JBT Smart Lighting GNEW002999 LED STRIP User Manual GN EW002 Manual REV 080318 indd

Download:
Mirror Download [FCC.gov]
Document ID	4048351
Application ID	LQ11OWmzNzYw9Xf55U4fBw==
Document Description	15_GN-EW002-999 UserMan, r1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	78.47kB (980855 bits)
Date Submitted	2018-10-25 00:00:00
Date Available	2018-10-25 00:00:00
Creation Date	2018-08-03 10:34:55
Producing Software	Acrobat Distiller 18.0 (Macintosh)
Document Lastmod	2018-10-22 14:12:17
Document Title	GN-EW002_Manual_REV_080318.indd
Document Creator	Adobe InDesign CC 13.1 (Macintosh)
Document Author:	Dmitrys

FCC
statement
This device complies with Part 15 of the FCC Rules: Operation is subject to
the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference that is received, including any interfer
ence that may cause undesired operation.
RF exposure warning :
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and operated with minimum distance 20cm
between the radiator & body.
This device is acting as slave and operating in the 2.4 GHz (2412 ~2462 MHz)
band.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
SMART WI-FI
LED STRIP
START GUIDE
Thank you for purchasing your GEENI smart home product.
Get started using your new devices by downloading Geeni, one
convenient app that manages everything straight from your
phone or tablet. Easily connect to your home Wi-Fi and control
multiple devices from the touch of your fingertips.
Contents
Download & Register
2-4
Prepare
5-7
Connect (Easy Mode)
8-9
Connect (AP Mode)
10-11
Questions, Troubleshooting, Notices
12-15
Can’t connect? Need help?
CAUTION: RISK OF ELECTRIC SHOCK OR BURNS - USE IN A DRY LOCATION ONLY. The
weather resistant IP44 rating only protects the LED strip from splashes in any direction.
DO NOT IMMERSE IN WATER.
WARNING: The LED strip must be unplugged when making any modifications to the
device. Electrical currents are dangerous and may cause electrical shock, injury, or death
(in some cases)
What’s in the Box
SMART WI-FI
LED STRIP
START GUIDE
VOICE
CONTROL
GUIDE
• Smart Wi-Fi LED Strip
• Wi-Fi Controller
• Power Adapter
• User Manual
• Voice Control Guide
DO NOT RETURN THIS
PRODUCT TO THE STORE
Geeni support:
support@mygeeni.com
(888) 232-3143 Toll-free (English Only)
or tap ‘Support’ for help in the Geeni app.
Get Ready
• Know your Wi-Fi network and password
• Make sure your mobile device is running iOS® 8 or higher
or Android™ 4.1 or higher
• Make sure you’re connecting to a 2.4GHz Wi-Fi network
(Geeni can’t connect to 5GHz networks)
1
FCC Notice:
Download the Geeni app from App Store or Google Play.
This device complies with Part 15 of the FCC Rules. Operation is subject to the two following
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
Important Information:
Before installing, read and follow all precautions, including the following:
CAUTION: RISK OF ELECTRIC SHOCK OR BURNS - USE IN A DRY LOCATION ONLY.
The weather resistant IP44 rating only protects the LED strip from splashes in any direction.
DO NOT IMMERSE IN WATER.
WARNING: The LED strip must be unplugged when making any modifications to the device.
Electrical currents are dangerous and may cause electrical shock, injury, or death (in some
cases).
Support:
If you encounter any issues, please contact us at support@mygeeni.com for help.
To explore our full selection of products, visit us at: www.mygeeni.com
(888) 232-3143 Toll-free (English Only)
© 2018 Merkury Innovations • 45 Broadway 3rd FL, New York NY 10006.
The illustrated product and specifications may differ slightly from those supplied. Geeni is a trademark of Merkury
Innovations LLC. iPhone, Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other
countries. App Store is a service mark of Apple Inc. Galaxy S is a registered trademark of Samsung Electronics
Co., Ltd. Google, Google Play, and related marks and logos are trademarks of Google LLC. iOS is a registered
trademark of Cisco in the U.S. and other countries and is used under license. Amazon, Alexa and all related logos
are trademarks of Amazon.com, Inc. or its affiliates. All other trademarks and trade names are those of their
respective owners.
Made in China
15
Troubleshooting
Cannot connect to your Wi-Fi network.
Make sure you entered the correct Wi-Fi password during the Wi-Fi
setup. Check whether there are any Internet connection problems.
If the Wi-Fi signal is too weak, reset your Wi-Fi router and try again.
Register an account on your Geeni app.
Reset the device
Reset once (press & hold reset button) to reach Easy Mode, which is the
primary way the app will try to connect. (When in Easy Mode, you’ll see
the LED flashing quickly, 2x per second)
Reset again (press & hold reset button) to reach AP, which is the Backup
Mode to help connect.
(When in AP Mode, you’ll see the LED blinking slowly, every 3 seconds)
System Requirements
• Mobile device running iOS® 8 or higher or Android™ 4.1x or higher
• Existing Wi-Fi Network
Technical Specifications
• Size: 0.5in x 118in
• Brightness (white): 1500 lm
• Input: 100-240V, 50/60Hz
• Life Span: 25000 Hours
14
STEP 1.
STEP 2.
Enter your mobile phone number
or email address.
Enter the verification code
and create a password.
• Weatherproof:
IP44 (strip), IP20 (controller)
• Wi-Fi: IEEE 802.11N, 2.4GHz (not
compatible with 5GHz Wi-Fi networks)
2
Register an account on your Geeni app.
