Janam Technologies XM20 MOBILE BARCODE TERMINAL User Manual PowerPoint Presentation

Janam Technologies LLC MOBILE BARCODE TERMINAL PowerPoint Presentation

Users Manual

Quick Start GuideLPT20 Series mobile computer
Features front and side views1234567891011121314151. Power button2. Keypad3. LCD display4. Charging LED5. Status LED6. USB connector7. Lanyard hole8. Stylus9. Scan / action button10. Action button11. Battery cover12. Scan / action button13. Up button14. Down button
Features rear, top and bottom views1. Data capture window2. Stylus3. Speaker4. Label recess5. Battery cover latch6. Battery cover7. Handstrap clip 8. USB Connector9. Handstrap bar10. Reset Key11. Battery cover switch6543217891011
Getting started installing card and batteryInstalling MicroSD card1. Remove battery if necessary2. Insert MicroSD card into the card slot3. Make sure the card connector (the golden contacts) should be at the front of insert34Installing battery–If battery cover is installed on the device, slide the battery latch to the left.–The battery cover will lift up slightly, grasp the battery cover and remove it–Insert the battery, left side (with golden contacts) first, into the battery compartment–Press the battery down until the battery fully rests on the bottom of battery compartment–Put the battery cover back, tab first, and press down until the latch secure the battery cover
Removing battery1. Slide the battery latch to the left.2. The battery cover will lift up slightly, grasp the battery cover and remove it3. Remove the battery, right side first, from the battery compartmenGetting started installing card and battery3
Installing handstrap1. Separate the velcro of the handstrap.2. Feed the loose end of the extended handstrap through the handstrap clip3. Wrap the handstrap around the clip and fasten together to close the strapCalibrating screen1. For turn on the device 1st time 2. Follow the instructions on the welcome utility screen3. Tap 5 crosses as appeared on the screen to calibrate the touch screenGetting started
Enabling WiFi1. Tap Start Menu, then tap and hold the Settings2. Select Network Connections3. Tap and hold AR6K_SD1 icon, make sure it is Enable4. Double click the Network icon on the status bar, pick the desired AP and setup as the wireless AP properties as usualDisabling WiFi1. Tap Start Menu, then tap and hold the Settings2. Select Network Connections3. Tap and hold AR6K_SD1 icon, make sure it is DisableGetting started Enabling & disabling WiFi
Enabling Bluetooth1. Tap Start Menu, then tap and hold the Settings2. Select Control Panel3. Double click Bluetooth Device Properties icon4. Pick the Tools menu and then select Turn on Bluetooth item5. Select Search Device and carry out bluetooth device operations as usualDisabling Bluetooth1. Tap Start Menu, then tap and hold the Settings2. Select Control Panel3. Double click Bluetooth Device Properties icon4. Pick the Tools menu and then select Turn off Bluetooth itemGetting started Enabling & disabling BT
Performing soft reset1. Slide the battery latch to the left and grasp the battery cover and remove it2. Use a stylus to press the reset key and release3. The device is resetPerforming hard reset1. Slide the battery latch to the left and grasp the battery cover and remove it2. Press “2” (or “8” if you want to format the NAND flash as well) on the numeric keypad3. Keep pressing the key, use a stylus to press the reset key and release4. When the green LED is flashing, release key “2” or “8”5. Put back the battery cover and calibrate the screenGetting started Soft and hard resetReset key
Getting started Refreshing ROMRefreshing LPT20 ROM1. Copy NK.bin, EBOOT.nb0 and splash.bin (optional) to the root directory of the microSD card2. Open the battery cover, remove the battery 3. Insert the microSD card4. Press and hold the left and right side Scan / Action button5. Install the battery to the battery compartment6. Continue to press and hold the left and right side Scan / Action button until the Update Screen appears7. Once NK.bin, EBOOT.nb0 and splash.bin (optional ) have 100% complete updated. Remove the battery and microSD card from the device.8. Insert the battery to the battery compartment again9. Performing the hard reset with NFLASH format4 478
65oGetting started Capturing data65o
Battery safety guidelines1. Use manufacturer’s original battery and charger only. Any incompatible battery or charger may result in in a fire, explosion, or other hazard.2. Do not disassemble or open, crush, bend or deform, puncture, or shred the battery3. Do not short circuit a battery by allowing conductive materials to contact the battery terminals.4. Charge the mobile device, the battery and charger temperatures must be between 0 ºC and +40 ºC5. Do not immerse or expose the battery to water or other liquids.6. Do not dispose of batteries in fire or place the battery into a microwave oven or dryer.7. If battery leakage is found, avoid the liquid to come in contact with the skin or eyes. If contact has been made, rinse the affected area with water and seek medical advice.8. If you suspect damage to your equipment or battery, contact the manufacturer for inspection.9. Follow the local regulations to dispose or recycle the used re-chargeable batteries.Getting started Battery warning
CE Marking and European Economic Area (EEA)Hereby, Portable Innovation Technology Ltd. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive, 1999/5/EC.Radio Frequency Interference Requirements-FCCNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected• Consult the dealer or an experienced radio/TV technician for help.Statement of Compliance
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The Equipment should be operated with minimum distance 1cm between the radiator and user body.Warning

Navigation menu