Johnson Controls Interiors SAHL5 Universal Garage Door Opener Transmitter User Manual CHRY OM Contenta pu

Johnson Controls Interiors L.L.C. Universal Garage Door Opener Transmitter CHRY OM Contenta pu

manual

Download: Johnson Controls Interiors SAHL5 Universal Garage Door Opener Transmitter User Manual CHRY OM  Contenta pu
Mirror Download [FCC.gov]Johnson Controls Interiors SAHL5 Universal Garage Door Opener Transmitter User Manual CHRY OM  Contenta pu
Document ID1635140
Application IDwwouopT/ZhOfy70PsYtATQ==
Document Descriptionmanual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize57.17kB (714571 bits)
Date Submitted2012-02-10 00:00:00
Date Available2012-02-13 00:00:00
Creation Date2012-01-03 09:31:46
Producing SoftwareGPL Ghostscript 8.63
Document Lastmod2012-01-03 10:18:27
Document TitleCHRY OM (Contenta pu
Document CreatorXyEnterprise XPP 8.3C.1 SP #2

JOBNAME: CHRY OM (Contenta pu PAGE: 1 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 254B7795
/chry_pdm/chrysler/owners/ctx/sim03.40.00
GARAGE DOOR OPENER — EVIC
HomeLinkt replaces up to three hand-held transmitters
that operate devices such as garage door openers, motorized gates, lighting or home security systems. The
HomeLinkt unit is powered by your vehicles 12 Volt
battery.
art=033906001.tif
NO TRANS
The HomeLinkt buttons that are located in the overhead
console designate the three different HomeLinkt channels.
HomeLinkt Buttons
NOTE: HomeLinkt is disabled when the Vehicle Security Alarm is active.
Before You Begin Programming HomeLinkT
Be sure that your vehicle is parked outside of the garage
before you begin programming.
JOBNAME: CHRY OM (Contenta pu PAGE: 2 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 23A213ED
/chry_pdm/chrysler/owners/ctx/sim03.40.00
For more efficient programming and accurate transmis- • If you have any problems, or require assistance, please
sion of the radio-frequency signal it is recommended that
call toll-free 1–800–355–3515 or, on the Internet at
a new battery be placed in the hand-held transmitter of
www.HomeLink.com for information or assistance.
the device that is being programmed to the HomeLinkt
Programming A Rolling Code
system.
For programming garage door openers that were manuErase all channels before you begin programming. To factured after 1995. These garage door openers can be
erase the channels place the ignition in the ON/RUN identified by the “LEARN” or “TRAIN” button located
position and press and hold the two outside HomeLinkt where the hanging antenna is attached to the garage door
buttons (I and III) for up 20 seconds. The Electronic opener. It is NOT the button that is normally used to
Vehicle Information Center (EVIC) will display “CLEAR- open and close the door. The name and color of the
ING CHANNELS”. Release the buttons when the EVIC button may vary by manufacturer.
displays “CHANNELS CLEARED”.
NOTE:
• Erasing all channels should only be performed when
programming HomeLinkt for the first time. Do not
erase channels when programming additional buttons.
JOBNAME: CHRY OM (Contenta pu PAGE: 3 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1C395F54
/chry_pdm/chrysler/owners/ctx/sim03.40.00
art=034000356.tif
NO TRANS
3. Simultaneously press and hold both the Homelinkt
button you want to program and the hand-held transmitter button.
4. Continue to hold buttons until the EVIC display
changes from “CHANNEL # TRAINING” to “CHANNEL # TRAINED”, then release both buttons.
NOTE:
• It may take up to 30 seconds or longer in some cased
for the channel to train.
Training The Garage Door Opener
• If the EVIC displays “DID NOT TRAIN” repeat from
Step 2.
5. At the garage door opener motor (in the garage),
locate the “LEARN” or “TRAINING” button. This can
usually be found where the hanging antenna wire is
1. Turn the ignition switch to the ON/RUN position.
attached to the garage door opener/device motor. Firmly
2. Place the hand-held transmitter 1 to 3 inches (3 to press and release the “LEARN” or “TRAINING” button.
8 cm) away from the HomeLinkt button you wish to
program.
1 — Door Opener
2 — Training Button
JOBNAME: CHRY OM (Contenta pu PAGE: 4 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 2125D1AA
/chry_pdm/chrysler/owners/ctx/sim03.40.00
On some garage door openers/devices there may be a Reprogramming A Single HomeLinkt Button
light that blinks when the garage door opener/device is To reprogram a channel that has been previously trained,
in the LEARN/TRAIN mode.
follow these steps:
NOTE: You have 30 seconds in which to initiate the next 1. Turn the ignition switch to the ON/RUN position.
step after the LEARN button has been pressed.
