Johnson Controls Interiors SAHL5 Universal Garage Door Opener Transmitter User Manual CHRY OM Contenta pu

Johnson Controls Interiors L.L.C. Universal Garage Door Opener Transmitter CHRY OM Contenta pu

manual

JOBNAME: CHRY OM (Contenta pu PAGE: 1 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 254B7795/chry_pdm/chrysler/owners/ctx/sim03.40.00GARAGE DOOR OPENER — EVICHomeLinktreplaces up to three hand-held transmittersthat operate devices such as garage door openers, motor-ized gates, lighting or home security systems. TheHomeLinktunit is powered by your vehicles 12 Voltbattery.The HomeLinktbuttons that are located in the overheadconsole designate the three different HomeLinktchan-nels.NOTE: HomeLinktis disabled when the Vehicle Secu-rity Alarm is active.Before You Begin Programming HomeLinkTBe sure that your vehicle is parked outside of the garagebefore you begin programming.HomeLinktButtons1art=033906001.tif NO TRANS
JOBNAME: CHRY OM (Contenta pu PAGE: 2 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 23A213ED/chry_pdm/chrysler/owners/ctx/sim03.40.00For more efficient programming and accurate transmis-sion of the radio-frequency signal it is recommended thata new battery be placed in the hand-held transmitter ofthe device that is being programmed to the HomeLinktsystem.Erase all channels before you begin programming. Toerase the channels place the ignition in the ON/RUNposition and press and hold the two outside HomeLinktbuttons (I and III) for up 20 seconds. The ElectronicVehicle Information Center (EVIC) will display “CLEAR-ING CHANNELS”. Release the buttons when the EVICdisplays “CHANNELS CLEARED”.NOTE:•Erasing all channels should only be performed whenprogramming HomeLinktfor the first time. Do noterase channels when programming additional buttons.•If you have any problems, or require assistance, pleasecall toll-free 1–800–355–3515 or, on the Internet atwww.HomeLink.com for information or assistance.Programming A Rolling CodeFor programming garage door openers that were manu-factured after 1995. These garage door openers can beidentified by the “LEARN” or “TRAIN” button locatedwhere the hanging antenna is attached to the garage dooropener. It is NOT the button that is normally used toopen and close the door. The name and color of thebutton may vary by manufacturer.2
JOBNAME: CHRY OM (Contenta pu PAGE: 3 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1C395F54/chry_pdm/chrysler/owners/ctx/sim03.40.001. Turn the ignition switch to the ON/RUN position.2. Place the hand-held transmitter 1 to 3 inches (3 to8 cm) away from the HomeLinktbutton you wish toprogram.3. Simultaneously press and hold both the Homelinktbutton you want to program and the hand-held transmit-ter button.4. Continue to hold buttons until the EVIC displaychanges from “CHANNEL # TRAINING” to “CHAN-NEL # TRAINED”, then release both buttons.NOTE:•It may take up to 30 seconds or longer in some casedfor the channel to train.•If the EVIC displays “DID NOT TRAIN” repeat fromStep 2.5. At the garage door opener motor (in the garage),locate the “LEARN” or “TRAINING” button. This canusually be found where the hanging antenna wire isattached to the garage door opener/device motor. Firmlypress and release the “LEARN” or “TRAINING” button.Training The Garage Door Opener1 — Door Opener2 — Training Button3art=034000356.tif NO TRANS
JOBNAME: CHRY OM (Contenta pu PAGE: 4 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 2125D1AA/chry_pdm/chrysler/owners/ctx/sim03.40.00On some garage door openers/devices there may be alight that blinks when the garage door opener/device isin the LEARN/TRAIN mode.NOTE: You have 30 seconds in which to initiate the nextstep after the LEARN button has been pressed.6. Return to the vehicle and press the programmedHomeLinktbutton twice (holding the button for twoseconds each time). The EVIC will display “CHANNEL #TRANSMIT”. If the garage door opener/device activates,programming is complete.NOTE: If the garage door opener/device does notactivate, press the button a third time (for two seconds) tocomplete the training.To program the remaining two HomeLinktbuttons,repeat each step for each remaining button. DO NOTerase the channels.Reprogramming A Single HomeLinktButtonTo reprogram a channel that has been previously trained,follow these steps:1. Turn the ignition switch to the ON/RUN position.2. Press and hold the desired HomeLinktbutton untilthe EVIC displays “CHANNEL # TRAINING” Do notrelease the button.3. Without releasing the button proceed with “Program-ming A Rolling Code” Step 2 and follow all remainingsteps.Programming A Non-Rolling CodeFor programming Garage Door Openers manufacturedbefore 1995.1. Turn the ignition switch to the ON/RUN position.4
