JBT Smart Lighting GNEW002999 LED STRIP User Manual GN EW002 Manual REV 080318 indd
Shenzhen JBT Smart Lighting Co.,LTD LED STRIP GN EW002 Manual REV 080318 indd
15_GN-EW002-999 UserMan, r1
SMART WI-FI
LED STRIP
START GUIDE
FCC statement
This device complies with Part 15 of the FCC Rules: Operation is subject to
the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference that is received, including any interfer
ence that may cause undesired operation.
This device is acting as slave and operating in the 2.4 GHz (2412 ~2462 MHz)
band.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
RF exposure warning :
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and operated with minimum distance 20cm
between the radiator & body.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Contents
Download & Register 2-4
Prepare 5-7
Connect (Easy Mode) 8-9
Connect (AP Mode) 10-11
Questions, Troubleshooting, Notices 12-15
Thank you for purchasing your GEENI smart home product.
Get started using your new devices by downloading Geeni, one
convenient app that manages everything straight from your
phone or tablet. Easily connect to your home Wi-Fi and control
multiple devices from the touch of your fingertips.
Can’t connect? Need help?
DO NOT RETURN THIS
PRODUCT TO THE STORE
Geeni support:
support@mygeeni.com
(888) 232-3143 Toll-free (English Only)
or tap ‘Support’ for help in the Geeni app.
What’s in the Box
Get Ready
• Smart Wi-Fi LED Strip
• Wi-Fi Controller
• Power Adapter
• User Manual
• Voice Control Guide
• Know your Wi-Fi network and password
• Make sure your mobile device is running iOS® 8 or higher
or Android™ 4.1 or higher
• Make sure you’re connecting to a 2.4GHz Wi-Fi network
(Geeni can’t connect to 5GHz networks)
SMART WI-FI
LED STRIP
START GUIDE
VOICE
CONTROL
GUIDE
CAUTION: RISK OF ELECTRIC SHOCK OR BURNS - USE IN A DRY LOCATION ONLY. The
weather resistant IP44 rating only protects the LED strip from splashes in any direction.
DO NOT IMMERSE IN WATER.
WARNING: The LED strip must be unplugged when making any modifications to the
device. Electrical currents are dangerous and may cause electrical shock, injury, or death
(in some cases)
2
1 Download the Geeni app from App Store or Google Play.
15
FCC Notice:
This device complies with Part 15 of the FCC Rules. Operation is subject to the two following
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
Important Information:
Before installing, read and follow all precautions, including the following:
CAUTION: RISK OF ELECTRIC SHOCK OR BURNS - USE IN A DRY LOCATION ONLY.
The weather resistant IP44 rating only protects the LED strip from splashes in any direction.
DO NOT IMMERSE IN WATER.
WARNING: The LED strip must be unplugged when making any modifications to the device.
Electrical currents are dangerous and may cause electrical shock, injury, or death (in some
cases).
Support:
If you encounter any issues, please contact us at support@mygeeni.com for help.
To explore our full selection of products, visit us at: www.mygeeni.com
(888) 232-3143 Toll-free (English Only)
© 2018 Merkury Innovations • 45 Broadway 3rd FL, New York NY 10006.
The illustrated product and specifications may differ slightly from those supplied. Geeni is a trademark of Merkury
Innovations LLC. iPhone, Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other
countries. App Store is a service mark of Apple Inc. Galaxy S is a registered trademark of Samsung Electronics
Co., Ltd. Google, Google Play, and related marks and logos are trademarks of Google LLC. iOS is a registered
trademark of Cisco in the U.S. and other countries and is used under license. Amazon, Alexa and all related logos
are trademarks of Amazon.com, Inc. or its affiliates. All other trademarks and trade names are those of their
respective owners.
Made in China
14
Troubleshooting
Reset the device
System Requirements
Technical Specifi cations
Cannot connect to your Wi-Fi network.
Make sure you entered the correct Wi-Fi password during the Wi-Fi
setup. Check whether there are any Internet connection problems.
If the Wi-Fi signal is too weak, reset your Wi-Fi router and try again.
Reset once (press & hold reset button) to reach Easy Mode, which is the
primary way the app will try to connect. (When in Easy Mode, you’ll see
the LED flashing quickly, 2x per second)
Reset again (press & hold reset button) to reach AP, which is the Backup
Mode to help connect.
(When in AP Mode, you’ll see the LED blinking slowly, every 3 seconds)
• Mobile device running iOS® 8 or higher or Android™ 4.1x or higher
• Existing Wi-Fi Network
• Size: 0.5in x 118in
• Brightness (white): 1500 lm
• Input: 100-240V, 50/60Hz
• Life Span: 25000 Hours
• Weatherproof:
IP44 (strip), IP20 (controller)
• Wi-Fi: IEEE 802.11N, 2.4GHz (not
compatible with 5GHz Wi-Fi networks)
3
2 Register an account on your Geeni app.
STEP 1.
Enter your mobile phone number
or email address.