2. Press and hold the desired HomeLinkt button until
6. Return to the vehicle and press the programmed the EVIC displays “CHANNEL # TRAINING” Do not
HomeLinkt button twice (holding the button for two release the button.
seconds each time). The EVIC will display “CHANNEL #
3. Without releasing the button proceed with “ProgramTRANSMIT”. If the garage door opener/device activates,
ming A Rolling Code” Step 2 and follow all remaining
programming is complete.
steps.
NOTE: If the garage door opener/device does not
Programming A Non-Rolling Code
activate, press the button a third time (for two seconds) to
For programming Garage Door Openers manufactured
complete the training.
before 1995.
To program the remaining two HomeLinkt buttons,
1. Turn the ignition switch to the ON/RUN position.
repeat each step for each remaining button. DO NOT
erase the channels.
JOBNAME: CHRY OM (Contenta pu PAGE: 5 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1A86A505
/chry_pdm/chrysler/owners/ctx/sim03.40.00
2. Place the hand-held transmitter 1 to 3 inches (3 to 5. Press and hold the programmed HomeLinkt button.
8 cm) away from the HomeLinkt button you wish to The EVIC will display “CHANNEL # TRANSMIT”. If the
garage door opener/device activates, programming is
program.
complete.
3. Simultaneously press and hold both the Homelinkt
button you want to program and the hand-held transmit- To program the remaining two HomeLinkt buttons,
repeat each step for each remaining button. DO NOT
ter button.
erase the channels.
4. Continue to hold buttons until the EVIC display
changes from “CHANNEL # TRAINING” to “CHAN- Reprogramming A Single HomeLinkt Button
NEL # TRAINED”, then release both buttons.
To reprogram a channel that has been previously trained,
follow these steps:
NOTE:
• It may take up to 30 seconds or longer in some cased 1. Turn the ignition switch to the ON/RUN position.
for the channel to train.
2. Press and hold the desired HomeLinkt button until
• If the EVIC displays “DID NOT TRAIN” repeat from the EVIC displays “CHANNEL # TRAINING” Do not
release the button.
Step 2.
3. Without releasing the button proceed with “Programming A Non-Rolling Code” Step 2 and follow all remaining steps.
JOBNAME: CHRY OM (Contenta pu PAGE: 6 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 27782D88
/chry_pdm/chrysler/owners/ctx/sim03.40.00
Canadian/Gate Operator Programming
3. Simultaneously press and hold both the Homelinkt
For programming transmitters in Canada/United States button while you press and release (“cycle”), your handthat require the transmitter signals to “time-out” after held transmitter every two seconds.
several seconds of transmission.
4. Continue to hold buttons until the EVIC display
Canadian radio frequency laws require transmitter sig- changes from “CHANNEL # TRAINING” to “CHANnals to time-out (or quit) after several seconds of trans- NEL # TRAINED”, then release both buttons.
mission – which may not be long enough for HomeLinkt
NOTE:
to pick up the signal during programming. Similar to this
• It may take up to 30 seconds or longer in some cased
Canadian law, some U.S. gate operators are designed to
for the channel to train.
time-out in the same manner.
• If the EVIC displays “DID NOT TRAIN” repeat from
It may be helpful to unplug the device during the cycling
Step 2.
process to prevent possible overheating of the garage
5. Press and hold the programmed HomeLinkt button.
door or gate motor.
The EVIC will display “CHANNEL # TRANSMIT”. If the
1. Turn the ignition switch to the ON/RUN position.
device is plugged in and activates, programming is
2. Place the hand-held transmitter 1 to 3 inches (3 to complete.
8 cm) away from the HomeLinkt button you wish to
If you unplugged the garage door opener/device for
program.
programming, plug it back in at this time.
JOBNAME: CHRY OM (Contenta pu PAGE: 7 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 279ADD84
/chry_pdm/chrysler/owners/ctx/sim03.40.00
Reprogramming A Single HomeLinkt Button
Security
To reprogram a channel that has been previously trained, It is advised to erase all channels before you sell or turn
in your vehicle.
follow these steps:
To erase the channels press and hold the two outside
HomeLinkt buttons (I and III) for up 20 seconds. The
2. Press and hold the desired HomeLinkt button until
Electronic Vehicle Information Center (EVIC) will display
the EVIC displays “CHANNEL # TRAINING” Do not
“CLEARING CHANNELS”. Release the buttons when
release the button.
the EVIC displays “CHANNELS CLEARED”.