JOBNAME: CHRY OM (Contenta pu PAGE: 5 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1A86A505/chry_pdm/chrysler/owners/ctx/sim03.40.002. Place the hand-held transmitter 1 to 3 inches (3 to8 cm) away from the HomeLinktbutton you wish toprogram.3. Simultaneously press and hold both the Homelinktbutton you want to program and the hand-held transmit-ter button.4. Continue to hold buttons until the EVIC displaychanges from “CHANNEL # TRAINING” to “CHAN-NEL # TRAINED”, then release both buttons.NOTE:•It may take up to 30 seconds or longer in some casedfor the channel to train.•If the EVIC displays “DID NOT TRAIN” repeat fromStep 2.5. Press and hold the programmed HomeLinktbutton.The EVIC will display “CHANNEL # TRANSMIT”. If thegarage door opener/device activates, programming iscomplete.To program the remaining two HomeLinktbuttons,repeat each step for each remaining button. DO NOTerase the channels.Reprogramming A Single HomeLinktButtonTo reprogram a channel that has been previously trained,follow these steps:1. Turn the ignition switch to the ON/RUN position.2. Press and hold the desired HomeLinktbutton untilthe EVIC displays “CHANNEL # TRAINING” Do notrelease the button.3. Without releasing the button proceed with “Program-ming A Non-Rolling Code” Step 2 and follow all remain-ing steps.5
JOBNAME: CHRY OM (Contenta pu PAGE: 6 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 27782D88/chry_pdm/chrysler/owners/ctx/sim03.40.00Canadian/Gate Operator ProgrammingFor programming transmitters in Canada/United Statesthat require the transmitter signals to “time-out” afterseveral seconds of transmission.Canadian radio frequency laws require transmitter sig-nals to time-out (or quit) after several seconds of trans-mission – which may not be long enough for HomeLinktto pick up the signal during programming. Similar to thisCanadian law, some U.S. gate operators are designed totime-out in the same manner.It may be helpful to unplug the device during the cyclingprocess to prevent possible overheating of the garagedoor or gate motor.1. Turn the ignition switch to the ON/RUN position.2. Place the hand-held transmitter 1 to 3 inches (3 to8 cm) away from the HomeLinktbutton you wish toprogram.3. Simultaneously press and hold both the Homelinktbutton while you press and release (“cycle”), your hand-held transmitter every two seconds.4. Continue to hold buttons until the EVIC displaychanges from “CHANNEL # TRAINING” to “CHAN-NEL # TRAINED”, then release both buttons.NOTE:•It may take up to 30 seconds or longer in some casedfor the channel to train.•If the EVIC displays “DID NOT TRAIN” repeat fromStep 2.5. Press and hold the programmed HomeLinktbutton.The EVIC will display “CHANNEL # TRANSMIT”. If thedevice is plugged in and activates, programming iscomplete.If you unplugged the garage door opener/device forprogramming, plug it back in at this time.6
JOBNAME: CHRY OM (Contenta pu PAGE: 7 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 279ADD84/chry_pdm/chrysler/owners/ctx/sim03.40.00Reprogramming A Single HomeLinktButtonTo reprogram a channel that has been previously trained,follow these steps:1. Turn the ignition switch to the ON/RUN position.2. Press and hold the desired HomeLinktbutton untilthe EVIC displays “CHANNEL # TRAINING” Do notrelease the button.3. Without releasing the button proceed with“Canadian/Gate Operator Programming” Step 2 andfollow all remaining steps.Using HomeLinkTTo operate, press and release the programmedHomeLinktbutton. Activation will now occur for theprogrammed device (i.e., garage door opener, gate opera-tor, security system, entry door lock, home/office light-ing, etc.,). The hand-held transmitter of the device mayalso be used at any time.SecurityIt is advised to erase all channels before you sell or turnin your vehicle.To erase the channels press and hold the two outsideHomeLinktbuttons (I and III) for up 20 seconds. TheElectronic Vehicle Information Center (EVIC) will display“CLEARING CHANNELS”. Release the buttons whenthe EVIC displays “CHANNELS CLEARED”.The HomeLinktUniversal Transceiver is disabled whenthe Vehicle Security Alarm is active.Troubleshooting TipsIf you are having trouble programming HomeLinkt, hereare some of the most common solutions:•Replace the battery in the original hand-held transmit-ter.•Press the LEARN button on the Garage Door Openerto complete the training for a Rolling Code.7
