JVC KD DV5605UH Install_KD DV5606_004A_f User Manual DV5605UH, DV5606UH GET0654 004A
KD-DV5604UI KD-DV5604UI GET0654-004A English, INSTALLATION MANUAL
KD-DV5606U KD-DV5606U, KD-DV5606UH GET0654-004A English, INSTALLATION MANUAL
KD-DV5605U KD-DV5605U, KD-DV5605UH GET0654-004A English, INSTALLATION MANUAL
User Manual: JVC KD-DV5605UH KD-DV5605UH, KD-DV5606UH English, INSTALLATION MANUAL
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
KD-DV5606/KD-DV5605/ KD-DV5604 Installation/Connection Manual GET0654-004A 0110DTSMDTJEIN [U/UH/UI] EN © 2010 Victor Company of Japan, Limited INSTALLATION (IN-DASH MOUNTING) This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers. The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits. • If you are not sure how to install this unit correctly, have it installed by a qualified technician. WARNINGS • DO NOT install any unit or wire any cable in a location where; – it may obstruct the steering wheel and gearshift lever operations. – it may obstruct the operation of safety devices such as air bags. – it may obstruct visibility. • DO NOT operate the unit while driving. • If you need to operate the unit while driving, be sure to look around carefully. • The driver must not watch the monitor while driving. If the parking brake is not engaged, “DRIVER MUST NOT WATCH THE MONITOR WHILE DRIVING.” appears on the monitor, and no playback picture will be shown. – This warning appears only when the parking brake lead is connected to the parking brake system built in the car. * PRECAUTIONS on power supply and speaker connections: • DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged. • BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car. Do the required electrical connections. To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit. • Be sure to ground this unit to the car’s chassis again after installation. Bend the appropriate tabs to hold the sleeve firmly in place. Notes: • Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer. • It is recommended to connect speakers with a maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, changesetting to prevent the speakers from being damaged (see page 27 of the INSTRUCTIONS). • To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape. • The heat sink becomes very hot after use. Be careful not to touch it when removing this unit. * When you stand the unit, be careful not to damage the fuse on the rear. When using the optional stay Stay (option) Heat sink Fire wall When installing the unit without using the sleeve In a Toyota car for example, first remove the car radio and install the unit in its place. Flat head screws—M5 × 8 mm (not supplied) Parts list for installation and connection If any item is missing, consult your JVC car audio dealer immediately. Dashboard Screw (option) Pocket Bracket (not supplied) C Sleeve A / B Hard case/Control panel D Trim plate Install the unit at an angle of less than 30˚. Removing the unit Before removing the unit, release the rear section. E Power cord H Lock nut (M5) F Handles G Washer (ø5) I Mounting bolt (M5 × 20 mm) J Rubber cushion TROUBLESHOOTING • The fuse blows. * Are the red and black leads connected correctly? • Noise interfere with sounds. * Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords? • Power cannot be turned on. * Is the yellow lead connected? • This unit becomes hot. * Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers grounded in common? • No sound from the speakers. * Is the speaker output lead short-circuited? • This unit does not work at all. * Have you reset your unit? • Sound is distorted. * Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers grounded in common? 1 Install_KD-DV5606_004A_f.indd 1 1/29/10 9:33:38 AM ELECTRICAL CONNECTIONS A Typical connections IMPORTANT: A custom wiring harness (separately purchased) which is suitable for your car is recommended for connection between the unit and your car. • Consult your JVC car audio dealer or a company supplying kits for details. VIDEO OUT (see diagram ) Reset the unit. 15 A fuse Rear ground terminal Antenna terminal LINE OUT (REAR) (see diagram ) Ignition switch Black To metallic body or chassis of the car Yellow *2 Red To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V) Fuse block To an accessory terminal in the fuse block Blue To the automatic antenna if any (250 mA max.) Blue (white stripe) To the remote lead of other equipment (200 mA max.) Orange (white stripe) To car light control switch Light green (see “Connecting the parking brake wire” ) White (black stripe) White Gray (black stripe) Front speaker (left) B Gray Green (black stripe) Front speaker (right) Green Purple (black stripe) Rear speaker (left) Purple Rear speaker (right) Connecting the parking brake wire Required connections for video playback (A) When installing the monitor in a location where it CAN be seen by the driver Connect the parking brake wire to the parking brake system built in the car. Video cord *1 Parking brake wire (light green) KV-MR9010 Crimp connector *1 9-INCH WIDESCREEN MONITOR *1 Parking brake C To metallic body or chassis of the car Connecting the external amplifier Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused. Remote lead Parking brake switch (inside the car) Y-connector *1 (B) When installing the monitor in a location where it CANNOT be seen by the driver Remote lead (blue, white stripe) Connect the parking brake wire to metallic body or chassis of the car. To the remote lead of other equipment or automatic antenna if any *1 Rear speakers *1 JVC Amplifier Parking brake wire (light green) Signal cord *1 Front speakers *1 Not supplied for this unit. *2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on. *3 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint. 2 Install_KD-DV5606_004A_f.indd 2 1/29/10 9:33:40 AM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Create Date : 2010:01:29 09:33:48+08:00 Modify Date : 2010:02:02 08:27:29+08:00 Producer : Acrobat Distiller 9.0.0 (Macintosh) Creation Date : 2010:01:29 09:33:48+08:00 Mod Date : 2010:02:02 08:27:29+08:00 Author : 0901c Creator Tool : Adobe InDesign CS3 (5.0) Metadata Date : 2010:02:02 08:27:29+08:00 Document ID : uuid:7517558a-f0f2-0546-bf80-8f56637bc38a Instance ID : uuid:5d7fdbaa-2683-7f43-98cb-c9e5d3e2f75f Format : application/pdf Title : Install_KD-DV5606_004A_f.indd Creator : 0901c Page Count : 2EXIF Metadata provided by EXIF.tools