JBT Smart Lighting SPKDL6RGBTWWH LED down light User Manual 15 PK DL6 RGBTW WH UserMan r1

Shenzhen JBT Smart Lighting Co.,LTD LED down light 15 PK DL6 RGBTW WH UserMan r1

15_PK-DL6-RGBTW-WH UserMan, r1

Download: JBT Smart Lighting SPKDL6RGBTWWH LED down light User Manual 15 PK DL6 RGBTW WH UserMan  r1
Mirror Download [FCC.gov]JBT Smart Lighting SPKDL6RGBTWWH LED down light User Manual 15 PK DL6 RGBTW WH UserMan  r1
Document ID4035494
Application IDPfz19EyplSseTOKzJbhYxA==
Document Description15_PK-DL6-RGBTW-WH UserMan, r1
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize20.97kB (262147 bits)
Date Submitted2018-10-15 00:00:00
Date Available2018-10-15 00:00:00
Creation Date2018-10-11 14:45:49
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2018-10-15 10:05:55
Document Title15_PK-DL6-RGBTW-WH UserMan, r1
Document CreatorMicrosoft® Office Word 2007
Document Author: 李广印

Installation Instructions
This retrofit kit includes an LED lamp and Installation instructions. Please check these items when unpackaging.
The units covered in this report are intended to retrofit Type IC or Non-IC covered ceiling recessed luminaire with through-branch wiring
marked “Max. 8 of 12 AWG conductors” with instructions to remove the existing trim and diffuser.
WARNING
Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of
luminaires electrical systems. If not qualified, do not attempt installation. Contact
a qualified electrician.
WARNING
Risk of fire or electric shock. Install this kit only in luminaires that have the construction
features and dimensions shown in the photographs and/or drawings and where the input
rating of the retrofit kit does not exceed the input rating of the luminaire.
WARNING
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or
other sharp objects.Do not make or alter any open holes in an enclosure of wiring or
electrical components during kit installation.
Electrical parameters:
Model No.
Input
voltage,
Vac
Input
Current ,Ma
Input
wattage ,W
SPK-DL6-RGBTW-WH
100-130V
210
13W
Product size:
Unit: inches
INSTALLATIONS:
STEP1:
Turn off the power before installation, Remove the diffuser or existing bulb, if necessary and remove the existing trim. Attach
the relamping label to the inside of recessed luminaire housing.
STEP2:
As shown in Figure 1
Twist the lamp base into the lamp holder.
STEP3:
As shown in Figure 2
Connected the lamp connector with lamp
base connector.
STEP4:
As shown in Figure 4
Push the LED retrofit trim into the recessed
light fixture, allowing the torsion springs to pull the LED trim up into the recessed light fixture. Continue to push the LED trim
until its outer edge is flush against the ceiling
FCC statement
This device complies with Part 15 of the FCC Rules: Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference that is received, including any interfere ence that may cause undesired operation.
*RF warning for Portable device: The device has been evaluated to meet general
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Language                        : zh-CN
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : 李广印
Create Date                     : 2018:10:11 14:45:49+08:00
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2018:10:15 10:05:55+08:00
Metadata Date                   : 2018:10:15 10:05:55+08:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:0922f8eb-3999-4f97-978e-d62ac381a9b0
Instance ID                     : uuid:399886e6-4900-41d9-b4ea-500aa2b0e7d1
Page Count                      : 2
Author                          : 李广印
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2AKG3SPKDL6RGBTWWH

Navigation menu