JOBNAME: CHRY OM (Contenta pu PAGE: 8 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1C5C7460/chry_pdm/chrysler/owners/ctx/sim03.40.00•Did you unplug the device for programming andremember to plug it back in?If you have any problems, or require assistance, pleasecall toll-free 1–800–355–3515 or, on the Internet atwww.HomeLink.com for information or assistance.WARNING!•Your motorized door or gate will open and closewhile you are programming the universal trans-ceiver. Do not program the transceiver if people,pets or other objects are in the path of the door orgate. Only use this transceiver with a garage dooropener that has a “stop and reverse” feature asrequired by Federal safety standards. This in-cludes most garage door opener models manufac-tured after 1982. Do not use a garage door openerwithout these safety features. Call toll-free 1–800–355–3515 or, on the Internet atwww.HomeLink.com for safety information or as-sistance.•Vehicle exhaust contains carbon monoxide, a dan-gerous gas. Do not run your vehicle in the garagewhile programming the transceiver. Exhaust gascan cause serious injury or death.8
JOBNAME: CHRY OM (Contenta pu PAGE: 9 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 246DACD9/chry_pdm/chrysler/owners/ctx/sim03.40.00General InformationThis device complies with FCC rules Part 15 and IndustryCanada RSS-210. Operation is subject to the followingtwo conditions:1. This device may not cause harmful interference.2. This device must accept any interference that may bereceived including interference that may cause undesiredoperation.NOTE:•The transmitter has been tested and it complies withFCC and IC rules. Changes or modifications notexpressly approved by the party responsible for com-pliance could void the user’s authority to operate thedevice.•The term IC before the certification/registration num-ber only signifies that Industry Canada technicalspecifications were met.GARAGE DOOR OPENER — LEDHomeLinktreplaces up to three hand-held transmittersthat operate devices such as garage door openers, motor-ized gates, lighting or home security systems. TheHomeLinktunit is powered by your vehicles 12 Voltbattery.The HomeLinktbuttons, located on either the overheadconsole, headliner or sunvisor, designate the three differ-ent HomeLinktchannels. The HomeLinktindicator islocated above the center button.9
JOBNAME: CHRY OM (Contenta pu PAGE: 10 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 118EAD14/chry_pdm/chrysler/owners/ctx/sim03.40.00NOTE: HomeLinktis disabled when the Vehicle Secu-rity Alarm is active.Before You Begin Programming HomeLinkTBe sure that your vehicle is parked outside of the garagebefore you begin programming.HomeLinktButtons/Overhead Consoles HomeLinktButtons/Sunvisor/Headliner10art=034033576.tif NO TRANS art=034000355.tif NO TRANS
JOBNAME: CHRY OM (Contenta pu PAGE: 11 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1EFEE841/chry_pdm/chrysler/owners/ctx/sim03.40.00For more efficient programming and accurate transmis-sion of the radio-frequency signal it is recommended thata new battery be placed in the hand-held transmitter ofthe device that is being programmed to the HomeLinktsystem.Erase all channels before you begin programming. Toerase the channels place the ignition in the ON/RUNposition and press and hold the two outside HomeLinktbuttons (I and III) for up 20 seconds or until the redindicator flashes.NOTE:•Erasing all channels should only be performed whenprogramming HomeLinktfor the first time. Do noterase channels when programming additional buttons.•If you have any problems, or require assistance, pleasecall toll-free 1–800–355–3515 or, on the Internet atwww.HomeLink.com for information or assistance.Programming A Rolling CodeFor programming garage door openers that were manu-factured after 1995. These garage door openers can beidentified by the “LEARN” or “TRAIN” button locatedwhere the hanging antenna is attached to the garage dooropener. It is NOT the button that is normally used toopen and close the door. The name and color of thebutton may vary by manufacturer.11
