NO+CGRBW
63 PrepareSTEP 3.Measure the LED strip for the desired length, starting at the end closest to the connectorfor the Wi-Fi Controller. IMPORTANT: If you measure & cutfrom the opposite end, you will not be able to connect the LED strip to the Wi-Fi Controller.STEP 2.Measure the area you wish to attach the LED strip to. Ensure that the area has a clean, solid surface.+CGRBW+CGRBW+CGRBW11STEP 4. Follow the instructions to choose the device from your Wi-Fi list.STEP 5. The device will connect.NOTE: Geeni can’t connect to 5GHz networks.
105 Add device. Method 2: Backup AP ModeSTEP 1. Make sure the device is in AP Mode, blinking slowly(see reset instructions on p. 5)STEP 2. In the Geeni app, on the top corner of the Devices screen, click (+).Choose “AP Mode” in the top corner.Choose “Smart Lighting”STEP 3. Click Next and enter your Wi-Fi details.7STEP 4. Located the closest cut mark to your desired length. Each strip has cut markings located every 10cm. Take a sharp pair of scissors or blade, and cut along the cut mark. STEP 5. Remove the protective film from the adhesive backing to mount the LED strip to the desired area.+CGRBW+CGRBW+CGRBW+CGRBW+CGRBW+CGRBW
8STEP 1. In the Geeni app, on the top corner of the Devices screen, click (+).Choose “Smart Lighting”STEP 2. Make sure the indicator light is flashing quickly, indicating it’s ready to connect. If not, turn the bulb off and on 3 times until it is flashing. Press “Next Step.” 4 Add device. Method 1: Easy Mode9STEP 3. Enter your Wi-Fi network and password.NOTE: Geeni can’t connect to 5GHz networks.*If the connection fails, try to connect using AP Mode.STEP 4. The Geeni app will try to connect your device.

Navigation menu