3. Without releasing the button proceed with
The HomeLinkt Universal Transceiver is disabled when
“Canadian/Gate Operator Programming” Step 2 and
the Vehicle Security Alarm is active.
follow all remaining steps.
Troubleshooting Tips
Using HomeLinkT
If you are having trouble programming HomeLinkt, here
To operate, press and release the programmed
are some of the most common solutions:
HomeLinkt button. Activation will now occur for the
programmed device (i.e., garage door opener, gate opera- • Replace the battery in the original hand-held transmittor, security system, entry door lock, home/office lightter.
ing, etc.,). The hand-held transmitter of the device may
• Press the LEARN button on the Garage Door Opener
also be used at any time.
to complete the training for a Rolling Code.
1. Turn the ignition switch to the ON/RUN position.
JOBNAME: CHRY OM (Contenta pu PAGE: 8 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1C5C7460
/chry_pdm/chrysler/owners/ctx/sim03.40.00
• Did you unplug the device for programming and
remember to plug it back in?
If you have any problems, or require assistance, please
call toll-free 1–800–355–3515 or, on the Internet at
www.HomeLink.com for information or assistance.
WARNING!
• Your motorized door or gate will open and close
while you are programming the universal transceiver. Do not program the transceiver if people,
pets or other objects are in the path of the door or
gate. Only use this transceiver with a garage door
opener that has a “stop and reverse” feature as
required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener
without these safety features. Call toll-free 1–800–
355–3515
or,
on
the
Internet
at
www.HomeLink.com for safety information or assistance.
• Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage
while programming the transceiver. Exhaust gas
can cause serious injury or death.
JOBNAME: CHRY OM (Contenta pu PAGE: 9 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 246DACD9
/chry_pdm/chrysler/owners/ctx/sim03.40.00
General Information
This device complies with FCC rules Part 15 and Industry
Canada RSS-210. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
GARAGE DOOR OPENER — LED
HomeLinkt replaces up to three hand-held transmitters
that operate devices such as garage door openers, motorized gates, lighting or home security systems. The
HomeLinkt unit is powered by your vehicles 12 Volt
battery.
2. This device must accept any interference that may be The HomeLinkt buttons, located on either the overhead
received including interference that may cause undesired console, headliner or sunvisor, designate the three different HomeLinkt channels. The HomeLinkt indicator is
operation.
located above the center button.
NOTE:
• The transmitter has been tested and it complies with
FCC and IC rules. Changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority to operate the
device.
• The term IC before the certification/registration number only signifies that Industry Canada technical
specifications were met.
JOBNAME: CHRY OM (Contenta pu PAGE: 10 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 118EAD14
/chry_pdm/chrysler/owners/ctx/sim03.40.00
10
art=034033576.tif
NO TRANS
HomeLinkt Buttons/Overhead Consoles
art=034000355.tif
NO TRANS
HomeLinkt Buttons/Sunvisor/Headliner
NOTE: HomeLinkt is disabled when the Vehicle Security Alarm is active.
Before You Begin Programming HomeLinkT
Be sure that your vehicle is parked outside of the garage
before you begin programming.
JOBNAME: CHRY OM (Contenta pu PAGE: 11 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1EFEE841
/chry_pdm/chrysler/owners/ctx/sim03.40.00
11
Programming A Rolling Code
For programming garage door openers that were manufactured after 1995. These garage door openers can be
identified by the “LEARN” or “TRAIN” button located
where the hanging antenna is attached to the garage door
opener. It is NOT the button that is normally used to
Erase all channels before you begin programming. To
open and close the door. The name and color of the
erase the channels place the ignition in the ON/RUN
button may vary by manufacturer.
position and press and hold the two outside HomeLinkt
buttons (I and III) for up 20 seconds or until the red
indicator flashes.
For more efficient programming and accurate transmission of the radio-frequency signal it is recommended that
a new battery be placed in the hand-held transmitter of
the device that is being programmed to the HomeLinkt
system.
NOTE:
• Erasing all channels should only be performed when
programming HomeLinkt for the first time. Do not
erase channels when programming additional buttons.
• If you have any problems, or require assistance, please
call toll-free 1–800–355–3515 or, on the Internet at
www.HomeLink.com for information or assistance.