JOBNAME: CHRY OM (Contenta pu PAGE: 12 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 24986E04/chry_pdm/chrysler/owners/ctx/sim03.40.001. Turn the ignition switch to the ON/RUN position.2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)away from the HomeLinktbutton you wish to programwhile keeping the HomeLinktindicator light in view.3. Simultaneously press and hold both the Homelinktbutton you want to program and the hand-held transmit-ter button.4. Continue to hold both buttons and observe the indi-cator light. The Homelinktindicator will flash slowlyand then rapidly after Homelinkthas received the fre-quency signal from the hand-held transmitter. Releaseboth buttons after the indicator light changes from slowto rapid.5. At the garage door opener motor (in the garage),locate the “LEARN” or “TRAINING” button. This canusually be found where the hanging antenna wire isattached to the garage door opener/device motor. Firmlypress and release the “LEARN” or “TRAINING” button.On some garage door openers/devices there may be alight that blinks when the garage door opener/device isin the LEARN/TRAIN mode.Training The Garage Door Opener1 — Door Opener2 — Training Button12art=034000356.tif NO TRANS
JOBNAME: CHRY OM (Contenta pu PAGE: 13 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 2310549F/chry_pdm/chrysler/owners/ctx/sim03.40.00NOTE: You have 30 seconds in which to initiate the nextstep after the LEARN button has been pressed.6. Return to the vehicle and press the programmedHomeLinktbutton twice (holding the button for twoseconds each time). If the garage door opener/deviceactivates, programming is complete.NOTE: If the garage door opener/device does notactivate, press the button a third time (for two seconds) tocomplete the training.To program the remaining two HomeLinktbuttons,repeat each step for each remaining button. DO NOTerase the channels.Reprogramming A Single HomeLinktButtonTo reprogram a channel that has been previously trained,follow these steps:1. Turn the ignition switch to the ON/RUN position.2. Press and hold the desired HomeLinktbutton untilthe indicator light begins to flash after 20 seconds. Do notrelease the button.3. Without releasing the button proceed with “Program-ming A Rolling Code” Step 2 and follow all remainingsteps.Programming A Non-Rolling CodeFor programming Garage Door Openers manufacturedbefore 1995.1. Turn the ignition switch to the ON/RUN position.2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)away from the HomeLinktbutton you wish to programwhile keeping the HomeLinktindicator light in view.3. Simultaneously press and hold both the Homelinktbutton you want to program and the hand-held transmit-ter button.13
JOBNAME: CHRY OM (Contenta pu PAGE: 14 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 27953FD0/chry_pdm/chrysler/owners/ctx/sim03.40.004. Continue to hold both buttons and observe the indi-cator light. The Homelinktindicator will flash slowlyand then rapidly after Homelinkthas received the fre-quency signal from the hand-held transmitter. Releaseboth buttons after the indicator light changes from slowto rapid.5. Press and hold the programmed HomeLinktbuttonand observe the indicator light.•If the indicator light stays on constantly, program-ming is complete and the garage door/deviceshould activate when the HomeLinktbutton ispressed.•To program the two remaining HomeLinktbuttons,repeat each step for each remaining button. DONOT erase the channels.Reprogramming A Single HomeLinktButtonTo reprogram a channel that has been previously trained,follow these steps:1. Turn the ignition switch to the ON/RUN position.2. Press and hold the desired HomeLinktbutton untilthe indicator light begins to flash after 20 seconds. Do notrelease the button.3. Without releasing the button proceed with “Program-ming A Non-Rolling Code” Step 2 and follow all remain-ing steps.Canadian/Gate Operator ProgrammingFor programming transmitters in Canada/United Statesthat require the transmitter signals to “time-out” afterseveral seconds of transmission.Canadian radio frequency laws require transmitter sig-nals to time-out (or quit) after several seconds of trans-mission – which may not be long enough for HomeLinkt14
