Jorjin Technologies WG1300E00 Wireless LAN EM board for Module (802.11 bg) User Manual Statements

Jorjin Technologies Inc. Wireless LAN EM board for Module (802.11 bg) Statements

Contents

User Manual - Statements

Download: Jorjin Technologies WG1300E00 Wireless LAN EM board for Module (802.11 bg) User Manual   Statements
Mirror Download [FCC.gov]Jorjin Technologies WG1300E00 Wireless LAN EM board for Module (802.11 bg) User Manual   Statements
Document ID1740416
Application ID4MF7JcosI6YNzAwLKu7G3A==
Document DescriptionUser Manual - Statements
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize8.99kB (112412 bits)
Date Submitted2012-07-10 00:00:00
Date Available2012-07-10 00:00:00
Creation Date2012-06-26 16:43:24
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2012-07-06 14:14:48
Document TitleUser Manual - Statements
Document CreatorMicrosoft® Office Word 2007
Document Author: USER

Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains FCC ID:
WS2-WG1300E00”. The grantee's FCC ID can be used only when all FCC
compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2012:06:26 16:43:24Z
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2012:07:06 14:14:48+08:00
Metadata Date                   : 2012:07:06 14:14:48+08:00
Format                          : application/pdf
Creator                         : USER
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:1ab6fa49-d4d8-4624-a2de-ee1b4b73748c
Instance ID                     : uuid:85098b58-7706-4001-a413-09cbfce018ab
Page Count                      : 2
Language                        : zh-TW
Author                          : USER
EXIF Metadata provided by EXIF.tools
FCC ID Filing: WS2-WG1300E00

Navigation menu