JOBNAME: CHRY OM (Contenta pu PAGE: 12 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 24986E04
/chry_pdm/chrysler/owners/ctx/sim03.40.00
12
art=034000356.tif
NO TRANS
3. Simultaneously press and hold both the Homelinkt
button you want to program and the hand-held transmitter button.
4. Continue to hold both buttons and observe the indicator light. The Homelinkt indicator will flash slowly
and then rapidly after Homelinkt has received the frequency signal from the hand-held transmitter. Release
both buttons after the indicator light changes from slow
to rapid.
5. At the garage door opener motor (in the garage),
locate the “LEARN” or “TRAINING” button. This can
Training The Garage Door Opener
usually be found where the hanging antenna wire is
attached to the garage door opener/device motor. Firmly
1 — Door Opener
2 — Training Button
press and release the “LEARN” or “TRAINING” button.
On some garage door openers/devices there may be a
1. Turn the ignition switch to the ON/RUN position.
light that blinks when the garage door opener/device is
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) in the LEARN/TRAIN mode.
away from the HomeLinkt button you wish to program
while keeping the HomeLinkt indicator light in view.
JOBNAME: CHRY OM (Contenta pu PAGE: 13 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 2310549F
/chry_pdm/chrysler/owners/ctx/sim03.40.00
13
NOTE: You have 30 seconds in which to initiate the next 2. Press and hold the desired HomeLinkt button until
step after the LEARN button has been pressed.
the indicator light begins to flash after 20 seconds. Do not
release the button.
6. Return to the vehicle and press the programmed
HomeLinkt button twice (holding the button for two 3. Without releasing the button proceed with “Programseconds each time). If the garage door opener/device ming A Rolling Code” Step 2 and follow all remaining
activates, programming is complete.
steps.
NOTE: If the garage door opener/device does not Programming A Non-Rolling Code
activate, press the button a third time (for two seconds) to For programming Garage Door Openers manufactured
complete the training.
before 1995.
To program the remaining two HomeLinkt buttons, 1. Turn the ignition switch to the ON/RUN position.
repeat each step for each remaining button. DO NOT
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)
erase the channels.
away from the HomeLinkt button you wish to program
Reprogramming A Single HomeLinkt Button
while keeping the HomeLinkt indicator light in view.
To reprogram a channel that has been previously trained,
3. Simultaneously press and hold both the Homelinkt
follow these steps:
button you want to program and the hand-held transmit1. Turn the ignition switch to the ON/RUN position.
ter button.
JOBNAME: CHRY OM (Contenta pu PAGE: 14 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 27953FD0
/chry_pdm/chrysler/owners/ctx/sim03.40.00
14
4. Continue to hold both buttons and observe the indicator light. The Homelinkt indicator will flash slowly
and then rapidly after Homelinkt has received the frequency signal from the hand-held transmitter. Release
both buttons after the indicator light changes from slow
to rapid.
Reprogramming A Single HomeLinkt Button
To reprogram a channel that has been previously trained,
follow these steps:
1. Turn the ignition switch to the ON/RUN position.
2. Press and hold the desired HomeLinkt button until
the indicator light begins to flash after 20 seconds. Do not
5. Press and hold the programmed HomeLinkt button
release the button.
and observe the indicator light.
3. Without releasing the button proceed with “Program• If the indicator light stays on constantly, programming A Non-Rolling Code” Step 2 and follow all remainming is complete and the garage door/device
ing steps.
should activate when the HomeLinkt button is
pressed.
Canadian/Gate Operator Programming
For programming transmitters in Canada/United States
• To program the two remaining HomeLinkt buttons,
that require the transmitter signals to “time-out” after
repeat each step for each remaining button. DO
several seconds of transmission.
NOT erase the channels.
Canadian radio frequency laws require transmitter signals to time-out (or quit) after several seconds of transmission – which may not be long enough for HomeLinkt
JOBNAME: CHRY OM (Contenta pu PAGE: 15 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 2239A4BC
/chry_pdm/chrysler/owners/ctx/sim03.40.00
15
to pick up the signal during programming. Similar to this 4. Watch for the HomeLinkt indicator to change flash
Canadian law, some U.S. gate operators are designed to rates. When it changes, it is programmed. It may take up
time-out in the same manner.
to 30 seconds or longer in rare cases. The garage door
may open and close while you are programming.
It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage 5. Press and hold the programmed HomeLinkt button
door or gate motor.
and observe the indicator light.
