Junlan Electronic CAB0111 Bluetooth Speaker User Manual BT111GB English manual

Shenzhen Junlan Electronic Ltd Bluetooth Speaker BT111GB English manual

User manual

BLUETOOTH SPEAKER SYSTEMInstruction ManualModel: BT111GBRead these instructions carefully before use
Safety instructionsPlease avoid placing the unit in places with high humidity, high temperature, grease, contamination, etc. Please do not place the unit in direct sunlight or rain. Avoid dropping the unit.When the unit gets dirty on the surface, please clean with damp cloth. Do not use any organic solvents, paint thinner or abrasive cleaners.Never privately dissemble, repair or modify unit. Contact our service center for repair information1
LOCATION OF CONTROLS2121. Indicators 2. Speakers3. Power ON/OFF switch4. USB Charger: USB cable only for charging5. Line in jack6. Hands-off/Power button7. Volume+- button8. / Previous/Next button3 4 5678USB CHARGER
Bluetooth Connection 3Line in connection1. Connect an audio connection cable with 3.5mm stereo plug (not included) to the line in jack on the rear of the unit.2. Connect the other end to the audio out jack/ phone jack on the MP3 or other external device.3. Turn on the external device and press Play button to start playing the music.4. Press + button to increase the volume. Press- button to decrease the volume.1.Connect the Bluetooth speaker via USB cord (included).2.Move the Power On/Off button on the rear of the unit to On position. The red indicator light will come on.3.Press the Power Button on the right side of the unit to turn on the unit. The blue indicator light will turn on and flash. Press and hold Power Button to turn the unit to Standby mode. During playback, press Power Button to pause and press again to resume the playback. When the unit is powered on the Bluetooth indicator blue light will turn on and flash and the unit will enter Bluetooth mode.4.Allow your cell phone to enter the Bluetooth connection mode. During searching, the blue Bluetooth indicator will keep flashing. When searching is completed, select BT111 as the target equipment. When connected, the Bluetooth indicator blue light will stay lit.5. Press. to skip to the previous track. Press to skip to the next track.6. Press + button to increase the volume. Press- button to decrease the volume.7. The built-in Mic of this unit enables hands-free function in Bluetooth mode. When the call comes in press Hands-free button to answer the call. Press Hands-free button again to hang up. Press Hands-free button to redial the last outgoing call.
Battery ChargingThe unit provides a built-in 3.7V 1000mAh Lithium battery. The standard voltage is 3.7V. The maximum voltage is 4.2V.1. The minimum working voltage of the unit is 3.5V.When the battery voltage is under 3.5V, the red indicator will stay lit to indicate the low voltage status and the battery needs to be recharged.2. Connect one end of the USB charging cable (included) to the DC in jack on the rear of the unit. Connect the other end to your PC. Or you can connect the other end to a 5V AC/DC adapter (not included) to power and charge the unit. Then the green indicator will stay lit to indicate that the battery is in charging status.3. When the voltage reaches the Maximum voltage 4.2V, the green indicator will turn off to indicate that the charging process is completed.4
SPECIFICATIONSBluetooth technology 2.0+EDRRMS Output 2x 2WEffective distance of Bluetooth approximately 33 feetSpeaker impedance 4 Ohm 3Wx2Playback timeACCESSORIESUser Manual 1PCUSB charging cable 1PC5approximately 3 hours(With volume set to ½ of Maximum volume)
TROUBLE SHOOTING GUIDECheck the followings before requesting service:SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTIONNo powerNo soundBluetooth reception failureHands free not workingThe built-in battery runs outPower switch is in OFF positionPower button on the unit not pressedRecharge the batteryMove the power switch on the rear of the unit to ON positionPress the POWER button on the right side of the unit to turn on the unitVolume in minimum position of the unitThe connected device is not in playback modeSound output of the connected device weakInput source incorrectRaise volume by pressing the VOL+ buttonPlay the music in the connected deviceRaise the volume level of the connected deviceSet input source as Line-in orBluetooth modeNot in Bluetooth modeLine in cable in the Line in jackSet to Bluetooth mode and the blue indicator will turn onDisconnect the line in cableNot in Bluetooth modeSet as Bluetooth mode(Hands free function is only available in Bluetooth mode)6
7LIMITED WARRANTY
FCC Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Navigation menu