Janam Technologies XM20 MOBILE BARCODE TERMINAL User Manual PowerPoint Presentation

Download:
Mirror Download [FCC.gov]
Document ID	2060282
Application ID	G9p6L9DmgqRkzZXOscj8fA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	43.58kB (544745 bits)
Date Submitted	2013-09-03 00:00:00
Date Available	2013-09-03 00:00:00
Creation Date	2013-09-02 19:59:13
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2013-09-02 20:00:20
Document Title	PowerPoint Presentation
Document Creator	Acrobat PDFMaker 11 PowerPoint 版
Document Author:	Joey Lau

LPT20 Series mobile computer
Quick Start Guide
Features
front and side views
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Power button
Keypad
LCD display
Charging LED
Status LED
USB connector
Lanyard hole
Stylus
Scan / action
button
Action button
Battery cover
Scan / action
button
Up button
Down button
12
13
10
14
15
11
Features
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
rear, top and bottom views
Data capture
window
Stylus
Speaker
Label recess
Battery cover latch
Battery cover
Handstrap clip
USB Connector
Handstrap bar
Reset Key
Battery cover
switch
11
10
Getting started
installing card and battery
Installing MicroSD card
1.
2.
3.
Remove battery if necessary
Insert MicroSD card into the card slot
Make sure the card connector (the golden contacts) should be at the front of
insert
Installing battery
–
–
–
–
–
If battery cover is installed on the device,
slide the battery latch to the left.
The battery cover will lift up slightly, grasp
the battery cover and remove it
Insert the battery, left side (with golden
contacts) first, into the battery compartment
Press the battery down until the battery
fully rests on the bottom of battery
compartment
Put the battery cover back, tab first, and
press down until the latch secure the
battery cover
Getting started
installing card and battery
Removing battery
1.
2.
3.
Slide the battery latch to the left.
The battery cover will lift up
slightly, grasp the battery cover
and remove it
Remove the battery, right side first,
from the battery compartmen
Getting started
Installing handstrap
1.
2.
3.
Separate the velcro of the handstrap.
Feed the loose end of the extended handstrap through the handstrap clip
Wrap the handstrap around the clip and fasten together to close the strap
Calibrating screen
1.
2.
3.
For turn on the device 1st time
Follow the instructions on the welcome utility screen
Tap 5 crosses as appeared on the screen to calibrate the touch screen
Getting started Enabling & disabling WiFi
Enabling WiFi
1.
2.
3.
4.
Tap Start Menu, then tap and hold the Settings
Select Network Connections
Tap and hold AR6K_SD1 icon, make sure it is Enable
Double click the Network icon on the status bar, pick the desired AP and
setup as the wireless AP properties as usual
Disabling WiFi
1.
2.
3.
Tap Start Menu, then tap and hold the Settings
Select Network Connections
Tap and hold AR6K_SD1 icon, make sure it is Disable
Getting started Enabling & disabling BT
Enabling Bluetooth
1.
2.
3.
4.
5.
Tap Start Menu, then tap and hold the Settings
Select Control Panel
Double click Bluetooth Device Properties icon
Pick the Tools menu and then select Turn on Bluetooth item
Select Search Device and carry out bluetooth device operations as usual
Disabling Bluetooth
1.
2.
3.
4.
Tap Start Menu, then tap and hold the Settings
Select Control Panel
Double click Bluetooth Device Properties icon
Pick the Tools menu and then select Turn off Bluetooth item
Getting started Soft and hard reset
Performing soft reset
1.
Slide the battery latch to the left and grasp
the battery cover and remove it
2.
3.
Use a stylus to press the reset key and release
The device is reset
Performing hard reset
1.
Slide the battery latch to the left and grasp
the battery cover and remove it
2.
3.
4.
5.
Press “2” (or “8” if you want to format the
NAND flash as well) on the numeric keypad
Keep pressing the key, use a stylus to press
the reset key and release
When the green LED is flashing, release key “2”
or “8”
Put back the battery cover and calibrate the
screen
Reset key
Getting started Refreshing ROM
Refreshing LPT20 ROM
1.
2.
3.
4.
5.
6.
7.
8.
9.
Copy NK.bin, EBOOT.nb0 and splash.bin
(optional) to the root directory of the microSD
card
Open the battery cover, remove the battery
Insert the microSD card
Press and hold the left and right side Scan /
Action button
Install the battery to the battery compartment
Continue to press and hold the left and right
side Scan / Action button until the Update
Screen appears
Once NK.bin, EBOOT.nb0 and splash.bin
(optional ) have 100% complete updated.
Remove the battery and microSD card from
the device.
Insert the battery to the battery compartment
again
Performing the hard reset with NFLASH
format
Getting started Capturing data
65o
65o
Getting started Battery warning
Battery safety guidelines
1.
2.
3.
4.
5.
6.
7.
8.
9.
Use manufacturer’s original battery and charger only. Any incompatible
battery or charger may result in in a fire, explosion, or other hazard.
Do not disassemble or open, crush, bend or deform, puncture, or shred the
battery
Do not short circuit a battery by allowing conductive materials to contact the
battery terminals.
Charge the mobile device, the battery and charger temperatures must be
between 0 ºC and +40 ºC
Do not immerse or expose the battery to water or other liquids.
Do not dispose of batteries in fire or place the battery into a microwave oven
or dryer.
If battery leakage is found, avoid the liquid to come in contact with the skin or
eyes. If contact has been made, rinse the affected area with water and seek
medical advice.
If you suspect damage to your equipment or battery, contact the
manufacturer for inspection.
Follow the local regulations to dispose or recycle the used re-chargeable
batteries.
Statement of Compliance
CE Marking and European Economic Area (EEA)
Hereby, Portable Innovation Technology Ltd. declares that this product is in compliance with the
essential requirements and other relevant provisions of Directive, 1999/5/EC.
Radio Frequency Interference Requirements-FCC
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Warning
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The Equipment should be operated with minimum distance 1cm between the
radiator and user body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Joey Lau
Create Date                     : 2013:09:02 19:59:13+08:00
Modify Date                     : 2013:09:02 20:00:20+08:00
Language                        : ZH-HANS
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2013:09:02 20:00:20+08:00
Creator Tool                    : Acrobat PDFMaker 11 PowerPoint 版
Document ID                     : uuid:baca5803-e20b-48d7-9977-b99830089d1c
Instance ID                     : uuid:b31e974e-a133-4077-a1c9-36f9532947ee
Format                          : application/pdf
Title                           : PowerPoint Presentation
Creator                         : Joey Lau
Producer                        : Adobe PDF Library 11.0
Page Layout                     : SinglePage
Page Count                      : 14

EXIF Metadata provided by EXIF.tools