1. Turn the ignition switch to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)
away from the HomeLinkt button you wish to program
while keeping the HomeLinkt indicator light in view.
• If the indicator light stays on constantly, programming is complete and the garage door/device
should activate when the HomeLinkt button is
pressed.
• To program the two remaining HomeLinkt buttons,
3. Continue to press and hold the HomeLinkt button,
repeat each step for each remaining button. DO
while you press and release (“cycle”), your hand-held
NOT erase the channels.
transmitter every two seconds until HomeLinkt has
successfully accepted the frequency signal. The indicator If you unplugged the garage door opener/device for
light will flash slowly and then rapidly when fully programming, plug it back in at this time.
trained.
JOBNAME: CHRY OM (Contenta pu PAGE: 16 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 28DC2BF8
/chry_pdm/chrysler/owners/ctx/sim03.40.00
16
Reprogramming A Single HomeLinkt Button
Security
To reprogram a channel that has been previously trained, It is advised to erase all channels before you sell or turn
in your vehicle.
follow these steps:
To do this, press and hold the two outside buttons for
20 seconds until the red indicator flashes. Note that all
2. Press and hold the desired HomeLinkt button until
channels will be erased. Individual channels cannot be
the indicator light begins to flash after 20 seconds. Do not
erased.
release the button.
The HomeLinkt Universal Transceiver is disabled when
3. Without releasing the button proceed with
the Vehicle Security Alarm is active.
“Canadian/Gate Operator Programming” Step 2 and
Troubleshooting Tips
follow all remaining steps.
If you are having trouble programming HomeLinkt, here
Using HomeLinkT
are some of the most common solutions:
To operate, press and release the programmed
HomeLinkt button. Activation will now occur for the • Replace the battery in the original hand-held transmitprogrammed device (i.e., garage door opener, gate operater.
tor, security system, entry door lock, home/office light• Press the LEARN button on the Garage Door Opener
ing, etc.,). The hand-held transmitter of the device may
to complete the training for a Rolling Code.
also be used at any time.
1. Turn the ignition switch to the ON/RUN position.
JOBNAME: CHRY OM (Contenta pu PAGE: 17 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 199A08F0
/chry_pdm/chrysler/owners/ctx/sim03.40.00
17
• Did you unplug the device for programming and
remember to plug it back in?
If you have any problems, or require assistance, please
call toll-free 1–800–355–3515 or, on the Internet at
www.HomeLink.com for information or assistance.
WARNING!
• Your motorized door or gate will open and close
while you are programming the universal transceiver. Do not program the transceiver if people,
pets or other objects are in the path of the door or
gate. Only use this transceiver with a garage door
opener that has a “stop and reverse” feature as
required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener
without these safety features. Call toll-free 1–800–
355–3515
or,
on
the
Internet
at
www.HomeLink.com for safety information or assistance.
• Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run your vehicle in the garage
while programming the transceiver. Exhaust gas
can cause serious injury or death.
JOBNAME: CHRY OM (Contenta pu PAGE: 18 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1E9E26C3
/chry_pdm/chrysler/owners/ctx/sim03.40.00
18
General Information
This device complies with FCC rules Part 15 and Industry
Canada RSS-210. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be
received including interference that may cause undesired
operation.
NOTE:
• The transmitter has been tested and it complies with
FCC and IC rules. Changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority to operate the
device.
• The term IC before the certification/registration number only signifies that Industry Canada technical
specifications were met.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2012:01:03 09:31:46-05:00
Creator                         : XyEnterprise XPP 8.3C.1  SP #2
Modify Date                     : 2012:01:03 10:18:27-05:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : GPL Ghostscript 8.63
Creator Tool                    : XyEnterprise XPP 8.3C.1  SP #2
Metadata Date                   : 2012:01:03 10:18:27-05:00
Document ID                     : 367e7a4b-6e34-11ec-0000-bfa0bcd0c00d
Instance ID                     : uuid:925ccfa6-94be-4df3-906f-318d9f0e4fcf
Format                          : application/pdf
Title                           : CHRY OM (Contenta pu
Page Count                      : 18
Signing Date                    : 2012:01:03 10:18:27-05:00
Signing Authority               : ARE Acrobat Product v8.0 P23 0002337
Annotation Usage Rights         : Create, Delete, Modify, Copy, Import, Export
EXIF Metadata provided by EXIF.tools
FCC ID Filing: CB2SAHL5

Navigation menu