STEP 2.
Enter the verification code
and create a password.
4
STEP 3.
Login to the App.
2 Register an account on your Geeni app.
5. The device appears offline or unreachable, what should I do?
Make sure your Wi-Fi router is online and in range.
Make sure you have the latest Geeni functionality by clicking “Check for
firmware update” in your device settings.
6. What’s the Wireless Range?
The range of your home Wi-Fi is heavily dependent on your home router
and the conditions of the room. Check with your router specifications for
exact range data.
7. If my Wi-Fi/Internet goes down, will Geeni still work?
Geeni products need to be connected to Wi-Fi in order to use them remotely.
12
Frequently Asked Questions
1. Can I share with family and friends?
Yes, you can share your bulbs with family and friends who will have
access to control your bulbs, plugs, cameras, and other Geeni devices. In
the Geeni app, press the Profile button and click on the “Device Sharing”
button, and you will be able to give or revoke sharing permissions.
In order to share, the other user should already have downloaded the
Geeni app and registered a new account.
2. Can I group multiple Geeni devices together?
Yes, you can group multiple devices of the same type together, by room,
location, or however else you want. The same devices can be in multiple
groups. (For example, create a group for “Bedroom” and another group
for “Entire House”, and your Bedroom lights can be included in both
groups). From your main device list, click on one of the devices you want
to group, press the “ ” button on the top right for advanced settings,
and click Create Group. You’ll then be able to choose which devices you’d
like to group together and will be able to rename them.
3. How Many Devices Can I Control?
Geeni’s app can control an unlimited amount of devices in an unlimited
amount of locations. Your router may have a limit of how many devices
can be connected to one router.
4. My Geeni device has a funny name. How do I rename it?
From your main device list, click on one of the devices you want to rename,
press the “ ” button on the top right for advanced settings, and click
Modify Device Name (or Modify Group Name, if applicable). You’ll then be
able to choose a more familiar name.
5
3 Prepare
How do I reset the device and what does the blinking light mean?
Reset the LED strip by pressing & holding reset button.
- Reset once (press & hold reset button) to reach Easy Mode,
which is the primary way the app will try to connect.
(When in Easy Mode, you’ll see the LEDs flashing quickly, 2x per second)
- Reset again (press & hold reset button) to reach AP Mode,
which is the Backup Mode to help connect.
(When in AP Mode, you’ll see the LEDs blinking slowly, every 3 seconds)
+
C
G
R
B
W
+
C
G
R
B
W
Power Adapter Wi-Fi Controller LED Strip
Reset Button
Press: Turn On/Off
Press & Hold: Reset
STEP 1.
Plug the device into the wall.
Make sure the indicator light on the
device is flashing rapidly, indicating
the device is ready to connect. YES
+
C
G
R
B
W
+
C
G
R
B
W
W
B
R
G
C
+
NO
+
C
G
R
B
W
6
3 Prepare
STEP 3.
Measure the LED strip for the desired length,
starting at the end closest to the connector
for the Wi-Fi Controller.
IMPORTANT: If you measure & cut
from the opposite end, you will not be able to
connect the LED strip to the Wi-Fi Controller.
STEP 2.
Measure the area you wish to attach the LED strip
to. Ensure that the area has a clean, solid surface.
+
C
G
R
B
W
+
C
G
R
B
W
+
C
G
R
B
W
11
STEP 4.
Follow the instructions to choose
the device from your Wi-Fi list.
STEP 5.
The device will connect.
NOTE: Geeni can’t connect to 5GHz networks.
10
5 Add device. Method 2: Backup AP Mode
STEP 1.
Make sure the device is in AP Mode, blinking slowly
(see reset instructions on p. 5)
STEP 2.
In the Geeni app, on the top corner
of the Devices screen, click (+).
Choose “AP Mode” in the top corner.
Choose “Smart Lighting”
STEP 3.
Click Next and enter your
Wi-Fi details.
7
STEP 4.
Located the closest cut mark to
your desired length. Each strip has
cut markings located every 10cm.
Take a sharp pair of scissors or
blade, and cut along the cut mark.
STEP 5.
Remove the protective film from
the adhesive backing to mount the
LED strip to the desired area.
+
C
G
R
B
W
+
C
G
R
B
W
+
C
G
R
B
W
+
C
G
R
B
W
+
C
G
R
B
W
+
C
G
R
B
W
8
STEP 1.
In the Geeni app, on the top
corner of the Devices screen,
click (+).
Choose “Smart Lighting”
STEP 2.
Make sure the indicator light is
flashing quickly, indicating it’s ready
to connect. If not, turn the bulb off
and on 3 times until it is flashing.
Press “Next Step.”
4 Add device. Method 1: Easy Mode
9
STEP 3.
Enter your Wi-Fi network and
password.
NOTE: Geeni can’t connect to 5GHz networks.
*If the connection fails, try to connect using AP Mode.
STEP 4.
The Geeni app will try to
connect your device.