JOBNAME: CHRY OM (Contenta pu PAGE: 15 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 2239A4BC/chry_pdm/chrysler/owners/ctx/sim03.40.00to pick up the signal during programming. Similar to thisCanadian law, some U.S. gate operators are designed totime-out in the same manner.It may be helpful to unplug the device during the cyclingprocess to prevent possible overheating of the garagedoor or gate motor.1. Turn the ignition switch to the ON/RUN position.2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)away from the HomeLinktbutton you wish to programwhile keeping the HomeLinktindicator light in view.3. Continue to press and hold the HomeLinktbutton,while you press and release (“cycle”), your hand-heldtransmitter every two seconds until HomeLinkthassuccessfully accepted the frequency signal. The indicatorlight will flash slowly and then rapidly when fullytrained.4. Watch for the HomeLinktindicator to change flashrates. When it changes, it is programmed. It may take upto 30 seconds or longer in rare cases. The garage doormay open and close while you are programming.5. Press and hold the programmed HomeLinktbuttonand observe the indicator light.•If the indicator light stays on constantly, program-ming is complete and the garage door/deviceshould activate when the HomeLinktbutton ispressed.•To program the two remaining HomeLinktbuttons,repeat each step for each remaining button. DONOT erase the channels.If you unplugged the garage door opener/device forprogramming, plug it back in at this time.15
JOBNAME: CHRY OM (Contenta pu PAGE: 16 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 28DC2BF8/chry_pdm/chrysler/owners/ctx/sim03.40.00Reprogramming A Single HomeLinktButtonTo reprogram a channel that has been previously trained,follow these steps:1. Turn the ignition switch to the ON/RUN position.2. Press and hold the desired HomeLinktbutton untilthe indicator light begins to flash after 20 seconds. Do notrelease the button.3. Without releasing the button proceed with“Canadian/Gate Operator Programming” Step 2 andfollow all remaining steps.Using HomeLinkTTo operate, press and release the programmedHomeLinktbutton. Activation will now occur for theprogrammed device (i.e., garage door opener, gate opera-tor, security system, entry door lock, home/office light-ing, etc.,). The hand-held transmitter of the device mayalso be used at any time.SecurityIt is advised to erase all channels before you sell or turnin your vehicle.To do this, press and hold the two outside buttons for20 seconds until the red indicator flashes. Note that allchannels will be erased. Individual channels cannot beerased.The HomeLinktUniversal Transceiver is disabled whenthe Vehicle Security Alarm is active.Troubleshooting TipsIf you are having trouble programming HomeLinkt, hereare some of the most common solutions:•Replace the battery in the original hand-held transmit-ter.•Press the LEARN button on the Garage Door Openerto complete the training for a Rolling Code.16
JOBNAME: CHRY OM (Contenta pu PAGE: 17 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 199A08F0/chry_pdm/chrysler/owners/ctx/sim03.40.00•Did you unplug the device for programming andremember to plug it back in?If you have any problems, or require assistance, pleasecall toll-free 1–800–355–3515 or, on the Internet atwww.HomeLink.com for information or assistance.WARNING!•Your motorized door or gate will open and closewhile you are programming the universal trans-ceiver. Do not program the transceiver if people,pets or other objects are in the path of the door orgate. Only use this transceiver with a garage dooropener that has a “stop and reverse” feature asrequired by Federal safety standards. This in-cludes most garage door opener models manufac-tured after 1982. Do not use a garage door openerwithout these safety features. Call toll-free 1–800–355–3515 or, on the Internet atwww.HomeLink.com for safety information or as-sistance.•Vehicle exhaust contains carbon monoxide, a dan-gerous gas. Do not run your vehicle in the garagewhile programming the transceiver. Exhaust gascan cause serious injury or death.17
JOBNAME: CHRY OM (Contenta pu PAGE: 18 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1E9E26C3/chry_pdm/chrysler/owners/ctx/sim03.40.00General InformationThis device complies with FCC rules Part 15 and IndustryCanada RSS-210. Operation is subject to the followingtwo conditions:1. This device may not cause harmful interference.2. This device must accept any interference that may bereceived including interference that may cause undesiredoperation.NOTE:•The transmitter has been tested and it complies withFCC and IC rules. Changes or modifications notexpressly approved by the party responsible for com-pliance could void the user’s authority to operate thedevice.•The term IC before the certification/registration num-ber only signifies that Industry Canada technicalspecifications were met.18

Navigation menu