5. The device appears offline or unreachable, what should I do?
Make sure your Wi-Fi router is online and in range.
Make sure you have the latest Geeni functionality by clicking “Check for
firmware update” in your device settings.
6. What’s the Wireless Range?
STEP 3.
The range of your home Wi-Fi is heavily dependent on your home router
and the conditions of the room. Check with your router specifications for
exact range data.
Login to the App.
7. If my Wi-Fi/Internet goes down, will Geeni still work?
Geeni products need to be connected to Wi-Fi in order to use them remotely.
Frequently Asked Questions
1. Can I share with family and friends?
Prepare
Yes, you can share your bulbs with family and friends who will have
access to control your bulbs, plugs, cameras, and other Geeni devices. In
the Geeni app, press the Profile button and click on the “Device Sharing”
button, and you will be able to give or revoke sharing permissions.
In order to share, the other user should already have downloaded the
Geeni app and registered a new account.
Reset Button
Press: Turn On/Off
Press & Hold: Reset
2. Can I group multiple Geeni devices together?
Yes, you can group multiple devices of the same type together, by room,
location, or however else you want. The same devices can be in multiple
groups. (For example, create a group for “Bedroom” and another group
for “Entire House”, and your Bedroom lights can be included in both
groups). From your main device list, click on one of the devices you want
to group, press the “ ” button on the top right for advanced settings,
and click Create Group. You’ll then be able to choose which devices you’d
like to group together and will be able to rename them.
3. How Many Devices Can I Control?
Geeni’s app can control an unlimited amount of devices in an unlimited
amount of locations. Your router may have a limit of how many devices
can be connected to one router.
4. My Geeni device has a funny name. How do I rename it?
From your main device list, click on one of the devices you want to rename,
press the “ ” button on the top right for advanced settings, and click
Modify Device Name (or Modify Group Name, if applicable). You’ll then be
able to choose a more familiar name.
12
Power Adapter
Wi-Fi Controller
LED Strip
STEP 1.
Plug the device into the wall.
Make sure the indicator light on the
device is flashing rapidly, indicating
the device is ready to connect.
YES
NO
How do I reset the device and what does the blinking light mean?
Reset the LED strip by pressing & holding reset button.
- Reset once (press & hold reset button) to reach Easy Mode,
which is the primary way the app will try to connect.
(When in Easy Mode, you’ll see the LEDs flashing quickly, 2x per second)
- Reset again (press & hold reset button) to reach AP Mode,
which is the Backup Mode to help connect.
(When in AP Mode, you’ll see the LEDs blinking slowly, every 3 seconds)
3
Prepare
STEP 2.
Measure the area you wish to attach the LED strip
to. Ensure that the area has a clean, solid surface.
STEP 3.
Measure the LED strip for the desired length,
starting at the end closest to the connector
for the Wi-Fi Controller.
IMPORTANT: If you measure & cut
from the opposite end, you will not be able to
connect the LED strip to the Wi-Fi Controller.
STEP 4.
STEP 5.
Follow the instructions to choose
the device from your Wi-Fi list.
The device will connect.
NOTE: Geeni can’t connect to 5GHz networks.
11
5
Add device. Method 2: Backup AP Mode
STEP 1.
Make sure the device is in AP Mode, blinking slowly
(see reset instructions on p. 5)
STEP 4.
Located the closest cut mark to
your desired length. Each strip has
cut markings located every 10cm.
Take a sharp pair of scissors or
blade, and cut along the cut mark.
10
STEP 2.
STEP 3.
In the Geeni app, on the top corner
of the Devices screen, click (+).
Choose “AP Mode” in the top corner.
Choose “Smart Lighting”
Click Next and enter your
Wi-Fi details.
STEP 5.
Remove the protective film from
the adhesive backing to mount the
LED strip to the desired area.
4
Add device. Method 1: Easy Mode
STEP 1.
STEP 2.
STEP 3.
STEP 4.
In the Geeni app, on the top
corner of the Devices screen,
click (+).
Choose “Smart Lighting”
Make sure the indicator light is
flashing quickly, indicating it’s ready
to connect. If not, turn the bulb off
and on 3 times until it is flashing.
Press “Next Step.”
Enter your Wi-Fi network and
password.
The Geeni app will try to
connect your device.
NOTE: Geeni can’t connect to 5GHz networks.
*If the connection fails, try to connect using AP Mode.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : Adobe InDesign CC 13.1 (Macintosh)
Create Date                     : 2018:08:03 10:34:55-04:00
Modify Date                     : 2018:10:22 14:12:17+08:00
Metadata Date                   : 2018:10:22 14:12:17+08:00
Format                          : application/pdf
Creator                         : Dmitrys
Title                           : GN-EW002_Manual_REV_080318.indd
Producer                        : Acrobat Distiller 18.0 (Macintosh)
Document ID                     : uuid:5a03a7e2-0178-ec4b-bd48-27e9dc85d0c5
Instance ID                     : uuid:405ff4f4-262c-4bfa-929a-b47031bc0db4
Has XFA                         : No
Page Count                      : 10
Author                          : Dmitrys

EXIF Metadata provided by EXIF.tools