Jehe Technology Development SDM-S Embedded System User Manual
Shenzhen Jehe Technology Development Co.,Ltd. Embedded System
User manual
CPU
Intel® Atom x5-Z8350
Frequency
1.44 GHz (Up to 1.92 GHz)
BIOS
AMI Source Code
Chipset
SOC
System Memory
DDR3L 1600MHz, Onboard 2 GB
GPU
Intel® HD Graphics 400
Graphic Engine
DirectX11, OpenGL4.0 and OpenCL 1.2
Network Controller
Realtek RTL8111F Gigabit Ethernet
WiFi+BT on Board
RL-SM02BD-8723BS for WIFI+BT
Storage
eMMC Onboard 32GB
JAHC (Patented Tech)
WatchDog Timer, Auto Power On, RTC
Giada SDM-Z8350 Intel® SDM-S Atom Player
The product appearance, specifications and features are subject to change. Giada reserves the right of final interpretation for the content hereinabove.
USB
1 x USB3.0
Display Interface
1 x HDMI1.4b (Max. 2560 x 1600 @24Hz)
1 x DP1.1a (Max.4096 x 2304 @60Hz)
Serial Port
1 x COM
Dimensions
109.9mm x 60mm
Power Requirement
SDM I/O 12V/2A
Operation System
Windows 8.1/10 (64 Bit)/Android/Linux
Storage Temperature
-40 ~ 75°C (-40 ~ 167°F)
Operating Temperature
0 ~ 60°C (32 ~ 140°F)
Relative Humidity
95% @ 60°C(non-condensing)
Core System Mechanical and Environmental
Dimensions and Drawing
SDM I/O (PCIe x8 Edge Connector)
USB
2 x USB2.0
Ethernet
1 x RJ45
Rear I/O
Features
Intel® Cherry Trail Atom Z8350 Processors
Onboard 2GB DDR3L Memory
eMMC Onboard 32GB
SDM Standard I/O (1 x HDMI, 1 x DP, 1 x USB3.0,
1 x COM)
2 x USB2.0
1 x RJ45, Onboard WiFi/BT
SDM-Z8350
CPU: x5-Z8350, RAM: 2GB
1 x HDMI (SDM I/O), 1 x DP (SDM I/O)
1 x COM(SDM I/O),1 x RJ45
1 x USB3.0 (SDM I/O), 2 x USB2.0
eMMC Onboard 32GB
Ordering Information
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning statements: Minumum 20 cm distance must be maintaned between transmitter and users during
normal operations