Junlan Electronic CAB0111 Bluetooth Speaker User Manual BT111GB English manual
Shenzhen Junlan Electronic Ltd Bluetooth Speaker BT111GB English manual
User manual
Instruction Manual BLUETOOTH SPEAKER SYSTEM Model: BT111GB Read these instructions carefully before use Safety instructions Please avoid placing the unit in places with high humidity, high temperature, grease, contamination, etc. Please do not place the unit in direct sunlight or rain. Avoid dropping the unit. When the unit gets dirty on the surface, please clean with damp cloth. Do not use any organic solvents, paint thinner or abrasive cleaners. Never privately dissemble, repair or modify unit. Contact our service center for repair information LOCATION OF CONTROLS USB CHARGER 1. Indicators 2. Speakers 3. Power ON/OFF switch 4. USB Charger: USB cable only for charging 5. Line in jack 6. Hands-off/Power button 7. Volume+- button 8. Previous/Next button Bluetooth Connection 1.Connect the Bluetooth speaker via USB cord (included). 2.Move the Power On/Off button on the rear of the unit to On position. The red indicator light will come on. 3.Press the Power Button on the right side of the unit to turn on the unit. The blue indicator light will turn on and flash. Press and hold Power Button to turn the unit to Standby mode. During playback, press Power Button to pause and press again to resume the playback. When the unit is powered on the Bluetooth indicator blue light will turn on and flash and the unit will enter Bluetooth mode. 4.Allow your cell phone to enter the Bluetooth connection mode. During searching, the blue Bluetooth indicator will keep flashing. When searching is completed, select BT111 as the target equipment. When connected, the Bluetooth indicator blue light will stay lit. 5. Press. to skip to the previous track. Press to skip to the next track. 6. Press + button to increase the volume. Press- button to decrease the volume. 7. The built-in Mic of this unit enables hands-free function in Bluetooth mode. When the call comes in press Hands-free button to answer the call. Press Hands-free button again to hang up. Press Hands-free button to redial the last outgoing call. Line in connection 1. Connect an audio connection cable with 3.5mm stereo plug (not included) to the line in jack on the rear of the unit. 2. Connect the other end to the audio out jack/ phone jack on the MP3 or other external device. 3. Turn on the external device and press Play button to start playing the music. 4. Press + button to increase the volume. Press- button to decrease the volume. Battery Charging The unit provides a built-in 3.7V 1000mAh Lithium battery. The standard voltage is 3.7V. The maximum voltage is 4.2V. 1. The minimum working voltage of the unit is 3.5V.When the battery voltage is under 3.5V, the red indicator will stay lit to indicate the low voltage status and the battery needs to be recharged. 2. Connect one end of the USB charging cable (included) to the DC in jack on the rear of the unit. Connect the other end to your PC. Or you can connect the other end to a 5V AC/DC adapter (not included) to power and charge the unit. Then the green indicator will stay lit to indicate that the battery is in charging status. 3. When the voltage reaches the Maximum voltage 4.2V, the green indicator will turn off to indicate that the charging process is completed. SPECIFICATIONS Bluetooth technology 2.0+EDR RMS Output 2x 2W Effective distance of Bluetooth approximately 33 feet Speaker impedance Playback time 4 Ohm 3Wx2 approximately 3 hours (With volume set to ½ of Maximum volume) ACCESSORIES User Manual 1PC USB charging cable 1PC TROUBLE SHOOTING GUIDE Check the followings before requesting service: SYMPTOM No power POSSIBLE CAUSE The built-in battery runs out Power switch is in OFF position POSSIBLE SOLUTION Recharge the battery Move the power switch on the rear of the unit to ON position Press the POWER button on the right side of the unit to turn on the unit Volume in minimum Raise volume by pressing the position of the unit VOL+ button The connected device is Play the music in the not in playback mode connected device Raise the volume level of the Sound output of the connected device weak connected device Set input source as Line-in or Input source incorrect Bluetooth mode Set to Bluetooth mode and the Not in Bluetooth mode blue indicator will turn on Power button on the unit not pressed No sound Bluetooth reception failure Hands free not working Disconnect the line in cable Line in cable in the Line in jack Set as Bluetooth mode(Hands free function is only available in Bluetooth mode) Not in Bluetooth mode LIMITED WARRANTY FCC Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.0-c320 44.284297, Sun Apr 15 2007 17:19:00 Creation Date--Text : Producer : Corel PDF Engine Version 14.0.0.653 Mod Date--Text : Format : application/pdf Creator : Administrator Title : BT111GB English manual.cdr Creator Tool : CorelDRAW Modify Date : 2012:09:19 09:31:58+08:00 Metadata Date : 2012:09:19 09:31:58+08:00 Document ID : uuid:d740ae94-f79c-41fc-868b-edfce58b25e2 Instance ID : uuid:d6d836d2-1fb1-41e2-b1f2-e3965843c8bd Page Count : 9 Create Date : D:20120914113114Z Author : AdministratorEXIF Metadata provided by EXIF.tools