Jonter Digital L2 Bluetooth Speaker User Manual In the box
Shenzhen Jonter Digital Co., Ltd Bluetooth Speaker In the box
user manual
USER Manual Thanks to purchase our product. Please read the operation manual carefully for better operation and enjoy your music. What you got in the gift box? 1. L2 Bluetooth Speaker x 1 pcs 2. Micro USB chargeable cable x 1 pcs 3. 3.5mm Audio cable x 1 pcs 4. Instruction manual x 1 pcs Features 1. Bluetooth function 2. With Microphone, support hands free 3. Aux in, compatible with all 3.5 Audio Device 4. With Bass Diaphragm 5. Built-in 1200mAH Li-battery 6. Micro USB jack to charging. Specification Output power: 3W Frequency response: 90Hz~18KHz Impedance: 4OHM Sensitive: 80dB±2dB Dimension: 92*92*45mm S/N Ration: ≥65dB Distortion: ≤1% Power supply: Built-in battery or micro USB 5V Tone Summarize: Power on: 4 short beeps,then sound clip Battery low: 2 beeps Power off:4 short beeps Aux mode:2 beeps Connected: 4beeps Disconnected: no beep,sound clip Function: 1.Turn on and Turn off Press and hold seconds to turn off. about 3 seconds to turn on speaker, press again for 3 2. Volume - / Previous music Short press for previous music and long press for volume down 3. Volume+/ Next music Short press for next music and long press for volume up 4.Play/pause/disconnect Press Bluetooth. for play and pause, Long press for 3 second to disconnect 5.Change LED Mode Press to change LED light mode, press 3 seconds to turn off lights. PAIRING: 1.Turn your speaker on with “dididi” sound.the speaker was in defaulted Bluetooth mode with voice”The Bluetooth is ready to pair” 2.The Bluetooth indicator on the side of speaker will flash quickly 3.Turn on the bluetooth function of your device , search for “Gadget 8047793” and select it to pair. 4.If pairing is successful,you will hear a tone to confirm and the side led light will flash slowly. 5.Press 3seconds to disconnect. HANDS-FREE SPEAKERPHONE 1.Press the be paused. 2.Long press to pick up the call and playing music will automatically to reject the call 3.Press again to hangup the call when finished. The paused music will resume playing automatically LINE-IN With the speaker powered on, connect the included AUX cable into the port 9 on the side of the speaker and plug the other end into your phones aux port,then you can can play music via your phone. The button pls control via your devices. was not workable under line-in mode, Charging: Connect the speaker’s Micro USB socket 7 with theprovide charging cable,the power indicator 8 will show red while the battery is charging, when a full charge has been achieved the LED will turn off. 1.Battery: China battery 1200maH 2.Fully charge:2.5-3H 3.Play time: 5-6H When charging, the side indicator will turn red and when it fully charged the indicator will turn off NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference, and(2) this device must accept any interference, includinginterference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre lefonctionnement.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Tagged PDF : No XMP Toolkit : 3.1-701 Create Date : 2016:06:03 17:50:07+08:00 Creator Tool : Microsoft? Office Word 2007 Modify Date : 2016:06:08 17:07:34+08:00 Metadata Date : 2016:06:08 17:07:34+08:00 Format : application/pdf Creator : 微软用户 Title : In the box Producer : Microsoft? Office Word 2007 Document ID : uuid:b030e4b3-598f-4272-ac17-a265a18cb725 Instance ID : uuid:fce1354e-14c7-4cb4-a80e-258a375ad920 Page Count : 6 Language : zh-CN Author : 微软用户EXIF Metadata provided by EXIF.tools